铑(Ⅰ)/三-H_8-联萘单齿亚磷酸酯高效催化双环戊二烯氢甲酰化制备双醛（英文）

双环戊二烯(DCPD)是石脑油和燃料油裂解蒸汽的C5馏分中最重要的组分之一.DCPD经氢甲酰化反应可转化为具有广泛应用前景的三环癸烷不饱和单甲醛(TCDMA)和三环癸烷二甲醛(TCDDA),并可通过还原或胺化进一步转化为相应的醇和胺类化合物,用于农药、医药、润滑油和香料等的合成.但是,由于其分子结构中含有3,4-位和8,9-位两种不同活性的不饱和双键,因此DCPD氢甲酰化反应的产物通常非常复杂.过去数十年,研究者们为此相继开发了高转化率和高选择性的催化体系.但是反应条件相对都比较苛刻,尤其是对于双醛TCDDA的合成,通常需要较高的反应温度和反应压力以及大量的催化剂.本文以2'-联萘位置含有不同酯取代基(OCOMe,OCOPh,OCOAdamantyl和OCOPhCl)的三-H8-联萘单齿亚磷酸酯L1-L4为配体,以不同价态的金属铑前驱体为催化剂,开发了Rh催化DCPD氢甲酰化反应的新体系,并对亚磷酸酯配体、不同价态的金属铑催化剂前驱体、反应温度、反应时间、溶剂以及不同的底物和催化剂的S/C摩尔比对DCPD转化率和TCDDA选择性的影响进行了深入的研究.结果表明,当以金属铑前驱体Rh(acac)(CO)_2和配体L4-OCOPhCl为催化体系时,在DCPD氢甲酰化反应中表现出很高的活性,尤其是当S/C=4000时,TON值达到3286,并且该催化体系对于双醛TCDDA具有良好的选择性.值得注意的是,在相对温和的条件(6 MPa,120℃)下,Rh(Ⅰ)催化剂与氯苯酯基取代的三-H_8-联萘单齿亚磷酸酯所形成的配合物在催化DCPD的氢甲酰化反应中,DCPD的转化率达到99.9%,而双醛TCDDA的选择性达到98.7%.此外,我们采用L4-OCOPhCl作为模型单齿磷酸配体,在溶液中通过NMR对可能形成的Rh(Ⅰ)/亚磷酸酯催化物种进行了深入的考察.~(13)P NMR谱图表明,在DCPD的氢甲酰化反应中,催化物种[Rh(acac)(CO)(L4-OCOPhCl)]比[Rh(acac)(CO)(L2-OCOPh)]具有更好的稳定性,而且只有体积较大的配体L4-OCOPhCl才能与铑前驱体Rh(acac)(CO)_2进行很好的配位.     

Catalytic properties of Fe ion-exchanged mordenite toward the ethanol transformation: influence of the methods of preparation

The transformation of ethanol on Fe ion-exchanged mordenite was compared in the temperature range of 200–400 °C for samples prepared in the solution and solid states. Ethane and methane were found as rather major products, compared to acetaldehyde and acetone. Diethyl ether was also detected as a dehydration product. The conversion was found to increase monotonically (to 96%) with increasing the Fe content (to 100%) and reaction temperature to 400 °C. The selectivity towards acetaldehyde and acetone was found maximum at the temperature 300 °C. Decrease in the catalyst Brönsted acidity due to ion-exchange in solution caused a marked increase in the selectivity toward acetaldehyde at 300 °C. At variance, Fe ion-exchanged in the solid state resulted in a higher Brönsted acidity catalyst of higher selectivity to acetone. The solid state exchanged catalyst formed more coke at 400 °C. The higher zeolite acidity catalyzes the ethane propagation into the coke precursors. The extraordinary formation of ethane as a dominant transformation product (in the absence of H₂ gas supply) is explained mainly to the O-abstracting affinity of the Fe³⁺ ion. Methane may be formed as a result of decomposition reaction at high temperatures. Mössbauer and XRD were applied for characterizing different Fe species involved as active sites in the reaction. Coke deposited on the catalysts was measured by TGA. Other helpful information was obtained from BET of N₂-adsorption and FT–IR of NH₃-adsorption. Fair correlation between the active sites responsible for formation of the various products and the zeolite acidity is discussed along with a possible role for the surface area and pore structure in the reaction activity and selectivity.     

