Thermal decomposition of poly(vinyl chloride) and chlorinated poly(vinyl chloride). II. Organic analysis

A concerted study of poly(vinyl chloride), chlorinated poly(vinyl chloride), and poly(vinylidene chloride) polymers by spectroscopy, thermal analysis, and pyrolysis-gas chromatography resulted in a proposed mechanism for their thermal degradation. Polymer structure with respect to total chlorine content and position was determined, and the influence of these polymer units on certain of the decomposition parameters is presented. Distinguishing differences were obtained for the kinetics of decomposition, reactive macroradical intermediates, and pyrolysis product distributions for these systems. It was determined that chlorinated poly(vinyl chloride) systems with long-chain ? CHCI? units were more thermally stable than the unchlorinated precursor, exhibited increasing activation energy for the dehydrochlorination, and produced chlorine-containing macroradical intermediates and chlorinated aromatic pyrolysis products. The poly(vinyl chloride) polymer was relatively less thermally stable, exhibited decreasing activation energy during dehydrochlorination, and produced polyenyl macro-radical intermediates and aromatic pyrolysis products.     

Measurements of the relaxation spectra of unplasticized poly(vinyl chloride) melts

We have measured the relaxation modulus in the temperature range 150–220°C of two samples of poly(vinyl chloride) resin with different molecular weights. The data were treated by the principle of reduced variables to yield composite curves. The shift factors (a_T) when plotted against reciprocal temperature gave good straight lines from which apparent activation energies were obtained. An apparent activation energy of 50 kcal/mole was obtained for both samples. A relaxation spectrum for each resin was calculated from the relaxation modulus data. These spectra showed a marked molecular weight dependence. The spectra were in the range characteristic of the terminal zone of the entanglement plateau. Zero-shear-rate viscosities were obtained from the integration of relaxation modulus plots. From extrapolation of capillary viscosity data it is shown that the viscosity of the higher molecular weight resin used in this study does not approach its zero-shear value until shear rates less than 10^?3 sec^?1 are reached. The effect of supermolecular flow units is briefly discussed.     

Investigations on poly(vinyl chloride). II. Pyrolysis of chlorinated polybutadienes as model compounds for poly(vinyl chloride)

The pyrolysis of chlorinated polybutadienes (CPB) was investigated by using a pyrolysis gas chromatograph. CPB corresponds to poly(vinyl chloride) (PVC) constructed with head–head and tail–tail linkages of the vinyl chloride unit. Benzene, toluene, ethyl-benzene, o-xylene, styrene, vinyltoluene, chlorobenzenes, naphthalene, and methylnaphthalenes were detected in the pyrolysis products from CPB above 300°C, and no hydrocarbons could be detected at 200°C. The pyrolysis products from CPB were similar to those from PVC and new products could not be detected. Lower aliphatics, toluene, ethylbenzene, o-xylene, chlorobenzenes, and methylnaphthalenes were released more easily from pyrolysis of CPB than from PVC; amounts of benzene, styrene, and naphthalene formed were small. These results support the conclusion that recombination of chlorine atoms with the double bonds in the polyene chain takes place and that scission of the main chain may depend on the location of methylene groups isolated along the polyene chain during the thermal decomposition of PVC.     

Dynamic mechanical properties of plasticized poly(vinyl chloride)

The complex compliance in extension of gels of poly(vinyl chloride) (PVC) in di(2-ethylhexyl) phthalate (DOP) and in tricresyl phosphate (TCP) was measured over the frequency range from 0.6 to 0.006 cps and the temperature range from ?66 to 65°C: the weight fractions of DOP and TCP in the gels were 0.32, 0.40, 0.49, and 0.59. Measurements were carried out in an apparatus using forced low-frequency longitudinal osillations. Data for the gels could not be combined by the method of reduced variables, since there were gradual changes with decreasing temperature, attributable to an increase in crystallinity. Application of the reduction method of Ninomiya and Ferry for solutions of crystalline polymers was found to be successful. The apparent melting temperatures (T′_m) were obtained from the temperature dependence of the vertical shift factors. An apparent heat of fusion of ca. 120 cal/mole of monomer unit was found. This melting range was in agreement with that of secondary crystallinity in plasticized PVC reported in calorimetric studies by Juijn. With decreasing temperature, two phenomena occurred in the temperature range from T_g + ca. 80°C to T_g: the vitrification of a concentrated amorphous solution and the slight crystallization of the polymeric component. The larger the difference between T_g and T′_m the broader the primary dispersion zone on the frequency scale. This broadening effect was explained as due to the difference in dependence of T_g and T′_m on plasticizer concentration, without any need to consider any specific interaction between plasticizer and PVC.     

