NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

Aqueous dye adsorption on ordered mesoporous carbons

Ordered mesoporous carbons (OMCs) with varying pore size, and microporous carbon, CFY, were synthesized using ordered mesoporous silica SBA-15 and NaY zeolite as hard templates, respectively. N(2) adsorption tests show that the synthesized OMCs possess abundant mesopores and centralized mesopore distribution. Methylene blue (MB) and neutral red (NR) were used as probe molecules to investigate their adsorption behaviors on OMCs and CFY. As evidenced by adsorption tests, the volume of mesopores of which the pore size is larger than 3.5 nm is a crucial factor for the adsorption capacity and adsorption rate of MB on OMCs. However, the most probable pore diameter of OMCs was found to be vital to the adsorption capacity and adsorption rate of NR. Theoretical studies show that the adsorption kinetics of MB and NR on OMCs can be well depicted by using pseudo-second-order kinetic model.     

NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

有序介孔炭的合成及液相有机大分子吸附性能研究

分别采用有序介孔氧化硅SBA-15和NaY分子筛为硬模板合成了系列有序介孔炭OMC和微孔炭CFY. N₂静态吸附测试表明, 所合成的介孔炭具有丰富的介孔结构和集中的介孔分布. 以亚甲基蓝为探针分子, 研究其在有序介孔炭OMC和微孔炭CFY上的吸附行为. 研究结果表明, 有序介孔炭中大于3.5 nm的大介孔孔容是决定亚甲基蓝吸附容量和吸附速率的关键因素. 吸附动力学理论研究表明, 准二级动力学方程可以很好地描述亚甲基蓝分子在介孔炭上吸附动力学行为.     

Adsorption of aqueous alkylphenol ethoxylate surfactants by mesoporous carbon CMK-3

Mesoporous carbon, CMK-3, was prepared using hexagonal SBA-15 mesoporous silica as the template and the adsorption of nonylphenol ethoxylates (NPE) onto CMK-3 was investigated. The adsorption process was well described using pseudo-second-order kinetics. At initial NPE concentrations of 107 and 530 mg l(-1), the adsorption rate constants were found to be 5.6 x 10(-3) and 8.7 x 10(-4) g mg(-1) min(-1), indicating that a higher initial concentration or adsorption amount resulted in a lower adsorption rate. NPE adsorption onto CMK-3 fitted a Langmuir-Freundlich model and the maximum amounts of NPE absorbed at 15, 25, and 35 degrees C were 923, 720, and 463 mg g(-1), suggesting an elevated adsorption capacity of CMK-3 for NPE with decreased adsorption temperature. In addition, increasing adsorption temperature led to the change of the adsorption model from the Langmuir-Freundlich to the Langmuir model. N2 adsorption results showed that the adsorption of NPE led to a decrease in the mesopore volume of CMK-3. However, the pore width of NPE-loaded CMK-3 was found to be identical to that of CMK-3.     

孔径渐变的有序介孔炭的合成及电化学应用

以SBA-15为模板,硼酸为孔道扩张剂,蔗糖为碳源制备了一系列孔径渐变的有序硼杂介孔炭材料,并研究了其电化学电容性能。氮气静态吸附测试表明,当硼酸物质的量分数从0%增大到75%时,介孔炭的孔径从3.3nm增大至8.1nm,并保持有序的介孔结构。电化学测试表明,在KOH电解液中,硼杂介孔炭比电容明显高于未掺杂硼有序介孔炭,孔道有序性和孔径大小共同影响了炭材料的电容性能。当硼酸物质的量分数为50%时,炭材料的比电容性能最优。     

Effect of pore packing defects in 2-d ordered mesoporous carbons on ionic transport

Ordered mesoporous materials show great importance in energy, environmental, and chemical engineering. The diffusion of guest species in mesoporous networks plays an important role in these applications, especially for energy storage, such as supercapacitors based on ordered mesoporous carbons (OMCs). The ion diffusion behavior in two different 2-D hexagonal OMCs was investigated by using cyclic voltametry and electrochemical impedance spectroscopy. In addition, transmission electron microscopy, small-angle X-ray diffraction, and nitrogen cryosorption methods were used to study the pore structure variations of these two OMCs. It was found that, for the OMC with defective pore channels (termed as pore packing defects), the gravimetric capacitance was greatly decayed when the voltage scan rate was increased. The experimental results suggest that, for the ion diffusion in 2-D hexagonal OMCs with similar mesopore size distribution, the pore packing defect is a dominant dynamic factor.     

