Piezoelectric properties of oriented films of poly(γ-methyl D-glutamate)

The dynamic piezoelectric stress constant e^*₂₅ of drawn films of poly(γ-methyl D -glutamate) (PMDG) cast from solutions in α-helix-promoting solvents 1,2-dichloroethane (DCE) and chloroform and from the nonhelicogenic solvent dichloroacetic acid (DCA) was measured from ?180°C to 200°C at 110 Hz. The drawn and annealed films cast from chloroform show a small peak for the real part of piezoelectric stress constant ?e′₂₅ in the temperature range of the mechanical α₂-crystalline relaxation, which is caused by the distortion motion of the backbone chain of the α-helix. On the other hand, drawn films cast from DCE show the peak of the real part of the piezoelectric stress constant, whose magnitude decreases in the range of the mechanical α₁-crystalline relaxation or the β-relaxation processes, which were previously ascribed, respectively, to mutual slipping of α-helices and to the micro-Brownian motion of disordered regions. Also, ?e′₂₅ becomes virtually zero near 180°C where the α₂-relaxation is located. These results suggest that the polarization change induced by applied strain is caused by distortion of the backbone chains in the α-helix. Near 0°C, the temperature range of the side-chain mechanical relaxation, ?e′₂₅ exhibits a marked peak both for films cast from chloroform and from DCE. The maximum value of ?e′₂₅ and the orientation function of the α-helix axis are linearly related and extrapolation of ?e′_25,max to unit orientation function gives 1.3 × 10⁴ cgs esu which corresponds to 2.4 Debye per residue. This value corresponds reasonably to the value of 3.71 Debye for the permanent dipole moment of NHCO bond if the correction for crystallinity is made. This result also indicates the piezoelectric properties of PMDG arise from distortion of the backbone chain of the α-helix induced by applied strain.     

Orientation and structural development of semicrystalline poly(lactic acid) under uniaxial drawing assessed by infrared spectroscopy and X-ray diffraction

The effects of drawing temperature (T_d) and draw strain on the orientation and structure of semicrystalline poly(lactic acid) (PLA) films were investigated by wide angle X-ray diffraction and polarized Fourier transform infrared spectroscopy. Semicrystalline PLA samples with two initial levels of crystallinity, X_c = 1% and 11%, were prepared by cold crystallization at 80 ^°C. Whatever X_c and T_d, the total amount of the ordered phases (i.e. crystalline + mesophase) increased with draw strain, which could be ascribed to the formation of strain-induced mesophase at T_d = 60 or 70 ^°C but crystalline at 80 ^°C. Also, the molecular orientation of both the amorphous and ordered phases increased with draw strain. Whatever X_c, the orientation of the ordered phases was insensitive to T_d, whereas higher orientation in the amorphous phase was achieved at lower T_d, and the trend was more significant for X_c = 1% compared with 11%.     

Structure and Bonding of the Mixed‐Valent Platinum Trihalides,PtCl3 and PtBr3

The isotypical crystal structures of the mixed valent trihalides PtCl₃ and PtBr₃ were redetermined by single crystal methods (space group R3¯; trigonal setting; PtCl₃: a = 21.213Å, c = 8.600Å, c/a = 0.4054; Z = 36; 1719 hkl; R = 0.035; PtBr₃: a = 22.318Å, c = 9.034Å; c/a = 0.4048; Z = 36; 1606 hkl; R = 0.027). A cubic closest packing of X^— anions forms the basis of an optimized arrangement of cuboctahedrally [Pt₆X₁₂] cluster molecules with Pt^II and enantiomers of helical chains of edge‐condensed [PtX₂X_4/2] octahedra with Pt^IV in cis‐Δ‐ and cis‐Λ‐configuration, respectively. The bond lengths vary with the function of the X^— ligands (d¯(Pt^II—X) = 2.315 and 2.445Å; d¯(Pt^II—Pt^II) = 3.336 and 3.492Å; d(Pt^IV—X) = 2.286 — 2.417Å and 2.437 — 2.563Å). The Pt^II atoms are shifted outwards the X₁₂ cuboctahedra by 0.045Å and 0.024Å, respectively. The symmetry governed Periodic Nodal Surface, PNS, perfectly separates the regions of different valencies. Quantum chemical calculations exclude the possible additional interactions between Pt^II and one of the exo‐ligands of Pt^IV.     

