活性炭纤维的微孔结构水吸附

测定了两种活性炭纤维（ACF）的氮气、水吸附等温线和XPS,研究了ACF的微孔结构和表面性质,用αs图分析氮吸附等温线获得了ACF的比表面积、微孔容量和微孔径。XPS表明在ACF表面存在多种不同结合状态的氧。水在ACF上的吸附等温线呈V型,具有很大的脱附滞后环。水通过与ACF表面的氧形成氢键发生吸附。ACF表面的初始吸附点多,则在低、中压时的水吸附量就大。     

活性碳纤维吸附的研究Ⅰ-不同工艺制备的活性碳纤维的性能比较

本文比较研究了五种不同工艺制备的活性碳纤维（ACF）的产率、比表面积、孔结构、对有机溶剂蒸汽的吸附和脱附性能、对水溶液中亚甲基兰、苯酚和碘的吸附性能以及它们的热稳定性。实验结果表明，水蒸气活化的ACF比化学活化的ACF有更大的比表面积，但前者产品产率较低而后者很高；不论水蒸气活化还是化学活化的ACF，它们对有机溶剂饱和蒸汽的吸附量都较高，脱附和再吸附的性能也都较好，对水溶液中的苯酚都有较好的吸附能力，但化学活化的ACF对亚甲基兰的吸附量显著小于水蒸气活化的ACF，同时磷酸活化的ACF-P对碘的吸附量也明显偏小；除了用KOH活化的ACF外，其它ACF都有很好的热稳定性。     

PAN基活性炭纤维床层上有机溶剂蒸汽的穿透特性

本文考察了PAN基活性炭纤维（ACF）床层对低浓度有机溶剂蒸汽的吸附行为，并应用了Yoon—Nelson理论，发现穿透曲线可用改进的方程式来表达，得到了吸附剂ACF2的吸附常数及三氯乙烯、甲苯的总吸附传质系数。     

壳聚精对铬离子(Ⅲ)的吸附研究

本文研究了结晶态与非结晶态的壳聚糖对Cr（Ⅲ）的吸附动力学和吸附等温线。结果表明，非结晶态的壳聚糖对Cr（Ⅲ）的吸附速率、吸附容量均大于结晶态的壳聚糖。结晶态的壳聚糖对Cr（Ⅲ）的吸附容量随其颗粒直径的增大而下降，而非结晶态的壳聚糖的颗粒大小对其吸附容量的影响不明显。钠、钾阳离子的存在，对壳聚糖分离Cr（Ⅲ）的效果几乎没有影响，但是EDTA存在时，会严重地阻碍壳聚糖对Cr（Ⅲ）的吸附作用。     

取代基效应对三苯甲酸纤维素酯类吸附剂的吸附性能的影响

采用催化合成法制备三苯甲酸纤维素酯（CTB）、三（4-甲基苯甲酸）纤维素酯（CTMB）和三（4-氯苯甲酸）纤维素酯（CTCB），将其分别负载于Gas Chrom Q载体上，用不同类型的探针分子及气相色谱法表征其吸附性能，研究取代基团的电子效应和空间效应对其吸附性能的影响。实验结果表明：在三苯甲酸纤维素酯类吸附剂和苯衍生物吸附质的苯环上的取代基效应（电子效应和立体效应）对吸附质在吸附剂上的吸附热（-Δha）的影响显著，但两者的影响各不相同。     

用FTIR和XPS研究ACF的表面结构

采用红外光谱（FTIR）及X光电子能谱（XPS），系统分析了纤维碳化各阶段的结构、不同程度活化的ACF的结构以及低温氧化后和热处理后ACF的结构，提出了ACF表面结构模型。     

