电活性聚乳酸纳纤膜的形态调控及高效捕集PM0.3性能

通过静电喷雾沸石咪唑框架-8(ZIF-8)分散液对同步电纺聚乳酸(PLA)纳米纤维进行表面功能化,以增强PLA/ZIF-8纳米纤维膜(简称纳纤膜)表面的电荷俘获及储存能力,从而提高静电吸附效果和过滤性能.通过在分散液中添加不同量的ZIF-8来调控锚定于纤维表面的ZIF-8负载量,探究ZIF-8含量与纤维膜形态和性能演变之间关系.采用扫描电子显微镜(SEM)对纤维膜的微观形态进行表征,并结合傅里叶变换红外光谱(FTIR)和X射线衍射谱(XRD)分析了纤维膜的化学性质、界面相互作用和晶体结构的演变机理.采用静电测试仪、电介质测试仪和静电计分别评价表面电势、相对介电常数和输出电压,表征纤维膜的电活性和摩擦电输出性能.通过万能试验机测试聚乳酸纳米纤维膜的力学性能,并使用自主搭建的空气过滤测试平台探究纤维膜高效过滤机理.结果表明,PLA/ZIF-8纳纤膜具有高电活性、高过滤效率、低空气阻力和优异的力学性能:其表面电势和最大开路输出电压分别可达5.9 kV和30.9 V,与纯PLA对比样相比分别提升5.6倍和5.3倍,同时拉伸强度和拉伸韧性增幅分别高达78%和111%.更重要的是,PLA/ZIF-...     

聚乙丙交酯电纺纳米纤维膜的等离子体改性及性能研究

采用等离子体表面处理的方法, 通过正交实验设计, 以纤维膜表面引入的氮含量为响应变量, 确定了NH3等离子体改性PLGA电纺纤维膜的最佳条件, 并在PLGA纤维膜表面成功地引入了功能性氨基基团. 研究结果表明, 改性后PLGA电纺纤维膜的力学性能有所降低, 但表面亲水性明显增强.     

改性羟基磷灰石/聚乳酸纳米复合材料的结晶行为

利用溶剂复合的方法制备了具有良好生物相容性的表面接枝聚(γ-苄基-L-谷氨酸)的改性羟基磷灰石/聚乳酸纳米复合材料, 并研究了其熔融与结晶行为. 结果表明, 聚乳酸的玻璃化转变温度为60.3 ℃, 而复合材料的玻璃化转变温度达到65.8 ℃, 不同样品在140 ℃等温结晶后, 改性羟基磷灰石/聚乳酸复合材料的球晶直径仅为聚乳酸(PLLA)球晶直径的16.7%~66.7%. 复合材料的熔点提高到184.4 ℃.     

聚乙二醇-b-聚乳酸的合成及其电纺形成超细纤维研究

为了提高聚乳酸的亲水性,以辛酸亚锡为催化剂、聚乙二醇单甲醚(mPEG)为大分子引发剂进行丙交酯(LLA)开环聚合,合成聚乙二醇-b-聚乳酸两嵌段共聚物(PELA).以红外光谱1、H核磁共振谱、接触角测试、差热扫描量热分析等方法对PELA的结构及性能进行表征.结果表明,通过调控mPEG与LLA的投料比可以控制PELA的相对分子质量,而随着mPEG组分含量或链长增加,共聚物亲水性增强,但其Tg、Tcc、Tm有所降低.由普通电纺制备PELA超细纤维,并分别由乳液电纺和同轴电纺得到以水溶性聚氧化乙烯(PEO)为芯、PELA为壳的芯/壳结构复合超细纤维(E-PEO/PELA和C-PEO/PELA).扫描电镜和透射电镜结果表明,PELA、E-PEO/PELA和C-PEO/PELA超细纤维形貌良好.随着PELA中mPEG含量的增加,电纺PELA纤维膜的吸水率增强,而由乳液电纺和同轴电纺制备的PEO/PELA芯/壳结构超细纤维膜,亲水性均好于PELA超细纤维膜.     