Stability of phospholipid vesicles studied by asymmetrical flow field-flow fractionation and capillary electrophoresis

The stability of zwitterionic phosphatidylcholine vesicles in the presence of 20 mol% phosphatidyl serine (PS), phosphatidic acid (PA), phosphatidyl inositol (PI), and diacylphosphatidyl glycerol (PG) phospholipid vesicles, and cholesterol or calcium chloride was investigated by asymmetrical flow field-flow fractionation (AsFlFFF). Large unilamellar vesicles (LUV, diameter 100 nm) prepared by extrusion at 25 °C were used. Phospholipid vesicles (liposomes) were stored at +4 and −18 °C over an extended period of time. Extruded egg yolk phosphatidylcholine (EPC) particle diameters at peak maximum and mean measured by AsFlFFF were 101 ± 3 nm and 122 ± 5 nm, respectively. No significant change in diameter was observed after storage at +4 °C for about 5 months. When the storage period was extended to about 8 months (250 days) larger destabilized aggregates were formed (172 and 215 nm at peak maximum and mean diameters, respectively). When EPC was stored at −18 °C, large particles with diameters of 700–800 nm were formed as a result of dehydration, aggregation, and fusion processes. In the presence of calcium chloride, EPC alone did not form large aggregates. Addition of 20 mol% of negatively charged phospholipids (PS, PA, PI, or PG) to 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) vesicles increased the electrostatic interactions between calcium ion and the vesicles and large aggregates were formed. In the presence of cholesterol, large aggregates of about 250–350 nm appeared during storage at +4 and −18 °C for more than 1 day.

The effect of liposome storage temperature on phospholipid coatings applied in capillary electrophoresis (CE) was studied by measuring the electroosmotic flow (EOF). EPC coatings with and without cholesterol, PS, or calcium chloride, prepared from liposomes stored at +25, +4, and −18 °C, were studied at 25 °C. The performances of the coatings were further evaluated with three uncharged compounds. Only minor differences were observed between the same phospholipid coatings, showing that phospholipid coatings in CE are relatively insensitive to storage at +25, +4 °C or −18 °C.     

Characterization of surface interaction of inorganic fillers with silane coupling agents

Coupling agent (CA) can not only help filler achieve better dispersion in polymer matrix, but also improve the roughness of the composite with good rigidity at the same time. In this paper, the interaction of silane coupling agents with inorganic fillers (in our case are Mg(OH)₂ and CaCO₃) were studied by pyrolysis gas chromatography (PGC), as well as Fourier transform infrared spectroscopy. By two-step pyrolysis (first at 250 °C, then at 600 °C), physisorbed and chemisorbed silane on fillers can be distinguished. The bonded silane cannot be flash vaporized at 250 °C, it results in new peaks different from that of silane in pyrograms at 600 °C. The chemisorbed amount of silane increases with time and temperature and finally reaches a plateau. The result showed that PGC was an effective analytical tool to prove the existence of interaction between inorganic filler and CA.     

Phosphinoethyl-sulfonatoalkylthioethers and diphenyl-ω-sulfonatoalkyl-phosphines as ligands and polyoxyethylene–polyoxypropylene–polyoxyethylene triblock co-polymers as promoters in the rhodium-catalyzed hydroformylation of 1-dodecene in aqueous two-phase systems

The rhodium-catalyzed hydroformylation of 1-dodecene was investigated with a series of sulfonated water-soluble phosphine ligands at a pressure of 60 bar CO/H₂ and a temperature of 120 °C. Seven different groups of water-soluble phosphines were used for our investigations. We established an optimized ligand/rhodium ratio of 5 for the phosphines 1a, [Ph₂P(CH₂)₂S(CH₂)₂SO₃Na], and 1b, [Ph₂P(CH₂)₂S(CH₂)₃SO₃Na]. The utilized arylphosphino-thioether-alkylsulfonates formed with Rh(I) compounds highly active catalysts which could be recycled. The addition of detergents speeds up the hydroformylation reaction, but disturbs the phase separation (recycling). The best promotion effect and the smallest negative influence on phase separation gave polyoxyethylene–polyoxypropylene–polyoxyethylene triblock co-polymers. The ratio of 1-dodecene/rhodium could be increased up to 10.000 and we achieved turnover numbers (TONs)>50.000 without any surfactant and TONs of about 65.000 in presence of the co-polymers owing to the recycling on the catalytic system.     

