基于超材料的微波双波段吸收器

基于闭合双环单元结构, 设计、仿真、测试了对偏振无依赖性的双波段超材料吸收器. 实验结果表明, 该设计在频率4.06 GHz和6.66 GHz存在两个显著吸收峰, 吸收率分别为99.60%和95.83%, 并且在入射角达到50°时, 吸收率仍然保持在83%以上. 由于单元结构具有旋转对称性, 使得该吸收器对偏振不敏感, 能同时实现横电波和横磁波的双波段吸收. 吸收频率决定于闭合环大小, 调节闭合环尺寸能够灵活实现特定频率的吸收. 这些优点使我们的设计在多频谱成像、热辐射探测等应用中表现出较大的潜力.     

宽带透射吸收极化无关超材料吸波体

提出了一种新的基于磁性吸波体材料的具有低频透射和高频宽带吸收特性的超材料吸波体.该超材料吸波体在1 GHz的透射系数为-0.5 dB,具有较好的低频透射特性,可以实现对低频信号的相互通信;在频率大于8.4 GHz的频段,吸收率均大于80%,基本覆盖整个X波段和Ku波段,实现高频宽带吸收.此外,由于该超材料吸波体的单元金属周期结构具有较好的四重旋转对称性,因而是极化无关的.该透射吸收超材料吸波体设计简单,实用性强,具有较强的潜在应用价值.     

一种极化不敏感和双面吸波的手性超材料吸波体

基于手性结构设计了一种极化不敏感和双面吸波的超材料吸波体.该吸波体的结构单元由手性结构和介质基板组成.仿真的电磁波正、反向入射时超材料吸波体的吸收率表明:该吸波结构的正、反面是互易的,具有双面吸波特性.仿真的不同极化角下超材料吸波体的吸收率表明:该超材料吸波体具有极化不敏感特性.仿真的不同入射角下超材料吸波体的吸收率表明:该超材料吸波体的入射角较窄.仿真的吸波体单元的表面电流和磁能密度分布表明:电、磁场之间存在交叉耦合,吸波与手性有关.仿真的不同损耗情况下超材料吸波体的吸收率表明:基板的介质损耗在吸波过程中起主导作用,金属的电阻热可以忽略不计.该超材料吸波体可能在要求双面吸波的领域中具有潜在的应用. 关键词： 极化不敏感 双面吸波 手性结构 超材料吸波体     

Multiband terahertz metamaterial absorber

This paper reports the design of a multiband metamaterial (MM) absorber in the terahertz region. Theoretical and simulated results show that the absorber has four distinct and strong absorption points at 1.69, 2.76, 3.41 and 5.06 THz, which are consistent with `fingerprints' of some explosive materials. The retrieved material parameters show that the impedance of MM could be tuned to match approximately the impedance of the free space to minimise the reflectance at absorption frequencies and large power loss exists at absorption frequencies. The distribution of the power loss indicates that the absorber is an excellent electromagnetic wave collector: the wave is first trapped and reinforced in certain specific locations and then consumed. This multiband absorber has applications in the detection of explosives and materials characterisation.     

基于宽边耦合螺旋结构的低频小型化极化不敏感超材料吸波体

设计、仿真并实验验证了基于宽边耦合螺旋结构的低频小型化超材料吸波体. 实验测试结果表明, 该超材料吸波体在1.39 GHz吸收率达到最大为98%, 其单元尺寸和总厚度均为6.8 mm, 约为1/32工作波长, 实现小型化窄带吸波. 由于吸波体中螺旋结构是旋转对称排列的, 因而其对垂直入射电磁波的极化方向是不敏感的. 此外, 该超材料吸波体对斜入射横电和横磁极化电磁波在60°时, 仍具有强吸收. 关键词： 超材料 吸波体 小型化     

A pure dielectric metamaterial absorber with broadband and thin thickness based on a cross-hole array structure

