Al-MCM-41介孔分子筛催化对甲酚叔丁基化反应的研究

2-叔丁基对甲酚是一种有机中间体,在有机合成领域中占有重要地位,被广泛应用于表面活性剂、高档酚类抗氧化剂2246和2246-S、紫外线吸收剂UV-326等的生产[1]。特别是近十年来,以抗热老化为特征的功能性高档酚类抗氧化剂在国内外相继问世,它们对于提高聚合物材料的成型加工性能、     

吸附分离正构烃结焦失活的无粘结剂5A分子筛氧化再生研究

在固定床吸附器上模拟无粘结剂5A分子筛的失活过程,并对失活分子筛进行氧化再生研究。结果表明,焦炭会堵塞部分分子筛孔道,导致失活分子筛的比表面积和孔容减小、平均孔径增加。焦炭含量增加,分子筛的失活度增加,但增加的速率逐渐减小。氧化反应温度由582K升至787K,焦炭脱除率由64%增至100%。失活分子筛于787K下氧化处理后,其上焦炭被完全脱除,分子筛的吸附活性完全恢复。氧化再生后分子筛的比表面积和孔容增加,但难以恢复至新鲜分子筛的水平。在685K~884K,实验得到的无粘结剂5A分子筛上焦炭的氧化脱除宏观动力学方程为：ln(C₀/C) = 0.013exp(-28122.1/T) (p_O2)0.32t。     

Synthesis and crystal morphology control of AlPO4-5 molecular sieves by microwave irradiation

AlPO₄-5 molecular sieves have been synthesized by the hydrothermal and solvothermal reactions using triethylamine as a template, aluminum isopropoxide and orthophosphate as the aluminum and phosphorus resource under microwave irradiation. The influences of various experimental parameters, such as reaction time, reaction temperature and reaction power, have been systematically investigated. The morphology control of AlPO₄-5 molecular sieves was achieved by changing the dosage of solvent and HF to control the solvent polarity and control the nucleation respectively. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and so on. The results show that the aspect ratio of the AlPO₄-5 molecular sieves increases with the increase of the solvent polarity and with the increasing concentration of HF, the morphology of AlPO₄-5 molecular sieves changes from hexagonal plate to hexagonal rod.     

H NMR study of hydrogen bonding and molecular dynamics of 5CB confined to molecular sieves

It has been found that the main mechanism of ¹H protons spin–lattice relaxation of bulk 5CB at 200 MHz is its intramolecular motion, namely, the reorientation of CH₂ and CH₃ groups of its alkyl chain. Activation parameters of such motions have been estimated.

Drastic decrease in proton spin–lattice relaxation times at the nematic-to-isotropic phase transition can be explained by the activation of molecular translational diffusion and reorientations around long and short molecular axes of bulk 5CB.

Our NMR analysis revealed the slowing-down of molecular dynamics of confined 5CB molecules and their fragments. This can be explained by the interaction of some part of 5CB molecules with the surface active Si(Al)–OH centers of MCM matrix via hydrogen bonds of Si(Al)–OHN≡C-type.     

Effect of structural analogy between ZSM-5 and silicalite catalysts on the oxidative methylation of toluene with methane

Summary With ZSM-5 and silicalite (both initial and BaO modified) the yield of styrene, the most desirable reaction product, was highly represented when BaO modified silicalite was used as catalyst for the reaction. The catalytic results fitted the basicity, surface area and structural crystallinity.     

Basic zeolite and zeolite-type catalysts for the oxidative methylation of toluene with methane

The oxidative methylation of toluene with methane is used as a test reaction for determining the activity, selectivity and yield of C₈ hydrocarbons (ethylbenzene and styrene) over different zeolite and zeolite-type catalysts, viz., X, Y, mordenite, ZSM-5, silicalite and AlPO₄-5. Selectivity and basicity increase with decreasing Si/Al atomic ratio within the series of the same structural type. The basicity, surface structure and structural integrity are characterized by TPD of CO₂, XPS and IRS, respectively. This revised version was published online in June 2006 with corrections to the Cover Date.     

