Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.     

Effect of magnetic nanoparticles on the thermal properties of some hydrogels

Magnetic hydrogels (ferrogels) based on poly(vinyl alcohol) (PVA) and poly(hydroxyethyl methacrylate) (PHEMA) with magnetite (Fe₃O₄) nanoparticles were prepared. PVA ferrogels were synthesised by submitting the aqueous solution of polymer and Fe₃O₄ to freezing-thawing (F-T) cycles yielding a physical gel. Different samples were prepared by varying (i) the concentration of PVA, (ii) the concentration of magnetite and (iii) the number of F-T cycles applied. PHEMA ferrogels were prepared by a crosslinking polymerization reaction in the presence of magnetite yielding chemical gels. Different samples were prepared by varying (i) the concentration of HEMA, (ii) the concentration of EGDMA and (iii) the concentration of magnetite nanoparticles. All ferrogel samples were first dried before been analysed in a thermogravimetric analyzer. The resulting thermograms showed that the concentration of magnetite nanoparticles does affect the thermal stability of either ferrogels system, a general improvement in comparison with PVA and PHEMA hydrogels, respectively, being observed. The apparent activation energy (E_a) of the thermal degradation for PVA ferrogels was evaluated and calculated applying the Flynn-Wall and the Kissinger methods. Values of apparent E_a increased with the content of Fe₃O₄ in the ferrogel sample.     

Determination of the Thermal Degradation Kinetic Parameters of Carbon Fibre Reinforced Epoxy Using TG

In this work, a kinetic study on the thermal degradation of carbon fibre reinforced epoxy is presented. The degradation is investigated by means of dynamic thermogravimetric analysis (TG) in air and inert atmosphere at heating rates from 0.5 to 20°C min⁻¹ . Curves obtained by TG in air are quite different from those obtained in nitrogen. A three-step loss is observed during dynamic TG in air while mass loss proceeded as a two step process in nitrogen at fast heating rate. To elucidate this difference, a kinetic analysis is carried on. A kinetic model described by the Kissinger method or by the Ozawa method gives the kinetic parameters of the composite decomposition. Apparent activation energy calculated by Kissinger method in oxidative atmosphere for each step is between 40–50 kJ mol⁻¹ upper than E _a calculated in inert atmosphere. The thermo-oxidative degradation illustrated by Ozawa method shows a stable apparent activation energy (E _a ≈130 kJ mol⁻¹ ) even though the thermal degradation in nitrogen flow presents a maximum E _a for 15% mass loss (E _a ≈60 kJ mol⁻¹ ). This revised version was published online in July 2006 with corrections to the Cover Date.     

TG studies of a composite solid rocket propellant based on HTPB-binder

Thermal decomposition kinetics of solid rocket propellants based on hydroxyl-terminated polybutadiene-HTPB binder was studied by applying the Arrhenius and Flynn-Wall-Ozawa's methods. The thermal decomposition data of the propellant samples were analyzed by thermogravimetric analysis (TG/DTG) at different heating rates in the temperature range of 300-1200 K. TG curves showed that the thermal degradation occurred in three main stages regardless of the plasticizer (DOA) raw material, the partial HTPB/IPDI binder and the total ammonium perchlorate decompositions. The kinetic parameters E _a (activation energy) and A (pre-exponential factor) and the compensation parameter (S _p) were determined. The apparent activation energies obtained from different methods showed a very good agreement. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal behaviour, compatibility study and decomposition kinetics of glimepiride under isothermal and non-isothermal conditions

In the present work, the thermal decomposition of glimepiride (sulfonylurea hypoglycemic agent) was studied using differential scanning calorimetry (DSC) and thermogravimetry/derivative thermogravimetry (TG/DTG). Isothermal and non-isothermal methods were employed to determine kinetic data of decomposition process. The physical chemical properties and compatibilities of several commonly used pharmaceutical excipients (glycolate starch, microcrystalline cellulose, stearate, lactose and Plasdone®) with glimepiride were evaluated using thermoanalytical methods. The 1:1 physical mixtures of these excipients with glimepiride showed physical interaction of the drug with Mg stearate, lactose and Plasdone®. On the other hand, IR results did not evidence any chemical modifications. From isothermal experiments, activation energy (E _a) can be obtained from slope of lnt vs. 1/T at a constant conversion level. The average value of this energy was 123 kJ mol^–1. For non-isothermal method E _a can be obtained from plot of logarithms of heating rates, as a function of inverse of temperature, resulting a value of 157 and 150 kJ mol^–1, respectively, in air and N₂ atmosphere, from the first stage of thermal decomposition.     

