A novel method for preparing monodispersed polystyrene nanoparticles

A preparation manner for monodispersed polystyrene (PS) nanoparticles polymerized by using a novel addition procedure of a monomer is suggested. In systems containing a smaller amount of surfactant compared with conventional microemulsion polymerization, the polymerization processes consists of three stages: adding dropwise the first part of the monomer for a few minutes at 80°C and polymerizing for 1 h; adding collectively the residual part of the monomer and polymerizing at the same temperature for another 1 h; and then polymerizing at 85°C for another 1 h. Based on discussions on the nucleation mechanism of particles in the polymerization system, the influences of monomer weight added dropwise, and amounts of initiator and emulsifier on the size and distribution of PS particles were investigated. PS nanoparticles with smaller diameter such as a number-average diameter of 18.7 nm and better monodispersity were obtained since the dropped styrene amount was suitable under 20wt-% emulsifier amount and 3wt-% initiator amount based on the monomer. Translated from Journal of Nanjing University (Natural Science), 2006, 2 (in Chinese)     

Problems associated with the surface characterization of polystyrene latices

It has been shown that polystyrene latices prepared by the surfactant free emulsion polymerization process often contain sufficient residual monomer and possibly low-molecular-weight material and reaction by-products, such as benzaldehyde, which are not efficiently removed by dialysis, to affect their bulk and surface characteristics. These materials have been identified by gel permeation chromatography (GPC) and infrared (IR) spectroscopy studies and their effective removal by steam stripping has been investigated. Steam stripping has proved to be efficient in this process but it led to rapid hydrolysis of the surface sulfate groups and a consequent change in the surface characteristics. The problem of hydrolysis of sulfate groups under various environments has been studied. The problems associated with the identification of weak acid end groups are discussed and several alternative explanations for their occurrence are advanced.     

Preparation of monodisperse polystyrene latices

Summary A series of monodisperse polystyrene latices was prepared by using the direct and the seeding emulsion polymerization methods. The recipes for their preparation are given in full detail. Best results were obtained when using Aerosol MA (a surfactant of the sulfosuccinate series) as the emulsifier. The particle size distributions were evaluated from electron microscopic data. The average size of latex particles ranged from 200 to 950 m. The polydispersity ratios being very near unity and modal frequencies about 95% indicate a very high monodispersity of latex preparations. The reproducibility of the particle size distribution parameters was remarkably good. Significant deviation from theSmith-Ewart mechanism was found. A possible mechanism of the emulsifier action in the formation of monodisperse latices is postulated.

---

Zusammenfassung Es wurde eine Serie von monodispersen Polystyrollatices dargestellt. Die experimentellen Bedingungen, unter welchen monodisperse Latices entstehen, wurden untersucht. Die Vorschriften sind genau angegeben. Mit Aerosol MA (einem oberflächenaktiven Mittel der Sulfosuccinatserie) als Emulgator wurden die besten Ergebnisse erhalten. Mittels Elektronenmikroskopie wurde die Verteilung der Teilchengrößen ermittelt. Die durchschnittliche Größe der Latexteilchen lag zwischen 200 und 950 m. Die Polydispersitätsquotienten lagen in unmittelbarer Nähe von 1, und die modalen Frequenzen um 95% indizierten eine sehr hohe Monodispersität der Latexproben. Die Reproduzibilität der Teilchengröße-Verteilung-Parameter war besonders ausgeprägt. Es wurde eine Abweichung vomSmith-Ewart-Mechanismus beobachtet. Der mögliche Mechanismus der Emulgatorwirkung bei Entstehung der monodispersen Latices wurde diskutiert.

---

---

With 7 figures and 8 tables     

Differential thermal analysis of negatively charged polystyrene latices

To study vicinal water structure around polystyrene latex particles differential thermal analysis (DTA) has been utilized. Measurements of programmable water thermodesorption from polystyrene surfaces under dynamic and quasiisothermal conditions were made. Therefore, the adsorption potential distribution function was calculated and the hydrophobicity of polystyrene surfaces determined. DTA is presented as a useful method to study the interfacial properties of polymer colloids.     