Adsorption of hydrogen isotopes on micro- and mesoporous adsorbents with orderly structure

The equilibrium and dynamic adsorption data of H(2) and D(2) on different micro- and mesoporous adsorbents with orderly structure including 3A, 4A, 5A, Y, and 10X zeolites; carbon CMK-3; silica SBA-15; and so forth were collected. Critical effect of the nanodimension of adsorbents on the adsorption behavior of hydrogen and its isotopes is shown. The highest adsorption capacity was observed at pore size 0.7 nm, but equal or even larger isotope difference in the equilibrium adsorption was observed at larger pore sizes, whereas the largest isotope difference in the dynamic adsorption was observed at 0.5 nm. The adsorption rate of D(2) is larger than that of H(2) in microporous adsorbents, but the sequence could be switched over in mesoporous materials. Linear relationship was observed between the adsorption capacity for hydrogen and the specific surface area of adsorbents although the adsorbents are made of different material, which provides a convincing proof of the monolayer mechanism of hydrogen adsorption. The linear plot for microporous adsorbents has a larger slope than that for mesoporous adsorbents, which is attributed to the stronger adsorption potential in micropores.     

Electrochemical Oxidation and Detection of Morphine at Ordered Mesoporous Carbon Modified Glassy Carbon Electrodes

In this work, three ordered mesoporous carbons (OMCs) with different structural parameters were synthesized by a simple variation of the hydrothermal temperature of the silica templates (SBA‐15). X‐ray diffraction and nitrogen adsorption‐desorption results show these OMCs exhibit an ordered 2D hexagonal mesostructure with tunable pore diameter. OMC‐modified glassy carbon electrodes exhibit efficient electrocatalytic reactivity toward oxidation of morphine (MO). The amperometric detection of MO in pH 7.0 phosphate buffered saline at +0.39 V versus Ag/AgCl is the lowest potential reported to‐date. A linear range from 0.2 to 197.6 μM and a detection limit of 0.03 μM MO were obtained.     

有序介孔碳材料的软模板合成、结构改性与功能化

有序介孔碳材料在吸附、分离、催化以及能量存储/转化等方面具有广阔的应用前景。相较于复杂的硬模板路线,基于两亲性嵌段共聚物和聚合物前驱体间（如酚醛树脂）自组装的软模板路线是合成有序介孔碳材料更为有效的方法。本文讨论比较了溶剂挥发诱导自组装法、水相协同自组装法和无溶剂法等三种典型软模板路线的基本过程和特点,并介绍了近年来在新型碳前驱体应用、介孔碳的结构改性和功能化等方面的一些重要进展,最后总结了介孔碳的合成研究中所需解决的关键问题。     

Adsorption hysteresis in ordered mesoporous silicas

We review some recent progress in experimental studies of the adsorption hysteresis of simple molecules in ordered mesoporous silicas. We show that the nature of the adsorption hysteresis due to capillary condensation can be examined with less ambiguity by measuring the hysteresis loop for the ordered mesoporous silicas with three types of pore geometries (cylindrical, interconnected cylindrical, and interconnected spherical) over a wide temperature range. The adsorption hysteresis arises from the metastability of a confined phase and the temperature at which the hysteresis disappears is lower than the critical temperature of vapor-liquid equilibrium in pores. The hysteresis occurs mainly on the desorption rather than adsorption branch, irrespective of the pore geometries.     

有机胺修饰具有较大孔径介孔材料的二氧化碳吸附性能

以非离子表面活性剂P123为模板剂,正硅酸甲酯为硅源,通过加入不同的扩孔剂制得具有较大孔径的SBA-15类介孔材料,并采用粉末X射线衍射(XRD)、低温氮气吸附-脱附、扫描电镜(SEM)、傅里叶变换红外(FTIR)光谱等手段对所得样品进行了表征.加入扩孔剂可以明显增大介孔材料的孔容和孔径,而异辛烷为扩孔剂的扩孔效果明显优于四氯化碳.经四乙烯五胺(TEPA)镀饰后,这些样品均表现出良好的CO2吸附性能.其中对于除去模板剂后再镀胺的样品,其CO2吸附能力与介孔材料孔道结构关系不大,而对于未除模板剂的原粉镀胺样品,CO2吸附能力则随孔道的变大而增强.此外,通过吸附等温线和CO2-程序升温脱附(TPD)手段比较了温度和压力对CO2吸附的影响,发现在较高温度下吸附时CO2的吸附能力随压力的变化存在显著差别,因而在这类TEPA修饰的介孔材料上可通过变压吸附的途径来实现对环境气流中CO2的吸附和分离.     