金纳米棒负载的静电纺丝纤维的制备及其表面增强拉曼光谱性能

为简单有效地制备高活性表面增强拉曼光谱(Surface-enhanced Raman Spectroscopy,SERS)基底。本文采用静电纺丝聚乙烯醇(PVA)/聚丙烯酸(PAA)纳米纤维为支撑材料,通过直接浸泡的方法,利用金纳米棒与电纺纤维之间的静电力,使纳米棒在纤维表面自组装,得到了性能优异的SERS基底。通过透射电子显微镜、扫描电子显微镜对金纳米棒以及不同状态下的电纺纤维的形貌进行表征,结果表明,金纳米棒均匀且密集地负载在纤维表面。通过设置不同的浸泡时间确定了金纳米棒组装平衡的时间为12 h,并通过调控纺丝时间和金纳米棒的浓度发现随着纺丝时间和金纳米棒浓度的增加,复合纤维膜SERS增强效果随之提升。该复合纤维膜具有优异的SERS均匀性,并且能够检测到浓度低至10~(-10)mol/L的4-氨基苯硫酚的存在。     

聚己内酯/聚丁内酰胺电纺纤维的制备及性能

通过溶液静电纺丝法制备了聚己内酯/聚丁内酰胺（PCL/PBL）电纺纤维膜。采用扫描电子显微镜（SEM）、水相接触角测量仪、原子力显微镜（AFM）、能谱仪（EDS）、透射电子显微镜（TEM）、X射线衍射仪（XRD）、热重分析仪（TGA）、差示扫描量热仪（DSC）、电子万能拉力机对PCL/PBL电纺纤维的形貌、亲疏水性、结晶性能、热性能及力学性能进行了研究。结果表明，随着PBL含量的增加，纤维直径增大、分布变窄，且纤维膜的亲水性明显改善；PCL与PBL有一定相容性，PCL/PBL电纺纤维膜的结晶度高于PCL或PBL均聚物电纺纤维膜，并随PBL含量增加而提高；PCL/PBL电纺纤维膜中PCL熔点随PBL含量增加而略有增加，PBL组分的熔点则基本不变。两组分的结晶温度和纤维膜热稳定性均随PBL含量增加而降低。PBL的加入使电纺纤维膜的力学性能明显提高。     

聚乳酸-乙醇酸/纳米氧化锌复合电纺纤维装载亲疏水药物的控释及体外细胞毒性

利用静电纺丝技术制备了负载亲水性药物阿霉素(DOX)以及疏水性药物喜树碱(CPT)的复合纳米纤维. 先用巯基封端的普朗尼克(F127)修饰纳米氧化锌(FZnO), 再将FZnO负载盐酸阿霉素(DOX@FZnO), 最后将DOX@FZnO与CPT一起纺入聚乳酸-乙醇酸(PLGA)纤维中. 体外药物释放结果表明, 复合纳米纤维能够减小亲水性药物的突释, 减缓药物释放速率, 延长药物释放时间. 体外细胞活性结果表明, 双载药复合纤维比单载药复合纤维具有更强的细胞毒性, 能够有效抑制癌细胞生长.     

微波辅助仿生矿化增强石墨烯与聚乳酸的界面相互作用

石墨烯纳米片在提高聚乳酸(PLA)复合材料力学性能和气体阻隔性能等方面具有良好的应用前景,但通常在不同程度上受限于较差的界面相互作用.本文通过高效且环境友好的微波辅助水相仿生矿化方法,在石墨烯纳米片表面直接生成高结晶度、高结构规整度的羟基磷灰石纳米晶须,获得了具有良好分散性和界面结合力的仿生矿化石墨烯(BMGr)纳米杂化体.将BMGr纳米杂化体均匀分布于聚乳酸纤维表面,通过受限成型(60℃,3 MPa)获得了具有强界面结合的复合薄膜,大幅提高了力学性能.值得强调的是,BMGr增强聚乳酸复合薄膜的拉伸强度、杨氏模量和拉伸韧性分别达到22.6 MPa,199 MPa和6.6 MJ/m³,是纯PLA纤维膜的6.46,3.75和8.25倍.本文不仅发展了有效修饰石墨烯纳米片的技术路线,更为制备高强度高韧性的聚乳酸复合材料并阐述其结构-性能关系提供了研究思路.     