Thermogravimetry of the thermal degradation of Japanese lacquer (urushi) films

The kinetics of the thermal degradation of Japanese lacquer (urushi) films in N₂ and in air were studied by means of thermogravimetry (TG). Thermogravimetric and derivative thermogravimetric curves indicated that the degradation occurred in three stages. The atmosphere influenced the apparent activation energies (E _a) of the three degradation stages. The activation energies (E _a) for the first stage in N₂ and air, obtained from the TG curve, were 19.12 and 10.19 kcal mol^?1, respectively, and the corresponding pre-exponential factors (A) were 6.18 × 10⁵ and 1.24 × 10² min^?1 for 1-year-old urushi films.     

Investigations and molecular modeling of some thermophysical properties of polysulfones

Degradation of commercial polysulfones (PSF) was investigated in air and in inert atmosphere (nitrogen) using thermogravimetric (TG) method. It has been found that the degradation of Udel P-1800 PSF is initiated about 400°C, both in air and in nitrogen. The activation energy of degradation of PSF, (E _a), has been calculated by the Kissinger and Ozawa methods. The value ofE _a about 200 kJ·mol^?1 has been found for both air and nitrogen atmosphere. Experimental results concerning thermal properties of PSF (T _g andT _d,1/2) were compared with those obtained by the computer modeling technique, and a good agreement has been found.     

Two novel algorithms for the thermogravimetric assessment of polymer degradation under non-isothermal conditions

Two novel algorithms are presented for processing thermogravimetric (TG) data obtained during the degradation of a polymer in a single step mechanism under non-isothermal conditions. The first algorithm assesses three characteristics computed from the TG profile against a theoretical data set, and identifies likely kinetic models to fit the experimental data. The second algorithm provides an iterative arithmetic method to extract the apparent activation energy, E_a, and Arrhenius A-factor, A, from TG data without simplifying assumptions. The algorithms are validated using model data and applied to data for the non-isothermal degradation of poly(ethylene adipate), poly(lactic acid) (PLA) and a food packaging PLA composite formulation containing kenaf, a natural fibre. The analysis of poly(ethylene adipate) produced E_a = 137 kJ mol⁻¹ and log₁₀A = 8.71 (first-order kinetic model). The kenaf fibre destabilizes PLA, lowering its E_a from 190 kJ mol⁻¹ to 150 kJ mol⁻¹ (contracting volume model).     

The investigation of methyl phenyl silicone resin/epoxy resin using epoxy-polysiloxane as compatibilizer

Styrene–butadiene rubber was subjected to long-term thermal aging treatment at 80 °C with aging period up to 180 days. The degradation kinetics of the aged sample was analyzed by thermogravimetric analysis. Multiple heating rate experiments were carried out in nonisothermal conditions and three isoconversional model-free methods (Friedman; Kissinger–Akahira–Sunose; Li and Tang methods) were employed. The results showed that the temperature for 5 % mass loss increased, whereas the maximum mass loss temperature decreased after aging. Activation energies (E _a) derived from the three methods were found to be dependent on conversion degree (α). E _a increased with increasing α in the whole range of conversion for samples aged for 0, 60, and 120 days, while the aged samples displayed higher E _a values. However, samples aged for 180 days showed declining E _a versus α. The changes on the degradation kinetics were associated with the modification on the chemical structure after thermal aging.     