Isothermal nucleation and growth kinetics of Pd/Ag alloy phase via in situ time-resolved high-temperature X-ray diffraction (HTXRD) analysis

Among several different approaches to form Pd/Ag alloys for hydrogen separation applications, ex situ studies carried out by conventional X-ray point scanning detectors might fail to reveal the key aspects of the phase transformation between Pd and Ag metals. In this respect, in situ time-resolved high-temperature X-ray diffraction (HTXRD) was employed to study the Pd/Ag alloy phase nucleation and growth kinetics. By the use of linear position sensitive detectors, advanced optics and profile fitting with the use of JADE-6.5 software, isothermal phase evolution of the Pd/Ag alloy at 500 °C, 550 °C and 600 °C under hydrogen atmosphere were quantified to elucidate the mechanistic details of the Pd/Ag alloy phase nucleation and growth pattern. Analysis of the HTXRD data by the Avrami model indicated that the nucleation of the Pd/Ag alloy phase was instantaneous where the growth mechanism was through diffusion-controlled one-dimensional thickening of the Pd/Ag alloy layer. The value of the Avrami exponent, n, was found to increase with temperature with the values of 0.34, 0.39 and 0.67 at 500 °C, 550 °C and 600 °C, respectively. In addition, parabolic rate law analysis suggested that the nucleation of the Pd/Ag alloy phase was through a heterogeneous nucleation mode, in which the nucleation sites were defined as the non-equilibrium defects. Indeed, the cross-sectional SEI micrographs indicated that the Pd/Ag alloy phase growth was strongly dependent upon the deposition morphology of the as-synthesized Pd and Ag layers formed by the electroless plating. Based on the Avrami model and the parabolic rate law, the estimated activation energies for the phase transformation were 236.5 kJ/mol and 185.6 kJ/mol and in excellent agreement with the literature values (183–239.5 kJ/mol). Finally, the in situ annealing of the 15.6 μm thick composite Pd/Ag/PSS membrane at 550 °C in hydrogen atmosphere indicated that the Pd/Ag alloy phase formation was not complete even after 500 h. According to the Avrami model, the increase in the hydrogen permeance from 7.1 m³/m² h atm^0.5 to 21.3 m³/m² h atm^0.5 at 550 °C over a period of 500 h corresponded to an 83% Pd/Ag alloy phase formation.     

An investigation on the solid state pyrolytic decomposition of bimetallic oxalate precursors of Ca, Sr and Ba with cobalt: A mechanistic approach

The mixed metal oxalate precursors, calcium(II)bis(oxalato)cobaltate(II)hydrate (COC), strontium(II)bis(oxalato)cobaltate(II)pentahydrate (SOC) and barium(II)bis(oxalato)cobaltate(II)octahydrate (BOC) have been synthesized and their thermal stability was investigated. The complexes were characterized by elemental analysis, IR spectral and X-ray powder diffraction studies. Thermal decomposition studies (TG, DTG and DTA) in air showed that the compound COC decomposed mainly to CaC₂O₄ and Co₃O₄ at 340 °C, and a mixture of CaCO₃ and Co₃O₄ identified at 510 °C. A mixture of CaCO₃ and Ca₃Co₂O₆ along with the oxides and carbides of both the cobalt and calcium were attributed at 1000 °C as end products. DSC study in nitrogen ascertained the formation of a mixture of CaO and CoO along with a trace of carbon at 550 °C. The mixture species, SrC₂O₄, CoC₂O₄ and Co₃O₄ were generated at 255 °C in case of SOC in air, which ultimately changed to CoSrO₃, SrCO₃ and oxides of strontium and cobalt at 1000 °C. The several mixture species also generated as intermediate at 332 and 532 °C. The DSC study in nitrogen indicated the formation of CoSrO_x (0.5 < x < 1) as end product. In case of BOC in air, a mixture of BaCoO₂, BaO, CoO and carbides are identified as end product at 1000 °C through the generation of several intermediate species at 350 and 530 °C. A mixture of BaO and CoO is identified as end product in DSC study in nitrogen. The kinetic parameters have been evaluated for all the dehydration and decomposition steps of all the three compounds using four non-mechanistic equations. Using seven mechanistic equations, the kind of dominance of kinetic control mechanism of the dehydration and decomposition steps are also inferred. The kinetic parameters, ΔH and ΔS of all the steps are explored from the DSC studies. Some of the decomposition products are identified by IR and X-ray powder diffraction studies.     

