Dislocation glide in GaN films grown by the lateral-overgrowth method induced by low-energy electron-beam irradiation

The effect of irradiation on the dislocation structure of epitaxial GaN films, grown by the lateral-overgrowth method, is studied using the electron-beam-induced current mode in a scanning electron microscope. Low-energy electron-beam irradiation is found to lead to the gliding basal-plane dislocations even at very low excitation levels. Changes in the relative contrast of two segments of adjacent basal-plane dislocations may also indicate dislocation movement in the prismatic planes.     

Ab initio study of screw dislocations in Mo and ta: A new picture of plasticity in bcc transition metals

We report the first ab initio density-functional study of <111> screw dislocation cores in the bcc transition metals Mo and Ta. Our results suggest a new picture of bcc plasticity with symmetric and compact dislocation cores, contrary to the presently accepted picture based on continuum and interatomic potentials. Core energy scales in this new picture are in much better agreement with the Peierls energy barriers to dislocation motion suggested by experiments.     

Increase in the fatigue durability of stainless steel by electron-beam surface treatment

The structure, phase composition and dislocation substructure of 20Cr23Ni18 steel subjected to electron-beam treatment and subsequent multicycle fatigue loading until destruction were studied by scanning and transmission electron microscopy. It was shown that electron-beam treatment with an energy density of 20 J/cm² increases the fatigue durability by a factor of 2.1. The cause of steel fatigue destruction is analyzed and a way of further increasing the fatigue durability is proposed.     

Orientation dependence of screw dislocation motion in b.c.c. transition metals

A tight-binding type electronic theory is used to calculate the Peierls stress of the screw dislocation in b.c.c. transition metals. The repulsive core-core interaction energies are simulated by Born-Mayer type potentials as well as the modified Born-Mayer potentials. It is shown that there are essential differences in the orientation dependence of the screw dislocation motion among the transition metals, in agreement with experiments.     

In situ investigation of the effect of a magnetic field on the mobility of dislocations in deformed KCl:Ca single crystals

This paper presents the results of an experimental investigation into the mobility of edge dislocations in KCl:Ca single crystals and the effect of a static magnetic field of 0.3 T on the dislocation mobility. The experiments on the effect of a magnetic field on the dislocation mobility were carried out with the use of a high-resolution (1 ms) method that permits in situ measurements of the sample dipole moment induced by the motion of charged dislocations as the crystal is being deformed. It is found that the starting stress is reduced in a magnetic field and the activation volume for overcoming of point defects by the dislocations is increased. It is further found that the magnetic field increases the rate of motion of the dislocations at the initial stage of deformation (to the point of dislocation multiplication) but has no effect on the mobility in the multiplication stage. Fiz. Tverd. Tela (St. Petersburg) 39, 630–633 (April 1997)     

温度对镍基单晶高温合金γ/γ'相界面上错配位错运动影响的分子动力学研究

用分子动力学方法研究了温度对镍基单晶高温合金γ/γ'相界面上错配位错运动的影响.研究结果表明:无论是在低温还是在高温下,错配位错的运动都是通过扭折的形核及扭折沿位错线的迁移来实现;在低温时错配位错的相互作用有利于错配位错的运动;然而在高温时错配位错的相互作用可以阻碍错配位错的运动,从而阻碍γ和γ'相界面的相对滑动,有利于提高镍基单晶高温合金的高温力学性能. 关键词： 镍基单晶高温合金 相界面 错配位错 分子动力学模拟     

Mechanism of Strain Rate Effect Based on Dislocation Theory

Based on dislocation theory, we investigate the mechanism of strain rate effect. Strain rate effect and dislocation motion are bridged by Orowan＇s relationship, and the stress dependence of dislocation velocity is considered as the dynamics relationship of dislocation motion. The mechanism of strain rate effect is then investigated qualitatively by using these two relationships although the kinematics relationship of dislocation motion is absent due to complicated styles of dislocation motion. The process of strain rate effect is interpreted and some details of strain rate effect are adequately discussed. The present analyses agree with the existing experimental results. Based on the analyses, we propose that strain rate criteria rather than stress criteria should be satisfied when a metal is fully yielded at a given strain rate.     

Application of neutron stress diffractometry for studies of residual stresses and microstrains in reactor pressure vessel surveillance specimens reconstituted by beam welding methods

The high-resolution neutron-diffraction technique is used to determine the residual stresses and microstrains in unirradiated reactor pressure vessel surveillance specimens reconstituted by means of different welding methods. Comparative analysis of the results demonstrates that the lowest level of residual stresses is observed in the specimens reconstituted via electron-beam welding. The level of microstrains thereof is maximum, indicating a high dislocation density in the material.     