The regression of isothermal thermogravimetric data to evaluate degradation Ea values of polymers: A comparison with literature methods and an evaluation of lifetime predictions reliability. Part II

The kinetics of the isothermal degradation in static air atmosphere of four well known polymers, polyethylene (PE), polystyrene (PS), polycarbonate (PC) and poly(methyl methacrylate) (PMMA) was studied by both a long-term (more than three years) experiment at relatively low temperature (423 K) and a set of short-term experiments at higher temperatures. The activation energy (E_a) values of degradation were determined by both the MacCallum and Wilkinson literature methods, and were compared with those obtained through a new very simple method we set up, based on the direct regression of TG mass loss data. About two years ago we published the results concerning PE and PS because their mass losses during long-term experiments were sufficiently high. The long-term degradation experiments were continued until now and in this second part we report the results concerning PC and PMMA. The degradation E_a values calculated from short-term experimental data through the three different methods were in good agreement with each other for both PC and PMMA, thus confirming the general applicability of our simple method for the determination of E_a. The experimental data at lower temperature of PC were not in agreement with those at higher temperatures, thus confirming the low reliability of the kinetic parameters (and then of lifetime predictions) at low temperature determined by experiments at higher temperatures. Partially disagreeing results were obtained for PMMA, which were discussed and interpreted.     

End-life Prediction of Commercial PLA Used for Food Packaging through Short Term TGA Experiments： Real Chance or Low Reliability？

A long-term(about nine months) isothermal degradation experiment of two different commercial polylactide(PLA) samples used for food packaging was carried out at a relatively low temperature(423 K). Thermooxidative degradations of the same polymers were carried out in a thermogravimetric(TG) analyser, at higher temperatures(453 K ≤ T ≤ 523 K), under isothermal heating conditions. The obtained set of experimental TG data was used to determine the apparent activation energy(Ea) of degradation through two isothermal kinetic methods. The results from long-term experiment evidenced considerable mass loss for both PLA samples in the investigated period, but the experimental data were not in agreement with those from the short-term degradations at higher temperatures, thus suggesting a different degradation kinetics, and, then a low reliability of the lifetime predictions for polymers in service or degradation forecasts for the end of their life based on experiments at higher temperatures.     

Thermal properties and kinetics of new-generation posterior bulk fill composite cured light-emitting diodes

In this study, the thermal behavior in terms of glass transition (T _g), degradation, and thermal stability of four commercial new-generation posterior bulk fill composites (Surefill SDR, Dentsply; Quixfill, Dentsply; Xtrabase, Voco; and Xtrafill, Voco) activated by light-emitting diodes (LEDs) was analyzed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The activation energies (E _a) for the decomposition of the dental resins were calculated based on the Kissinger and Doyle kinetic models from the peaks of the endothermic curves obtained when the specimens were heated at four different temperatures (5, 10, 15, and 20 °C min^?1) during DSC. The results show that the Xtrabase composite displayed the highest T _g (120 °C at a 5 °C min^?1 heating rate) and E _a (157.64 kJ mol^?1) values associated with thermal degradation from the main chain of the polymer.     

Thermal degradation mechanism of highly filled nano-SiO2 and polybenzoxazine

Effects of high nano-SiO₂ loading (up to 30 mass%) on polybenzoxazine (PBA-a) thermal degradation kinetics have been investigated using nonisothermal thermogravimetric analysis (TG). The DTG curves revealed three stages of thermal decomposition process in the neat PBA-a, while the first peak at low temperature was absent in its nanocomposites. As a consequence, the maximum degradation temperature of the nanocomposites shifted significantly to higher temperature as a function of the nano-SiO₂ contents. Moreover, the degradation rate for every degradation stage was found to decrease with the increasing amount of the nano-SiO₂. From the kinetics analysis, dependence of activation energy (E _a) of the nanocomposites on conversion (α) suggests a complex reaction with the participation of at least two different mechanisms. From Coats–Redfern and integral master plot methods, the average E _a and pre-exponential factor (A) of the nanocomposites showed systematically higher value than that of the PBA-a, likely from the shielding effect of the nanoparticles. The main degradation mechanism of the PBA-a was determined to be a random nucleation type with one nucleus on the individual particle (F1 model), while that of the PBA-a nanocomposite was the best described by diffusion-controlled reaction (D3 model).     