活性炭纤维电吸附重金属及磺胺甲恶唑性能研究

使用盐酸对吸附剂活性炭纤维（activated carbon fiber,ACF）进行改性,通过SEM、BET和FTIR对改性前后的ACF形貌及结构进行系统表征发现,改性后ACF较改性前表面杂质减少且沟壑更加明显,比表面积提高22%,微孔体积增加5%,含氧官能团（C-O和C=O）明显增多. 以水中重金属离子（Zn(II)及Cr(VI)）和抗生素磺胺甲恶唑（Sulfamethoxazole,SMX）为目标污染物,研究改性后ACF对目标污染物的吸附（静吸附和电吸附）性能,考察了浓度、pH、外加电压对吸附的影响. 结果表明,ACF用量为5 g,电压为1.2 V,Zn(II)、Cr(VI)及SMX浓度均为10 mg·L^-1,Zn(II)溶液pH为5时,ACF吸附水中Zn(II)的最大吸附量为9.25 mg·g^-1,是静吸附条件的2.15倍;Cr(VI)溶液pH为4时,ACF吸附Cr(VI)的最大吸附量为8.86 mg·g^-1,是静吸附条件的1.96倍;SMX溶液pH为6时,ACF吸附SMX的最大吸附量为8.32 mg·g^-1,是静吸附条件的1.84倍. ACF吸附Zn(II)、Cr(VI)及SMX的动力学曲线均符合准二级动力学模型,吸附过程为化学吸附. Freundlich等温模型能更好地描述ACF对Zn(II)、Cr(VI)及SMX的吸附特性,其吸附形式为多分子层吸附. ACF通过电极反接方式进行循环再生,脱附速率快且脱附效果明显,经4次循环再生后,ACF对Zn(II)、Cr(VI)及SMX的去除率均在90%以上.     

活性炭纤维对气相低浓度三氯乙烯的动态吸附

研究了3种不同经表面积活性炭纤维（ACF）对气相低浓度三氯乙烯（TCE）的动态吸附。ACF的比表面积为600m^2/g、1400m^2／g和1600m^2/g，TCE的浓度范围为27mg/m^3-2725mg/m^3。结果表明，比表面积为1400m^2/g和1600m^2/g的ACF对TCE的吸附较好；10％穿透时间的对数与TCE匠对数呈线性关系；穿透时间随温度和湿度的增加而缩短；穿透曲线可以用经验公式拟合。拟合值和实测值吻合良好；ACF吸附是去除气相低浓度TCE的有效方法。     

云南沱茶自混合水溶液中吸附除砷（Ⅲ）的特性研究

本文通过分析云南沱茶的结构特征，以及在不同浓度、时间、PH、温度及表面活性剂存在时，自混合水溶液中吸附除砷（Ⅲ）的特性，并通过吸附模型解释了观察到的实验现象。     

异丙基膦酸单(1-己基-4-乙基)辛酯萃淋树脂吸萃重稀土元素(Ⅲ)

本文研究了异丙基膦酸单（１－己基－４－乙基）辛酯萃淋树脂在盐酸介质中对重稀土元素（Ⅲ）的吸萃平衡，考察了平衡水相酸度对吸附反应的影响，计算了重稀土（Ⅲ）间的平均分离系数，确定了吸附反应的Ｆｒｅｕｄｌｉｃｈ等温吸附方程。该树脂吸附Ｙｂ（Ⅲ）的静态饱和容量为６６．５ｍｇＹｂ／（ｇ．Ｒ），饱和萃合物的ＩＲ谱表明ＰＴ－２萃淋树脂吸附Ｙｂ（Ⅲ）的反应为阳离子交换反应。     

Influence of heat treatment of rayon-based activated carbon fibers on the adsorption of formaldehyde

The influence of heat treatment of rayon-based activated carbon fibers on the adsorption behavior of formaldehyde was studied. Heat treatment in an inert atmosphere of nitrogen for rayon-based activated carbon fibers (ACFs) resulted in a significant increase in the adsorption capacities and prolongation of breakthrough time on removing of formaldehyde. The effect of different heat-treatment conditions on the adsorption characteristics was investigated. The porous structure parameters of the samples under study were investigated using nitrogen adsorption at the low temperature 77.4 K. The pore size distributions of the samples under study were calculated by density functional theory. With the aid of these analyses, the relationship between structure and adsorption properties of rayon-based ACFs for removing formaldehyde was revealed. Improvement of their performance in terms of adsorption selectivity and adsorption rate for formaldehyde were achieved by heat post-treatment in an inert atmosphere of nitrogen.     