Liquid-phase alkylation of phenol with long-chain olefins over WOx/ZrO2 solid acid catalysts

The liquid-phase alkylation of phenol with 1-dodecene was carried out over WO_x/ZrO₂ solid acid catalysts. The catalysts were prepared by wet impregnation method using zirconium oxyhydroxide and ammonium metatungstate. Catalysts with different WO₃ loading (5–30 wt.%) were prepared and calcined at 800 °C and catalyst with 15% WO₃ was calcined from 700–850 °C. All the catalysts were characterized by surface area, XRD, and FTIR. The catalyst with 15% WO₃ calcined at 800 °C (15 WZ-800) was found to be the most active in the reaction. The effect of temperature, molar ratio and catalyst weight on dodecene conversion and products selectivity was studied in detail. Under the optimized reaction conditions of 120 °C, phenol/1-dodecene molar ratio 2 and time 2 h, the catalyst 15 WZ-800 gave >99% dodecene conversion with 90% dodecylphenol selectivity. Comparison of the catalytic activity of 15 WZ-800 with sulfated zirconia calcined at 500 °C (SZ-500) and Hβ zeolite showed that activity of SZ-500 was lower than that of 15 WZ-800, while Hβ zeolite showed negligible activity. It is observed that the presence of water in the reaction mixture was detrimental to the catalytic activity of WO_x/ZrO₂. The catalyst 15 WZ-800 also found to be an efficient catalyst for alkylation of phenol with long-chain olefins like 1-octene and 1-decene.     

Zirconia-supported phosphotungstic acid as catalyst for alkylation of phenol with benzyl alcohol

The liquid-phase alkylation of phenol with benzyl alcohol was carried out using zirconia-supported phosphotungstic acid (PTA) as catalyst. The catalysts with different PTA loadings (5–20 wt.% calcined at 750 °C) and calcination temperature (15 wt.% calcined from 650 to 850 °C) were prepared and characterized by ³¹P MAS NMR and FT-IR pyridine adsorption spectroscopy. The catalyst with optimum PTA loading (15%) and calcination temperature (750 °C) was prepared in different solvents. ³¹P MAS NMR spectra of the catalysts showed two types of phosphorous species, one is the Keggin unit and the other is the decomposition product of PTA and the relative amount of each depends on PTA loading, calcination temperature and the solvent used for the catalyst preparation. The catalysts with 15% PTA on zirconia calcined at 750 °C showed the highest Brönsted acidity. At 130 °C and phenol/benzyl alcohol molar ratio of 2 (time, 1 h), the most active catalyst, 15% PTA calcined at 750 °C gave 98% benzyl alcohol conversion with 83% benzyl phenol selectivity.     

Synthesis, structural investigation and thermal stability of aqua magnesium(II) phthalocyanine bis(diethylamine) solvate

Aqua magnesium phthalocyanine bis(diethylamine) complex was obtained in the crystalline form and its crystal structure was determined by single-crystal X-ray diffraction. The Mg atom is 4 + 1 coordinated by four N isoindole atoms and one O atom. The MgPc moiety is non-planar, the Mg(II) is deviated by 0.492(2) Å from the N₄-isoindole plane towards the oxygen atom of water molecule. The arrangement of MgPc(H₂O) and diethylamine molecules is determined by O–HN hydrogen bonds and π–π interactions. The complex is stable up to 140 °C. At this temperature the complex loses diethylamine molecules and next at 200 °C loses the water molecule and finally converts into β-MgPc.     

