用金刚石车削技术制备EOS实验用铝薄膜和铜薄膜

 具有材料理论密度的金属薄膜对于材料高压状态方程(EOS)研究而言具有重要的意义。本文提出采用金刚石车削技术,利用超精密金刚石车床、金刚石圆弧刀具及真空吸附夹持技术,对纯铝和无氧铜进行端面车削,完成了EOS实验用铝薄膜和铜薄膜的车削加工,实现了薄膜密度接近材料理论密度。精加工工艺参数为：进给量0.001 mm/r,主轴转速3000 r/min,切削深度1 μm。采用Form Talysurf series 2型触针式轮廓仪进行测量,结果表明：铝薄膜、铜薄膜厚度可以达到小于10 μm水平,表面均方根粗糙度小于5 nm,原始最大轮廓峰-谷高度小于50 nm,厚度一致性好于99%。     

Application of printed nanocrystalline diamond film for electron emission cathode

The low-cost and large area screen-printed nano-diamond film (NDF) for electronic emission was fabricated. The edges and corners of nanocrystalline diamond are natural field-emitters. The nano-diamond paste for screen-printing was fabricated of mixing nano-graphite and other inorganic or organic vehicles. Through enough disperse in isopropyl alcohol by ultrasonic nano-diamond paste was screen-printed on the substrates to form NDF. SEM images showed that the surface morphology of NDF was improved, and the nano-diamond emitters were exposed from NDF through the special thermal-sintering technique and post-treatment process. The field emission characteristics of NDF were measured under all conditions with 10⁻⁶ Pa pressure. The results indicated that the field emission stability and emission uniformity of NDF were improved through hydrogen plasma post-treatment process. The turn-on field decreased from 1.60 V/μm to 1.25 V/μm. The screen-printed NDF can be applied to the displays electronic emission cathode for low-cost outdoor in large area.     

Ordered conducting polymer multilayer films and its application for hole injection layers in organic light-emitting devices

We reported a controlled architecture growth of layer-ordered multilayer film of poly(3,4-ethylene dioxythiophene) (PEDOT) via a modified Langmuir-Blodgett (LB) method. An in situ polymerization of 3,4-ethylene dioxythiophene (EDOT) monomer in multilayer LB film occurred for the formation of ordered conducting polymer embedded multilayer film. The well-distribution of conducting polymer particles was characterized by secondary-ion mass spectrometry (SIMS). The conducting film consisting of ordered PEDOT ultrathin layers was investigated as a hole injection layer for organic light-emitting diodes (OLEDs). The results showed that, compared to conventional spin-coating PEDOT film and electrostatic self-assembly (ESA) film, the improved performance of OLEDs was obtained after using ordered PEDOT LB film as hole injection layer. It also indicated that well-ordered structure of hole injection layer was attributed to the improvement of OLED performance, leading to the increase of charged carrier mobility in hole injection layer and the recombination rate of electrons and holes in the electroluminescent layer.     

Combustion synthesis and luminescent properties of a new material Li2(Ba0.99,Eu0.01)SiO4:B for ultraviolet light emitting diodes

Using urea as fuel and boric as flux, a novel bluish green emitting phosphor Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ has been successfully synthesized using a combustion method. The material has potential application as the fluorescent material for ultraviolet light-emitting diodes (UV-LEDs). The dependence of the properties of Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ phosphors upon urea concentration, boric acid doping and initiating combustion temperature were investigated. The crystallization and particle sizes of Li₂(Ba_0.99,Eu_0.01)SiO₄:B³⁺ have been investigated by using powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). Luminescence measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a bluish green light with peak wavelength of 490 nm. The results showed that the boric acid was effective in improving the luminescence intensity of Li₂(Ba_0.99,Eu_0.01)SiO₄ and the optimum molar ratio of boric acid to barium nitrate was about 0.06. The optimized phosphors Li₂(Ba_0.99,Eu_0.01)SiO₄:B_0.06³⁺ showed 160% improved emission intensity compared with that of the Li₂(Ba_0.99,Eu_0.01)SiO₄ phosphors under UV (λ_ex=350 nm) excitation.     

The insert of zinc oxide thin film in indium tin oxide anode for organic electroluminescence devices

Zinc oxide films were prepared by rf magnetron sputtering on glass substrates with designed ZnO target using high-purity of zinc oxide (99.99%) powder. Systematic study on dependence of target-to-substrate distance (D_ts) on structural, electrical and optical properties of the as-grown ZnO films was mainly investigated in this work. XRD showed that highly preferred ZnO crystal in the [0 0 1] direction was grown in parallel to the substrate, while the D_ts did not effect to the peak position of XRD. With decreasing D_ts, the growth rate is increased while the electrical resistivity as well as crystal size in the ZnO films was decreased. The XPS data showed that the O/Zn ratio in ZnO films was increased with increasing D_ts in the films. The as-grown ZnO films have an average transmittance of above 85% at the visible region. The optical band gap of the as-grown ZnO films was changed from 3.18 to 3.36 eV with D_ts. With decreasing D_ts, the electrical resistivity was decreased, while the growth rate was increased.A bilayer is used as an anode electrode for organic electroluminescent devices. The bilayer consists of an ultrathin ZnO layer adjacent to a hole-transporting layer and an Indium tin oxide (ITO) outerlayer. We tried to bring low the barrier between the devices as deposited ZnO films on ITO substrates. We fabricated the organic EL structure consisted of Al as a cathode, Al₂O₃ as an electro transport layer, Alq₃ as a luminously layer, TPD as a hole transport layer and ZnO (1 nm)/ITO (150 nm) as an anode. The result of this experiment was not good compared with the case of using ITO, nevertheless, at this structure we obtained the lowest turn-on voltage as the value of 19 V and the good brightness (6200 cd/m²) of the emission light from the devices. Then the quantum efficiency was to be 1.0%.     