Influence of anodic treatment on heavy metal ion removal by activated carbon fibers

In this work, the effect of electrochemical oxidation treatment on activated carbon fibers (ACFs) was studied in the context of Cr(VI), Cu(II), and Ni(II) adsorption behavior. Ten weight percent phosphoric acid (A-ACFs) and ammonia (B-ACFs) were used for acidic and basic electrolytes, respectively. Surface properties of ACFs were determined by X-ray photoelectron spectroscopy (XPS). The specific surface area and the pore structure were evaluated from nitrogen adsorption data at 77 K. As a result, the electrochemical oxidation treatment led to an increase in the amount of oxygen-containing functional groups. Also, the adsorption capacity of the electrochemically oxidized ACFs was improved in the order B-ACFs > A-ACFs > untreated-ACFs, in spite of a decrease in specific surface area which resulted from pore blocking by functional groups and pore destruction by acidic electrolyte. It was clearly found that the heavy metal ions were largely influenced by the functional groups on the ACF surfaces.     

活性碳纤维的结构修饰及其吸附氙性能的研究

活性炭纤维对氙的吸附容量与其孔结构密切相关，为了提高活性炭纤维对氙气的吸附容量，本文分别用亚甲基蓝、对硝基苯酚等有机物，或氯化钠、碘等无机化合物填充的方法修饰活性炭纤维的孔结构；以及利用高锰酸钾或硝酸等氧化处理修饰活性炭纤维的表面化学性质，同时，利用低温氮等温吸附表征了这些改性活性炭纤维的孔结构，以及通过光电子能谱表征了改性活性炭纤维的表面化学结构，上述化合物充填或氧化改性活性炭纤维对氙的吸附性能的研究结果表明，适量化合物填充，或合适浓度硝酸对活性炭纤维的表面处理，可以有效地修饰活性炭纤维的孔结构或改变活性炭纤维表面对氙的亲和力。因而可有效地提高改性活性炭纤维对氙的吸附容量。     

Nitrogen Adsorption Studies of PAN-Based Activated Carbon Fibers Prepared by Different Activation Methods

Polyacrylonitrile (PAN)-based activated carbon fibers (ACFs) prepared by various activation methods were characterized using low-temperature nitrogen adsorption over a wide relative pressure from 10⁻⁶ to 1. Nitrogen adsorption is a standard tool for determination of porous structure parameters. In the present work, we carried out extensive adsorption studies of a series of PAN-ACFs activated by different methods. It was shown that the high-resolution α_S plot provided valuable information about structural properties of samples under study. The pore size distributions of samples under study were calculated by employing the regularization method according to density functional theory. By these analyses, the pore development and the dominant pores of samples prepared by different methods can be clearly observed. Moreover, the adsorption measurement could provide profound insight into the structural heterogeneity of the ACFs.     

Studies on pore structures and surface functional groups of pitch-based activated carbon fibers

The present study concerns the physical activation and chemical oxidation of pitch-based activated carbon fibers (ACFs) as ways to improve the adsorption properties. The surface oxides of the ACFs studied were determined by Boehm's titration and the pore structures were studied by the BET method with N(2)/77 K adsorption. Also, the adsorption properties of the ACFs were investigated with chromium ion adsorption by different adsorption models. As a result, it was observed that carboxyl groups were largely created after nitric acid treatment on ACFs. The affinity for chromium ions increases with increasing specific surface area, micropore volume, and surface functionalities of ACFs as the activation time increases.     

