退火过程中聚乳酸中间相的形成和结构演化

采用淬火法制备聚乳酸(PLA)非晶薄膜,并利用原位显微红外光谱在线研究PLA非晶薄膜在不同退火温度下的结构演化.结果表明,PLA非晶薄膜存在一个临界结晶温度,当退火温度高于临界结晶温度时,PLA非晶薄膜可以通过分子链的局部调整实现冷结晶,反之,不能发生冷结晶;在冷结晶过程中先出现中间相,随后发生中间相-晶体相的转变;中间相是通过分子链的构象调整和分子链间的堆砌调整产生的,退火温度越高,中间相出现得越早,最终得到的晶体结构越规整.     

乙烯共聚单体对双轴拉伸聚丙烯薄膜用树脂的结晶及拉伸性能的影响

采用热分析、光学显微镜、拉伸测试与广角X-射线衍射等方法研究了双轴拉伸聚丙烯薄膜用均聚聚丙烯(h-BOPP)与含有少量乙烯单体的共聚聚丙烯(c-BOPP)材料的熔融、结晶特性和拉伸性能.研究发现,与均聚样品相比,共聚样品的等规度低,结晶速率慢,在相同的结晶温度条件下,其半结晶时间较长.退火处理后,结晶完善程度增加,均聚和共聚样品的断裂伸长率均比其未退火处理的低.但共聚样品的结晶速率慢,经过退火处理后其结晶完善性稍低于均聚样品,所以其断裂伸长率略大于均聚样品.经过拉伸形变后,样品的结晶结构被部分破坏,取向的非晶的分子链在后续的升温过程中很容易重构为更加完善的结晶结构,由于分子链结构的差异,均聚样品的结晶重构能力更强.阐释了由于链结构的不同导致的BOPP拉伸性能和结晶性能差异的机理.     

快速增压制备非晶聚乳酸的等温冷结晶行为研究

通过快速增压法(RC)和自然冷却法(CN)分别制备出完全非晶的聚乳酸(PLA)样品,利用差示扫描量热仪(DSC)、偏光显微红外光谱仪(FTIR)和广角X-ray(WAXD)研究了2种非晶样品的初始结构、不同结晶温度下的等温冷结晶行为及最终的微观结构.结果表明,在温度为110、115、125、130、135及140℃下等温结晶时,RC样品的结晶速率明显高于CN样品;WAXD数据显示,结晶完成后RC样品的结晶度明显高于CN样品,但两者最终的晶粒尺寸大小相近,说明RC样品结晶过程中具有较高的成核密度;实验发现,PLA熔体在快速增压过程中很可能形成了某些类似物理老化样品中存在的局部有序结构,这些局部有序结构促进了晶核的形成,使冷结晶速率明显加快,结晶度提高.     

热处理对尼龙6及其与聚酰胺嵌段共聚物共混体系晶体熔融行为和结晶结构的影响

采用溶液共混-共沉淀的办法获得尼龙6及聚酰胺嵌段共聚物/尼龙6共混体系粉末,样品在260℃下熔融之后经程序降温的方法得到非淬火样品,然后分别在190℃下高温退火不同时间(0~48 h),采用示差扫描量热仪(DSC)、广角X射线衍射仪(WAXD)、偏光显微镜(POM)等表征手段研究热处理对体系晶体熔融行为和结晶结构的影响.结果表明,(1)在相同的热历史条件下,嵌段共聚物的存在影响了尼龙6的结晶行为及结晶结构;(2)退火处理对两种样品有着不同的影响,对于尼龙6体系,退火处理促进了非晶相向晶相的转变,大大提高样品的结晶完善程度和结晶度;对于共混体系,退火处理同样促进了非晶相向晶相的转变,同时形成新的α型和γ型结晶,体系的结晶完善程度明显提高,退火48 h后,结晶度比原始样品提高约84%.     