Pore-size tunable mesoporous zirconium organophosphonates with chiral L-proline for enzyme adsorption

Mesoporous zirconium organophosphonates with a tunable mesopore (pore diameter: from 4.8 to 16.3 nm) were synthesized through co-condensation of ZrCl4 and 1-phosphomethylproline (H3PMP) with the aid of organic additives in the presence of an anionic surfactant (sodium dodecyl sulfate) under weak acidic conditions. The organic additives, tetrahydrofuran, can effectively strengthen the assembly of ZrCl4 and H3PMP around the surfactant micelles through decreasing the hydrolysis and condensation rate of ZrCl4. The results of the N2 sorption isotherm and SEM image show that zirconium phosphate with a bimodal structure is formed by calcination of mesoporous zirconium organophosphonate. Mesoporous zirconium organophosphonates can effectively adsorb lysozyme (Lz) and papain, and the adsorption equilibrium for Lz can be reached within 30 min. The adsorption capacity for Lz and papain can reach as high as 438 and 297 mg/g, respectively. Furthermore, Lz adsorbed on mesoporous zirconium organophosphonates can retain its structural conformation as in its free state, and no leaching of Lz from the solid was observed when shaking the Lz-loaded solid in a buffer solution. Also, the existence of L-proline in the mesopore could help the adsorption of papain at a pH value lower than the pI of papain.     

Protein adsorption on the mesoporous molecular sieve silicate SBA-15: effects of pH and pore size

A mesoporous molecular sieve silicate, SBA-15, with three pore sizes (38.1 A, 77.3 A, and 240 A) has been synthesized using a non-ionic, tri-block copolymer as a template in a sol-gel method. The effects of synthesis conditions on the pore size and pore-size distribution of this adsorbent have been described. The adsorption of proteins on these crystalline, ordered, materials has been studied. The kinetics of adsorption and equilibrium capacity have been probed with three proteins of different dimensions. The effects of electrostatic interactions and protein size are illustrated. It has been shown that SBA-15 materials can be tailored to show size selectivity for proteins, and very high capacities (450 mg/g) can be obtained. Furthermore, the rates of adsorption are shown to be dependent on the pore size, protein structure and solution pH.     

Functionalized mesoporous materials for adsorption and release of different drug molecules: A comparative study

The adsorption capacity and release properties of mesoporous materials for drug molecules can be improved by functionalizing their surfaces with judiciously chosen organic groups. Functionalized ordered mesoporous materials containing various types of organic groups via a co-condensation synthetic method from 15% organosilane and by post-grafting organosilanes onto a pre-made mesoporous silica were synthesized. Comparative studies of their adsorption and release properties for various model drug molecules were then conducted. Functional groups including 3-aminopropyl, 3-mercaptopropyl, vinyl, and secondary amine groups were used to functionalize the mesoporous materials while rhodamine 6G and ibuprofen were utilized to investigate the materials’ relative adsorption and release properties. The self-assembly of the mesoporous materials was carried out in the presence of cetyltrimethylammonium bromide (CTAB) surfactant, which produced MCM-41 type materials with pore diameters of ∼2.7-3.3 nm and moderate to high surface areas up to ∼1000 m²/g. The different functional groups introduced into the materials dictated their adsorption capacity and release properties. While mercaptopropyl and vinyl functionalized samples showed high adsorption capacity for rhodamine 6G, amine functionalized samples exhibited higher adsorption capacity for ibuprofen. While the diffusional release of ibuprofen was fitted on the Fickian diffusion model, the release of rhodamine 6G followed Super Case-II transport model.     

Templated Synthesis of Ordered Mesoporous Carbons with Tailored Structures and Morphologies

Due to the excellent biocompatibility and the capability to load and release drugs, ordered mesoporous carbons (OMCs) have been highly prospective and valuable in drug delivery system. In this contribution, synthesis of OMCs with tailored pore sizes from 4.1 to 3.4 nm was achieved by employing SBA‐15 as template and furfuryl alcohol (FA) as carbon precursors. An array of OMCs with controlled structures and morphologies by incipient wetness with FA was analyzed by powder X‐ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), and Raman spectroscopy. The resulting carbon replicas retained the hexagonal symmetry of the silica templates SBA‐15 with p6mm space group, although the framework suffered shrinkage in the replicated process. The pore size distribution, uniformity and pore volume of the mesopores in the OMCs were affected by structural properties of the SBA‐15 templates as shown by N₂ sorption and XRD pattern analysis. The process had the advantage that the textural parameters of the obtained OMCs were tunable simply by varying aging temperature of the silica template and the ratio of carbon precursor.     