The gauge theory of dislocations: A nonuniformly moving screw dislocation

We investigate the nonuniform motion of a straight screw dislocation in infinite media in the framework of the translational gauge theory of dislocations. The equations of motion are derived for an arbitrarily moving screw dislocation. The fields of the elastic velocity, elastic distortion, dislocation density and dislocation current surrounding the arbitrarily moving screw dislocation are derived explicitly in the form of integral representations. We calculate the radiation fields and the fields depending on the dislocation velocities.     

Elastic stress of moving dislocations in finite crystals

The elastic stress of a single crystal with finite dimensions is investigated by means of the linear continuum theory; external forces and dislocation motion are assumed to be known. A formal solution is derived with a Green's dyadic. The dyadic is expanded in a series, the first term of which delivers the well-known solution for infinite crystals, the following terms describe successive reflections of sound at the surface of the finite crystal. They can be computed by iteration. This expansion corresponds to the physical situation of pulse-echo-experiments. Fourier transforms lead to analogous expressions describing the influence of the surface on time-periodic dislocation experiments.     

Fluorescence studies of electron-beam pumped POPOP dye vapor

Fluorescence studies on electron-beam excited mixtures of POPOP dye vapor and various buffer gases are reported. Xenon has been found to be a promising candidate as a buffer gas for efficient energy deposition of the electron-beam and energy transfer to the POPOP dye vapor. These experiments may be an important step towards realization of an electrically excited dye vapor laser. Work supported in part by the National Aeronautics and Space Administration and the Energy Research and Development Administration.     

钼晶体中存在有柏格斯矢量为〈100〉的位错的实验证据

实验结果表明:以乙二酸水溶液为电解浸蚀液,可以在钼单晶体表面上显示位错的浸蚀斑。选{100}面为观察面,沿三叉亚晶界定出了浸蚀斑密度。观测结果证实了不对称倾侧晶界的Read-shockley公式,由此确定了沿亚晶界排列的浸蚀斑与柏格斯矢量为<100>的刃型位错间的一一对应关系。 关键词：     

重复频率强流电子束二极管实验研究

 采用静电场模拟对二极管结构及导引磁场位形分布进行了优化设计，利用设计的二极管在高压脉冲发生器上进行了重复频率运行实验研究，给出了相应测试波形，并对不同材料阴极、不同真空度情况下二极管的发射特性进行了比较。在二极管真空度满足一定要求（p＜0.01Pa）条件下以在重复频率方式运行时，不论是石墨阴极还是金属阴极，输出电子束流都比较稳定。设计的二极管电子束电压超过500kV，电流约5kA，脉冲宽度40ns，重复频率100Hz。     

Accurate velocity mapping with FAcE

Spin dislocation between the slice selection, phase encoding, and frequency encoding is a source of image distortions. Two strategies can be pursued to improve the appearance of moving spins in an image. Either the sequence is made equally sensitive to velocity-dependent dislocation artifacts for all spatial directions or the sensitivity is reduced with a shorter echo time. The first approach increases the dislocation for the phase-encoding direction and is therefore not useful if velocity maps with minimal distortion are the goal. FAcE (FID acquired echoes) is a sequence with separate sampling of the left and right k-space half-planes that allows for very short echo times. It was applied for velocity mapping of flow in the slice select direction. Special attention was paid to a compact design of the velocity-encoding select gradient to achieve short echo times even with high velocity sensitivity. Artifacts introduced by in-plane motion were studied for FAcE and conventional gradient-echo sequences, both in phantom experiments and simulation. FAcE allows for very short echo times with inherent motion compensation of the frequency-encoding gradient. Thus, both motion-related dislocation artifacts and signal voids due to coherence loss in regions with irregular flow are minimal.     

Statistical description of the shape of a moving dislocation

The shape and mobility of dislocations gliding (climbing) over the crystal relief are studied. The mobility of a dislocation is governed by the probability of critical nucleation on it of various defects (the formation of a double kink or break-away from a barrier during sliding, the formation of a jog during absorption (emission) of an interstitial (vacancy) during climbing, etc.). It is demonstrated that the transitional and steady-state modes of dislocation motion exist (the transitional and steady-state modes of deformation). The time required to achieve the steady-state dislocation motion and the velocity of this motion in the absence and in the presence of various types of pinning (drag) centers are calculated. The pinning centers qualitatively change the steady-state velocity of dislocations and increase the time required to reach this mode of motion.     