大比表面负载氧化铁的氧化硅层柱磷酸锆制备和 催化性能研究

提出了一种以氧化硅层柱磷酸锆(SiO~2-ZrP)的前驱体,氨丙基硅酸酯嵌入磷酸锆(APS-ZrP)为载体制备负载氧化铁的氧化硅层术磷酸锆的新方法。与传统方法相比,新方法制得的样品具有较大的比表面和孔容。X射线粉末衍射(XRD)和程序升温还原(TPR)的结果表明采用新方法有利于氧化铁在载体表面的高度分散,分散阈值为0.25gFe~2O~3/g(SiO~2-ZrP),远超过直接以SiO~2-ZrP为载体浸渍草酸铁铵的传统方法得到样品。同时,用新方法制得的氧化铁催化剂表现了较高的乙苯脱氢活性,是一类值得研究的催化材料。     

Adsorption of different amphiphilic molecules onto polystyrene latices

In order to know the influence of the surface characteristics and the chain properties on the adsorption of amphiphilic molecules onto polystyrene latex, a set of experiments to study the adsorption of ionic surfactants, nonionic surfactants and an amphiphilic synthetic peptide on different latex dispersions was performed. The adsorbed amount versus the equilibrium surfactant concentration was determined. The main adsorption mechanism was the hydrophobic attraction between the nonpolar tail of the molecule and the hydrophobic regions of the latex surface. This attraction overcame the electrostatic repulsion between chains and latex surface with identical charge sign. However, the electrostatic interactions chain-surface and chain-chain also played a role. General patterns for the adsorption of ionic chains on charged latex surfaces could be established. Regarding the shape, the isotherms presented different plateaus corresponding to electrostatic effects and conformational changes. The surfactant size also affects the adsorption results: the higher the hydrophilic moiety in the surfactant molecule the lower the adsorbed amount.     

Nonionic latices in aqueous media part 1. Preparation and characterization of polystyrene latices

A series of non-ionic polystyrene latices in aqueous media containing particles with a narrow size distribution have been prepared using a nonyl phenol poly(ehylene glycol) condensate as the surfactant, methoxy poly(ethylene glycol methacrylate) as the comonomer/stabilizer, and ascorbic acid/hydrogen peroxide as the initiator system. As a control synthesis for comparison with the above latex, a charge stabilized polystyrene latex was prepared, using an anionic surfactant and potassium persulphate as the initiator. Latices employing a combination of charge plus steric stabilization mechanisms were also prepared, in order to investigate the effect of the non-ionic surfactant and the comonomer/stabilizer. The particle size of the latices was measured by transmission electron microscopy, the surface charge density by conductimetric titration and the glass transition temperature of the polymer by differential scanning calorimetry. The latex prepared using non-ionic ingredients, showed no titratable charge and exhibited a profound lowering of the glass transition temperature, with respect to the charge stabilized latex. On the basis of these results, schematic models for the polymerization mechanism and the morphology of the latex particles are proposed.     

A study of some of the rheological properties of concentrated polystyrene latices

Monodisperse latices form highly ordered but liquid-like structured dispersions at moderate to high concentrations. The rheological measurements show such systems to be viscoelastic. Shear wave propagation and creep compliance measurements have been carried out as a function of volume fraction using polystyrene latices in dilute electrolyte. These measurements enabled the high frequency limiting modulus and the zero shear rate viscosity to be obtained.The data are compared with predictions from models based on the perturbation of ordered particle structures, the magnitude of the particle pair potentials and the restricted diffusive motion of particles in the structures.     

Phenanthroline method for quantitative determination of surface carboxyl groups on carboxylated polystyrene particles with high sensitivity

This study developed a phenanthroline method for quantitative determination of surface carboxyl groups on carboxylated polystyrene (PS‐COOH) particles based on the coordination between the carboxyl groups and Fe²⁺. The ratio of the carboxyl groups, which is determined by conductometric titration method, to Fe²⁺ coordinated with the particles, which is determined by phenanthroline method, is 4.7, i.e. n_COOH = 4.7 × Δn_Fe²⁺. The Lambert–Beer law is obeyed in the range of 0–60 × 10^?9 mol/ml for the amount of surface carboxyl on the particles. The detection limit of the method is 2 nmol COOH/ml. The average standard deviation of the experiments is 4.4%. The relative deviation of the data obtained with this method is lower than 7% compared with that obtained with the conductometric titration method. The weight of the sample necessary for phenanthroline method is only about 0.1% of that necessary for conductometric titration method. It has been demonstrated that the phenanthroline method is suitable for quantitative determination of low amount of surface carboxyl groups on PS‐COOH particles due to its high sensitivity. Copyright © 2009 John Wiley & Sons, Ltd.     