Kinetics and mechanisms of homogeneous catalytic reactions: Part 6. Hydroformylation of 1-hexene by use of Rh(acac)(CO)2/dppe [dppe = 1,2-bis(diphenylphosphino)ethane] as the precatalyst

A kinetic study of the homogeneous hydroformylation of 1-hexene to the corresponding aldehydes (heptanal and 2-methyl-hexanal) was carried out using a rhodium catalyst formed by addition of 1 equiv. of 1,2-bis(diphenylphosphino)ethane (dppe) to Rh(acac)(CO)₂ under mild reaction conditions (80 °C, 1–7 atm H₂ and 1–7 atm CO) in toluene; in all cases linear to branched ratios were close to 2. The reaction rate is first-order in dissolved hydrogen concentration at pressures below 3 atm, but independent of this parameter at higher pressures. In both regimes (low and high H₂ pressure), the initial rate was first-order with respect to the concentration of Rh and fractional order with respect to 1-hexene concentration. Increasing CO pressure had a positive effect on the rate up to a threshold value above which inhibition of the reaction was observed; the range of positive order on CO concentration is smaller when the total pressure is increased. The kinetic data and related coordination chemistry are consistent with a mechanism involving RhH(CO)(dppe) as the active species initiating the cycle, hydrogenolysis of the acyl intermediate as the rate-determining step of the catalytic cycle at low hydrogen pressure, and migratory insertion of the olefin into the metal-hydride bond as rate limiting at high hydrogen pressure. This catalytic cycle is similar to the one commonly accepted for RhH(CO)(PPh₃)₃ but different from previous proposals for Rh-diphosphine catalysts.     

Chemistry and reactivity of dinuclear manganese oxamate complexes: Aerobic catechol oxidation catalyzed by high-valent bis(oxo)-bridged dimanganese(IV) complexes with a homologous series of binucleating 4,5-disubstituted-o-phenylenedioxamate ligands

The high-valent bis(oxo)-bridged dimanganese(IV) complexes with the series of binucleating 4,5-X₂-o-phenylenebis(oxamate) ligands (opbaX₂; X = H, Cl, Me) (1a–c) have been synthesized and characterized structurally, spectroscopically and magnetically. Complexes 1a–c possess unique Mn₂(μ-O)₂ core structures with two o-phenylenediamidate type additional bridges which lead to exceptionally short Mn–Mn distances (2.63–2.65 Å) and fairly bent Mn–O–Mn angles (94.1°–94.6°). The cyclovoltammograms of 1a–c in acetonitrile (25 °C, 0.1 M Bu₄NPF₆) show an irreversible one-electron oxidation peak at moderately high anodic potentials (E_ap = 0.50–0.85 V versus SCE), while no reductions are observed in the potential range studied (down to −2.0 V versus SCE). These dinuclear manganese oxamate complexes are excellent catalysts for the aerobic oxidation of 3,5-di-tert-butylcatechol to the corresponding o-quinone in acetonitrile at 25 °C. The order of increasing catecholase activity (k_obs) with the electron donor character of the ligand substituents as 1b (X = Cl) < 1a (X = H) < 1c (X = Me) correlates with Hammett σ⁺ values (ρ = −0.95). A mechanism involving initial activation of the catechol substrate by coordination to the dimetal center and subsequent oxidation to quinone by O₂ is proposed, which is consistent with the observed saturation kinetics.     

