AlGaN/GaN异质结Ni/Au肖特基表面处理及退火研究

采用O₂等离子体及HF溶液对AlGaN/GaN异质结材料进行表面处理后，Ni/Au肖特基接触特性比未处理有了明显改善，反向泄漏电流减小3个数量级.对制备的肖特基接触进行200—600℃ 5min的N₂气氛退火，发现退火冷却后肖特基反向泄漏电流随退火温度增大进一步减小.N₂气中600℃退火后肖特基二极管C-V特性曲线在不同频率下一致性变好，这表明退火中Ni向材料表面扩散减小了表面陷阱密度；C-V特性曲线随退火温度增大向右移动，从二维电子气耗尽电压绝对值减小反映了肖特基势垒的提高. 关键词： AlGaN/GaN 肖特基接触 表面处理 退火     

牺牲Ni退火对硅衬底GaN基发光二极管p型接触影响的研究

本文通过在硅衬底发光二极管(LED)薄膜p-GaN表面蒸发不同厚度的Ni覆盖层,将其在N₂ ∶O₂=4 ∶1的气氛中、400℃—750℃的温度范围内进行退火,在去掉薄膜表面Ni覆盖层之后制备Pt/p-GaN欧姆接触层.实验结果表明:退火温度和Ni覆盖层厚度均对硅衬底GaN基LED薄膜p型欧姆接触有重要影响,Ni覆盖退火能够显著降低p型层中Mg受主的激活温度.经牺牲Ni退火后,p型比接触电阻率随退火温度的升高呈先变小后变大的规律,随Ni覆盖层厚度的增加呈先变小后变 关键词： 氮化镓 发光二极管 牺牲Ni退火 p型接触     

退火温度和退火气氛对Ni/Au与p-GaN之间欧姆接触性能的影响

研究了不同退火温度和气氛对Ni/Au与p-GaN之间欧姆接触性能的影响. 采用圆形传输线模型方法得到不同退火温度和不同退火气氛下的比接触电阻率. 结果表明, 较适宜的退火温度为500 ℃左右, 退火温度太高或太低都会导致比接触电阻率的增大; 较适宜的退火气氛为适量含氧的氮气气氛, 且氧气含量对比接触电阻率大小的影响并不显著. 经过对退火条件的优化, 得到的比接触电阻率可达7.65×10^-4 Ω·cm². 关键词： p-GaN 欧姆接触 圆形传输线模型 快速热退火     

Ni/Ag/Ti/Au与p-GaN的欧姆接触性能及光反射率

研究了不同Ni厚度的Ni/Ag/Ti/Au电极在不同退火温度和退火气氛下与p-GaN之间的欧姆接触性能以及电极的光反射率的变化.采用矩形传输线模型对各电极的比接触电阻率进行测算,利用分光光度计对电极在不同波长下的反射率进行测量.结果表明,Ni金属层的厚度越小,电极的光反射率越高,而Ni层厚度对比接触电阻率的影响较小;当退火温度高于400℃后,电极的光反射率降低,在氧气氛围中退火后光反射率比在氮气中退火后下降更加明显.但在氧气氛围中退火有利于减小比接触电阻率.综合考虑接触电阻和光反射率,电极Ni(1 nm)/Ag/Ti/Au在400℃氧气中快速退火后得到了较好的结果,其比接触电阻率为5.5×10-3Ω·cm2,在450 nm处反射率为85%.利用此电极制作了垂直结构发光二极管(LED)器件,LED在350 mA注入电流下,工作电压为3.2 V,发光功率为270 mW,电光转换效率达到24%.     

低接触电阻率Ni/Ag/Ti/Au反射镜电极的研究

研究了Ag的厚度、退火时间、沉积温度对于Ni/Ag/Ti/Au电极的反射率及与p-GaN欧姆接触性能的影响. 利用分光光度计测量反射率, 采用圆形传输线模型计算比接触电阻率. 结果表明: 随着Ag厚度的增加, Ni/Ag/Ti/Au电极的反射率逐渐增大; 在氧气氛围中, 随着退火时间从1 min增至10 min, 300 ℃退火时, 比接触电阻率持续下降, 而对于400-600 ℃退火, 比接触电阻率先减小后增大; 在300和400 ℃氧气中进行1-10 min 的退火后, Ni/Ag/Ti/Au的反射率变化较小, 退火温度高于400 ℃时, 随着退火时间的增加, 反射率急剧下降; 在400 ℃氧气中3 min退火后, 比接触电阻率可以达到3.6×10^-3 Ω·cm². 此外, 适当提高沉积温度可以增加Ni/Ag/Ti/Au的反射率并降低比接触电阻率, 沉积温度为120 ℃条件下的Ni/Ag/Ti/Au电极在450 nm处反射率达到90.1%, 比接触电阻率为6.4×10^-3 Ω·cm². 综合考虑电学和光学性能, 在沉积温度为120 ℃下蒸镀Ni/Ag/Ti/Au (1/200/100/100 nm)并在400 ℃氧气中进行3 min退火可以得到较优化的电极. 利用此电极制作的垂直结构发光二极管在350 mA电流下的工作电压为2.95 V, 输出光功率为387.1 mW, 电光转换效率达到37.5%.     