Oriented crystallization of poly(L‐lactic acid) in uniaxially oriented blends with poly(vinylidene fluoride)

This article describes the oriented crystallization of poly(L ‐lactic acid) (PLLA) in uniaxially oriented blends with poly(vinylidene fluoride) (PVDF). Uniaxially drawn films of PLLA/PVDF blend with fixed ends were heat‐treated in two ways to crystallize PLLA in oriented blend films. The crystal orientation of PLLA depended upon the heat‐treatment process. The crystal c‐axis of the α form crystal of PLLA was highly oriented in the drawing direction in a sample cold‐crystallized at T_c = 120 °C, whereas the tilt‐orientation of the [200]/ [110] axes of PLLA was induced in the sample crystallized at T_c = 120 °C after preheating at T_p = 164.5–168.5 °C. Detailed analysis of the wide‐angle X‐ray diffraction (WAXD) indicated that the [020]/ [310] crystal axes were oriented parallel to the drawing direction, which causes the tilt‐orientation of the [200]/ [110] axes and other crystal axes. Scanning electron microscopy (SEM) suggested that oriented crystallization occurs in the stretched domains of PLLA with diameters of 0.5–2.0 μm in the uniaxially drawn films of PVDF/PLLA = 90/10 blend. Although the mechanism for the oriented crystallization of PLLA was not clear, a possibility was heteroepitaxy of the [200]/[110] axes of the α form crystal of PLLA along the [201]/[111] axes of the β form crystal of PVDF that is induced by lattice matching of d₁₀₀(PLLA) ≈ 5d₂₀₁(PVDF). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1376–1389, 2008     

Synthesis and properties of phosphorus containing polyester‐amides derived from 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene

A series of polyester‐amides that contain phosphorus were synthesized by low temperature solution condensation of 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene (III) with various aromatic acid chlorides in N‐methyl pyrrolidone (NMP). All polyester‐amides are amorphous and readily soluble in many organic solvents such as dimethylacetamide (DMAc), NMP, dimethylsulfoxide, and dimethylformamide at room temperature or on heating. Light yellow and flexible films of these polyester‐amides could be cast from the DMAc solutions. The polymers with an inherent viscosity of 0.26–0.72 dL/g were obtained in quantitative yields. These polyester‐amides have good mechanical properties (G′ of ∼ 10⁹ Pa up to 200°C) and good thermal and flame retardant properties. The glass transition temperatures of these polyester‐amides ranged from 250 to 273°C. The degradation temperatures (T_d 5%) in nitrogen ranged from 466 to 478°C and the char yields at 800°C were 59.6–65.2%. The limiting oxygen indexes of these polyester‐amides ranged from 35 to 43. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 891–899, 1999     

Piezoelectric relaxation in poly(γ-benzyl-glutamate)

The piezoelectric d- and e-constants, together with the elastic constant and the dielectric constant, were measured for oriented poly(γ-benzyl-glutamate) (PBG) films with various elongation ratios as a function of frequency and temperature, using an apparatus developed by us. The results are discussed in terms of a general theory of piezoelectricity for inhomogeneous systems, in particular for a disperse two-phase system. The piezoelectricity of PBG film is proved to originate from the piezoelectric and optically active symmetry of PBG crystallities and their orientation distribution by three findings: (1) the d₁₄ component of the piezoelectric matrix, which is the only component for a uniaxially or uniplanarly oriented system, is observed; (2) d₁₄ > 0 for PBDG and d₁₄ < 0 for PBLG; (3) d₁₄ is proportional to the degree of orientation F_c of PBG crystallites, as determined by x-ray diffraction. By extrapolating to perfect orientation, d₁₄ is determined to be 5 × 10^?8 cgs esu, if the side chains of PBG are rigid. The piezoelectric relaxation of PBG due to thermal motion of the side chains has a dual character: it is relaxational at lower frequencies and retardational at higher frequencies. On the assumption that the α-helical main chains surrounded by the bulky side chains are responsible for the origin of the piezoelectricity, such relaxation phenomena are interpreted in terms of the relaxation of the local elastic field in the main chains. An equivalent model having the same frequency characteristics is proposed to include the higher order structure of the PBG film.     