Formaldehyde removal by Rayon-based activated carbon fibers modified by <Emphasis Type="Italic">P</Emphasis>-aminobenzoic acid

We impregnated Rayon-based activated carbon fibers (ACFs) by p-aminobenzoic acid (PABA) and systematically investigated their porous structure, surface chemistry, and formaldehyde removal behavior. Using standard nitrogen adsorption analysis, we found that the specific surface area, the micropore volume, and the total pore volume decreased with increasing concentration of PABA. Through elemental analysis and X-ray photoelectron spectroscopy, it was found that some nitrogen-containing functional groups presented on the surface of modified Rayon ACFs. The modified Rayon-based ACFs showed much higher adsorption capacity and longer breakthrough time for formaldehyde than did as-prepared Rayon-based ACF. We proposed that the improvement of formaldehyde removal by modified ACFs was attributed to the combined effects of physisorption contributed by pore structures and chemisorption contributed by the N-containing functional groups, whereas there was only physisorption between the as-prepared ACF and formaldehyde molecules.     

Adsorption properties of iodine-doped activated carbon fiber

Iodine-doped activated carbon fibers (ACFs) were prepared by the iodine immersion method on pitch-based ACF. Then iodine-doped ACFs were heated in argon at 523 K for 4 h and at 673 K for 2 h. The iodine structure of the resultant iodine-doped ACFs was examined using X-ray photoelectron spectroscopy. The micropore structures were determined by N(2) adsorption at 77 K. The surface area and micropore volume of iodine-doped ACFs are less than those of pristine ACFs. However, the pore width does not change with the iodine doping. The effects of iodine doping on adsorption properties of ACFs for H(2)O and NO at 303 K were examined. The iodine doping affected remarkably the adsorptivities of ACFs for H(2)O and NO. In particular, iodine-doped ACFs treated at 673 K show enhanced adsorptivities for H(2)O and NO. This result suggests that iodine molecules doped on the micropores should be charged by heat treatment at 673 K.     

A study on NO removal of activated carbon fibers with deposited silver nanoparticles

In this study, activated carbon fibers (ACFs), onto which silver (Ag) nanoparticles have been introduced by an electroplating technique, were used to remove NO. Surface properties of the ACFs were determined by X-ray diffraction and scanning electron microscopy. N2 adsorption isotherms at 77 K were investigated by BET and t-plot methods to characterize the specific surface areas and pore volumes, and NO removal efficiency was confirmed by a gas chromatographic technique. As for the experimental results, Ag content on the ACFs increased with plating time. However, adsorption properties such as the BET specific surface area and the total pore volume were somewhat decreased in the presence of Ag nanoparticles. NO removal efficiency of all Ag-ACFs was higher than that of untreated ACFs and increased with Ag content. However, a decrease in the extent of NO removal was shown in the excessively plated ACFs, which might be associated with the blocking of the micropores in the carbon; therefore, an optimal Ag content needs to exist in the presence of initially well-developed micropores to lead to an increase in the efficient NO removal ability of the ACF.     

STUDY ON THE FACTORS AFFECTING REDUCTION CAPACITIES OF ACTIVATED CARBON FIBERS

1. INTRODUCTION The discharge of effluent containing precious metal ions, which comes from electroplating, mining, smelting, and other industries, not only contaminate the environment where people live, but also cause the waste of natural resources. From…     

Preparation and characterization of activated carbon fibers supported with silver metal for antibacterial behavior

In this work, the effect of immersion in silver nitrate solution on activated carbon fibers (ACFs) was investigated in relation to adsorption behavior and antibacterial activity of ACFs supported with silver (ACF/Ag). The pore and surface properties were studied in terms of BET volumetric measurement with nitrogen adsorption, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The antibacterial activities of ACF/Ag were studied in broth dilution tests against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) from a point of view of water purification. As an experimental result, the silver content of ACF/Ag increased with increasing concentration of silver nitrate. It was found that the micropore structure slightly decreased as the silver nitrate concentration increased. Otherwise, it was revealed that the ACF/Ag possessed a strong antibacterial activity and an inhibitory effect for the growing of E. coli and S. aureus, respectively. Silver content on ACF/Ag decreased rapidly because of rough morphology of silver particles in water erosion.