热历史对尼龙1212熔融行为的影响

利用DSC方法研究了不同热历史条件对尼龙1212熔融行为的影响.不同的热历史条件下,在DSC曲线上,观察到尼龙1212产生2个或3个熔融峰,依据聚合物结晶理论,对各峰的来源进行了分析.在160℃下不同温度退火120 min的尼龙1212样品DSC曲线上,低温结晶熔融峰主要由低温结晶形成的一些微晶体或者片晶熔融产生,其晶体完善程度较差,熔融峰值较低,峰面积较小;主熔融峰是由样品在淬火过程中形成的晶体和升温过程中低温结晶形成的晶体的熔融重结晶形成较为完善的晶体熔融所产生,熔融峰值较高,峰面积较大.在不同的升温速率条件下,熔融峰温度有所移动,表明不同升温速率条件下产生的熔融峰的结晶晶型是相同的.在不同结晶时间下结晶,延长结晶时间对较高完善程度晶体的生长有利.在不同温度下依次退火处理的样品,熔融产生两个附加峰,这两个附加峰的峰温都比它们相应的退火温度高,而峰高和峰面积随退火温度降低而减小.根据等温结晶结果,由Hoffman方法确定了尼龙1212的平衡熔融温度为202.8℃.     

超速升温对玻璃态聚偏氟乙烯结晶的影响

我们曾研究超速淬火温度对聚偏氟乙烯(PVF_2)薄膜结晶结构的影响,在不同温度下淬火可分别得到α、β和γ三种晶型结构。本工作从非晶的玻璃态PVF_2出发,通过超速升温的方法,进一步研究结晶温度对PVF_2晶型结构的影响。     

拉伸对聚左旋乳酸结晶的影响

在成型加工过程中,拉伸是提高聚合物材料结晶能力的一种重要手段. 本文采用红外光谱、差示扫描量热分析、X射线衍射等方法系统研究了不同温度下拉伸对聚左旋乳酸（PLLA）结晶行为的影响. 结果表明,在合适的温度条件下,拉伸能迅速提高PLLA的结晶速度和结晶度. 对经过拉伸预处理但未结晶的PLLA样品进行等温及非等温结晶的研究发现,经过拉伸预处理的PLLA样品的结晶速率和结晶度都得到提高,这表明预拉伸会影响PLLA在后续过程中的结晶行为.     

静电粉末喷涂法制备不同熔融指数聚醚醚酮涂层的机械和摩擦学性能

通过静电粉末喷涂法在不锈钢基材上制备了不同熔融指数的聚醚醚酮(PEEK)涂层.熔融涂层在冰水混合物中淬火得到无定形涂层,将无定形涂层在260℃退火处理30 min得到半结晶涂层.X射线衍射(XRD)测试结果表明,退火处理使不同熔融指数的PEEK涂层从开始的无定形结构转变成为半结晶结构.PEEK涂层的硬度和摩擦学性能研究结果表明,在相同条件下结晶处理,PEEK熔融指数越大,结晶度越高.与无定形涂层相比,不同熔融指数PEEK的半结晶涂层的硬度更高,摩擦系数和磨损率更低.熔融指数较大的PEEK-B和PEEK-C均能形成平整的涂层,摩擦系数和磨损率稳定,熔融指数对其影响不大.半结晶涂层B和C的摩擦系数低至0.15以下,磨损率低至20×10-6mm3/(N·m)以下,更适合静电喷涂制备PEEK涂层.     

涤纶薄膜拉伸过程中的电镜研究

<正> 聚对苯二甲酸乙二酯(PET)是用于纤维和薄膜的最重要的高分子材料之一。在拉伸过程中拉伸温度、拉伸比、应变速率等不同因素对PET的结晶、取向以及所形成的织态等的影响已有过广泛的研究。但用电镜直接观察PET薄膜在不同拉伸条件下的高分子聚集态结构的变化则报道很少。我们选择丙烯胺作刻蚀剂处理拉伸方式、拉伸温度、应变速率和拉伸比不同的PET试样,用扫描电镜直接观察其形态的变化。     

含氟聚合物共混对聚醚醚酮结晶行为的影响

通过示差扫描量热仪(DSC)对含氟聚合物与聚醚醚酮(PEEK)共混物的非等温结晶熔融行为和等温结晶熔融行为进行了研究.研究表明:不同的含氟聚合物以及具有不同端基的同种含氟聚合物对PEEK的结晶行为有不同的影响.端基为酰氟(COF)的乙烯-四氟乙烯共聚物(ETFE)能促进PEEK结晶时的成核,加快PEEK的等温结晶速率,而聚四氟乙烯(PTFE)则会减慢PEEK的等温结晶速率.     

