Determination of Trace Amounts of Palladium(II) by Solid-Phase Spectrophotometry

A simple and sensitive method for solid-phase spectrophotometric determination of palladium(II) at µgL^–1 level based on the reaction product of Pd²⁺ with disodium 1-nitroso-2-hydroxynaphthalene-3,6-disulphonate (Nitroso R salt) previously immobilized on Dowex 1×1 anion exchanger has been developed. The experimental factors (wavelength, pH, amount of resin, concentration of Pd²⁺ solution, volume of solution sample, equilibration time) were optimized. The advantages of this procedure as opposed to solution methods are discussed. The results obtained with synthetic solutions clearly indicate the suitability of the proposed method for real samples analysis.     

Highly Sensitive Spectrofluorimetric Determination of Trace Amounts of Superoxide Dismutase Using a Prulifloxacin-Terbium(III) Probe

Abstract

A new spectrofluorimetric method was developed for determining superoxide dismutase. The interactions between prulifloxacin (PUFX) –Tb³⁺ complex and superoxide dismutase had been studied by using UV-Vis absorption and fluorescence spectra. Using prulifloxacin–Tb³⁺ as a fluorescence probe, under optimum conditions, superoxide dismutase could remarkably enhance the fluorescence intensity of the prulifloxacin–Tb³⁺ complex at λ = 545 nm, and the enhanced fluorescence intensity was in proportion to the concentration of superoxide dismutase. Optimum conditions for the determination of superoxide dismutase were also investigated. The dynamic range for the determination of superoxide dismutase was 0.032 to 22.56 µg mL^?1, and the detection limit (S/N = 3) was 1.5 ng 4 mL^?1. This method was simple, practical, and relatively free of interference from coexisting substances and could be successfully used to determine superoxide dismutase in the plant and blood samples. The mechanism of fluorescence enhancement of prulifloxacin–Tb³⁺ complex by superoxide dismutase was also discussed.     

2-(2-喹啉偶氮)-1,5-二氨基苯固相萃取光度法测定痕量钯

根据2-(2-喹啉偶氮)-1,5-二氨基苯(QADAB)与钯的显色反应及MCI-GEL反相固相萃取小柱对显色络合物的固相萃取,建立了一种测定痕量钯的方法.在0.2～3.0 mol·L-1高氯酸介质中,溴化十六烷基三甲胺(CTMAB)存在下,QADAB与钯反应生成2:1稳定络合物,该络合物可被MCI-GEL反相固相萃取小柱萃取富集,富集的络合物用丙酮洗脱后用光度法测定,在丙酮介质中体系的最大吸收波长为600 nm,表观摩尔吸光率为9.63×104L·mol-1·cm-1.钯质量浓度在0.01～L 5 mg·L-1内符合比耳定律,方法用于几种实样中痕量钯的测定,测得回收率在86%～96%间.     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.     

Construction of Modified Carbon Paste Electrode for Highly Sensitive Simultaneous Electrochemical Determination of Trace Amounts of Copper (II) and Cadmium (II)

A chemically modified electrode was constructed for rapid, simple, accurate, selective and highly sensitive simultaneous determination of Cu(II) and Cd(II) using square wave anodic stripping voltammetry. The electrode was prepared by incorporation of SiO₂ nanoparticles, coated with a newly synthesized Schiff base, in carbon paste electrode. The limit of detection was found to be 0.28 ng mL^?1 and 0.54 ng mL^?1 for Cu(II) and Cd(II), respectively. The proposed chemically modified electrode was used for the determination of copper and cadmium in several foodstuffs and water samples.     

Highly Sensitive Spectrofluorimetric Determination of Trace Amounts of Folic Acid using a Oxytetracycline-Terbium(III) Probe

Abstract

A new spectrofluorimetric method was developed for the determination of trace amounts of folic acid using oxytetracycline–terbium ion complex as a fluorescent probe. In the buffer solution of pH 6.00, folic acid remarkably reduced the fluorescence intensity of the oxytetracycline–terbium complex at λ = 545 nm. The reduced fluorescence intensity of the Tb³⁺ ion was proportional to the concentration of folic acid. Optimum conditions for the determination of folic acid were investigated. This method was simple, practical, and relatively free of interference from coexisting substances. Furthermore, it was successfully applied to assess folic acid in tablet, injection, and urine samples.     