具有抗菌性能的载药复合微纳米纤维的制备及其结构和性能表征

利用静电纺丝技术制备了一种具有抗菌性能的氧化锌(ZnO)/聚乳酸(PLA)/聚己内酯(PCL)载药微纳米纤维膜,并通过扫描电子显微镜(SEM)、X射线衍射(XRD)和傅里叶变换红外光谱(FTIR)分别对复合膜的表面形态、元素组成和化学结构进行表征。通过抗菌实验评价了复合膜的抗菌性能,用紫外分光光度计测试复合膜在体外的药物释放行为。结果显示,以物理共混的方式将ZnO和氢溴酸高乌甲素(LAH)成功载入复合微纳米纤维;与PLA/PCL复合微纳米纤维膜相比,ZnO/PLA/PCL复合微纳米纤维膜表现出更好的抗菌效率。当ZnO含量为10%(wt)时,复合微纳米纤维膜具有最佳的抗菌性能;药物释放性能结果表明,ZnO/PLA/PCL复合微纳米纤维膜具有良好的药物缓释性能。     

明胶/聚乳酸复合纤维膜的制备、表征及作为角膜细胞载体的评价

利用静电纺丝技术制备了明胶与聚乳酸的复合纤维膜, 研究了组分配比对复合膜的表面性能、孔隙结构和力学性能的影响, 并以复合膜为组织工程支架进行兔角膜上皮细胞的体外培养. 采用扫描电子显微镜、免疫荧光染色和噻唑蓝四氮唑溴化物(MTT)比色法综合评价了细胞在支架表面的黏附与增殖能力. 结果表明, 纺丝溶液的组分对纤维的直径分布和表面亲水性有显著影响, 不同组分配比的复合纤维膜均具有高孔隙率的通孔结构; 以明胶为基材可维持复合膜的细胞黏附性; 与聚乳酸复合可以明显提高复合膜的力学性能.     

SiW11掺杂二氧化硅纳米纤维(SiW11/SiO2)的制备及对拟南芥叶中多胺的萃取分析

采用静电纺丝技术制备了SiW₁₁掺杂的二氧化硅纳米纤维(SiW₁₁/SiO₂)材料, 其中掺杂的SiW₁₁质量占纤维质量的7.83%, 制备的SiW₁₁/SiO₂材料尺寸均一, 在考察的pH范围内带负电, 与未掺杂SiW₁₁的二氧化硅纳米纤维相比, SiW₁₁/SiO₂材料表现出强阳离子交换作用, 能有效萃取尸胺和腐胺. 在最优条件下, 建立了注射器分散固相萃取(In syringe dSPE)-超高效液相色谱-串联质谱联用(UHPLC-MS/MS)检测拟南芥样品中多胺的方法. 结果表明, 尸胺和腐胺分别在10~1000和20~1000 ng/mL浓度范围内具有良好的线性关系(R²≥0.9950), 检出限和定量限分别为0.5~0.9和1.6~3.0 ng/mL. 将该方法应用于拟南芥样品中尸胺和腐胺的检测, 加标回收率在87.5%~111.3%之间, 相对标准偏差RSD<5.0%. 建立的SiW₁₁/SiO₂制备方法解决了多金属氧酸盐(POM)在修饰改性过程中存在的制备繁琐、 固载量少的问题, 拓宽了POM在分离领域中的应用.     

Miscibility and crystallinity of poly(3-hydroxybutyrate)/poly(3-hydroxybutyrate-co-3-hydroxyvalerate) blends

With the objective of developing new biodegradable materials, the miscibility and the crystallinity of blends of poly(3-hydroxybutyrate), P(3HB), and poly(3-hydroxybutyrate-co-3-hydroxyvalerate), P(3HB-co-3HV), have been studied. P(3HB) (300 kg mol⁻¹)/P(3HB-co-3HV)–10% 3HV (340 kg mol⁻¹) blends were prepared by casting in a wide range of proportions, and characterized by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR). The experimental values for the glass transition temperatures (T_g) are in good agreement with the values provided by the Fox equation, showing that the blends are miscible. It was observed that the T_g and the melting temperature (T_m) decreases with the increase in the P(3HB-co-3HV)–10% 3HV content, while the crystallization temperature (T_c) increases. FT-IR analyses confirmed the decrease on the crystallinity of P(3HB)/P(3HB-co-3HV)–10% 3HV blends with higher copolymer contents. Bands related to the crystallinity were changed, due to the copolymer content that produced miscible and less crystalline blends.     