FTIR Spectroscopic Study of Crystallization of Uniaxial Drawn Syndiotactic Polystyrene/Carbon Nanotube Nanocomposite Films

The crystallization of uniaxial hot drawn syndiotactic polystyrene/multi-walled carbon nanotube (sPS/MWCNT) nanocomposite films was studied by FTIR spectroscopy. The effects of MWCNT content, draw ratio and drawing temperature on the sPS crystallinity were investigated. The sPS/MWCMT nanocomposite films show reduced crystallinities with the increase of MWCNT content. In addition, with the increase of draw ratio, both the pure sPS and the sPS/MWCNT nanocomposite drawn films exhibit increased crystallinity. The effect of drawing temperature on the sPS crystallization is complex. In a temperature range of 100―135 ℃, the crystallinity decreases with drawing temperature, whereas it increases at 140 ℃ for both pure sPS and its nanocomposite films.     

尼龙1010的拉伸结晶行为及Brill转变

摘要 :本文通过示差扫描热分析,广角X射线衍射分析及二维广角X射线散射等手段研究和讨论了尼龙1010在不同的拉伸比率(λ)及拉伸温度（Td）下拉伸诱导的晶体转变及结晶取向行为。实验表明,在拉伸条件下,尼龙1010易于从α晶型向δˊ晶型转变,而拉伸比率的提高,有利于促进这种Brill转变。而在相同的拉伸比率下,随着拉伸温度的提高,发现了尼龙1010从δˊ晶型向α晶型的独特转变,而这种过程刚好与无拉伸状态下的尼龙1010晶型和温度的相互关系截然相反。二维广角X射线散射实验研究结果表明尼龙1010的晶体取向度主要和拉伸比有关,并且（002）的晶面间距随着拉伸比率的提高而增大,表明了长轴尺寸的增大对拉伸取向的依赖关系。     

不同后处理条件下聚萘二甲酸乙二酯纤维的结构变化

对不同纺速下制得的聚萘二甲酸乙二酯 (PEN)初生纤维进行了冷拉伸、定长热处理和热拉伸等后处理 .通过WAXS、DSC等测试研究了纤维中结构变化与后处理条件之间的关系 .结果表明 ,较低纺速下所制得的无定形初生纤维在低于Tg 温度下的冷拉伸时发生了应力诱导结晶 ,纤维中生成了α晶体 .同样的初生纤维在定长热处理过程中直至 2 0 0℃仍保持无定形结构 .这些结果说明施加应力相对于升高温度对于α晶体的生成更为重要 .而热拉伸样品中结晶结构的形成与初生纤维的结构有很大关系 ,低纺速下无定形初生纤维在热拉伸后形成α晶体 ,而高纺速下主要含有 β晶体的初生纤维经热拉伸后 β晶体会部分转变为α晶体 ,且 β晶转变为α晶的难易程度取决于初生纤维中 β晶的完善程度 ,初生纤维中 β晶越完善 ,热拉伸时 β晶体越不易转变为α晶体     

聚乙烯基环己烷-聚乙烯-聚乙烯基环己烷三嵌段共聚物溶液的受限结晶研究

嵌段共聚物由于组分间的化学不相容性而发生微相分离,组装成各种有序的纳米结构,如球、圆柱、层及双连续结构等．半晶型嵌段共聚物由于引入了能结晶的组分,使体系中存在两种相互竞争的过程,即微相分离与结晶,所以能形成更为丰富的有序结构．聚乙烯基环己烷-聚乙烯-聚乙烯基环己烷[Poly(Vinylcyclohexane)-b-poly(ethylene)-b-poly(vinylcyclohexane),     

Structure development and physical properties achieved in the drawing and/or annealing of PEN fibers