Carbon molecular sieves produced by the fixation of sulphur surface complexes

Summary A Saran carbon has been treated with carbon disulphide and sulphur in order to introduce sulphur surface complexes, a commercial activated carbon was also used. Samples obtained were characterized by their surface areas and porosities. The adsorption of n-hexane, benzene and cyclohexane has been measured out at high temperatures and under dynamic conditions using a gas chromatographic technique. Results were compared with those obtained when oxygen-surface complexes were introduced and it can be concluded that when CS₂ is used with a highly microporous carbon, such as Saran, a molecular sieve for cyclohexane (mean size 0.58 nm) is produced at determined amounts of sulphur fixed.     

原位合成负载型MSU系列分子筛

采用原位合成法,使用壬基酚聚氧乙烯醚(Tx-15)和脂肪醇聚氧乙烯醚(AEO-19)做为模板剂,在中性条件下合成W.MSU-1和W-MSU-2介孔分子筛,合成中使用乙酰丙酮(HAcac)作为助剂,考察其对介孔结构的影响,通过X射线衍射仪(XRD)、傅里叶红外光谱仪(FT-IR)、扫描电镜(SEM)、低温N2吸附对样品进行表征.结果表明,加入过渡金属氧化物有助于介孔的形成,助剂的使用提高了孔的结构参数.     

Oxidative coupling of methane over La-promoted CaO catalysts： Influence of precursors and catalyst preparation method

The oxidative coupling of methane to C2 hydrocarbons has been studied over a series of La-promoted CaO (La/Ca = 0.05) catalysts, prepared using different precursor salts for CaO and La2O3 (viz. acetates, carbonates, nitrates and hydroxides) and catalyst preparation methods (viz. physical mixing of precursors, co-precipitation using ammonium carbonate/sodium carbonate as a precipitating agent), under different reaction conditions (temperature: 700-850℃, CH4/O2 ratio: 4.0 and 8.0, and GHSV: 51360 cm3 g-1 h-1)...     

二甲醚催化转化制甲苯的反应研究

在氧气气氛中,对氧化钨改性的不同分子筛催化剂上二甲醚(DME)转化反应进行了评价。结果表明,WO3/HZSM-5催化剂上DME可以高选择性转化为甲苯,对其反应工艺条件进行了优化,常压、290℃、DME/O2比为2∶1时,二甲醚几乎完全转化,转化率为98.97%,甲苯的选择性达到39.71%。对催化剂结构和酸性进行表征,结果表明,ZSM-5分子筛的孔道结构最有利于甲苯的生成,WO3的介入调整了HZSM-5分子筛表面的酸性活性位点分布,在氧气气氛中有效地抑制了副产物的生成,使产物中甲苯的选择性提高。     

Stabilisation of reactive intermediates in molecular sieves

This paper presents studies on paramagnetic intermediates, free atoms and radicals produced in γ-irradiated molecular sieves and their reactions with adsorbate molecules or exchangeable cations. Four different systems have been investigated using EPR spectroscopy, Na-A/CH₄, AgNa-A/CH₃OH, Ag-SAPO-11/C₂H₄ and AgCs-rho/NH₃. It was found that methyl radicals are formed in two different sites in Na-A/CH₄ and in one of them they are stable at room temperature. The formation of Ag·CH₂OH⁺ radical cation with one-electron bond between silver and carbon has been established in AgNa-A/CH₃OH by EPR experiments with [¹³C]CH₃OH and DFT calculations. In Ag-SAPO-11/C₂H₄ the stabilisation of biligand silver/ethylene complex, Ag⁰(C₂H₄)₂ was postulated based on EPR and DFT results. Tetrameric silver clusters (Ag ₄ ³⁺ ) produced radiolytically in AgCs-rho/NH₃ strongly interact with two ammonia molecules as was deduced from the changes in superhyperfine structure of high-field EPR line of Ag ₄ ³⁺ pentet for zeolite exposed to [¹⁴N]NH₃ and [¹⁵N]NH₃. The presented examples clearly show that the combination of radiation methods with EPR technique is very useful to study the structure and reactivity of paramagnetic intermediates.     