Modification of poly(vinyl chloride). XIII. Crosslinking of poly(vinyl chloride) with dithiols and properties of the crosslinked products

PVC was crosslinked by immersing PVC–dithiol blends in ethylenediamine at 30°C. Properties of the products depended on the chain length and chemical structure of the crosslinkage and on the molecular weight of the polymer chain between crosslinks M_c. Crosslinking by the agent of soft structure and long molecular chain resulted in high tensile strength at break and impact strength and low brittle temperature. The use of the crosslinking agent of short molecular chain gave high yield strength, Young's modulus, and heat distortion temperature. The relation of M_c and the chemical structure of the crosslinks to the properties of the crosslinked rigid polymer was discussed in regard to the crosslinking effect and plasticizing effect.     

Mechanical properties of blends of PAMAM dendrimers with poly(vinyl chloride) and poly(vinyl acetate)

Hybrid blends of poly(amidoamine) PAMAM dendrimers with two linear high polymers, poly(vinyl chloride), PVC, and poly(vinyl acetate), PVAc, are reported. The interaction between the blend components was studied using dynamic mechanical analysis, xenon nuclear magnetic resonance (NMR) spectroscopy, and tensile property measurements. The data suggest a much higher degree of interaction between components of PVAc-containing blends compared to those containing PVC. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2111–2117, 1998     

Structure and solution properties of radical-initiated poly(vinyl chloride). II. Correlation of solution properties

The results of detailed measurements of osmotic pressure, light scattering, and viscosity of poly(vinyl chloride) solutions are used to establish the molecular weight dependence of [η] and A₂, to estimate the unperturbed dimensions of the poly(vinyl chloride) molecule, and to analyze critically the [η]–M correlations published hitherto.     

Structure of chlorinated poly(vinyl chloride). V. Molecular parameters of chlorinated poly(vinyl chloride)

The molecular parameters of samples of chlorinated poly(vinyl chloride) (CPVC) and chlorinated β,β-dideuterated poly(vinyl chloride) (β,β-d₂-CPVC) were determined by gel permeation chromatography (GPC), light scattering, osmometry, and viscometry. Comparison of GPC, light scattering, osmometric, and viscometric data resulted in a discussion of the possibility of degradation and the causes of changes in the solution properties in chlorination of PVC and ββ-dideuterated poly(vinyl chloride) (ββ-d₂-PVC). The results obtained are discussed in relation to the mechanism of chlorination of PVC.     

Some optical and mechanical properties of poly(vinyl chloride)

The optical and mechanical properties of poly(vinyl chloride) film were examined by observing both the stress and birefringence during stretching at constant rate, during relaxation at constant length and during a dynamic birefringence experiment. Experiments were also done by varying the temperature at constant length. The changes in birefringence are interpreted in terms of changes in negative distortional birefringence, changes in positive orientation birefringence, and possible reversible changes in birefringence with temperature arising from conformational changes in the polymer chain and changes in the contribution of birefringent crystals.     

Photo-oxidation of poly(vinyl chloride)

The photo-oxidation of PVC has been studied over the temperature range 30–150°C. Initiation with ultraviolet (2537A) radiation has been correlated with the presence of minute amounts of ozone. The contribution of atomic oxygen and singlet oxygen (¹Δ_g) molecules to the initiation mechanism is discussed. The β-chloroketones probably formed in the photo-oxidation of PVC, decomposed according to a Norrish type I reaction without loss of chlorine atoms. The gaseous products of the photo-oxidation of PVC at 30°C were carbon dioxide, carbon monoxide, hydrogen, and methane. Hydrogen chloride was obtained only when PVC was heated at high temperatures. When PVC was photo-oxidized and then heated at high temperature, benzene was obtained in addition to hydrogen chloride. The gaseous products from the photo-oxidations of model compounds, such as 4-chloro-2-butanone and 2,4-dichloropentane, were also compared with those from PVC. Hydrogen chloride was detected only after photo-oxidation at temperatures of 25°C or higher. Therefore, it was concluded that hydrogen chloride is mainly a product of thermal decomposition. Since unsaturation was not observed in photo-oxidized PVC films, the cause of discoloration is unclear. When PVC was modified by stabilizers or additives, the oxidative degradation was further complicated by side reactions with the additives.     

Pyrolysis of poly(vinyl chloride)

A pyrolysis–gas chromatography–mass spectrometric technique has been developed to study the thermal degradation of poly(vinyl chlorides) polymerized at different temperatures. Hydrogen chloride and benzene evolution during successive stages of pyrolysis have been quantitatively determined and correlated to the tacticity and molecular weight of the polymer. It was found that lowering the temperature of polymerization and molecular weight depresses benzene evolution and increases char weight but does not affect the HCl yield. It is suggested that the syndiotactic trans microstructure favored at low temperature of polymerization yields polyenes which cannot cyclize to form benzene. As the molecular weight decreases, the increase in number of vinyl chain ends facilitates pyrolytic crosslinking and char formation.     