The stress-velocity relationship of twinning partial dislocations and the phonon-based physical interpretation

The dependence of dislocation mobility on stress is the fundamental ingredient for the deformation in crystalline materials. Strength and ductility, the two most important properties characterizing mechanical behavior of crystalline metals, are in general governed by dislocation motion. Recording the position of a moving dislocation in a short time window is still challenging, and direct observations which enable us to deduce the speed-stress relationship of dislocations are still missing. Using large-scale molecular dynamics simulations, we obtain the motion of an obstacle-free twinning partial dislocation in face centred cubic crystals with spatial resolution at the angstrom scale and picosecond temporal information. The dislocation exhibits two limiting speeds: the first is subsonic and occurs when the resolved shear stress is on the order of hundreds of megapascal. While the stress is raised to gigapascal level, an abrupt jump of dislocation velocity occurs, from subsonic to supersonic regime. The two speed limits are governed respectively by the local transverse and longitudinal phonons associated with the stressed dislocation, as the two types of phonons facilitate dislocation gliding at different stress levels.     

Small amplitude approximation and stabilities for dislocation motion in a superlattice

Starting from the traveling wave solution, in small amplitude approximation, the Sine-Gordon equation can be re- duced to a generalized Duffing equation to describe the dislocation motion in a superlattice, and the phase plane properties of the system phase plane are described in the absence of an applied field. The stabilities are also discussed in the presence of an applied field. It is pointed out that the separatrix orbit describing the dislocation motion as the kink wave may transfer the energy along the dislocation line, keep its form unchanged, and reveal the soliton wave properties of the dislocation motion. It is stressed that the dislocation motion process is the energy transfer and release process, and the system is stable when its energy is minimum.     

非对称倾侧亚晶界的晶体相场法研究

采用晶体相场法研究非对称倾侧亚晶界结构及其在应力作用下的微观运动机制.分别从温度、倾斜度角以及应力施加方向等方面对其结构及迁移过程进行分析和讨论.结果表明,非对称倾侧亚晶界由符号相同的一排刃型位错等距排列,部分出现由两个相互垂直排列的刃型位错构成的位错组;在应力作用下,非对称倾侧亚晶界迁移的微观机制包括位错的滑移和攀移、位错组分解、单个位错与位错组反应、单个位错分解以及位错湮灭;温度降低和倾斜度增大都会阻碍亚晶界的迁移过程;应力方向改变导致位错运动方向改变,从而改变晶界迁移形式.     

拉曼型自由电子激光器中相对论电子运动稳定性的比较研究

拉曼型自由电子激光器作为一种兆瓦级高功率毫米波、太赫兹波辐射源, 其电子的运动稳定性对整体器件的性能至关重要.本文采用科尔莫戈罗夫熵方法, 以典型的麻省理工学院公布的实验数据为例, 比较研究拉曼型正向导引磁场和反向导引磁场两类自由电子激光器中相对论电子的运动稳定性. 结果表明:摇摆器绝热压缩磁场对电子运动的稳定性无实质性影响, 但对电子运动影响大; 电子束自身场在拉曼型正向导引磁场自由电子激光器中使电子运动稳定性变差, 而在拉曼型反向导引磁场自由电子激光器中则可改善电子运动稳定性. 关键词： 拉曼型自由电子激光器 相对论电子运动稳定性 科尔莫戈罗夫熵 电子束自身场     

THE ELECTRON-BEAM IRRADIATION ON THE HIGH TEMPERATURE SUPERCONDUCTING THIN FILMS: A NUMERICAL SIMULATION OF THE LOW TEMPERATURE SCANNING ELECTRON MICROSCOPY

Low-temperature scanning electron microscopy (LTSEM) is a promising measuring technique for probing the spatial distribution of the superconducting properties of the high-temperature superconducting (HTS) thin films. A theoretical analysis of the electron-beam irradiation on the HTS thin films in the LTSEM has been carried out. An inhomogeneously distributed grain array model has been applied in the analysis, and some numerical sim-ulations have been carried out on the electron-beam induced voltage (EIV) signals in the LTSEM experiments. The comparisons of our numerical results with the LTSEM experi-mental data indicate that it is quite reasonable to use a two-dimensional Josephson junction array for stimulating the inhomogeneous HTS thin film sample. Our numerical results also show that the EIV signals are influenced by the electron-beam power used in the LTSEM, and a reduction of the electron-beam power is suggested in order to eliminate the errors in estimating the local values of critical temperature T_c and critical current I_c by the sample temperature and the bias current at which the first EIV signal occurs.