As‐spun poly(ethylene‐2,6‐naphthalate) (PEN) fibers (i.e., precursors) prepared from high molecular weight polymer were drawn and/or annealed under various conditions. Structure and property variations taking place during the treatment process were followed via wide‐angle X‐ray scattering (WAXS), small‐angle X‐ray scattering, differential scanning calorimetry (DSC), and mechanical testing. Both the WAXS and DSC measurements of the cold‐drawn samples stretched from a low‐speed‐spun amorphous fiber indicate that strain‐induced crystallization can occur at a temperature below the glass‐transition temperature and that the resultant crystal is in the α‐form modification. In contrast, when the same precursor was subjected to constrained annealing, its amorphous characteristics remained unchanged even though the annealing was performed at 200 °C. These results may imply that the application of stretching stress is more important than elevated temperatures in producing α‐form crystallization. The crystalline structure of the hot‐drawn samples depends significantly on the morphology of the precursor fibers. When the precursor was wound at a very low speed and in a predominantly amorphous state, hot drawing induced the formation of crystals that were apparently pure α‐form modification. For the β‐form crystallized precursors wound at higher speeds, a partial crystalline transition from the β form to the α form was observed during the hot drawing. In contrast with the mechanical properties of the as‐spun fibers, those of the hot‐drawn products are not improved remarkably because the draw ratio is extremely limited for most as‐spun fibers in which an oriented crystalline structure has already formed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1424–1435, 2000     

拉伸温度对α’-型聚乳酸结构与性能的影响

α’-晶型聚乳酸(PLA)膜被制备和单轴拉伸.通过凝胶渗透色谱仪(GPC)、全反射红外光谱(ATR-IR)、差示扫描量热仪(DSC),X射线衍射(XRD)及Raman光谱等测试技术研究了拉伸温度梯度变化对α’-晶型PLA膜的分子量及其分布、分子链构象、结晶度、晶型转变和取向行为的影响.在恒定拉伸速度与应变下,拉伸温度对PLA膜的应力-应变曲线,特别是屈服强度、拉伸模量产生了较大的影响,其值随拉伸温度的增加而降低.GPC测试结果表明,在不同的温度下拉伸后,PLA会发生一定程度的降解,分子量降低;ATR-IR,XRD,DSC和Raman光谱测试结果表明,在不同的温度下拉伸后α’-型PLA没有发生晶型的转变,即没有由α’-晶体转变为α-或β-晶体.结果表明PLA的结晶度、分子链取向程度强烈依赖于拉伸温度:当拉伸温度低于100℃时,α’-型PLA膜的结晶度与沿着拉伸方向的变形程度随拉伸温度的增加而增加,分子链的高度取向诱导了PLA结晶;当拉伸温度超过100℃后,PLA的分子链沿着拉伸方向上的有序度与结晶度将降低.     

Fourier-transform infrared study of coextrusion-drawn poly(ethylene terephthalate)

The effects of initial morphology and extrusion temperature on the orientational anisotropy and conformational changes on coextrusion drawing of poly(ethylene terephthalate) (PET) have been determined by Fourier-transform polarized infrared spectroscopy. The samples were drawn from both amorphous and semicrystalline (50%) PET at 50 and 90°C. A strong influence of coextrusion drawing temperature was observed for overall chain orientation evaluated from the dichroic ratio of the 795-cm^?1 band for the samples prepared from the amorphous state: this dependence was less prominent in samples drawn from the semicrystalline state. Under the same drawing conditions, the dichroic ratio for the 973-cm^?1 trans band for samples prepared from the amorphous state was higher than from the semicrystalline state. Furthermore, in all samples, the relative intensity of this band was almost proportional to the degree of crystallinity. In all samples, the gauche content, evaluated from the 896-cm^?1 band, decreased with increasing draw ratio. However, the dichroic ratio of this band was near unity regardless of draw ratio, initial morphology, or extrusion temperature. From these results it is considered that all gauche units in the amorphous phase are almost isotropic in the extrusion-drawn samples with overall orientation arising largely from the crystalline chains possessing totally the trans conformation (973 cm^?1) in its content. In order to evaluate the deformation mechanism of the coextrusion drawing method, the relationship between the bulk and film surface orientation is also reported.     

