饲料磷酸氢钙中钙的快速测定

饲料级磷酸氢钙中钙,在相应的标准中限定了含量范围,因而测定磷酸氢钙中钙,是饲料级磷酸氢钙质量检验的必检项目.在用EDTA容量法[1]测定钙时,由于大量磷酸根对Ca2+的沉淀效应,致使终点提前,并不断"回头",无法准确地确定终点,严重地影响分析质量.     

电位滴定法快速测定饲料级磷酸氢钙中钙的含量

正磷酸氢钙作为一种添加剂广泛应用于食品、饲料等行业,在饲料加工中作为磷、钙的补充剂[1],可以防治家畜的佝偻病、软骨病及贫血症等各种疾病[2]。饲料级磷酸氢钙中钙的含量是影响动物骨骼能否正常发育的重要指标。传统测定饲料级磷酸氢钙中钙含量的方法主要是乙二胺四乙酸二钠(EDTA)络合滴定法[3],还有电感耦合等离子体原子发射光谱法、高锰酸钾法和一些创新型化学滴定     

同步荧光测定法同时测定盐酸普萘洛尔和盐酸氟桂利嗪

提出了用同步荧光测定法同时测定盐酸普萘洛尔和盐酸氟桂利嗪。试验表明:荧光检测盐酸普萘洛尔的波长宜选定296nm、盐酸氟桂利嗪的波长宜选定263nm、波长差Δλ为50nm条件下进行同步扫描。盐酸普萘洛尔和盐酸氟桂利嗪的质量浓度分别在1.2×10-6～2.8×10-3g.L-1和2.0×10-5～3.6×10-3g.L-1范围内与荧光强度呈线性关系,检出限(3S/N)分别为3.2×10-7g.L-1和6.8×10-6g.L-1。方法用于混合样品中盐酸普萘洛尔与盐酸氟桂利嗪含量的同时测定,回收率在97.5%～101.1%和97.5%～101.7%之间。     

用反相高效液相色谱法测定人体血浆中盐酸氟桂利嗪含量

采用反相高效液相色谱法以桂利嗪为内标测定人体血浆中盐酸氟桂利嗪的含量.以V甲醇:V乙腈:V缓冲液=58:20:22的体系为流动相,用hypersilBDSC8不锈钢色谱柱、紫外检测器(检测波长254nm),血浆样品经乙酸乙酯萃取处理后进样测定.血浆中盐酸氟桂利嗪的含量在5～300μg/L范围内与盐酸氟桂利嗪的峰面积和桂利嗪的峰面积之比呈线性关系(r=0.9997),方法对盐酸氟桂利嗪的平均回收率为83.3%～85.0%,检出限为3μg/L(S/N=3).用该法测定了12名单次口服30mg西比灵(盐酸氟桂利嗪)胶囊的健康志愿者血浆中盐酸氟桂利嗪含量.结果表明,该药在血浆中含量平均达峰时间为(2.67±0.91)h,平均峰质量浓度为(154.9±66.0)μg/L.该法适用于盐酸氟桂利嗪药代动力学的临床监测和研究.     

盐酸超声-氟离子选择电极法测定复合肥中氟含量

为快捷有效地测定复合肥中氟的含量,采用盐酸浸取过夜、盐酸超声、碱熔、纯水煮沸四种方法提取复合肥中的氟离子,用氟离子选择电极进行测定,全程加标回收;结果发现盐酸超声提取法测得值与碱熔提取法测定值非常接近,并且加标回收率为98.4%~104.2%,相对标准偏差为1.9%;则用盐酸超声提取法测定复合肥中的氟含量方法可靠,方便快速,能够满足复合肥中氟含量的测试要求。     