The influence of film thickness and process temperature on <Emphasis Type="Italic">c</Emphasis>-axis orientation of Bi<Subscript>3</Subscript>TiTaO<Subscript>9</Subscript> thin films

Bi-layered ferroelectric Bi₃TiTaO₉ (BTT) thin films with different thickness (ranging from 100 to 400 nm) were successfully fabricated on Pt(111)/TiO₂/SiO₂/(100)Si substrates using chemical solution deposition (CSD) technique at different annealing temperatures. The c-axis orientation of the films was affected by film thickness and process temperature. The thinner the film and the higher the process temperature, the higher the c-axis orientation. With the increase of film thickness, the stress decreased but the film roughness increased, which led to the decrease of c-axis orientation of films. BTT films annealed at 800°C were found to have much improved remament polarization (P _r ) than that of films annealed at 650 and 750°C. The P _r and coercive field (E _c ) values were measured to be 2 μC/cm² and 100 kV/cm, respectively. BTT films showed well-defined ferroelectric properties with grain size larger than 100 nm.     

New technique of processing highly oriented poly(vinylidene fluoride) films exclusively in the β phase

Oriented β‐phase films were obtained by utilizing two different techniques: conventional uniaxial drawing at 80 °C of predominantly α‐phase films, and by drawing almost exclusively β‐phase films obtained by crystallization at 60 °C from dimethylformamide (DMF) solution with subsequent pressing. Wide angle X‐ray diffraction (WAXD) and pole figure plots showed that with the conventional drawing technique films oriented at a ratio (R) of 5 still contained about 20% of phase α, a crystallinity degree of 40% and β‐phase crystallographic c ‐axis orientation factor of 0.655. Drawing at 90 °C and with R = 4 of originally β‐phase films results in exclusively β‐phase films with crystallinity degree of 45% and orientation factor of 0.885. Crystalline phase, crystallinity degree, and crystallographic c‐axis orientation factor of both phases were also determined for α‐phase oriented films obtained by drawing α‐phase films at 140 °C. For films drawn at 140 °C the α to β phase transition drops to about 22%. Reduction in crystallinity degree with increasing R is more pronounced at draw temperature of 140 °C compared with 80 °C. Moreover, for both phases the c ‐axis orientation parallel to the draw direction is higher at draw temperature of 140 °C than at 80 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2793–2801, 2007     

Five N′‐benzylidene‐N‐methylpyrazine‐2‐carbohydrazides

The compounds N′‐benzylidene‐N‐methylpyrazine‐2‐carbohydrazide, C₁₃H₁₂N₄O, (IIa), N′‐(2‐methoxybenzylidene)‐N‐methylpyrazine‐2‐carbohydrazide, C₁₄H₁₄N₄O₂, (IIb), N′‐(4‐cyanobenzylidene)‐N‐methylpyrazine‐2‐carbohydrazide dihydrate, C₁₄H₁₁N₅O·2H₂O, (IIc), N‐methyl‐N′‐(2‐nitrobenzylidene)pyrazine‐2‐carbohydrazide, C₁₃H₁₁N₅O₃, (IId), and N‐methyl‐N′‐(4‐nitrobenzylidene)pyrazine‐2‐carbohydrazide, C₁₃H₁₁N₅O₃, (IIe), have dihedral angles between the pyrazine rings and the benzene rings in the range 55–78°. These methylated pyrazine‐2‐carbohydrazides have supramolecular structures which are formed by weak C—H...O/N hydrogen bonds, with the exception of (IIc) which is hydrated. There are π–π stacking interactions in all five compounds. Three of these structures are compared with their nonmethylated counterparts, which have dihedral angles between the pyrazine rings and the benzene rings in the range 0–6°.     

Changes in superstructure and mechanical properties of poly(ethylene‐2,6‐naphthalate) fibers with critical necking tension

Poly(ethylene‐2,6‐naphthalate) fibers were zone‐drawn under a critical necking tension (σ_c) defined as the minimum tension needed to generate a necking at a given drawing temperature (T_d). In the zone drawing under σ_c, the neck was observed from 110 to 160 °C. The superstructure in a neck zone induced at each T_d was studied. The σ_c value decreased exponentially with increasing T_d and dropped to a low level at a higher T_d. The draw ratio increased rapidly with T_d increasing above 90 °C, but the birefringence and degree of crystallinity decreased gradually. To study the molecular orientation in the neck zone, we measured a dichroic ratio (A_‖/A_?) of a C? O band at 1256 cm^?1 along a drawing direction in the neck zone with a Fourier transform infrared microscope. A_‖/A_? at T_d = 110 °C increased rapidly in the narrow neck zone, and that at T_d = 140 °C increased in the edge of the wide neck zone. Wide‐angle X‐ray diffraction patterns of the fibers obtained at T_d = 130 °C and lower showed three reflections due to an α form, but those at T_d = 140 and 150 °C had reflections due to the α form and a β form. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1629–1637, 2001     