A new method for preparing dimethylamino-B-difluoroborine

Summary We have worked out a new method for preparing dimethylamino-B-difluoroborine by splitting hydrogen fluoride from dimethylamino-B-trifluoroborine by heating with aluminum powder in a medium of vaseline oil.     

Studies on the preparation and characterization of monodisperse polystyrene latices. VI. Preparation of zwitterionic latices

The preparation of zwitterionic latex particles is reported by using a mixed anionic and cationic initiator system without requiring surface-active agents. Isoelectric points were found from microelectrophoresis experiments and were in the pH range of 3.5-5. Close to the isoelectric point, the latices coagulated as expected, and good stability was achieved outside this narrow range. This range of stability was in good agreement with predictions from current theory. Redispersion after coagulation was found to be difficult as was expected for a hydrophobic colloid. The electrokinetic behavior did not result in the maximum in zeta potential at an electrolyte concentration of 1 mM unlike the situation for other hydrophobic polystyrene latex particles, and hence these systems may be even better models for other colloidal studies.     

A general method for preparing diphosphiranes

Diphosphiranes 3a-3f are obtained by action of diazo derivatives and carbenes on the trans-diphosphene 1. The structures are elucidated by spectroscopic methods. In all cases the cycloaddition reaction is stereoselective.     

A new method for preparing carbenes

Russian Chemical Bulletin -     

Studies on the preparation and characterization of monodisperse polystyrene latices V.: The preparation of cationic latices

Summary Methods are described for the preparation of monodisperse polystyrene latices using as initiators, 2-azo-bis-(2-methylpropamidinium) dichloride and 2-azo-bis-(2-isopropyliminazolium) dichloride. The preparations were carried out in the absence of any added surface active agents. The effect on particle size of varying initiator concentration, monomer concentration, temperature and ionic strength was examined and the conditions defined for preparing monodisperse latices, with particles in the size range 0.2 to 1m. Electrophoretic measurements confirmed that the latex particles were cationic. The evidence obtained suggested that the charged sites on the particle surface were amidinium groupings. The latices were not stable at pH values greater than 11 and prolonged heating at 90° also caused coagulation.

---

Zusammenfassung Es wurden Methoden zur Darstellung monodisperser Polystyrol-Latices unter Verwendung von 2-azo-bis-(2-methylpropamidinium)-dichlorid und 2-azo-bis-(2-isopropyliminazolium)-dichlorid als Initiator beschrieben. Die Darstellung erfolgte in Abwesenheit von grenzflächenaktiven Verbindungen. Der Einfluß unterschiedlicher Initiator- und Monomerkonzentrationen, der Temperatur und der lonenstärke auf die Teilchengröße wurde untersucht und die Bedingungen festgelegt, unter denen monodisperse Latices mit Teilchen im Größenbereich von 0,2-1m erhalten werden. Elektrophoretische Messungen bestätigten, daß die Latexteilchen kationisch sind. Die Ladungen auf der Teilchenoberfläche sind Amidiniumgruppen. Die Latices waren bei pH-Werten über 11 nicht stabil; längeres Erhitzen auf 90° führte ebenfalls zur Koagulation.

---

---

With 6 figures and 9 tables     

Studies of particle-particle interactions using polystyrene latices and time-average light scattering

Dilute dispersions of monodisperse negatively-charged polystyrene latex particles, radii 161 Å, have been examined by time-average light scattering at various latex volume fractions and electrolyte concentrations. The latter were varied from the low value produced by maintaining mixed bed ion-exchange resin beads in the systems (ca. 10^–5 mol dm^–3) to the value of 5×10^–3 mol dm^–3 obtained by the addition of sodium chloride. From angular scattering measurements determinations of the structure factors were made; these were produced as a consequence of the particle-particle interactions in the system. By extrapolation of the structure factor to zero scattering angle, values were obtained for the osmotic compressibility and hence the osmotic pressure of the systems as a function of the latex volume fraction. It was found that the experimental data obtained could be interpreted in terms of a hard-sphere model for the particle-particle interaction. Good agreement was obtained provided that the particles were assigned a hard-sphere radius which was determined by the electrostatic repulsion between the particles.