GaN HEMT欧姆接触模式对电学特性的影响

本文制备了AlGaN/GaN HEMT器件中常规结构与带有纵向接触孔结构的两种接触电极,研究了该两种源欧姆接触模式对器件电学特性的影响.在相同条件下进行快速退火,发现在750?C下退火30 s后,常规结构还没有形成欧姆接触,而带有纵向欧姆接触孔的接触电极与外延片已经形成了良好的欧姆接触.同时,比较了Ti/Al/Ti/Au和Ti/Al/Ni/Au电极退火后表面形态,Ti/Al/Ni/Au具有更好的表面形貌.通过测试两种结构的HEMT器件后,发现采用纵向欧姆接触孔结构器件具有更高的跨导和饱和电流,但是也会在栅极电压为0.5—2 V之间产生严重的电流崩塌现象.     

氧气氛中p-GaN/Ni/Au电极在相同温度不同合金时间下的欧姆接触形成机制和扩散行为

用卢瑟福背散射/沟道技术研究了p-GaN上的Ni/Au电极在氧气氛下相同合金温度(500℃)不同合金时间后的微结构演化,以揭示欧姆接触的形成机制.利用背散射随机谱和RUMP模拟程序研究了电极金属之间的互扩散,用沟道谱探测了电极金属中的氧分布.结合不同合金时间下比接触电阻ρ_c的变化,发现随着合金时间的延长比接触电阻持续降低,在合金时间60 s后降低的速度减慢, Au扩散到GaN的表面,在p-GaN上形成外延结构,O向电极内部扩散反应生成NiO对降低ρ_{关键词： GaN 卢瑟福背散射/沟道 欧姆接触}     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

热退火处理对AuGeNi/n-AlGaInP欧姆接触性能的影响

本文在n-(Al0.27Ga0.73)0.5In0.5P表面通过电子束蒸发Ni/Au/Ge/Ni/Au叠层金属并优化退火工艺成功制备了具有较低接触电阻的欧姆接触,其比接触电阻率在445℃退火600 s时达到1.4×10–4 W·cm2.二次离子质谱仪测试表明,叠层金属Ni/Au/Ge/Ni/Au与n-AlGaInP界面发生固相反应,Ga,In原子由于热分解发生外扩散并在晶格中留下Ⅲ族空位.本文把欧姆接触形成的原因归结为Ge原子内扩散占据Ga空位和In空位作为施主提高N型掺杂浓度.优化退火工艺对低掺杂浓度n-(Al0.27Ga0.73)0.5In0.5P的欧姆接触性能有显著改善效果,但随着n-(Al0.27Ga0.73)0.5In0.5P掺杂浓度提高,比接触电阻率与退火工艺没有明显关系.本文为n面出光的AlGaInP薄膜发光二极管芯片的n电极制备提供了一种新的方法,有望大幅简化制备工艺,降低制造成本.     

传输线模型测量Au/Ti/p型金刚石薄膜的欧姆接触电阻率

采用传输线模型测量了重B掺杂p型金刚石薄膜(约10²⁰cm^-3)上Ti/A u欧姆接触电阻率ρ_c,测试了500℃退火前后及大电流情况下的I-V特性,研究 了退火对ρ_c的影响.结果表明,重掺杂和退火工艺是改善欧姆接触的有效手段. ρ_c随测试温度的变化表明金属/半导体接触界面载流子输运机制为隧道穿透.而 光照对ρ_c影响的分析表明金刚石可作为理想窗口材料.测试得到的最低ρ _c值约为10^-4Ωcm². 关键词： 金刚石薄膜 欧姆接触 接触电阻率     

RF-sputtered CrB2 diffusion barrier for Ni/Au Ohmic contacts on p-CuCrO2

Ohmic contacts to p-type CuCrO₂ using Ni/Au/CrB₂/Ti/Au contact metallurgy are reported. The samples were annealed in the 200–700 °C range for 60 s in flowing oxygen ambient. A minimum specific contact resistance of 2 × 10⁻⁵ Ω cm² was obtained after annealing at 400 °C. Further increase in the annealing temperature (>400 °C) resulted in the degradation of contact resistance. Auger Electron Spectroscopy (AES) depth profiling showed that out-diffusion of Ti to the surface of the contact stacks was evident by 400 °C, followed by Cr at higher temperature. The CrB₂ diffusion barrier decreases the specific contact resistance by almost two orders of magnitude relative to Ni/Au alone.     