Synthesen,Kristallstrukturen und Drillingsbildung der Cluster‐Trimere Bi2[PtBi6Br12]3 und Bi2[PtBi6I12]3

Syntheses, Crystal Structures, and Triple Twinning of the Cluster Trimers Bi₂[PtBi₆Br₁₂]₃ and Bi₂[PtBi₆I₁₂]₃ Melting reactions of Bi with Pt and BiX₃ (X = Br, I) yield shiny black, air insensitive crystals of the subhalides Bi₂[PtBi₆X₁₂]. Bi₂[PtBi₆Br₁₂]₃ crystallizes in the monoclinic space group C2/m with lattice parameters a = 1617.6(2) pm, b = 1488.5(1) pm, c = 1752.4(2) pm, and β = 110.85(4)°. Bi₂[PtBi₆I₁₂]₃ adopts the triclinic space group with pseudo‐monoclinic lattice parameters a = 1711.2(2) pm, b = 1585.1(1) pm, c = 1865.7(2) pm, and α = 90°, β = 111.15(4)°, γ = 90°. The two homoeotypic compounds consist of cuboctahedral [Pt^?IIBi^II₆X^?I₁₂]^2? clusters that are concatenated into linear trimers by Bi^III atoms. The ordered distribution of Bi^III atoms destroys the inherent threefold rotation axes in the packing of cluster anions. As a consequence of the pseudosymmetry the crystals are triple twinned along [201]. Due to different orientations of the cluster trimers there are two Bi^II···X inter‐cluster bridges per Bi^II atom in Bi₂[PtBi₆Br₁₂]₃ but only one bridge in Bi₂[PtBi₆I₁₂]₃. The structure of the iodine compound can be deduced from the NaCl structure type, leaving 37 of 96 atomic positions unoccupied. The arrangement of the cuboctahedral clusters follows the motif of a body‐centered cubic packing.     

Electrochemical Characterization of Myoglobin‐Polylysine Films at a Temperature Range of 6–80 °C

This work demonstrated for the first time that myoglobin cross‐linked in polylysine films is electrochemically active at 6 °C. At 6 °C, these protein films exhibited reversible reduction/oxidation peaks which are characteristic of Fe^III/Fe^II redox couple. The estimated current function densities (J=1.6×10^?4 C/V cm²), surface concentrations (Γ_T=0.10 nmol/cm²) and standard electron transfer constant (k_s=13.86 s^?1) at 6 °C for the data taken at a scan rate of 0.1 V/s were similar to those which were obtained at 10, 15 and 23 °C. Basically, this study shows a possible electrocatalytic application of these myoglobin/polylysine films, for example in low temperature sensing applications.     

The Thermal Expansion of Wood Cellulose Crystals

We have investigated tension wood cellulose obtained from Populus maximowiczii using X-ray diffraction at temperatures from room temperature to 250 °C. Three equatorial and one meridional d-spacings showed a gradual linear increase with increasing temperature. For temperatures above 180 °C, however, the equatorial d-spacing increased dramatically. Thus, the linear and volume thermal expansion coefficients (TECs) below 180 °C were determined from the d-spacings. The linear TECs of the a-, b-, and c-axes were: α _a = 13.6 × 10⁻⁵ °C⁻¹, α _b = −3.0× 10⁻⁵ °C⁻¹, and α _c =0.6× 10⁻⁵ °C⁻¹, respectively, and the volume TEC was β = 11.1× 10⁻⁵ °C⁻¹. The anisotropic thermal expansion in the three coordinate directions was closely related to the crystal structure of the wood cellulose, and it governed the macroscopic thermal behavior of solid wood.     

Influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films

The influence of pyrolysis temperature on the properties of sol–gel derived zinc oxide films has been investigated. As-deposited films were pyrolyzed at 300 °C for 30 min and at 500 °C for 10 min. Final annealing was done at 600 °C for 30 min in air. The as-grown films deposited on soda-lime-silica glass substrates were highly c-axis oriented. Distinct grain structure was present in the film pyrolyzed at 500 °C, while the surface of the film pyrolyzed at 300 °C was smooth and no observed texture. The surface of ZnO pyrolyzed at 300 °C was covered with needle-like grain growth. With increasing pyrolysis temperature at 500 °C, a three-dimensional island formation was appeared.     