Laser induced breakdown spectroscopy of soils, rocks and ice at subzero temperatures in simulated martian conditions

We applied Laser Induced Breakdown Spectroscopy (LIBS) on moist soil/rock samples in simulated Martian conditions. The signal behavior as a function of the surface temperature in the range from + 25 °C to − 60 °C was studied at pressure of 7 mbar. We observed the strong signal oscillations below 0 °C with different negative peaks, whose position, width and magnitude depend on the surface roughness. In some cases, the signal was reduced for one order of magnitude with consequences for the LIBS analytical capability. We attribute such a signal behavior to the presence of supercooled water inside the surface pores, which freezing point depends on the pore size. On a same rock samples with different grades of the surface polishing, the signal has different temperature dependence. Its decrease was always registered close to 0 °C, corresponding to the freezing/melting of normal disordered ice, which can be present inside larger pores and scratching. An amount of the signal reduction at the phase transition temperatures does not seem to change with the laser energy density in the examined range. Comparative measurements were performed on a frozen water solution. A large depression, for two orders of magnitude, of the LIBS intensity was observed close to − 50 °C. The same negative peak, but with a smaller magnitude, was also registered on some rock/soil samples. Ablation rates and plasma parameters as a function of the sample temperature are also discussed, and their consequences for in-situ analyses.     

Measurement of glass transition temperature by mechanical (DMTA), thermal (DSC and MDSC), water diffusion and density methods: A comparison study

Glass transition measured by DMTA from the change in slope in storage modulus was 55 °C, which was 10.5 °C lower than the value measured by tan δ peak. Initial glass transition measured by DSC, increased exponentially and reached a constant value of 55 °C at or higher heating rate of 30 °C/min. Transition temperature, measured by MDSC, remained constant up to heating rate 15 °C/min and then decreased. The glass transition values determined from reversible heat flow was 60 °C. The break in diffusivity and density (i.e. volume) was observed at 50 °C below the glass transition temperature measured by thermal and mechanical methods.     

Binary modifiers for the determination of zinc in pure copper and nickel-based alloy by longitudinal Zeeman electrothermal atomic absorption spectrometry

The determination of zinc in pure copper and nickel-based alloy was successfully accomplished with a longitudinal Zeeman-effect correction and end-capped transversely heated graphite atomizer. Since aqua regia (an acid mixture of nitric acid and hydrochloric acid, 1:3, v/v) was used as the dissolving reagent, volatile ZnCl₂ was formed. Consequently, less Zn was found in the sample. EDTA could improve the atomic absorption profiles. Binary modifiers, EDTA + Pd(NO₃)₂ and EDTA + Mg(NO₃)₂, were effective for eliminating the chloride interference and the spectral interference from Cu I 213.853 nm. The experimental results obtained with and without the modifiers were compared. Increase of 200 °C in the pyrolysis temperature resulted from the addition of binary modifiers for both pure copper and nickel-based alloys. For pure copper, the atomization temperature increased from 1400 to 1600 °C whereas the atomization temperature increased from 1100 to 1600 °C for nickel-based alloys. The analytical performance of the proposed method was evaluated. Zinc contents in the pure copper and nickel-based alloy standards determined with both binary modifiers agreed closely with the certified values. The recovery ranged from 93 ± 2 to 104 ± 6% at 95% confidence level. The detection limits obtained by the binary modifiers of EDTA + Pd(NO₃)₂ and EDTA + Mg(NO₃)₂ were 0.77 and 0.31 pg, respectively.     

Time-dependent fluctuations in infrared vsCH2 frequencies in acyl chain membranes of Acholeplasma laidlawii cells

We measured FT-IR spectra of intact Acholeplasma laidlawii cells grown at 37 °C on palmitic acid (C16:0) or on binary palmitic acid-d31/oleic acid (C16:0-d31/C18:1(9)) at an initial mole ratio of 2:3, which have been previously reported to produce significant fluctuations in CH₂ symmetric stretching (ν_sCH₂) and CD₂ asymmetric stretching (ν_aCD₂) frequencies (Biochim. Biophys. Acta 1279 (1996) 49). Time courses for acyl chain ν_sCH₂ and ν_aCD₂ frequencies determined from fourth derivative spectra are presented. Fluctuations were detected with the C16:0 enriched cells at temperatures above 40 °C as well as with the cells enriched in 2:3 C16:0-d₃₁/C18:1(9). These observations at temperatures above 40 °C for the C16:0 enriched cells were not in agreement with the conclusion in the previous work by Moore et al. Our results have suggested that the 2850 cm⁻¹ ν_sCH₂ band comprises two components arising from trans and gauche conformations, and that the fluctuations in ν_sCH₂ frequency are caused by random temporal changes in the relative intensities of these two components.     