Thermal decomposition kinetics of some transition metal coordination polymers of fumaroyl bis (paramethoxyphenylcarbamide) using DTG/DTA techniques

In the present work, thermal degradation behaviors of the Zn (II), Cd(II), and Hg(II) coordination polymers of fumaroyl bis (paramethoxyphenylcarbamide) (fbpmpc) have been investigated by using thermogravimetric (TG) analysis, differential thermal analysis (DTA) and derivative thermogravimetry (DTG) analysis under non-isothermal conditions in nitrogen atmosphere at multiple heating rates. TG–DTA study noteworthy inferred the presence of lattice water in outer sphere of all the polymers. The decomposition was carried out in three-four well-separated stages where involved the loss of water molecules in the first step followed by organic ligand. Furthermore, the kinetics and thermodynamic stabilities of multi-steps thermal degradation were evaluated. The activation energy (E_a), order of reaction (n), Arrhenius factor (A), enthalpy change (ΔH), entropy change (ΔS) and free energy change (ΔG) of coordination polymers were obtained by using the Coats–Redfern (CR) method. Ultimately, based on initial, half and final decomposition temperature, and kinetics parameters values the orders of thermal stability were estimated.     

Thermal investigation of strontium acetate hemihydrate in nitrogen gas

The thermal decomposition of strontium acetate hemihydrate has been studied by TG-DTA/DSC and TG coupled with Fourier transform infrared spectroscopy (FTIR) under non-isothermal conditions in nitrogen gas from ambient temperature to 600°C. The TG-DTA/DSC experiments indicate the decomposition goes mainly through two steps: the dehydration and the subsequent decomposition of anhydrous strontium acetate into strontium carbonate. TG-FTIR analysis of the evolved products from the non-oxidative thermal degradation indicates mainly the release of water, acetone and carbon dioxide. The model-free isoconversional methods are employed to calculate the E _a of both steps at different conversion α from 0.1 to 0.9 with increment of 0.05. The relative constant apparent E _a values during dehydration (0.5<α<0.9) of strontium acetate hemihydrate and decomposition of anhydrous strontium acetate (0.5<α<0.9) suggest that the simplex reactions involved in the corresponding thermal events. The most probable kinetic models during dehydration and decomposition have been estimated by means of the master plots method.     

Thermal behaviors of N-pyrrolidine-N′-(2-chlorobenzoyl)thiourea and its Ni(II), Cu(II), and Co(III) complexes

The N-pyrrolidine-N??-(2-chlorobenzoyl)thiourea, HL, and their Ni(II), Cu(II), and Co(III) complexes (NiL₂, CuL₂, and CoL₃) have been synthesized and characterized. The thermal decomposition reactions of all the compounds have been investigated by DTA/TG combined systems. The mass spectroscopy technique has been used to identify the products during pyrolytic decomposition. The pyrolytic final products have been analyzed by X-ray powder diffraction method. After comparison of thermogravimetric and mass results of HL, NiL₂, CuL₂, and CoL₃, the decomposition mechanism of these compounds have been suggested. The thermal stability of the Ni(II) and Cu(II) complexes according to the thermogravimetric curves follows the sequence: NiL₂?<?CuL₂. The values of the activation energy, E _a, have been obtained using model-free (Kissenger?CAkahira?CSunose, KAS, Flyn?CWall?COzawa, FWO, and Isoconversional) methods for all decomposition stages. The E _a versus the extent of conversion, ??, plots show that the values of E _a varies as ??. Thirteen kinetic model equations have been tested for selecting correct reaction models. The optimized value of E _a and Arrhenius factor, A, have been obtained using the best model equation. The thermodynamic functions (??H*, ??S*, and ??G*) have been calculated using these values.     