A pure dielectric metamaterial absorber with broadband and thin thickness is proposed, whose structure is designed as a periodic cross-hole array. The pure dielectric metamaterial absorber with high permittivity is prepared by ceramic reinforced polymer composites. Compared with those with low permittivity, the absorber with high permittivity is more sensitive to structural parameters, which means that it is easier to optimize the equivalent electromagnetic parameters and achieve wide impedance matching by altering the size or shape of the unit cell. The optimized metamaterial absorber exhibits reflection loss below -10 dB in 7.93 GHz-35.76 GHz with a thickness of 3.5 mm, which shows favorable absorption properties under the oblique incidence of TE polarization (±45°). Whether it is a measured or simulated value, the strongest absorbing peak reaches below -45 dB, which exceeds that of most metamaterial absorbers. The distributions of power loss density and electric and magnetic fields are investigated to study the origin of their strong absorbing properties. Multiple resonance mechanisms are proposed to explain the phenomenon, including polarization relaxation of the dielectric and edge effects of the cross-hole array. This work overcomes the shortcomings of the narrow absorbing bandwidth of dielectrics. It demonstrates that the pure dielectric metamaterial absorber with high permittivity has great potential in the field of microwave absorption.     

基于电磁谐振的极化无关透射吸收超材料吸波体

仿真并实验验证了基于电磁谐振的极化无关透射吸收超材料吸波体, 该吸波体可以实现低频透射和高频吸收.实验测试结果表明, 该吸波体在6.77 GHz 吸收率峰值为83.6%, 半功率带宽为4.3%, 实现窄带强吸收.为进一步拓展该谐振型超材料吸波体的吸收带宽, 利用其低频透射特性, 将两个工作于不同频段的吸波体叠加在一起, 测试结果表明, 复合后超材料吸波体的半功率带宽可以增大到10.9%, 吸收率也略有增强. 该超材料吸波体设计简单, 具有较强的实用性和应用前景. 关键词： 极化无关 透射吸收 超材料吸波体     

A wideband metamaterial absorber based on a magnetic resonator loaded with lumped resistors

<正>A wideband metamaterial absorber（MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loaded with lumped resistors,a dielectric substrate,and a metal plate.We simulated,fabricated,measured,and analyzed the MA. The experimental results show that the reflectance(S₁₁) is below -10 dB at normal incidence in the frequency range of 7.7 GHz-18 GHz,and the peak value is about—20 dB.Simulated power loss density distributions indicate that wideband absorption of the MA is mainly attributable to the lumped resistors in the magnetic resonator.Further investigations indicate that the distance between two unit cells along the magnetic field direction significantly influences the performance of the MA.     

太赫兹频域的强双带特异材料吸收体

We report the design and simulation of a dual-band perfect terahertz absorber which is composed of an electric Split-Resonance-Ring（eSRR） layer, polyimide spacer and a metal plate layer. The absorber has two near-unity absorptions near 0. 502 THz and 0. 942 THz and both are related to the LC resonance of the eSRR. The results show that the designed terahertz absorber is an excellent electromagnetic wave concentrator. The electromagnetic waves are firstly converged into the spacer and the eSRR layer and are then significantly absorbed.     

超薄柔性透射型超构材料吸收器

设计并加工了一种超薄柔性透射型吸收器,总体厚度为0.288 mm,可实现柔性弯曲,容易做到与曲面目标共形.该吸收器由三层结构组成,底层是金属光栅,中间为介质层,表面单元由两条平行放置的尺寸不同的金属线组成.仿真和实验结果表明,对横电波在5和7 GHz的吸收分别达到97.5%和96.0%,对横磁波在3.0—6.5 GHz都能保持90%以上的透射率.两个吸收频点可分别独立调节,增加了设计的灵活性.另外,当入射角增大到60°时,该吸收器的性能基本不受影响,表现出良好的广角特性.     

Actively tunable dual-broadband graphene-based terahertz metamaterial absorber

A tunable metamaterial absorber (MA) with dual-broadband and high absorption properties at terahertz (THz) frequencies is designed in this work. The MA consists of a periodic array of flower-like monolayer graphene patterns at top, a SiO₂ dielectric spacer in middle, and a gold ground plane at the bottom. The simulation results demonstrate that the designed MA has two wide absorption bands with an absorption of over 90% in frequency ranges of 0.68 THz-1.63 THz and 3.34 THz-4.08 THz, and the corresponding relative bandwidths reach 82.3% and 20%, respectively. The peak absorptivity of the absorber can be dynamically controlled from less than 10% to nearly 100% by adjusting the graphene chemical potential from 0 eV to 0.9 eV. Furthermore, the designed absorber is polarization-insensitive and has good robustness to incident angles. Such a high-performance MA has broad application prospects in THz imaging, modulating, filtering, etc.     