Oxidative desulfurization of model diesel oil over Ti-containing molecular sieves using hydrogen peroxide

Three Ti-containing molecular sieves were studied in the oxidative desulfurization (ODS) of model diesel oil with hydrogen peroxide. Under optimal conditions, dibenzothiophene (DBT) conversion up to 80.6% and 42.6% could be obtained with Ti-HMS and Ti-MSU as catalysts, respectively. However, there is no activity in the sulfoxidation of DBT over TS-1. Effects of the TiO₂/SiO₂ ratio in Ti-HMS and reaction conditions, such as the reaction temperature, reaction time, n(H₂O₂)/n(S) on the sulfur removal were investigated.     

Mild benzhydrylation and tritylation of saccharidic hydroxyls promoted by acid washed molecular sieves

Commercially available 4 Å acid washed molecular sieves (AW 300 MS) promote the protection of primary and secondary saccharidic alcohols through a dehydration mechanism and in the absence of any strong protic or Lewis acid.     

载铜5A分子筛在汽油模拟体系中脱硫性能的研究

近年,美国环保局计划将汽油中硫的质量分数从当前的300×10-6降到2006年的30×10-6,欧盟也已经通过了新的汽油硫质量分数标准为30×10-6~50×10-6,德国甚至提出计划使用无硫汽油[1]。中国汽油硫的质量分数高达800×10-6以上,与世界汽油品质距离甚远。因此汽油中硫化物的脱除成为当务之急。目前,脱硫技术主要有催化裂化脱硫、催化加氢脱硫、水蒸气脱硫、生物催化脱硫、吸附精制脱硫、氧化脱硫等[2~5]。吸附精制法具有净化度高、能耗低、易于操作等优点,高效的脱硫吸附剂制备是过程开发的关键。负载金属离子的活性纤维是脱除汽油中硫醇的一种…     

An efficient synthesis of 3-cyano-3-benzoyloxyoxindoles via cyanoacylation of isatins in the presence of 4 Å molecular sieves

In the presence of 4 Å molecular sieves in CH₃CN, a process for the cyanobenzoylation and cyanocarbonylation of isatins with benzoycyanides and ethylcyanoformate under mild reaction conditions has been developed. This approach provides easy access to a wide range of 3-cyano-3-benzoyloxyoxindoles and 3-cyano-3-ethoxycarbonyloxyoxindoles in good to excellent yields.     

Catalytic asymmetric conjugate reduction with ethanol: A more reactive system Pd(II)-Pr-DUPHOS complex with molecular sieves 4A

We describe herein the catalytic asymmetric conjugate reduction of α,β-unsaturated carbonyl compounds using a novel cationic Pd-ⁱPr-DUPHOS complex. In this reaction, EtOH worked well as a solvent and a reducing agent, and the reaction was completed within several hours in most cases to afford the reduced compounds almost quantitatively with modest to good enantioselectivity (up to 72% ee). It was found that the Pd-ⁱPr-DUPHOS complex was more reactive than the previously reported Pd-BINAP complex when molecular sieves 4A was added as an additive. Based on an X-ray structural analysis of [Pd{(S,S)-ⁱPr-duphos}](OTf)₂ complex, a working hypothesis of the reaction mechanism is also described.     