Thermal decomposition reactions of metal carboxylato complexes in the solid state. I.: Thermographic and differential thermal studies of metal oxalato,malonato and succinato complexes

Thermal investigation of metal carboxylato complexes of the first transition metals, Mn(II), Fe(II), Fe(III), Co(II), Ni(II) and Cu(II) and non-transition metals like Zn(II) and Cd(II) in the solid state has been carried out under non-isothermal conditions in nitrogen atmosphere by simultaneous TG and DTA. TG and DTA curves inferred that the thermal stability of the complex decreased approximately with the increase of the standard potential of the central metal ion. The thermal parameters like activation energy, E_a, enthalpy change, ΔH, and entropy change, ΔS, corresponding to the dehydration and decomposition of the complexes are determined from TG and DTA curves by standard methods. A linear correlation is found between ΔH and ΔS and E_a and ΔS in dehydration and decomposition processes. DTA curves show an irreversible phase transition for Na₂Mn(mal)₂], Na₂[Cu(mal)₂] and Na₂,[Co(suc)₂] complexes. The residual products in these decomposition processes being a mixture of two oxides, of oxide and carbonate or a mixture of two carbonates.     

A comprehensive assessment on degradation of multi-walled carbon nanotube-reinforced EMA nanocomposites

Thermal degradation kinetics of MWNT-reinforced EMA-based nanocomposites having different methyl acrylate (MA) contents (by % mass) ranging from 9 to 30% have been monitored. Kissinger and Flynn?CWall?COzawa methods for evaluating non-isothermal degradation of polymers have been examined. Overall, the thermal stabilities of the nanocomposites are the function of amount of MWNTs loading and their state of dispersion that depends on the MA content of respective EMAs. Composite samples exhibit higher activation energy (E _a) than the neat EMAs but the E _as of the composites diminish with increased MA contents of the matrices. TG-Mass spectrometry has been used to identify the volatile products resulting from thermal degradation of composites, and a promising mechanism has been proposed over different range of temperatures of degradation. It is proposed that the side-group scission of methoxycarbonyl group initiates thermal decomposition following combination of chain end and random chain scission reactions, ensuing pseudo second-order kinetics.     

Pyrolysis kinetics of elephant grass pretreated biomasses

The Elephant Grass (Pennisetum purpureum Schum) was pretreated by two independent processes, through washing with hot water (W-EG) and acid solution (AW-EG) to improve its energy properties to apply it in a thermochemical process conversion into fuel. The biomasses were analyzed by proximate and ultimate analysis; and the pyrolysis kinetics, before and after pretreatments, were evaluated by the apparent activation energy (E _a) for decomposition in the temperature range of greater volatile matter through the Model-free kinetics using thermogravimetric analysis data. The kinetics of the microcrystalline cellulose Avicel PH-101 was performed to evaluate the E _a result of pure cellulose. The pretreatments were efficient in increasing the volatile matter and heating value, decreasing moisture and ash content, and improving its energetic power to the application in fast pyrolysis process for bio-oil production. The TG results have shown that the reduction in ash content facilitates the pyrolysis process, increasing the volatile matter and decreasing the apparent activation energy required to biomasses degradation, due to less diffusional resistances to heat and mass transfer of W-EG and AW-EG. The Avicel PH-101 showed the highest value of apparent activated energy (E _a = 276.2 kJ mol^?1) which could be explained by its crystallinity, suggesting that crystalline cellulose regions are less accessible to heat diffusion than amorphous regions, requiring more energy to its degradation.     

Thermal study of TiO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> yellow ceramic pigment obtained by the Pechini method

TiO₂–CeO₂ oxides for application as ceramic pigments were synthesized by the Pechini method. In the present work the polymeric network of the pigment precursor was studied using thermal analysis. Results obtained using TG and DTA showed the occurrence of three main mass loss stages and profiles associated to the decomposition of the organic matter and crystallization. The kinetics of the degradation was evaluated by means of TG applying different heating rates. The activation energies (E _a) and reaction order (n) for each stage were determined using Horowitz–Metzger, Coats–Redfern, Kissinger and Broido methods. Values of E _a varying between 257–267 kJ mol^–1 and n=0–1 were found. According to the kinetic analysis the decomposition reactions were diffusion controlled.