太赫兹频域的强双带特异材料吸收体(英文)

We report the design and simulation of a dual-band perfect terahertz absorber which is composed of an electric Split-Resonance-Ring(eSRR) layer, polyimide spacer and a metal plate layer. The absorber has two near-unity absorptions near 0.502 THz and 0.942 THz and both are related to the LC resonance of the eSRR. The results show that the designed terahertz absorber is an excellent electromagnetic wave concentrator. The electromagnetic waves are firstly converged into the spacer and the eSRR layer and are th...     

极薄宽角度平面超材料吸波体仿真与实验验证

仿真和实验验证了厚度极薄的平面结构超材料吸波体, 该吸波体采用加载交指电容的耶路撒冷十字结构, 通过增加单元间的耦合电容显著降低了其工作频率. 测试结果表明, 该超材料吸波体在1.58 GHz, 吸收率峰值为88.48%, 其厚度为2 mm, 约为1/95工作波长, 吸波体的单元尺寸为11 mm, 约为1/17工作波长. 此外, 通过金属通孔将耶路撒冷十字结构与金属底板相连接, 使其对斜入射横电和横磁极化电磁波具有宽角度吸收特性, 在60°时依然具有较高的吸收率, 且吸收峰频率几乎不发生偏移, 从而使其更具实用价值. 关键词： 极薄 宽角度 超材料吸波体     

工字形太赫兹超材料吸波体的传感特性研究

利用超材料吸波体对材料参数的电磁响应, 可将其应用于传感. 本文设计了一种工字形单元结构的超材料吸波体, 基于频域算法对其在太赫兹频段的传感特性进行数值模拟, 研究了待测样品折射率、厚度及电介质隔层厚度对超材料吸波体传感器的频率灵敏度、振幅灵敏度及品质因数的影响. 研究结果表明:当待测样品厚度为40 μm时, 折射率频率灵敏度可达到153.17 GHz/RIU, 折射率振幅灵敏度可达到41.37%/RIU; 待测样品折射率一定时, 厚度频率灵敏度随其厚度的增大而线性减小; 随着待测样品厚度的增加, RFOM呈增大趋势, 但增大幅度在逐渐减小; TFOM随待测样品厚度的增加而减小.     

太赫兹波段电磁超材料吸波器折射率传感特性

太赫兹超材料吸波器作为一类重要的超材料功能器件,除了可以实现对入射太赫兹波的完美吸收外,还可以作为折射率传感器实现对周围环境信息变化的捕捉与监测.通常从优化表面金属谐振单元结构和改变介质层材料和形态两个方面出发,改善太赫兹超材料吸波器的传感特性.为深入研究中间介质层对太赫兹超材料吸波器传感特性的影响,本文基于金属开口谐...     

极化无关双向吸收超材料吸波体的仿真与实验验证

设计并制作出极化无关双向吸收超材料吸波体.仿真结果表明,该吸波体对斜入射横电极化和横磁极化电磁波具有较好的吸收效果,其强损耗主要来自介质基板的介电损耗.实验测试结果表明,该吸波体在11.1 GHz对垂直入射电磁波实现双向强吸收,吸收率分别为95.9％和90.8％.该吸波体厚度较薄,工作波长约为1/34.该超材料吸波体具有吸收率高、厚度薄、设计简单、易于加工等优点.     