Effects of Wood Flour (WF) Pretreatment and the Addition of a Toughening Agent on the Properties of FDM 3D-Printed WF/Poly(lactic acid) Biocomposites

In order to improve the properties of wood flour (WF)/poly(lactic acid) (PLA) 3D-printed composites, WF was treated with a silane coupling agent (KH550) and acetic anhydride (Ac₂O), respectively. The effects of WF modification and the addition of acrylicester resin (ACR) as a toughening agent on the flowability of WF/PLA composite filament and the mechanical, thermal, dynamic mechanical thermal and water absorption properties of fused deposition modeling (FDM) 3D-printed WF/PLA specimens were investigated. The results indicated that the melt index (MI) of the specimens decreased after WF pretreatment or the addition of ACR, while the die swell ratio increased; KH550-modified WF/PLA had greater tensile strength, tensile modulus and impact strength, while Ac₂O-modified WF/PLA had greater tensile modulus, flexural strength, flexural modulus and impact strength than unmodified WF/PLA; after the addition of ACR, all the strengths and moduli of WF/PLA could be improved; after WF pretreatment or the addition of ACR, the thermal decomposition temperature, storage modulus and glass transition temperature of WF/PLA were all increased, and water absorption was reduced.     

γ-Fe2O3纳米纤维的丙酮敏感特性

采用静电纺丝法制备了PVP/FeC₆H₅O₇复合纳米纤维, 并将复合纤维在500 ℃高温烧结3 h, X射线衍射分析(XRD)表明, 烧结后的产物为正尖晶石结构的γ-Fe₂O₃晶体. 扫描电子显微镜(SEM)观测结果表明, 制得了直径均匀、 连续的复合纳米纤维, 其平均直径约为1000 nm; 烧结后的γ-Fe₂O₃纳米纤维保持了其连续性, 但纤维发生了收缩, 直径较烧结前小, 平均约为600 nm. 比表面积分析表明, γ-Fe₂O₃纳米纤维比表面积为57.18 m²/g. 气敏性能测试结果表明, 230 ℃为γ-Fe₂O₃纳米纤维检测丙酮气体的最佳工作温度. 在此温度下, γ-Fe₂O₃纳米纤维对丙酮气体表现出高响应度[S=6.9, c(Acetone)=7.88×10⁴ mg/m³]和线性度(7.88×10²~1.58×10⁵ mg/m³浓度范围内). 同时, γ-Fe₂O₃纳米纤维气体传感器件还表现出良好的长期稳定性.     

Isothermal curing of an epoxy resin by alternating differential scanning calorimetry

The quasi-isothermal curing of a diepoxide resin with a triamine of polyoxypropylene was studied by alternating differential scanning calorimetry (ADSC), which is a temperature modulated DSC technique. The complex heat capacity measurements allows to analyse the vitrification process at curing temperatures (T_c) below the maximum glass transition of the fully cured epoxy (T_g∞=85.8°C). Initially, the modulus of the complex heat capacity, |C^*_p|, increases until a maximum (conversion between 0.42 and 0.56) and then decreases. This step is followed by an abrupt decay of |C^*_p|, due to the vitrification of the system, which allows the determination of the vitrification time. This value agrees well with that determined by the partial curing method. The phase angle and out-of-phase heat capacity show an asymmetric wide peak during the vitrification process. The change in |C^*_p| at vitrification decreases with the increase of T_c becoming zero at temperature T_g∞. This epoxy-triamine system shows a delay of the vitrification process respect to other model epoxy systems probably due to the presence of polyoxypropylene chains in the network.

The decay of |C^*_p| during vitrification may be normalised between unity and zero by defining a mobility factor. This mobility factor has been used to simulate the reaction rate during the stage where the reaction is controlled by diffusion. The observed reaction rate is simulated by the product of the kinetic reaction rate, determined by the autocatalytic model, and the mobility factor.     

A mild photoactivated hydrophilic/hydrophobic switch

Surface modification using light is one of the most powerful methods for controlling the physical and chemical properties offunctionalized surfaces. In this paper, we report on systems where soft UV irradiation (lambda = 365 nm) converts a "low" activity fluorocarbon to a "high" activity amine-functionalized surface. An amine-functionalized SAM (self-assembled monolayer) is first masked using a tertiary amine catalyzed reaction with an N-hydroxysuccinimidyl carbonyl reagent. This mild, room-temperature reaction introduces a hydrophobic photocleavable nitrobenzyl "protecting group" terminated with a fluorocarbon end-chain. UV irradiation (lambda = 365 nm) of this hydrophobic/fluorocarbon surface cleaves the nitrobenzyl residue, returning the surface to the original hydrophilic/amine-functionalized state. This provides a mild, generic method of producing surfaces with hydrophilic/hydrophobic patterns or patterned with amine functional residues. Two different protecting groups, one terminated with a single and the other with three fluorocarbon end chains, are compared. In the case of the more bulky protecting group, only a small proportion of the amine residues react, but the surface is equally hydrophobic and the amine residues equally well shielded from further reaction. Surfaces are characterized by X-ray photoelectron spectroscopy, ellipsometry, surface potential, and contact angle measurements. Images of the photopatterned SAMs were obtained using scanning electron microscopy.     