2-Methyl-1, 4-Naphthoquinone Thiosemicarbazone as a Sensitive and Selective Chromogenic Reagent for Microdetermination of Palladium (II)

A simple, sensitive and selective procedure has been developed for the spectrophotometric determination of palladium. Palladium (II) reacts with 2-methyl-1,4-naphthoquinone thiosemicarbazone to form an orange brown complex in the pH range 8.2–9.5. The sensitivity, in terms of Sandell's definition, is 0.0025 μg Pd/cm² at 500 nm. The system adheres to Beer's law upto 2.66 ppm of palladium and optimum concentration range for the determination of the metal is 0.3–2.29 ppm with molar absorbtivity of 4.2×10⁴ ? mole^?1 cm^?1. The complex has 1:1 molar composition, as deduced by Job's method. The determination of palladium has been carried out in presence of foreign ions especially in presence of eighth group metals.     

催化反应-示波极谱法测定痕量钒

在硫酸介质及100℃水浴加热条件下,钒(Ⅴ)对过硫酸铵氧化二苯羟乙酸生成二苯甲酮这一慢反应具有强烈的催化作用,据此拟定了一个测定8.0～100ng/ml钒的催化反应-示波极谱法,并用于测定铝合金及纯铝中钒的含量。     

流动注射化学发光法测定痕量硫

基于硫离子对鲁米诺－过氧化氢化学发光反应的增敏作用,建立了测定痕量硫的流动注射化学发光反应的增敏作用,建立了测定痕量硫的流动注射化学发光的新方法。该方法的线性范围为２．０×１０－９～８．０×１０－７ｇ／ｍＬ,检出限为５．６×１０－１０ｇ／ｍＬ,相对标准偏差小于５％（１．０×１０－７ｇ／ｍＬＳ２－,ｎ＝１１）。方法简单,快速,灵敏,已用于环境水样中痕量硫的测定。     

间羧基偶氮羧光度法测定痕量铬的研究

研究了间羧基偶氮羧与Cr2 O2 -7的褪色反应 ,建立了一种新的测定痕量Cr(VI)的光度方法 .发现其在高氯酸介质中具有高灵敏的褪色反应 ,摩尔吸收系数达到 3 .5× 10 6L/mol·cmCr(VI)量在 0～ 48μg范围内符合比尔定律     

4, 5-二溴苯基荧光酮光度法测定微量钯

研究了在十二烷基磺酸钠存在下,Pd(Ⅱ)与4,5 二溴苯基荧光酮的显色反应.试验表明,在pH6 3醋酸 醋酸钠缓冲溶液中,Pd(Ⅱ)与试剂形成1∶4的暗黄色配合物,配合物的最大吸收峰位于376nm波长处,表观摩尔吸光系数ε为1 06×105L/(mol·cm).Pd(Ⅱ)含量在0～12μg/10mL范围内符合比尔定律.所拟方法用于钯催化剂和钯矿样中微量钯的测定,结果满意.     

A New Spectrophotometric Method for Determination of Microgram Amounts of Iron (II) in Pharmaceuticals

Abstract

A new spectrophotometric method was developed for the assay of 0–6 mg/1 of iron (II) in a number of certified Iraqi drugs. The Sandell index is 0.07 μg cm^2- and the ? max is 6000 1 mol^?1 cm^?1. An interference study is also described.     

