一种新的4,6-二氨基间苯二酚盐酸盐的制备方法及与对苯二甲酸的缩合聚合

以间苯二酚为原料,通过乙酰化、肟化、Beckmann重排、水解反应制备4,6-二胺基间苯二酚盐酸盐(DAR·2HCl),并用FTIR,MS,元素分析,¹HNMR和¹³CNMR等对DAR·2HCl及中间体进行了表征.同时,将DAR·2HCl和对苯二酸(TPA)成盐,然后进行缩聚得到具有较高分子量的PBO.通过FTIR和固体¹³CNMR表征了PBO的结构,并研究了PBO的热性能.     

基于液态聚碳硅烷的聚铝碳硅烷的合成与表征

采用液态聚碳硅烷与乙酰丙酮铝在常压下反应合成了具有不同铝含量的聚铝碳硅烷(PACS), 由于不需要循环回流过程, 因此该方法简单方便, 安全性高. 在与合成聚铝碳硅烷相同的条件下, 对单纯的液态聚碳硅烷原料进行保温处理, 所得产物的分析表征结果显示, 该原料在反应条件下基本保持稳定, 不会自聚或者裂解. 不同铝含量的聚铝碳硅烷的元素分析结果表明, 随着乙酰丙酮铝加入量的增加, 聚铝碳硅烷中的铝含量增加, 同时氧含量增加, 氢含量减少, 且乙酰丙酮铝中的铝元素几乎全部引入到液态聚碳硅烷中. GPC分析结果显示, 随着铝含量的增大, PACS的数均分子量增大, 分子量分布变宽. 红外光谱和核磁共振波谱分析结果表明, 液态聚碳硅烷与乙酰丙酮铝的反应主要以消耗Si-H键的方式进行, 铝元素以AlO₄, AlO₅和AlO₆ 3种配位形式存在, 同时形成Si-O-Al交联键, 使得聚铝碳硅烷的分子量增大, 分子量分布变宽.     

ABA型聚L-丙氨酸-聚乙二醇嵌段共聚物的合成及其表征

利用L-α-丙氨酸和三聚光气反应制备了N-羧基-α-丙氨酸-环内酸酐(NCA).以聚乙二醇(PEG)为原料.制备了端氨基聚乙二醇(PEG-NH₂),并以此作为引发剂,引发NCA开环聚合.合成了不同组成和分子量的聚L-丙氨酸-聚乙二醇(PLAA-PEG-PLAA)嵌段共聚物.利用IR、¹H NMR、DSC、WAXD、CD等方法对共聚物结构进行了表征.结果表明,PEG-NH₂引发NCA开环聚合得到的是嵌段共聚物,通过¹H NMR谱得到共聚物组成及数均分子量;引入PEG的结果使聚L-丙氨酸的亲水性有所改善;CD测诚结果表明共聚物在水溶液中主链主要以α-螺旋构象存在.     

1,3-二(炔丙基氧)苯与4,4'-二叠氮甲基联苯的聚合反应及聚合物性能的研究

研究了1,3-二(炔丙基氧)苯(BPOB)与4,4'-二叠氮甲基联苯(DAMBP)的本体聚合行为. 核磁共振氢谱(¹H NMR)表征了聚合物的结构, 通过傅立叶红外技术(FT-IR)观察了反应过程中的基团变化情况, 采用差示扫描量热技术(DSC)研究了聚合反应动力学, 在较低温度(80 ℃)下二元叠氮与二元炔发生了1,3-偶极环加成聚合反应, 生成了主链含三唑环的聚合物; 利用Kissinger法和Crane法处理得到了反应的动力学参数: 反应级数为0.92, 反应活化能E_a为79.8 kJ• mol^－1, 频率因子A为1.26×10¹⁰ min^－1. 利用凝胶渗透色谱(GPC)、动态热机械分析(DMA)和热重分析方法(TGA)研究了聚合产物的性能. 结果表明, 聚合物的数均分子量达4.22×10⁴, 聚合物有较高的玻璃化转变温度和良好的热稳定性, 玻璃化转变温度达到131 ℃, 热分解温度(T_d5)达355 ℃     