UHPLC测定盐酸氟西汀原料药中甲醛及其测量不确定度评定

采用超快速液相色谱(UHPLC)建立了快速测定盐酸氟西汀原料药中甲醛残留的方法。样品经50%乙腈-水溶液提取,酸性条件下与2,4-二硝基苯肼发生衍生化反应,采用超快速液相色谱仪外标法测定盐酸氟西汀原料药中甲醛的含量,添加量为5～20μg/g时,平均回收率为96.8%～99.0%。评估了测量方法的不确定度。盐酸氟西汀原料药中甲醛含量的测量结果表示为(7.40±0.46)μg/g,k=2。方法适用于盐酸氟西汀中甲醛的快速检测。     

可见分光光度虚拟仪器的研制与应用

LabVIEW是开发虚拟仪器的优秀图形化平台.设计开发了基于LabVIEW8.0的分光光度测量化学虚拟仪器系统,运用于测定饲料级磷酸氢钙中磷的含量,避免了繁琐的人工数据处理和操作的人为误差,实现了数据测量的自动采集、实时显示与处理,提高了测量结果的精度.     

快速测定磷酸氢钙中磷

磷酸氢钙作为一种添加剂广泛应用于食品、饲料等行业,而磷酸氢钙中磷含量的控制非常重要。测定磷含量的方法有比色法、容量法、重量法等。比色法大多适用于低磷样品,容量法适用范围小。磷酸氢钙中磷含量的标准测定方法是采用磷钼酸喹啉重量法,但该方法操作繁琐,而喹钼柠酮试剂不太稳定,需避光保存。有人对滴定法进行改进,提出直接用碱滴定磷酸盐中磷含量,尽管该方法操作简单快速,但用来测定磷酸氢钙中的磷含量时,结果严重偏高。     

蚕茧衍生的氮氟共掺杂碳基催化剂在碱性介质中的氧还原电催化性能的研究

本文通过水热预处理,利用热解工艺从蚕茧中成功的制备了一种高性能的掺杂碳基催化剂. 研究了制备条件及氟原子掺杂对催化剂性能的影响. 在最优化条件下制备出的氮氟共掺杂碳基催化剂具有超过1000 m²•g^-1的比表面积,N元素和F元素含量可达3.5 %及7.3 %. 在碱性条件下,所制备的催化剂具有可与商业铂碳催化剂相媲美的氧还原催化活性,同时展示出优异的抗甲醇中毒性能及稳定性. F原子的掺杂对催化剂性能的提高效果显著.     

氨水介质和氟处理对铝柱层柱粘土性质的影响

 分别在氨介质和钠介质中制备了层柱蒙脱土和层柱累托石,并用氟化铵、氟硅酸铵和氟铝酸铵对层柱粘土进行处理,考察了处理条件对层柱粘土结构和酸性的影响. NH3-TPD和IR分析结果表明,氨介质中制备的层柱粘土比钠介质中制备的具有更强的酸性,经氟处理后层柱粘土的酸性有较大的提高. 氨介质中制备的层柱粘土的低钠含量是其酸性改善的主要原因,而氟处理对层柱粘土酸性的提高主要来自氟对铝柱的表面作用. 氟处理层柱粘土对异丙苯裂解具有很高的催化活性.     

Enhanced uranium bioleaching high-fluorine and low-sulfur uranium ore by a mesophilic acidophilic bacterial consortium with pyrite

The high level of fluorine and low sulfur in the ore could significantly undermine the bioleaching effectiveness. Here, a strategy to improve the bioleaching efficiency by introducing fluoride-resistant mesophilic eosinophils coupled with pyrite supplement was investigated in a bioleaching system with such ore. The results of column and heap bioleaching showed that 89.25% and 90.40% of uranium were recovered with the consortium and pyrite addition, which increased the uranium leaching rates by 13.22% and 8.96% as compared with the sulfuric acid leaching. Hence, it provides a method to improve uranium bioleaching efficiency of the high-fluorine and low-sulfur uranium ore by the consortium adding pyrite.