异丙醇—ClO^——H2O2化学发光体系测定痕量乙醛的研究

C1O~--H_2O_2可强烈氧化某些有机物而发光,碱性介质中的异丙醇也可被ClO~--H_2O_2氧化产生化学发光,乙醛的存在可显著增强该体系的化学发光效果,且被敏化的化学发光强度与一定范围内的乙醛浓度有良好的线性关系,依据上述关系,我们建立了用于测定痕量乙醛的新方法,该法具有较高的灵敏度,检出限为1.0×10~(-10)g/mL乙醛,线性响应范围大于3个数量级,将此法应用于测定有机化工厂废水中的乙醛,结果满意。     

Determination of Trace Amounts of Acetaldehyde Using a Novel Chemiluminescence Reaction

Abstract

The chemiluminescent reaction of iso-propyl alcohol with C10^?-H₂O₂ is enhanced by acetaldehyde. This provides a new method for the determination of trace amounts of acetaldehyde. The detection limit is 0.08ng/ml acetaldehyde and the linear dynamic range is 0.5ng/ml to 1000 ng/ml. The method results in good selectivity and has been satisfactorily applied to the determination of traces of acetaldehyde in waste water samples.     

Isonitroso-4-Methyl-2-Pentanone for Solvent Extraction and Spectrophotometric Determination of Palladium (II) at Trace Level

Abstract

Isonitroso-4-methyl-2-pentanone (HIMP) is proposed as a new reagent for extraction and photometric determination of Pd(II). The reagent forms a yellow complex with palladium in the pH range 4.0-5.0. The complex extracted into chloroform was measured at 330 nm. The molar absorptivity was found to be 5.37 × 10³ 1 mol^?1 cm^?1 and Sandell's sensitivity 20 ng cm^?2 Beer's law was obeyed over the concentration range 0.1-10.0 μg/ml of palladium. The method is applicable for palladium estimation in Ores and catalysts.     

Simultaneous Determination of Copper (II) and Mercury (II) by Using a Zero-Crossing Method

Abstract

The application of a zero-crossing method to the simultaneous determination of copper (II) and mercury (II) with methylethylenediaminetetraacetic acid (MEDTA) is described. The procedure does not require equations to be solved, and it is suitable for concentrations of 0.008–0.036 mg ml^?1 of copper and 0.025–0.300 mg ml^?1 of mercury. The main interferences, both anionic and cationic, were easily eliminated. The method was applied to different aqueous matrices. It was compared with an atomic absorption spectrophotometry method (AA) and good results were obtained.     

Non-Extractive Simultaneous Spectrophotometric Determination of Trace Quantities of Palladium(II) and Tungsten(VI)

A second order derivative spectrophotometric method has been developed for the simultaneous determination of Palladium(II) and Tungsten(VI) using 3,4-dihydroxybenzaldehyde isonicotinoylhydrazone (3,4-DHBINH) as a new complexing agent. The Pd(II) reacts with 3,4-DHBINH in the pH range from 3 to 7 to form green colored solution. The absorbance calibration curves were constructed for palladium(II) at 362 nm (0.53～6.40 μg/ml) and tungsten(VI) at 374 nm (0.92～11.40 μg/ml). The metal ions interfere with each other in determination of zero order as well as the first order spectrophotometry. The optimum condition for maximum color development and other analytical parameters were evaluated. The method was applied successfully for the determination of palladium in hydrogenation catalyst and tungsten in industrial waste water samples.     

Spectrophotometric Determination of Palladium(II) with n-Hydroxy-N,N-Diphenylbenzamidine and 1 -(2-Pyridylazo)-2-Naphthol

A spectrophotometric method to determine palladium(II) at trace levels is based on the extraction of palladium(II) as a binary complex with N-hydroxy-N,N′-diphenylbenzamidine (HDPBA) in chloroform at pH 5.0 ± 0.2. The complex shows maximum absorbance at 400 nm with molar absorptivity 6.4 × 10³ L mol^?1 cm^?1. The sensitivity of the Pd(II)-HDPBA complex was enhanced by the addition of l-(2-pyridylazo)-2-naphthol (PAN). The green coloured complex shows maximum absorbance at 620 nm with molar absorptivity 1.58 × 10⁴ L mol^?1 cm^?1. Sandell's sensitivity and the detection limit of the method are 0.0067 μg cm^?2and 0.1 μg Pd(II) mL^?1, respectively. Most common metal ions associated with palladium metal do not interfere. The effects of various analytical parameters on the extraction of the metal are discussed.