Photosensitized dehydrochlorination of poly(vinyl chloride). III. Reaction of thermally degraded poly(vinyl chloride) with hydrogen chloride

Films prepared from thermally degraded poly(vinyl chloride) were photolyzed in the presence of hydrogen chloride. When the light was filtered through a Pyrex disk, the absorbance in the region between 270 nm and about 415 nm decreased and reached a minimum value but the absorbance increased at wavelengths shorter than 270 nm and longer than 415 nm. Maximum bleaching occurred at a wavelength which depended on that of the irradiating light. When the Pyrex filter was omitted, an additional slower photodehydrochlorination reaction was superimposed on the photobleaching reaction. Photolysis of hexane or ethanol solutions of 1,8-diphenyloctatetra-1,3,5,7-ene and hydrogen chloride showed a similar reaction involving bleaching of the absorption of the polyene structure. The problems of using absorbance as an indication of the extent of the photodegradation of poly(vinyl chloride) are discussed.     

Photo-oxidation of poly(vinyl chloride)

Hydrogen chloride is evolved at an increasing rate in the light-induced oxidation of poly(vinyl chloride) films. These accelerated kinetics were shown to result from an increased absorption of light by the polyenes formed, since the quantum yield of dehydrochlorination (Φ_HCl = 0·015) is independent of the extent of the reaction in the dose range investigated. Determination of the quantum yields of the different processes involved indicate that, for each scission of the polymer backbone, 11 molecules of hydrogen chloride are evolved while three carbonyl groups, two hydroperoxides and 0·4 intermolecular crosslinks appear on the polymer chain. A mechanism that involves β-scissions of the tertiary alkoxy radicals, resulting from non-terminating interactions of α-chloro-peroxy radicals, is suggested to explain the observed increase of the polymer degradation in the presence of oxygen.     

Radiolysis of poly(vinyl chloride)

Allyl free-radical intermediates are detected by ultraviolet absorption at 255 mu in poly(vinyl chloride) irradiated at ?196°C and stored at 25°C. In vacuum at 25°C, allyl radicals are converted into polyenyl free radicals and polyenes. From the nature of allyl radical decay in vacuum, radical chain transfer between polyenyl radicals and poly(vinyl chloride) is inferred. Allyl and polyenyl free radicals are scavenged by oxygen on post-irradiation storage in air.     

Compatibility of poly(vinyl chloride) with polyalkyleneoxides. II. Poly(propylene oxide) and poly(tetramethylene oxide)

This study [Part II of a series dealing with the compatibility of polyalkyleneoxides with poly(vinyl chloride)] examines blends of PVC with poly(propylene oxide) (PPrO) and poly(tetra-methylene oxide) (PTMO), covering the entire composition range. Morphological, dynamic mechanical and thermal properties investigated indicate that PVC/PPrO blends are incompatible, whereas the PVC/PTMO system shows miscibility in the melt. For this polyblend and at high polyether compositions where the Hoffman–Weeks analysis can be applied, T_m equilibrium data allow the determination of the thermodynamic interaction parameter, χ₁₂ = ?0.15. Experimental compatibility data of all polyether-PVC pairs investigated in Parts I and II are also used to test various blend miscibility prediction schemes, using solubility parameter theory and recent theory on copolymer-copolymer miscibility.     

Relaxation properties of plasticised poly(vinyl chloride) and PVC blends

The temperature-frequency dependence of dielectric parameters for several PVC-plasticizer systems and PVC blends was obtained. Kinetic and activation parameters and α-relaxation spectra were estimated. The increase of the polar group number and size in the plasticizer molecules results in the narrowing of the relaxation spectra and in the increase of inner mobility of PVC segments. It was found for PVC-ABS and PVC-Paraloid blends that all relaxation characteristics depend on the miscibility of components. The results were also confirmed by the cloud point data.     

Morphology and properties of poly(vinyl chloride)–poly(butadiene-co-acrylonitrile) blends

The objective of this research was to study the structure-property relationships of two poly(vinyl chloride) (PVC)–poly(butadiene-co-acrylonitrile) (BAN) blends which exhibit differences in blend compatibility. Studies were carried out utilizing differential scanning calorimetry, dynamic mechanical testing, stress–strain, transmission electron microscopy (TEM), and infrared dichroism experiments at different temperatures. The BAN 31/PVC (BAN containing 31% acrylonitrile) system is considered to be nearly compatible as evidenced by T_g shifts, stress–strain results, orientation characteristics, and TEM micrographs. Similar experiments indicate that the BAN 44/PVC system is incompatible, and contains a mixed phase of BAN 44-PVC and a pure BAN 44 phase. The extent of heterogeneity in the compatible BAN 31/PVC system, however, plays an important role in the orientation characteristics of the blends.