Design of a varactor-tunable metamaterial absorber

In this paper, we design a varactor-tunable metamaterial absorber （MA）. The tunable MA is based on a mushroom-type high impedance surface （HIS）, in which varactors are loaded between adjacent metal patches to adjust the capacitance and tune the resonance frequency, the primary ground plane is etched as the bias network to bias all of the varactors in parallel, and another ultra-thin grounded film is attached to the bottom. Its absorption characteristics are realized for electrically dielectric loss. The simulated values of a sample indicate that a tunable frequency range from 2.85 GHz to 2.22 GHz is achieved by adjusting the varactor capacitance from 0.1 pF to 2.0 pF, and better than 0.97 absorbance is realized; in addition, the tunable frequency range is expanded from 4.12 GHz to 1.70 GHz after optimization.     

Tunable broadband metamaterial absorber consisting of ferrite slabs and a copper wire

A tunable broadband metamaterial absorber is demonstrated at microwave frequencies in this paper.The metamaterial absorber is composed of ferrite slabs with large resonance beamwidths and a copper wire.The theoretical analysis for the effective media parameters is presented to show the mechanism for achieving the perfect absorptivity characteristic.The numerical results of transmission,reflectance,and absorptivity indicate that the metamaterial absorber exhibits a near perfect impedance-match to free space and a high absorptivity of 98.2% for one layer and 99.97% for two layers at 9.9 GHz.The bandwidth with the absorptivity above 90% is about 2.3 GHz.Moreover,the absorption band can be shifted linearly in a wide frequency range by adjusting the magnetic bias.This metamaterial absorber opens a way to prepare perfectly matched layers for engineering applications.     

基于电阻型频率选择表面的低频宽带超材料吸波体的设计

基于电阻型频率选择表面(Resistance Frequency Selective Surface, RFSS) 设计了一种低频宽带、 极化不敏感和宽入射角特性的超材料吸波体. 该吸波体的基本单元由开槽十字型平面超材料(Cave Cross Planar Metamaterial, CCPM)、 RFSS、 电介质基板和金属背板组成. 采用FDTD方法数值模拟得到的结果表明: 相比于单纯的CCPM吸波体、 RFSS吸波体, CCPM和RFSS复合结构吸波体低频吸收特性得到极大改善, 在整个1-5 GHz频率范围内, 吸收率大于80%, 吸收峰值达到98%以上. 数值模拟得到的不同极化角和不同入射角下的吸收率表明: 该复合结构吸波体具有极化不敏感和宽角度吸收特性.     

A flexible ultra-broadband metamaterial absorber working on whole K-bands with polarization-insensitive and wide-angle stability

For potential military applications, a flexible metamaterial absorber (MMA) working on whole K-bands with total-thickness of 3.367 mm, ultra-broadband, polarization-insensitive, and wide-angle stability is presented based on frequency-selective surface (FSS). The absorber is composed of polyvinyl chloride (PVC) layer, polyimide (PI) layer, and poly tetra fluoro ethylene (PTFE) layer, with a sandwich structure of PVC-PI-PTFE-metal plate. Periodic conductive patterns play a crucial role in the absorber, and in traditional, it is designed on the upper surface of PI layer to form LC resonance. Different from commonly absorber, all the patterns are located on the lower surface of the PI layer in this work, and hence the impedance matching and absorptivity are improved in this purposed absorber. The flexible absorber with patterns on lower surface of the PI layer is compared with that on upper surface of the PI layer, the difference and the reasons are explained by absorption mechanism based on equivalent circuit model, and surface current density and electric field distribution are used to analyze resonance peaks. Absorptivity is greater than 90% in a frequency range of 10.47 GHz-45.44 GHz with relative bandwidth of 125.1%, covering the whole Ku, K, Ka, and some of X, U bands, especially containing the whole K bands from 12 GHz to 40 GHz. Radar cross section (RCS) is reduced at least 10 dB in 11.48 GHz-43.87 GHz frequency ranges, and absorption remained about 90% when the incident angle changed from 0° to 55°. The purposed absorber is fabricated, measured, and experiment results show good agreement with theoretical analysis and numerical simulation. After bonded on outer surface of different cylinders with diameters of 200 mm and 100 mm, the absorption of MMA is approximately reduced 10% and 20% respectively, which shows good conformal character with surface of various curvatures. Due to the attractive performance on strong absorption in the whole K-bands, flexible and easy conformal, our design exhibits broad potential application in radar stealth and sensors.