预氧化聚铝碳硅烷纤维的热分解动力学及其机理

利用热重分析仪(TGA)对预氧化聚铝碳硅烷(PACS)纤维进行了热动力学研究, 用改良的Coats-Redfern法计算了动力学参数, 用Doyle法计算了理论失重值, 并根据FT-IR, XRD和SEM对其热分解的机理进行了分析. 结果表明, 在热分解反应的主要阶段, 预氧化纤维的反应活化能低于PACS纤维, 氧的引入有利于纤维的热分解; 快速升温有利于预氧化PACS纤维的热分解. 在初始分解阶段, 主要为低分子量的PACS和H₂O的逸出, 同时≡Si—H键之间以及≡Si—H与≡Si—CH₃键发生了脱氢、脱CH₄反应, 从而导致交联程度的增加; 随热分解温度进一步的提高, 分子的有机侧基急剧热解, 分解产物从有机物转变为存在部分微晶的无机结构; 热分解温度继续提高, 纤维结构进一步完善, 1300 ℃左右, β-SiC晶粒大小约为2～4 nm左右, 纤维具有较好的性能.     

聚[(甲氧基乙氧基乙氧基)1.0(乙氧基吡咯烷酮)1.0]膦腈的合成及性能研究

用三氯化铝催化六氯三聚膦腈开环聚合制得线性聚二氯膦腈(PDCP), 通过PDCP磷原子上的亲核取代反应, 合成了新的水溶性高分子聚[(甲氧基乙氧基乙氧基)_1.0(乙氧基吡咯烷酮)_1.0]膦腈(P3), 用³¹P NMR, ¹H NMR, ¹³C NMR和IR对其结构进行了确证, 用DSC测定了其玻璃化转变温度T_g和熔融温度T_m, 用蒸汽压渗透法(VPO)测定了其数均分子量. 改进了聚二(乙氧基吡咯烷酮)膦腈(P2)的合成方法. 体外降解实验表明, P3具有和P2类似的pH响应性降解行为, 降解速率在pH=5.0时最快, 而在pH=7.4和8.0时较慢. P3在所测试的3个pH缓冲溶液中均比P2降解慢. 用³¹P NMR、薄层色谱(TLC)和滴定法对降解产物进行了检测, 初步推断了P3在不同pH介质中的水解机理, 其在pH=5.0的缓冲溶液中的降解, 除侧链断裂外, 聚膦腈的骨架也裂解; 而在pH=7.4和8.0时的降解仅为侧链的断裂. 用噻唑蓝(MTT)比色法进行的体外细胞毒性评价实验表明, P3及其在pH=5.0的缓冲溶液中降解49 d后的产物均对细胞表现出了很好的生物相容性, 而且其降解产物在浓度为800 μg/mL时还表现出一定的促进细胞增殖作用.     

聚苯乙烯-co-聚(2,3,4,5,6-五氟苯乙烯)共聚物: 合成及其多孔薄膜的制备

利用原子转移自由基聚合(ATRP)方法, 分别在三氟甲苯、含氟离子液体以及三氟甲苯/含氟离子液体混合溶剂体系中合成了聚苯乙烯-co-聚(2,3,4,5,6-五氟苯乙烯)(PS-co-PPFS)共聚物, 通过¹H NMR、¹⁹F NMR、元素分析以及凝胶渗透色谱法(GPC)对所得聚合物的分子链结构和组成进行了分析和表征. 随后, 利用静态呼吸图法分别在CS₂, CHCl₃ 和CH₂Cl₂ 中制备了有序多孔薄膜, 用扫描电子显微镜(SEM)观察其表面形貌, 并与利用分子量大小相当的聚苯乙烯均聚物(PS)制备的多孔薄膜进行了对比. 研究结果表明: 在三氟甲苯和含氟离子液体溶剂体系中, 均可利用ATRP 聚合方法获得窄分子量分布的PS-co-PPFS 共聚物(M_n＝5200～7900 g·mol^-1, i>M_w/M_n＝1.12～1.22). 对聚合物薄膜的扫描电子显微镜(SEM)观察和分析显示: 分别以CS₂, CHCl₃ 和CH₂Cl₂ 作为溶剂, 利用静态呼吸图法均可制备出PS-co-PPFS 共聚物多孔薄膜. 然而, 与在CHCl₃ 和CH₂Cl₂ 中制备的PS 均聚物多孔薄膜的表面形貌不同的是, PS-co-PPFS 共聚物多孔薄膜呈现出无序排列、平均孔径大小不同的两种孔结构; 在CHCl₃ 中制备所得薄膜的孔结构有序性相对较好, 两种孔的平均孔径分别为0.75 和0.37 μm.     