Preparation and drug release behavior of temperature-responsive mesoporous carbons

A temperature-responsive composite based on poly (N-isopropylacrylamide) (PNIPAAm) and ordered mesoporous carbons (OMCs) has been successfully prepared by a simple wetness impregnation technique. The structures and properties of the composite were characterized by infrared spectroscopy (IR), X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ sorption, thermogravimetric analysis (TG) and differential scanning calorimetry (DSC). The results showed that the inclusion of PNIPAAm had not greatly changed the basic ordered pore structure of the OMCs. Ibuprofen (IBU) was selected as model drug, and in vitro test of IBU release exhibited a temperature-responsive controlled release delivery.     

Nitrogen-doped cobalt nanoparticles/nitrogen-doped plate-like ordered mesoporous carbons composites as noble-metal free electrocatalysts for oxygen reduction reaction

In this work, nitrogen-doped cobalt nanoparticles/nitrogen-doped plate-like ordered mesoporous carbons(N/Co/OMCs) were used as noble-metal free electrocatalysts with high catalytic efficiency. Compared with OMCs with long channel length, due to more entrances for catalytic target accessibility and a short pathway for rapid diffusion, the utilization efficiency of cobalt nanoparticles inside the plate-like OMCs with short pore length is well improved, which can take full advantage of porous structure in electrocatalysis and increase the utilization of catalysts. The active sites in N/Co/OMCs for oxygen reduction reaction(ORR) are highly exposed to oxygen molecule, which results in a high activity for ORR. By combination of the catalytic properties of nitrogen dopant, incorporation of Co nanoparticles, and structural properties of OMCs, the N/Co/plate-like OMCs are highly active noble-metal free catalysts for ORR in alkaline solution.     

Efficient synthesis and sulfonation of ordered mesoporous carbon materials

Ordered mesoporous carbons (OMCs) with hexagonal structure were efficiently synthesized via cooperative self-assembly of phenol/formaldehyde resol and surfactant F127 under acidic aqueous conditions. Induced by HCl, a gel phase mainly containing phenol/formaldehyde resol and F127 was obtained within several hours. X-ray diffraction (XRD), transmission electron microscope (TEM) and nitrogen adsorption isotherms indicated that the synthesized samples possess 2-D hexagonal mesostructure. The influence of the synthesis conditions, including acid concentration and mass ratio of resol to F127, was investigated. When the acid concentration was fixed in the range of 0.6-2.0 M and the mass ratio of resol to F127 in the range of 3.5-4.0, highly ordered mesoporous carbon could be synthesized. The synthesized OMCs could be easily sulfonated in concentrated sulfuric acid at elevated temperature. The results indicate that the mesostructural stability and the content of the surface sulfonic acid (SO(3)H) groups depend mainly on the pyrolysis temperature of the OMCs and the sulfonation temperature, suggesting that the combination of pyrolysis and sulfonation temperature is essential for developing OMCs with high densities of SO(3)H groups.     

Synthesis of mesoporous carbons using ordered and disordered mesoporous silica templates and polyacrylonitrile as carbon precursor

Mesoporous carbons were synthesized from polyacrylonitrile (PAN) using ordered and disordered mesoporous silica templates and were characterized using transmission electron microscopy (TEM), powder X-ray diffraction, nitrogen adsorption, and thermogravimetry. The pores of the silica templates were infiltrated with carbon precursor (PAN) via polymerization of acrylonitrile from initiation sites chemically bonded to the silica surface. This polymerization method is expected to allow for a uniform filling of the template with PAN and to minimize the introduction of nontemplated PAN, thus mitigating the formation of nontemplated carbon. PAN was stabilized by heating to 573 K under air and carbonized under N2 at 1073 K. The resulting carbons exhibited high total pore volumes (1.5-1.8 cm3 g(-1)), with a primary contribution of the mesopore volume and with relatively low microporosity. The carbons synthesized using mesoporous templates with a 2-dimensional hexagonal structure (SBA-15 silica) and a face-centered cubic structure (FDU-1 silica) exhibited narrow pore size distributions (PSDs), whereas the carbon synthesized using disordered silica gel template had broader PSD. TEM showed that the SBA-15-templated carbon was composed of arrays of long, straight, or curved nanorods aligned in 2-D hexagonal arrays. The carbon replica of FDU-1 silica appeared to be composed of ordered arrays of spheres. XRD provided evidence of some degree of ordering of graphene sheets in the carbon frameworks. Elemental analysis showed that the carbons contain an appreciable amount of nitrogen. The use of our novel infiltration method and PAN as a carbon precursor allowed us to obtain ordered mesoporous carbons (OMCs) with (i) very high mesopore volume, (ii) low microporosity, (iii) low secondary mesoporosity, (iv) large pore diameter (8-12 nm), and (v) semi-graphitic framework, which represent a desirable combination of features that has not been realized before for OMCs.