Crystal Structure of the Mixed‐Valent Basic Mercury Nitrate HgI2(NO3)2·HgII(OH)(NO3)·HgII(NO3)2·4HgIIO [= Hg8O4(OH)(NO3)5]

Light‐yellow single crystals of the mixed‐valent mercury‐rich basic nitrate Hg₈O₄(OH)(NO₃)₅ were obtained as a by‐product at 85 °C from a melt consisting of stoichiometric amounts of (Hg^I₂)(NO₃)₂·2H₂O and Hg^II(OH)(NO₃). The title compound, represented by the more detailed formula Hg^I₂(NO₃)₂·Hg^II(OH)(NO₃)·Hg^II(NO₃)₂·4Hg^IIO, exhibits a new structure type (monoclinic, C2/c, Z = 4, a = 6.7708(7), b = 11.6692(11), c = 24.492(2) Å, β = 96.851(2)°, 2920 structure factors, 178 parameters, R1[F² > 2σ(F²)] = 0.0316) and is made up of almost linear [O‐Hg^II‐O] and [O‐Hg^I‐Hg^I‐O] building blocks with typical Hg^II‐O distances around 2.06Å and a Hg^I‐O distance of 2.13Å. The Hg₂²⁺ dumbbell exhibits a characteristic Hg‐Hg distance of 2.5079(7) Å. The different types of mercury‐oxygen units form a complex three‐dimensional network exhibiting large cavities which are occupied by the nitrate groups. The NO₃^? anions show only weak interactions between the nitrate oxygen atoms and the mercury atoms which are at distances > 2.6Å from one another. One of the three crystallographically independent nitrate groups is disordered.     

Thermal expansion of the crystal lattice of novel thermoplastic polyimides

Measurements of the coefficient of thermal expansion (CTE) of the crystalline lattice of two semicrystalline thermoplastic polyimides are reported. NEW-TPI and LARC-CPI polyimides were studied using elevated temperature wide-angle x-ray scattering (WAXS) from 25°C. To 325°C. To examine possible shifts in the c-axis, a novel approach developed in our lab was used to create highly oriented samples. Films were treated in 1-methyl-2-pyrrolidinone (NMP) at the reflux temperature, washed and then dried under constraint. The films treated in this manner were highly oriented, with c-axes preferentially aligned along the film normal. The advantage of this orientation is that it allows numerous reflections of type (00l) to be examined for temperature shifts of the c-axis using reflection mode WAXS. No systematic shift of the c-axis lattice parameter as a function of temperature was observed in either NEW-TPI or LARC-CPI. The c-axis thermal expansion is concluded to be smaller than 8 x 10^?6/°C for LARC-CPI, and for NEW-TPI may be weakly negative. From WAXS of unoriented films, systematic shifts in the a and b lattice parameters were deduced as a function of temperature. The linear CTEs relating these unit cell parameters at temperature T to their values at 0°C are: ©1995 John Wiley & Sons, Inc.     

Mechanism and kinetics of the imidazolidinone nitroxide‐mediated free‐radical polymerization of styrene

Styrene radical polymerizations mediated by the imidazolidinone nitroxides 2,5‐bis(spirocyclohexyl)‐3‐methylimidazolidin‐4‐one‐1‐oxyl (NO88Me) and 2,5‐bis(spirocyclohexyl)‐3‐benzylimidazolidin‐4‐one‐1‐oxyl (NO88Bn) were investigated. Polymeric alkoxyamine (PS‐NO88Bn)‐initiated systems exhibited controlled/living characteristics at 100–120 °C but not at 80 °C. All systems exhibited rates of polymerization similar to those of thermal polymerization, with the exception of the PS‐NO88Bn system at 80 °C, which polymerized twice as quickly. The dissociation rate constants (k_d) for the PS‐NO88Me and PS‐NO88Bn coupling products were determined by electron spin resonance at 50–100 °C. The equilibrium constants were estimated to be 9.01 × 10^?11 and 6.47 × 10^?11 mol L^?1 at 120 °C for NO88Me and NO88Bn, respectively, resulting in the combination rate constants (k_c) 2.77 × 10⁶ (NO88Me) and 2.07 × 10⁶ L mol^?1 s^?1 (NO88Bn). The similar polymerization results and kinetic parameters for NO88Me and NO88Bn indicated the absence of any 3‐N‐transannular effect by the benzyl substituent relative to the methyl substituent. The values of k_d and k_c were 4–8 and 25–33 times lower, respectively, than the reported values for PS‐TEMPO at 120 °C, indicating that the 2,5‐spirodicyclohexyl rings have a more profound effect on the combination reaction rather than the dissociation reaction. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 327–334, 2003     