铁酸镍用于热化学循环反应CO2分解制CO的研究

采用共沉淀法制备了NiFe₂O₄和NiFe₂O₄/ZrO₂催化剂,用TGA考察了其热化学法,CO₂高温分解反应性能。通过对反应前后催化剂的表征发现,反应高温使两种催化剂都发生了明显的烧结,导致在热还原反应中形成的还原态氧化物不能完全被CO₂氧化从而降低了催化剂的反应性能;ZrO₂的加入对于提高催化剂的热稳定性以及循环反应稳定性具有重要的作用。在高温反应炉中考察了NiFe₂O₄/ZrO₂的CO₂分解实验,结果表明,提高热还原温度可以提高CO产量,然而,随着循环次数的增加CO的产量降低得更明显。     

三种不同碳桥联双核茂钛配合物的合成及催化乙烯聚合研究

合成了3种不同结构的CnH₂n桥联双核茂钛配合物(CH₃)₂C[(C₅H₄)TiCl₂(C₅H₅)]₂(3),(CH₂)_n[(C₅H₄)TiCl₂(C₅H₅)]₂(6,n=3;7,n=4),并用1HNMR进行了表征.发现以甲苯为溶剂时,不仅提高了产率,而且有效地避免了副产物Cp₂TiCl₂的生成.研究了化合物7/MAO(甲基铝氧烷)催化乙烯聚合的反应,考察了反应条件对催化体系的影响.结果表明,催化活性随着n(Al)/n(Cat.)比的增大而提高,聚乙烯的分子量在n(Al)/n(Cat.)=500和50℃时达到最高值9.0102×10⁴;随着聚合时间的延长,催化活性下降,而产物分子量不断升高;随着温度的上升,50℃时催化活性和聚乙烯的分子量最高,分别为2.4074×10⁵gPE/(molTi·h)和6.8679×10⁴.随着桥联双核茂钛配合物碳桥的增长,催化活性增加,所得聚乙烯的分子量降低.     

"一锅法"N-(2-苯甲酰胺苯基)-水杨醛亚胺/TiCl4·2THF催化乙烯聚合

报道了4个含苯甲酰胺取代的水杨醛亚胺配体: N-(2-苯甲酰胺苯基)-水杨醛亚胺(L1)、 N-(2-苯甲酰胺苯基)-3-甲基水杨醛亚胺(L2)、 N-(2-苯甲酰胺苯基)-3-叔丁基水杨醛亚胺(L3)和N-(2-苯甲酰胺苯基)-3,5-二溴水杨醛亚胺(L4)的合成, 采用 ¹H NMR和HRMS对其结构进行了表征. 在助催化剂甲基铝氧烷(MAO)作用下, 以L3与TiCl₄·2THF为模型催化体系, 在最佳陈化条件(陈化温度为25 ℃, 陈化时间为30 min, 配体与TiCl₄·2THF的摩尔比3∶1)下, 考察了L1~L4/TiCl₄·2THF催化体系Al/Ti摩尔比、 反应时间、 反应温度和聚合压力, 以及配体结构等对乙烯聚合的影响. 结果表明, 随着在水杨醛骨架上氧原子邻位取代基位阻的增大, 催化体系的活性及所得聚乙烯的分子量均有增加, 其中以L3的催化活性最高, 达到224 kg PE/(mol Ti?h). 采用高温 ¹H NMR, ¹³C NMR, GPC-IR和DSC等对由不同配体L1~L4/TiCl₄·2THF得到的聚乙烯样品的微观结构与热性能进行了分析与表征, 结果显示样品为线性高密度聚乙烯, M_n=5.9×10 ⁴~11.9×10 ⁴, 分子量分布(PDI)为21.9~72.1.     

Tabletting of solid dispersion particles consisting of indomethacin and porous silica particles

We attempted to make the rapidly dissolving tablet (Tab) containing solid dispersion particles (SD) with indomethacin (IMC) and porous silica (Sylysia350) as carrier prepared by using spray-drying technique. Rapidly dissolving tablet was formulated with mannitol as a diluent and low substituted hydroxypropylcellulose (L-HPC) or partly pre-gelatinized starch (PCS) as a disintegrant. The percent dissolved from Tab (SD) was higher than that of tablet containing physical mixture (PM) at 20 min. Nearly 100% of drug in Tab (SD) was dissolved within 60 min, while the drug dissolution of Tab (PM) was not completed at the same time period. In addition, the tensile strength of Tab (SD) was much higher than that of Tab (PM). Adding L-HPC in Tab (SD) (Tab (SD-L-HPC)), the percent dissolved from Tab (SD-L-HPC) at 5 min became much higher than that from Tab (SD). The dissolution profile of IMC from Tab (SD-L-HPC) was almost the same irrespective of the compression pressure, while the tensile strength of tablet increased with increasing the compression pressure. In comparing the compaction property of these tablets by observing the ratio of residual die wall pressure (RDP) to maximum die wall pressure (MDP) (RDP/MDP), it was found that addition of L-HPC in the tablet formulation improved compactibility. In case that PCS was formulated as disintegrant, Tab (SD-PCS), similar improvement in the dissolution profile and tensile strength was observed, though the dissolution rate of IMC from Tab (SD-PCS) was slightly lower than that from Tab (SD-L-HPC) irrespective of the compression pressure.     