Melting and glass transitions in paraffinic and naphthenic oils

Naphthenic and paraffinic oils were analyzed by modulated differential scanning calorimetry (MDSC). The results showed several improvements in the analysis of thermal properties when compared with standard DSC. The glass transition temperature (T_g), the enthalpy relaxation at T_g, and the melting endotherms could be deconvoluted, and reversible melting could be identified. This allowed for an easier interpretation of the thermal properties of the oils. With MDSC, the T_gs in mineral oils were found to coincide with endothermic enthalpy relaxation, which is generally regarded as a melting endotherm with standard DSC. A decrease in heat capacity after T_g was attributed to the existence of rigid amorphous material. From Δc_p at T_g and the oil molecular weight, the number of repeat units in the oil chains was estimated at less than 20. The T_g of a hypothetical pure aromatic oil was found to be similar to that for petroleum asphaltenes, and that for a naphthenic oil of infinite molecular weight to be similar to that of petroleum resins.     

Thermal and topographical characterization of polyester- and styrene/acrylate-based composite powders by scanning probe microscopy

The thermal properties of two conventional polyester-based toners and a chemically prepared styrene/acrylate toner with different thermal histories were studied by scanning probe microscopy (SPM) and differential scanning calorimetry (DSC). The thermal transition temperatures detected by SPM agreed with the results of the DSC measurements. The validity of SPM for detecting thermal transitions was further confirmed by studying two amorphous reference polymers with different glass transition points (T_g) and three crystalline reference polymers with different melting points (T_m). When the toner sample was heated by the SPM probe above the glass transition temperature of the toner powder (T_probe > T_g), changes occurred in the surface topography and roughness causing different levels of local sintering of the particles. A set of roughness parameters calculated from the SPM image data were used to quantify the most essential features of toner surfaces. Environmental scanning electron microscopy (ESEM) was used to study the penetration depth of heat dissipated by the SPM probe. The probe-annealing was compared with oven-annealing in order to establish the effect of thermal history on the thermal properties of the materials.     

快速扫描量热法研究聚对苯二甲酸-1,4-环己烷二甲醇酯的结晶和熔融行为

采用快速扫描量热法(FSC)结合传统的差示扫描量热仪(DSC)考察了聚对苯二甲酸-1,4-环己烷二甲醇酯(PCT)聚酯在接近玻璃化转变(T_g)和熔融温度(T_m)范围(100~270 ℃)的结晶和熔融行为。 较大过冷度时PCT聚酯结晶较快,FSC有效地抑制降温过程结晶的发生,而较低过冷度下传统DSC可以避免样品降解对实验结果的影响,二者的结合能很好地对PCT聚酯结晶动力学进行测量,实验结果表明在175 ℃时结晶速率最快。 并且利用Flash DSC对等温结晶温度下形成的片晶熔点进行加热速率的相关测量,在熔融动力学建模的基础上进行校准,以确定零加热速率下片晶的熔点。 Hoffman-Weeks方程中T_m与结晶温度(T_c)的线性关系与T_c=T_m的交点给出了PCT晶体的平衡熔融温度$T_m^o$为315 ℃。     

Heat capacities of NaNO3 and KNO3 from 350 to 800 K

The heat capacities of NaNO₃ and KNO₃ were determined from 350 to 800 K by differential scanning calorimetry. Solid-solid transitions and melting were observed at 550 and 583 K for NaNO₃ and 406 and 612 K for KNO₃, respectively. The entropies associated with the solid-solid transitions were measured to be (8.43± 0.25) J K⁻¹ mole⁻¹ for NaNO₃ and (13.8±0.4) J K⁻¹ mole⁻¹ for KNO₃. At 298.15 K the values of C⁰_P S⁰_P, {H⁰(T)-H⁰(0)}/T and -{G⁰(T)-H⁰(0)}/T, respectively, are 91.94, 116.3, 57.73, and 58.55 J K⁻¹ mole⁻¹ for NaNO₃ and 95.39, 133.0, 62.93, and 70.02 J K⁻¹ mole⁻¹ for KNO₃. Values for S⁰_T, {H⁰(T)-H⁰(0)}/T, and -{G⁰(T)-H⁰(0)}/T were calculated and tabulated from 15 to 800 K for NaNO₃ and KNO₃.