Electrochemical, morphological and microstructural characterization of carbon film resistor electrodes for application in electrochemical sensors

The electrochemical and microstructural properties of carbon film electrodes made from carbon film electrical resistors of 1.5, 15, 140 Ω and 2.0 kΩ nominal resistance have been investigated before and after electrochemical pre-treatment at +0.9 V vs SCE, in order to assess the potential use of these carbon film electrodes as electrochemical sensors and as substrates for sensors and biosensors. The results obtained are compared with those at electrodes made from previously investigated 2 Ω carbon film resistors. Cyclic voltammetry was performed in acetate buffer and phosphate buffer saline electrolytes and the kinetic parameters of the model redox system Fe(CN)₆^3−/4− obtained. The 1.5 Ω resistor electrodes show the best properties for sensor development with wide potential windows, similar electrochemical behaviour to those of 2 Ω and close-to-reversible kinetic parameters after electrochemical pre-treatment. The 15 and 140 Ω resistor electrodes show wide potential windows although with slower kinetics, whereas the 2.0 kΩ resistor electrodes show poor cyclic voltammetric profiles even after pre-treatment. Electrochemical impedance spectroscopy related these findings to the interfacial properties of the electrodes. Microstructural and morphological studies were carried out using contact mode Atomic Force Microscopy (AFM), Confocal Raman spectroscopy and X-ray diffraction. AFM showed more homogeneity of the films with lower nominal resistances, related to better electrochemical characteristics. X-ray diffraction and Confocal Raman spectroscopy indicate the existence of a graphitic structure in the carbon films.     

3ω法加热/测温膜中温度波解析及其在微/纳米薄膜导热系数测量中的应用

给出了3ω法测试系统中描述薄膜表面加热/测温膜中温度波动的级数形式解，并将复数温度波动的实部和虚部分开表示.利用该解分析了交流加热频率、加热膜宽度和材料热物性的组合参数对加热膜温度波动幅度的影响.并根据此解对测量原理的数学模型进行了修正，建立了相应的3ω测试系统，首先测定了厚度为500 nm SiO₂薄膜的导热系数，验证了实验系统的合理性.加大了测试频率，利用级数模型在高频段直接得到SiO₂薄膜的导热系数，结合低频段的数据同时确定了Si基体的导热系数.利用级数解分析测试了激光晶体Nd:YAG〈111〉面上多层ZrO₂/SiO₂增透膜的导热系数，测试的ZrO₂薄膜的导热系数比体材料小.进行了不确定度分析.结果表明，提出的分析方法可以有效研究微器件表面薄膜结构的导热性能. 关键词： ω法')" href="#">3ω法 微/纳米薄膜 导热系数 微尺度加热膜     

Green sonochemical synthesis and fabrication of cubic MnFe2O4 electrocatalyst decorated carbon nitride nanohybrid for neurotransmitter detection in serum samples

The binary nanomaterials and graphitic carbon based hybrid has been developed as an important porous nanomaterial for fabricating electrode with applications in non-enzymatic (bio) sensors. We report a fast synthesis of bimetal oxide particles of nano-sized manganese ferrite (MnFe₂O₄) decorated on graphitic carbon nitride (GCN) via a high-intensity ultrasonic irradiation method for C (30 kHz and 70 W/cm²). The nanocomposites were analyzed by powder X-ray diffraction, XPS, EDS, TEM to ascertain the effects of synthesis parameters on structure, and morphology. The MnFe₂O₄/GCN modified electrode demonstrated superior electrocatalytic activity toward the neurotransmitter (5-hydroxytryptamine) detection with a high peak intensity at +0.21 V. The appealing application of the MnFe₂O₄/GCN/GCE as neurotransmitter sensors is presented and a possible sensing mechanism is analyzed. The constructed electrochemical sensor for the detection of 5-hydroxytryptamine (STN) showed a wide working range (0.1–522.6 μM), high sensitivity (19.377 μA μM⁻¹ cm⁻²), and nano-molar detection limit (3.1 nM). Moreover, it is worth noting that the MnFe₂O₄/GCN not only enhanced activity and also promoted the electron transfer rate towards STN detection. The proposed sensor was analyzed for its real-time applications to the detection of STN in rat brain serum, and human blood serum in good satisfactory results was obtained. The results showed promising reproducibility, repeatability, and high stability for neurotransmitter detection in biological samples.