Rapid thermal annealing induced changes on the contact of Ni/Au to N-doped ZnO

N-doped p-type ZnO (p ∼ 10¹⁸cm^-3) was grown on sapphire(0 0 0 1) substrate by metal-organic chemical vapor deposition method. Ni/Au metal was evaporated on the ZnO film to form contacts. As-deposited contacts were rectifying while ohmic behavior was achieved after thermally annealing the contacts in nitrogen environment. Specific contact resistance was determined by circular transmission line method and a minimum specific contact resistance of 8 × 10⁻⁴ Ω cm² was obtained for the sample annealed at 650 °C for 30 s. However, Hall effect measurements indicate that, as the rapid thermal annealing temperature increased up to 550 °C or higher the samples’ conductive type have changed from p-type to n-type, which may be due to the instability nature of the present-day p-type N-doped ZnO or the dissociation of ZnO caused by annealing process in N₂ ambient. Evolution of the sample's electric characteristics and the increment of metal/semiconductor interface states induced by rapid thermal annealing process are supposed to be responsible for the improvement of electrical properties of Au/Ni/ZnO.     

不同退火方式对Ni/SiC接触界面性质的影响

采用快速热退火(rapid thermal annealing, RTA)法和脉冲激光辐照退火(laser spark annealing, LSA)法, 在n型4H-SiC的Si面制备出Ni电极欧姆接触. 经传输线法测得RTA样品与LSA样品的比接触电阻分别为5.2×10^-4 Ω·cm², 1.8× 10^-4 Ω·cm². 使用扫描电子显微镜、原子力显微镜、透射电子显微镜、拉曼光谱等表征手段, 比较了两种退火方式对电极表面形貌、电极/衬底截面形貌和元素成分分布、SiC衬底近表层碳团簇微结构的影响. 结果表明, 相比于RTA, LSA法制备出的欧姆接触在电极表面形貌、界面形貌、电极层组分均匀性等方面都具有明显优势, 有望使LSA成为一种非常有潜力的制备欧姆接触的退火处理方法.     

GaN基紫光LED的高反射率p型欧姆接触

研究用于GaN基大功率倒装焊(Flip-chip)紫光LED(UV-LED)的高反射率p型欧姆接触的电学和光学性能。用磁控溅射的方法在GaN基LED外延片表面沉积了不同厚度Ag,Al,Au和Pd四种金属,测量了样品的反射率和透射率。结合同步辐射高强度X射线衍射和AFM对金属薄膜的晶体结构进行分析,并对表面形貌进行了观测,对由金属薄膜构成的多层膜结构及其对光反射率的作用机理进行了研究。测量结果表明,在入射光波长为400nm时,Ni/Au/Ag和Ni/Au/Al电极的反射率比Ni/Au的反射率提高了三倍。同时与p-GaN有良好的欧姆接触特性。     

Self-aligned-gate AlGaN/GaN heterostructure field-effect transistor with titanium nitride gate

Self-aligned-gate heterostructure field-effect transistor(HFET) is fabricated using a wet-etching method.Titanium nitride(TiN) is one kind of thermal stable material which can be used as the gate electrode.A Ti/Au cap layer is fixed on the gate and acts as an etching mask.Then the T-shaped gate is automatically formed through over-etching the TiN layer in 30% H_2O_2 solution at 95 ℃.After treating the ohmic region with an inductively coupled plasma(ICP) method,an Al layer is sputtered as an ohmic electrode.The ohmic contact resistance is approximately 0.3 Ω·mm after annealing at a low-temperature of 575 ℃ in N_2 ambient for 1 min.The TiN gate leakage current is only 10~(-8) A after the low-temperature ohmic process.The access region length of the self-aligned-gate(SAG) HFET was reduced from 2 μm to 0.3 μm compared with that of the gate-first HFET.The output current density and transconductance of the device which has the same gate length and width are also increased.     

氧气后处理对氧化锌薄膜紫外发射性质的影响

为了提高ZnO光发射效率和制备p型ZnO,对热处理的氧分压对薄膜的结构、形貌、光致光发射和ZnO/Si异质结的Ⅰ-Ⅴ特性的影响进行了研究.用直流反应溅射法在p型硅衬底上生长ZnO薄膜形成n-ZnO/P-Si异质结.在1000℃下用不同比例的氧和氨热处理,我们发现,在纯氮气中得到的样品有强的紫外发射(390nm),随氧气比例增大,紫外增强,同时绿光也产生并随之增强.但过大的氧分压反而产生多的受主缺陷,使越来越多的激发能量转移到发射能量低的绿光中心,从而使紫外减弱.在纯氧和无氧条件下热处理的俄歇谱表明纯氧下氧过量,而无氧下锌大大过量.ZnO/p-Si异质结的Ⅰ-Ⅴ特性表明,无氧热处理表现为典型的n-ZnO/p-Si异质结;而在纯氧气氛中处理后所得Ⅰ-Ⅴ曲线反向,这表明在高氧压下受主缺陷的产生,表明ZnO薄膜有可能由于高氧压热处理由n型转为p型.     