Solid-state coextrusion of poly(ethylene terephthalate). II. Drawing of semicrystalline PET

The drawing of semicrystalline (33 and 50%) poly(ethylene terephthalate) (PET) films has been studied by solid-state coextrusion. Because of its brittleness and opacity, isotropic and semicrystalline PET film is of little practical use. Early attempts to cold-draw crystalline films led to fracture in contrast to deformation of amorphous PET. However, we have succeeded in systematically preparing films with extrusion draw ratios ≤4.4 from semicrystalline PET. In many cases, the properties of the drawn extrudates, as a function of extrusion temperature T_ext and extrusion draw ratio EDR, were similar to those prepared from amorphous PET. However, some remarkable differences have also been found. In the case of coextrudates prepared from isotropic 50% crystalline PET, we found that the larger the deformation, the lower the apparent resulting crystallinity. In the extreme, a 34% reduction in crystallinity after deformation was observed. For the coextrudates drawn from initially 33% crystalline PET, slightly different behavior occurred. For T_ext ≤ 90°C, all extrudates showed crystallinities lower than the original isotropic film, with a minimum at EDR = 3; for T_ext ≥ 110°C, crystallinities were slightly greater than in the original film and increased with EDR. Qualitative measurements of heats of fusion were in agreement with density gradient results for PET crystallinity. In contrast is our previous finding that extrudates from initially amorphous PET always increase in crystallinity with EDR, because of stress-induced crystallization. The results now suggest that in the T_ext range investigated, the initial spherulitic structure is at least in part destroyed on drawing. In addition, the percent crystallinity is revealed to be dependent on T_ext, with lower values at lower temperatures. Mechanical tests show that the extrudates are similar or sometimes higher in tensile modulus when compared to amorphous PET drawn under the same conditions.     

Tensile drawing,morphology, and mechanical properties of poly(butylene terephthalate)

The concept of the drawing of a molecular network has been employed to derive a total network draw ratio from the combination of the two deformations occurring in the production of poly(butylene terephthalate), PBT, fibers by the consecutive processes of melt spinning and cold drawing. The mechanical properties of PBT can then be more readily explained in terms of increases in this total network draw ratio. However, the preorientation and crystallization that occurs in the melt-spinning process can occur at different strain rates and temperatures, depending on the wind up speed employed, on the extensional viscosity of the polymer, and on the variation of the extensional viscosity with temperature. Therefore, for polymers such as poly(butylene terephthalate), which can exist in two crystalline forms, the morphology of the final drawn fiber might be expected to depend on the first melt-spinning stage of the process as well as on the total network draw ratio. In this work, density, birefringence, mechanical measurements, and WAXD measurements, which have been made on the melt-spun fibers and on the drawn fibers, are described. Small differences in some of the drawn yarn mechanical properties at the same overall network draw ratio are related to the crystallinity and in particular to differences in the proportion of the α and β phases present in the drawn yarn. These in turn are related to differences in the temperature and stress during melt spinning and drawing. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2465–2481, 1997     

New technique of processing highly oriented poly(vinylidene fluoride) films exclusively in the β phase

Oriented β‐phase films were obtained by utilizing two different techniques: conventional uniaxial drawing at 80 °C of predominantly α‐phase films, and by drawing almost exclusively β‐phase films obtained by crystallization at 60 °C from dimethylformamide (DMF) solution with subsequent pressing. Wide angle X‐ray diffraction (WAXD) and pole figure plots showed that with the conventional drawing technique films oriented at a ratio (R) of 5 still contained about 20% of phase α, a crystallinity degree of 40% and β‐phase crystallographic c ‐axis orientation factor of 0.655. Drawing at 90 °C and with R = 4 of originally β‐phase films results in exclusively β‐phase films with crystallinity degree of 45% and orientation factor of 0.885. Crystalline phase, crystallinity degree, and crystallographic c‐axis orientation factor of both phases were also determined for α‐phase oriented films obtained by drawing α‐phase films at 140 °C. For films drawn at 140 °C the α to β phase transition drops to about 22%. Reduction in crystallinity degree with increasing R is more pronounced at draw temperature of 140 °C compared with 80 °C. Moreover, for both phases the c ‐axis orientation parallel to the draw direction is higher at draw temperature of 140 °C than at 80 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2793–2801, 2007