Exploring meso-/microporous composite molecular sieves with core-shell structures

A series of core–shell‐structured composite molecular sieves comprising zeolite single crystals (i.e., ZSM‐5) as a core and ordered mesoporous silica as a shell were synthesized by means of a surfactant‐directed sol–gel process in basic medium by using cetyltrimethylammonium bromide (CTAB) as a template and tetraethylorthosilicate (TEOS) as silica precursor. Through this coating method, uniform mesoporous silica shells closely grow around the anisotropic zeolite single crystals, the shell thickness of which can easily be tuned in the range of 15–100 nm by changing the ratio of TEOS/zeolite. The obtained composite molecular sieves have compact meso‐/micropore junctions that form a hierarchical pore structure from ordered mesopore channels (2.4–3.0 nm in diameter) to zeolite micropores (≈0.51 nm). The short‐time kinetic diffusion efficiency of benzene molecules within pristine ZSM‐5 (≈7.88×10^?19 m² s^?1) is almost retainable after covering with 75 nm‐thick mesoporous silica shells (≈7.25×10^?19 m² s^?1), which reflects the greatly opened junctions between closely connected mesopores (shell) and micropores (core). The core–shell composite shows greatly enhanced adsorption capacity (≈1.35 mmol g^?1) for large molecules such as 1,3,5‐triisopropylbenzene relative to that of pristine ZSM‐5 (≈0.4 mmol g^?1) owing to the mesoporous silica shells. When Al species are introduced during the coating process, the core–shell composite molecular sieves demonstrate a graded acidity distribution from weak acidity of mesopores (predominant Lewis acid sites) to accessible strong acidity of zeolite cores (Lewis and Brønsted acid sites). The probe catalytic cracking reaction of n‐dodecane shows the superiority of the unique core–shell structure over pristine ZSM‐5. Insight into the core–shell composite structure with hierarchical pore and graded acidity distribution show great potential for petroleum catalytic processes.     

Effect of lithium addition on the performance of proton-conducting catalysts for oxidative coupling of methane under microwave irradiation

The oxidative coupling of methane over lithium modified proton-conducting catalysts irradiated by microwaves has been studied. Compared with protonconducting catalysts, lithium addition to proton-conducting catalysts resulted in changes in product species and product selectivities, favoring the production of C₂ compounds.     

介孔分子筛在生物酶固定化中的应用

综述了MCM-48和SBA-15等新型介孔分子筛用生物酶固定化载体研究的新进展。介孔分子筛由于拥有巨大的比表面积(~1000m2/g)、纳米尺寸孔道(2~50m)和较大的孔容(~1.0 cm3/g),因此以分子筛为载体利用物理吸附制备的固定化酶呈现出高的催化活性,但固定化酶操作稳定性较低,在使用过程中部分酶分子发生了脱落,其原因是分子筛表面自由的硅羟基通过物理吸附或氢键作用固定酶分子。借助介孔分子筛自身的自由硅羟基在表面嫁接-COOH、-NH2、-CH=CH2等有机官能团来构筑酶固定化的微环境,改善酶分子和载体的亲和作用,提高固定化酶的活性。目前,利用有机官能团功能化介孔分子筛固定化酶是研究发展的趋势。     

Oxidative polymerization of p-alkylphenols catalyzed by horseradish peroxidase

Enzymatic oxidative polymerization of p-alkylphenols using horseradish peroxidase as catalyst has been carried out in two polymerization solvent systems: a mixture of phosphate buffer (pH 7) and 1,4-dioxane, and a reverse micellar solution, yielding powdery polymeric materials. The polymer yield was much dependent upon the type of alkyl group in the monomer as well as the solvent type. In case of the polymerization of umbranched alkylphenols in the aqueous 1,4-dioxane, the polymer yield increased with increasing chain length of the alkyl group from 1 to 5, and the yield of the polymer from hexyl or heptylphenol was almost the same as that of the pentyl derivative. The relationship between the type of substituent and the polymer yield in the reverse micellar system was different from that in the aqueous 1,4-dioxane; the highest yield was achieved from ethylphenol. The resulting polymers had molecular weight of several thousands. The polymer was estimated to be composed from a mixture of phenylene and oxyphenylene units from IR analyses. TG measurement exhibited that the polymer had relatively high thermal stability. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1453–1459, 1997