高反射率p-GaN欧姆接触电极

根据光学薄膜原理计算了GaN/Ti/Ag、GaN/Al和GaN/Ni/Au/Ti/Ag、GaN/Ni/Au/Al多层电极结构的反射率,得出Ag基和Al基反射电极均能在全角范围内提供较高的反射率。实验测量结果表明,反射率能高于80%的Ag基反射电极,具有低欧姆接触的电学特性。并将GaN/Ni/Au/Ti/Ag多层反射电极应用在上下电极结构的GaN基LED中。实验上采用两步合金法获得了低接触电阻、高反射率的电极结构,并引入Ni/Au覆盖层克服了Ag高温时的团聚和氧化现象。解决了Ag电极的稳定性问题,显著地提高了LED的出光效率,成功制备了具有上下电极结构的GaN基LED管芯。     

Study of Ti/Au,Ti/Al/Au,and Ti/Al/Ni/Au ohmic contacts to <Emphasis Type="Italic">n</Emphasis>-GaN

The contacts of Ti/Au, Ti/Al/Au, and Ti/Al/Ni/Au films deposited on n-GaN were studied by current–voltage (I–V) and transmission-line-method measurements. The effect of annealing temperature on specific contact resistivity has been investigated by changing the annealing temperature from 400 to 900 °C. Ti/Al/Au and Ti/Al/Ni/Au films were superior to the bilayer (Ti/Au) in ohmic contact characteristics and thermal stability. The Ti/Al/Ni/Au composite showed the best thermal stability due to the fact that Ni plays a more important role than the alloy of Ti/Al in preventing the interdiffusion of Ti, Al, and Au. The lowest contact resistivity (10^-7cm²) to n-GaN was obtained for the Ti/Al/Ni/Au sample by short-time/high-temperature annealing. The formation mechanism of ohmic contacts to n-GaN is also discussed. PACS 73.40.Cg; 73.61.Ey     

Low specific contact resistivity to graphene achieved by AuGe/Ni/Au and annealing process

Low metal-graphene contact resistance is important in making high-performance graphene devices.In this work,we demonstrate a lower specific contact resistivity of Au_(0.88)Ge_(0.12)/Ni/Au-graphene contact compared with Ti/Au and Ti/Pt/Au contacts.The rapid thermal annealing process was optimized to improve AuGe/Ni/Au contact resistance.Results reveal that both pre- and post-annealing processes are effective for reducing the contact resistance.The specific contact resistivity decreases from 2.5 × 10~(-4) to 7.8 × 10~(-5) Ω·cm~2 by pre-annealing at 300 ℃ for one hour,and continues to decrease to9.5 × 10~(-7) H·cm~2 after post-annealing at 490 ℃ for 60 seconds.These approaches provide reliable means of lowering contact resistance.     

Electrical, structural and surface morphological properties of thermally stable low-resistance W/Ti/Au multilayer ohmic contacts to n-type GaN

A W/Ti/Au multilayer scheme has been fabricated for achieving thermally stable low-resistance ohmic contact to n-type GaN (4.0 × 10¹⁸ cm⁻³). It is shown that the as-deposited W/Ti/Au contact exhibits near linear I-V behaviour. However, annealing at temperature below 800 °C the contacts exhibit non-linear behaviour. After annealing at a temperature in excess of 850 °C, the W/Ti/Au contact showed ohmic behaviour. The W/Ti/Au contact produced specific contact resistance as low as 6.7 × 10⁻⁶ Ω cm² after annealing at 900 °C for 1 min in a N₂ ambient. It is noted that the specific contact resistance decreases with increase in annealing temperature. It is also noted that annealing the contacts at 900 °C for 30 min causes insignificant degradation of the electrical and thermal properties. It is further shown that the overall surface morphology of the W/Ti/Au stayed fairly smooth even after annealing at 900 °C. The W/Ti/Au ohmic contact showed good edge sharpness after annealing at 900 °C for 30 min. Based on the Auger electron spectroscopy and glancing angle X-ray diffraction results, possible explanation for the annealing dependence of the specific contact resistance of the W/Ti/Au contacts are described and discussed.