     

稀土与天青石共伴生矿焙烧及浸出过程研究

稀土与天青石共伴生多金属矿主要由稀土氟碳酸盐和天青石组成,研究了含稀土和锶的混合矿的焙烧及浸出过程,考察了焙烧温度、焙烧时间、浸出初始酸浓度、浸出温度、浸出时间等对浸出率的影响,获得优化的工艺参数为:焙烧温度500℃,焙烧时间2 h,浸出初始酸浓度1.0 mol.L-1,浸出温度35℃,浸出时间1 h,稀土浸出率达95%以上,锶浸出率小于5%,几乎不进入溶液相而保留在固相浸出渣中得以分离和富集。     

Determination of hexavalent and tetravalent uranium in phosphate ores through hydrochloric acid selective leaching

The tetravalent and hexavalent uranium content of three Egyptian phosphate type ore samples namely; Sebayia, Abu Tartur and Qatrani have been studied through selective leaching by hydrochloric acid at normal, oxidized and reduced conditions at an amount of hydrochloric acid less than the stoichiometric value i.e. before phosphoric acid production. Oxidizing condition is attained by incorporating 2% of manganese dioxide in the leaching cycle, whereas reducing condition is attained by adding 2% iron powder. The achieved results show that the amount of tetravalent uranium varies between 5 and 95%. As soon as the achieved stoichiometric value of hydrochloric acid is sufficient to produce phosphoric acid both tetravalent and hexavalent uranium dissolve by virtue of phosphoric acid complexing power for uranium. The chemical form of uranium in the ore determines the type of solvent needed to recover it.     

包头磁尾矿稀土浸出和制备冰晶石的研究

包头白云鄂博矿床产生大量磁尾矿,会产生很大的环境问题。采用纯碱焙烧法对其进行了稀土浸出实验和氟的资源化利用研究。实验结果表明,包头磁尾矿与纯碱混合物于700℃焙烧1.0 h,经稀盐酸洗涤后,以3.0 mol.L-1稀硫酸于65℃下浸出4.0 h,氟的洗脱和稀土浸出效果较好,其中稀土浸出率为97.97%,氟浸出率为99.54%,氟洗脱率为77.32%。以该条件下产生的含氟废水为原料,于90℃下制备了冰晶石,溶液中氟回收率为85.63%,并推算出磁尾矿中氟的总利用率为66.21%。该法使磁尾矿由废弃物变为二次资源成为可能。     

Determination of fluorine by PIGE analysis on bovine tooth enamel treated with bamboo salt SMFP toothpaste and fluoride mouth rinsing solution

The purpose of this study was to evaluate the effectiveness of a toothpaste containing bamboo salt on fluorine uptake in bovine enamel and to compare the efficiency of fluorine uptake between sodium monofluorophosphate (SMFP) toothpaste and sodium fluoride (NaF) mouthrinsing solution using proton induced -ray emission analysis. 30 bovine tooth enamel specimens were prepared and assigned to 5 groups as follows: (a) specimens without any treatment, (b) specimens which were treated with a toothpaste containing dicalcium phosphate dihydrate (DCPD) only, (c) specimens which were treated with a toothpaste containing DCPD and SMFP, (d) specimens which were treated with a toothpaste containing DCPD, SMFP and 2% bamboo salt, (e) specimens which were treated with 0.05% NaF mouthrinsing solution. After 5 and 10 hours of treatment, fluorine concentration was measured at the depth of 263, 625, 2530 nm from the surface of the specimens. The surface concentration of fluorine was markedly increased using SMFP dentifrice. Bamboo salt did not encourage the uptake of fluorine into the enamel surface. NaF mouthrinsing solution showed a considerably higher uptake of fluoride in the intact enamel surface than the SMFP dentifrices.     