Effects of heat on physicochemical properties of whey protein-stabilised emulsions

The effect of heating has been studied for whey protein-stabilised oil-in-water emulsions (25.0% (w/w) soybean oil, 3.0% (w/w) whey protein isolate, pH 7.0). These emulsions were heated between 55 and 95 °C as a function of time and the effect on particle size distribution, adsorbed protein amount, protein conformation and rheological properties was determined. Heating the emulsions as a function of temperature for 25 min resulted in an increase of the mean diameter (d₃₂) and shear viscosity with a maximum at 75 °C. Heating of the emulsions at different temperatures as a function of time in all cases resulted in a curve with a maximum for d₃₂. A maximum increase of d₃₂ was observed after about 45 min at 75 °C and after 6–8 min at 90 °C. Similar trends were observed with viscosity measurements. Confocal scanning laser micrographs showed that after 8 min of heating at 90 °C large, loose aggregates of oil droplets were formed, while after 20 min of heating compact aggregates of two or three emulsion droplets remained. An increase of the adsorbed amount of protein was found with increasing heating temperature. Plateau values were reached after 10 min of heating at 75 °C and after 5 min of heating at 90 °C. Based on these results we concluded that in the whole process of aggregation of whey protein-stabilised emulsions an essential role is played by the non-adsorbed protein fraction, that the kinetics of the aggregation of whey protein-stabilised emulsions follow similar trends as those for heated whey protein solutions and that upon prolonged heating rearrangements take place leading to deaggregation of initially formed large, loose aggregates of emulsion droplets into smaller, more compact ones.     

The effect of humidity on dehydration behavior of nitrofurantoin monohydrate studied by humidity controlled simultaneous instrument for X-ray Diffractometry and Differential Scanning Calorimetry (XRD–DSC)

The dependence of thermal dehydration behavior of nitrofurantoin monohydrate on humidity was studied. Difference in observed crystallinity of resulting anhydrates under three humidity conditions is discussed in relation to the effect of water vapor molecules. Thermal dehydration of nitrofurantoin monohydrate was measured using a humidity controlled simultaneous measurement instrument for X-ray Diffractometry (XRD) and Differential Scanning Calorimetry (DSC) in dry, 27 °C 91% RH and 60 °C 90% RH nitrogen. Dehydration of nitrofurantoin in dry nitrogen gave a mixture of crystalline and amorphous anhydrates in the temperature range of 124–180 °C followed by crystallization around 185–190 °C. Whereas, dehydration in high humidity atmosphere (60 °C 90% RH or 17.7% H₂O–82.3% N₂) gave well crystallized anhydrate at 140 °C soon after dehydration. Dehydration in low humidity nitrogen (27 °C 91% RH or 3.2% H₂O–96.8% N₂) gave not totally crystalline anhydrate, which became pure crystalline at around 190 °C. The effect of high humidity on dehydration and crystallinity of the resulting anhydrate can be attributed to the role of water vapor molecules in two ways such as the acceleration of molecular mobility and high molecular diffusion rate of nitrofurantoin anhydrate, and the formation of hydrogen bonding bridges quickly connecting dehydrated molecules to one another.     

Thermoluminescence characteristics of minerals from irradiated potatoes of different origins of production

Thermoluminescence (TL) characteristics were investigated for minerals, which were separated from potatoes irradiated at 0–1 kGy of different origins of production in Korea. The polyminerals analyzed by X-ray diffractometer were mainly composed of quartz and feldspar, and showed varied contents with producing origins, that contributed to typical TL responses to irradiation. The glow curve of irradiated samples at 0.05–1 kGy peaked at approximately 200°C with high intensity, but that of non-irradiated potatoes was observed at approximately 300°C with low intensity. Discrimination between irradiated (more than 0.05 kGy) and non-irradiated samples was possible just on the basis of the first glow curve, however, normalization of results through a re-irradiation step greatly improved their reliability. The signal intensity of TL decreased with the lapse of post-irradiation time under different storage conditions (0±0.5°C/dark room, 25±5°C/dark room and 25±5°C/naturally lighted room) but was still distinguishable from that of the non-irradiated sample even after one year.