The microstructure and magnetic properties of Ni<Subscript>0.4</Subscript>Zn<Subscript>0.6</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> films prepared by spin-coating method

Nickel zinc ferrite (Ni_0.4Zn_0.6Fe₂O₄) films on Si (100) substrate were synthesized using a spin-coating method. The crystallinity of the Ni_0.4Zn_0.6Fe₂O₄ films with the thickness of about 386 nm became better as the annealing temperature increased. The films have smooth surface, relatively good packing density and uniform thickness. The volatilization of Zn is serious at 900 °C. With the increase of annealing temperature, the saturation magnetization M _s increases in the temperature ranging from 400 to 700 °C, however, decreases above 700 °C, and the coercivity H _c increases in the temperature range 400–800 °C, decreases above 800 °C. After annealed at 700 °C for 2 h in air with the heating rate 2 °C/min, the film shows a maximum saturation magnetization M _s of 349 emu/cc and low coercivity H _c of 66 Oe. The M _s is higher than others which prepared by this method, however, the H _c is lower. The M _s of Ni_0.4Zn_0.6Fe₂O₄ films annealed at 700 °C increases with increasing annealing time and the H _c changes slightly.     

Micellization to gelation of a triblock copolymer in water: Thermoreversibility and scaling

Aqueous solutions of a poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) triblock copolymer, Pluronic F108 (PEO₁₃₃PPO₅₀PEO₁₃₃), ranging from 1 to 35 wt %, were studied with differential scanning microcalorimetry and rheology. The thermoreversible micellization and gelation were examined through a heating process and a subsequent cooling process at a fixed rate of 1 °C/min. The critical micellization temperature (CMT), determined by the onset temperature of the endothermic peak in the heating process, was a decreasing function of the F108 concentration. A small secondary endothermic peak appeared only when the polymer concentration was 22.5 wt % or higher, indicating that there was a sol–gel transition but that the gelation was a nearly athermic process. Upon heating, an abrupt increase was observed in both the dynamic storage modulus (G′) and dynamic loss modulus (G″) within a narrow temperature range. T_G′, the temperature for the transition in G′, was a linear decreasing function of the polymer concentration and different from CMT. T_G′ tended to approach CMT with an increasing F108 concentration. Beyond this transition, G′ reached a plateau, and the plateau increased in height and broadened with the polymer concentration. The value of G′ at 70 °C (G′₇₀) could be approximately scaled with concentration c by G′₇₀ ∝ c^7.3. In addition, the definition for a gel to obey G′ > G″ was valid only when c was greater than 22.5 wt %, and this was in agreement with the secondary endothermic peak found with differential scanning calorimetry. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2014–2025, 2004     

Bis{2‐[(phenylimino)ethyl]‐1H‐pyrrol‐1‐ido‐κ2N,N′}nickel(II): a supramolecular structure formed by C—H...π hydrogen bonds

In the title compound, [Ni(C₁₂H₁₁N₂)₂], the Ni^II cation lies on an inversion centre and has a square‐planar coordination geometry. This transition metal complex is composed of two deprotonated N,N′‐bidentate 2‐[(phenylimino)ethyl]‐1H‐pyrrol‐1‐ide ligands around a central Ni^II cation, with the pyrrolide rings and imine groups lying trans to each other. The Ni—N bond lengths range from 1.894 (3) to 1.939 (2) Å and the bite angle is 83.13 (11)°. The Ni—N(pyrrolide) bond is substantially shorter than the Ni—N(imino) bond. The planes of the phenyl rings make a dihedral angle of 78.79 (9)° with respect to the central NiN₄ plane. The molecules are linked into simple chains by an intermolecular C—H...π interaction involving a phenyl β‐C atom as donor. Intramolecular C—H...π interactions are also present.