Leaching of rubidium from biotite ore by chlorination roasting and ultrasonic enhancement

Aiming at the problems of the low grade of rubidium (Rb) in biotite, and long leaching time and low leaching efficiency of Rb in mica ore, the chlorination roasting-assisted ultrasonic enhanced water leaching method was employed to extract Rb from biotite ore in this study. During the chlorination roasting process, the optimal conditions were obtained, namely roasting temperature 900 °C, roasting time 40 min, and the mass ratio of ore to calcium chloride 1:1, the optimum leaching rate was 96.75 %. Compared with conventional leaching, the ultrasonic field could greatly shorten the leaching time and realize fast and efficient leaching of Rb. The optimal conditions for ultrasonic enhanced leaching were: ultrasonic power 100 W, leaching temperature 60 °C, leaching time 20 min, liquid–solid ratio 4:1, the Rb leaching rate was 98.73 %, which was 40 min shorter than conventional leaching. The particle size and SEM results indicated that the samples by ultrasonic leaching were smaller, no agglomeration phenomenon in a large area, and the surface of the samples was relatively smooth.     

高温热水解-离子色谱法测定铬矿中氟含量

建立了一种快速、准确的离子色谱法测定铬矿中氟含量的方法,将铬矿与石英砂混合,控制氧气和水蒸气的流量,于1 100℃高温下热水解30min,水解液经吸收后,选用Dionex AS11-HC阴离子分析柱,以KOH(20mmol/L)作淋洗液,自动再生抑制型电导检测器检测,离子色谱法测定铬矿中氟的含量。方法的检出限为0.022μg/mL,定量限为0.073μg/mL,方法的检测范围为0.0015%~0.20%,加标回收率在92%~101%。应用于实际样品的测定结果表明,铬矿中氟含量的测定值与标准方法的测定值一致。方法简单快速、检出限低、精密度高、准确度好。能满足铬矿中氟含量的快速准确检测要求。     

Leaching behavior of uranium and vanadium using strong sulfuric acid from Korean black shale ore

The present scientific study focused on leaching behavior of uranium and vanadium from Korean domestic ore. The leaching process experimental conditions optimized for uranium and vanadium metals recovery from Korean domestic ore and developed the basic experimental procedures such as time, particle size, acid influence, temperature effect and pulp density (PD) behavior. Acid influence on leaching process was tested and noted that 2.0 M sulfuric acid concentration is the optimized conditions for present study. The time influence on leaching process was observed and its optimized 2 h for complete leaching process. The temperature influence tested and optimized the 80 °C for complete leaching process and PD is 50 % (wt%). The bench scale experiments developed in a laboratory and tested in pilot level each batch 100 kg of ore sample.     

NH4Cl和HCl溶液浸取电石渣制备多晶型CaCO3

以电石渣为原料,分别以NH4Cl溶液和HCl溶液为浸取剂提取电石渣中的钙,以NH4HCO3为碳化剂制备CaCO3。研究了两种浸取工艺对电石渣中Ca^2+离子提取率的影响,并对两种体系浸取得到的Ca^2+离子提取率、二次残渣量和滤液中的杂质情况,以及制得的CaCO3的产率和性状进行了比较。结果表明,在浸取时间为30 min,浸取剂浓度为2.5 mol·L^-1,pH为8的条件下,以NH4Cl溶液浸取电石渣,加入量按Cl^-/Ca^2+物质的量比为2.0,得到Ca^2+离子提取率为92.87%;以HCl溶液浸取电石渣,加入量按Cl-/Ca^2+物质的量比为2.2,得到Ca^2+离子提取率为98.65%。Ca^2+离子滤液中的主要杂质通过调节pH均可以得到有效控制。NH4Cl溶液浸取电石渣Ca^2+离子提取率略低,二次残渣量高(22.39%),制得CaCO3的产率为1.065 g·g^-1电石渣;HCl溶液浸取电石渣Ca^2+离子提取率高,二次残渣量小(8.87%),制得CaCO3的产率为1.203 g·g^-1电石渣。两种浸取液碳化后制得的CaCO3产品纯度都在99%以上,白度在92.2-97.1%之间,通过控制碳化条件均可制得方解石型、球霰石型和文石型三种晶型的CaCO3。