磷酸酯阻燃剂HDP的合成工艺及其在ABS中的阻燃作用

采用新工艺路线合成高熔点磷酸酯阻燃剂———对苯二酚双(二苯基磷酸酯)(HDP).首先采用对苯二酚和三氯氧磷合成中间产物,再将中间产物与苯酚反应,经分离纯化得到产品HDP,收率达到90%以上,常温下为白色固体.采用傅里叶红外光谱、氢谱、磷谱和质谱测试确定了其结构.同时,研究了HDP的阻燃性,并与间苯二酚双(二苯基磷酸酯)(RDP)进行了比较,研究发现当HDP和RDP分别与成炭剂酚醛树脂(NP)按20/10比例添加到丙烯腈-丁二烯-苯乙烯(ABS)树脂中,增强了复合材料凝聚相阻燃作用,极限氧指数(LOI)有所提高.通过热重及锥形量热分析两种复合材料以及各种组分的热降解过程,阻燃剂的添加对ABS树脂的热稳定性和残炭量明显提高,而且ABS/HDP/NP复合材料的抑烟性更好;同时采用扫描电镜(SEM)和X射线能量色散谱(EDS),发现ABS/HDP/NP复合材料燃烧后成炭空隙均匀,其残炭中磷分布比ABS/RDP/NP复合材料残炭中的磷分布更加均匀.研究表明,HDP与NP互配添加到ABS中,在凝聚相阻燃作用优于RDP.     

The impact of resorcinol bis(diphenyl phosphate) and poly(phenylene ether) on flame retardancy of PC/PBT blends

Flame retardancy of bisphenol A polycarbonate (PC)/poly(butylene terephthalate) (PBT) blends was improved by the addition of resorcinol bis(diphenyl phosphate) (RDP) and poly(phenylene ether) (PPO). A PC/PBT blend at 70/30 weight ratio obtained a V‐0 rating by the addition of 10 wt% RDP and 10 wt% PPO. The combination of 5 wt% methyl methacrylate‐butadiene‐styrene tercopolymer (MBS) with 3 wt% ethylene‐butylacrylate‐glycidyl methacrylate tercopolymer (PTW) causes a remarkable increase in toughness of the PC/PBT/RDP blend while maintaining a high rigidity. A detailed investigation of the flame‐retardant action of PC/PBT/RDP and PC/PBT/RDP/PPO blends was performed using thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), TGA‐FTIR, temperature‐programmed pyrolysis/gas chromatography/mass spectrometry (TPPy/GC/MS), and scanning electron microscopy/energy dispersive spectrometer (SEM/EDS). The results demonstrate that RDP induces a higher char yield at ca. 450 °C and synchronously increases the thermal stability of the blend with PPO. The flame‐retardant role of RDP in the condensed phase was discerned from TGA, FTIR, and SEM/EDS of the residues. Copyright © 2010 John Wiley & Sons, Ltd.     

8—Hydroxyguanine,A Product From Damaged DNA Can Be Used in the DNA Salvage Pathways

The metabolic mechanism of 8-hydroxyguanine (8-OHGua)is so far unknown,however it is known to function in the mutagenic events in biological systems.In the present study,the metabolic processes is ivvestigated by the reaction of 8-OHGua with PRPP catalyzed by HGPRT and Mg(Ⅱ）.The evidence shows that the interaction between 8-OHGua and the enzyme is indeed taken place and 8-OHGMP is formed.     

Fire retardancy mechanisms of arylphosphates in polycarbonate (PC) and PC/acrylonitrile-butadiene-styrene

The pyrolysis of polycarbonate (PC) and PC/acrylonitrile-butadiene-styrene (PC/ABS) with and without arylphosphates (triphenylphosphate TPP, resorcinol-bis(diphenyl phosphate) RDP and bisphenol A bis(diphenyl phosphate) BDP) is investigated by thermal analysis as key to understanding the flame retardancy mechanisms and corresponding structure–property relationships. The correspondence between the decomposition temperature range of arylphosphates and PC is pointed out as prerequisite for the occurrence of the reaction between arylphosphate and structures that are typical for the beginning of PC decomposition. Resulting cross-linking enhances charring in the condensed phase and competes with the alternative release of phosphate in the gas phase and thus flame inhibition. Flame inhibition was identified as the main flame retardancy mechanism. The additional condensed phase mechanisms optimise the performance.     

Ultrasensitive detection of phenolic compounds based on a spin-labeled luminescent lanthanide complex

Herein we propose a novel method for ultrasensitive detection of phenolic compounds. This method was developed based on a spin-labeled terbium complex Tb(3+)/cs124-DTPA-TEMPO (1). This spin-labeled terbium complex is a weakly luminescent compound and shows strong off-on luminescent response to phenolic compounds in the presence of horseradish peroxidase (HRP), glutathione (GSH) and hydrogen peroxide. The analyte recognition and signaling mechanism are discussed and the factors affecting the off-on luminescence have been explored. Detection limits of 1.1 nM for phenol, 1.1 nM for resorcine, 0.6 nM for m-cresol, 3 nM for p-cresol, and 0.5 nM for 2,4-dichlorophenol were obtained, respectively. The practicability of the proposed method has been tested in detection of the concentration of spiked nearshore seawaters, and recoveries of 77.4-80.4% with relative standard deviations (RSDs) of 1.0-2.2% were obtained.     

Differential Distortion of Purine Substrates by Human and Plasmodium falciparum Hypoxanthine‐Guanine Phosphoribosyltransferase to Catalyse the Formation of Mononucleotides

Plasmodium falciparum (Pf) hypoxanthine‐guanine phosphoribosyltransferase (HGPRT) is a potential therapeutic target. Compared to structurally homologous human enzymes, it has expanded substrate specificity. In this study, 9‐deazapurines are used as in situ probes of the active sites of human and Pf HGPRTs. Through the use of these probes it is found that non‐covalent interactions stabilise the pre‐transition state of the HGPRT‐catalysed reaction. Vibrational spectra reveal that the bound substrates are extensively distorted, the carbonyl bond of nucleobase moiety is weakened and the substrate is destabilised along the reaction coordinate. Raman shifts of the human and Pf enzymes are used to quantify the differing degrees of hydrogen bonding in the homologues. A decreased Raman cross‐section in enzyme‐bound 9‐deazaguanine (9DAG) shows that the phenylalanine residue (Phe186 in human and Phe197 in Pf) of HGPRT stacks with the nucleobase. Differential loss of the Raman cross‐section suggests that the active site is more compact in human HGPRT as compared to the Pf enzyme, and is more so in the phosphoribosyl pyrophosphate (PRPP) complex 9DAG–PRPP–HGPRT than in 9‐deazahypoxanthine (9DAH)–PRPP–HGPRT.     

Electrochemical synthesis of silver nanoparticles in solution

Silver nanoparticles in the bulk solution were obtained by the potentiostatic electrolysis in undivided cell using silver anode at the potential of the mediator reduction (tetraviologen calix[4]resorcine) at room temperature in DMF/0.1 M Bu₄NPF₆ media. The metal nanoparticles aggregate to form larger particles eventually.     

New Total Synthesis of O‐Methyledgeworin and Edgeworin

Upon thermal condensation of diethyl (coumarinyl‐7‐oxy)malonate with O‐methyl‐resorcine, the corresponding bis[coumarinyl]ether, 4‐hydroxy‐O‐methyledgeworin is obtained in good yield. This leads to 4‐bromo‐O‐methyledgeworin, O‐methyledgeworin, and edgeworin.     

CoAPSO—5分子筛的合成与性能

用水热晶化法合成了ＣｏＡＰＳＯ－５分子筛,用Ｘ射线衍射,电子探针,红外光谱以及吸附吡啶的红外光谱等方法对其结构和表面性质进行了研究,并用甲苯甲醇烷基化反应考察了其催化性能,结果表明,ＣｏＡＰＳＯ－５为中强酸性分子筛,具有较高的甲苯甲醇烷基化活性和对二甲苯选择性,对二苯收率高于２０％,且烷基化活性和对二甲茉选择性出现了“同向效应”。