(Vapour + liquid) equilibrium in (N,N-dimethylacetamide + methanol + water) at the temperature 313.15 K

Total vapour pressures, measured at the temperature 313.15 K, are reported for the ternary mixture (N,N-dimethylacetamide + methanol + water), and for binary constituents (N,N-dimethylacetamide + methanol) and (N,N-dimethylacetamide + water). The present results are compared with previously obtained data for binary mixtures (amide + water) and (amide + methanol), where amide=N-methylformamide, N,N-dimethylformamide, N-methyl-acetamide, 2-pyrrolidinone and N-methylpyrrolidinone. Moreover, it was found that excess Gibbs free energy of mixing for binary mixtures varies roughly linearly with the molar volume of amide.     

Isothermal vapor-liquid equilibrium at T = 333.15 K and excess volumes and molar refractivity deviation at T = 298.15 K for the ternary mixtures {di-methyl carbonate (DMC) + ethanol + benzene} and {DMC + ethanol + toluene}

Isothermal vapor-liquid equilibrium data at 333.15 K are reported for the ternary systems {di-methyl carbonate (DMC) + ethanol + benzene} and {DMC + ethanol + toluene} as determined with headspace gas chromatography. The experimental ternary vapor-liquid equilibrium (VLE) data were correlated with different activity coefficient models. The excess volume (V^E) and deviations in molar refractivity (ΔR) data are reported for the binary systems {DMC + benzene} and {DMC + toluene} and also for the ternary systems {DMC + ethanol + benzene} and {DMC + ethanol + toluene} at 298.15 K. These V^E and ΔR data were correlated with the Redlich-Kister equation for binary systems and the Cibulka equation for ternary systems.     

Densities, refractive indices and speeds of sound of the ternary mixtures (dimethyl carbonate + methanol + ethanol) and (dimethyl carbonate + methanol + 1-propanol) at T=298.15 K

Density, refractive index and speed of sound at T=298.15 K and atmospheric pressure have been measured over the entire composition range for (dimethyl carbonate (DMC) + methanol + ethanol) and (DMC + methanol + 1-propanol). Excess molar volumes, changes of refractive index on mixing and deviations in isentropic compressibility for the above systems have been calculated. The calculated quantities are further fitted to the Cibulka equation to estimate the ternary fitting parameters. Standard deviations from the regression lines are shown.     

Isothermal vapor–liquid equilibrium at 303.15 K and excess molar volumes at 298.15 K for the ternary system of propyl vinyl ether + 1-propanol + 2,2,4-trimethyl-pentane and its binary sub-systems

Isothermal vapor–liquid equilibrium data determined by the static method at 303.15 K are reported for the binary systems propyl vinyl ether + 1-propanol, 1-propanol + 2,2,4-trimethylpentane and propyl vinyl ether + 2,2,4-trimethylpentane and also for the ternary system propyl vinyl ether + 1-propanol + 2,2,4-trimethyl-pentane. Additionally, new excess volume data are reported for the same systems at 298.15 K. The experimental binary and ternary vapor–liquid equilibrium data were correlated with different G^E models and excess molar volume data were correlated with the Redlich–Kister equation for the binary systems and the Cibulka equation for the ternary system, respectively.     

Density and refractive index measurements of critical mixture 1,4-dioxane + water + saturated KCl in homogenous phase region

The ternary critical mixture of 1,4-dioxane (1) + water (2) + saturated KCl (3) has a lower critical point. The density ρ and refractive index n of this system have been measured as function of temperature for nine critical mixtures along the coexistence curve below the temperature of phase-transition. The water mole fraction in free basis x₂ in the mixtures extends from (0.550 to 0.880) and the molality m of KCl from 0.47 to 2.039 mol kg⁻¹. With increase of temperature, water mole fraction and KCl molality, the obtained density decreased, while the refractive index decreases with increase in temperature, water mole fraction and molality of salt. Both represented anomalies near the critical temperature T_c. The molar fraction of critical mixture, increase less than 1%, with temperature and decrease by 10%, with water mass fraction and molality of salt. The critical density and the critical refractive index vary linearly with water mass fraction w₂$w_2$ with molality m of KCl as a third degree polynomial.     

Isobaric thermal expansivity of the binary system 1-hexanol + n-hexane as a function of temperature and pressure

The isobaric thermal expansivity against temperature and pressure for the system 1-hexanol + n-hexane was directly determined by means of a calorimetric method. From these data, the excess isobaric thermal expansivity is calculated at representative temperatures and pressures. The obtained results for this excess quantity are qualitatively discussed by applying well-known arguments often used for explaining the thermodynamic behavior of alcohol + alkane mixtures. In order to check the consistency of these data with those of literature, the derivative of excess molar volume against temperature and that of excess isobaric molar heat capacity against pressure are calculated and compared with those obtained from literature data. Very good coherence between both data sources is obtained.     

Investigation on isobaric vapor liquid equilibrium for acetic acid + water + (n-propyl acetate or iso-butyl acetate)

Isobaric vapor-liquid equilibrium (VLE) data for acetic acid + water, acetic acid + n-propyl acetate, acetic acid + iso-butyl acetate, acetic acid + water + n-propyl acetate, acetic acid + water + iso-butyl acetate are measured at 101.33 kPa with a modified Rose still. The nonideal behavior in vapor phase caused by the association of acetic acid are corrected by the chemical theory and Hayden-O’Connell method, and analyzed by calculating the second virial coefficients and apparent fugacity coefficients. The VLE data for acetic acid + water, acetic acid + n-propyl acetate, and acetic acid + iso-butyl acetate are correlated through the NRTL and UNIQUAC models using the nonlinear least square method. The obtained NRTL model parameters are used to predict the ternary VLE data. The ternary predicted values obtained in this way agree well with the experimental values.     

Excess molar volumes of N,N-dimethylformamide + 2-pentanone + alkan-1-ols mixed solvent systems at 303.15 K

Accurate excess molar volumes (V^E), at ambient pressure and 303.15 K, have been determined in the ternary liquid mixtures of N,N-dimethylformamide (DMF) + 2-pentanone (PE) + 1-alkan-1-ols (C₃-C₆) and in the binary mixtures of PE + alkan-1-ols (C₃-C₆) as a function of composition. The alkanols include 1-propanol, 1-butanol, 1-pentanol and 1-hexanol. The intermolecular interactions and structural effects were analyzed on the basis of the measured and derived properties. Excess molar volumes increase in magnitude with increase in chain length of alcohol. Valuable information on the behavior and governing factors of the liquid structure of the strongly associated solvents studied were inferred from the parameters deduced. The V^E results were correlated and fitted by the Redlich-Kister equation for binary mixtures and by the Cibulka equation for ternary mixtures, as a function of mole fraction. Several predictive empirical relations were applied to predict the excess volumes of ternary mixtures from the binary mixing data. An analysis of the data indicates a good agreement between experimental results and predicted values in all ternary systems. A discussion is presented and deviations are interpreted in terms of size, shape, the position of ketone group, the chain length of alkanol and hydrogen bond effects in the liquid mixtures studied to explain chemical and thermophysical behavior.     

Excess and deviation properties for the binary mixtures of methylcyclohexane with benzene, toluene, p-xylene, mesitylene, and anisole at T = (298.15, 303.15, and 308.15) K

Experimental data on density, viscosity, and refractive index at T = (298.15, 303.15, and 308.15) K, while speed of sound values at T = 298.15 K are presented for the binary mixtures of (methylcyclohexane + benzene), methylbenzene (toluene), 1,4-dimethylbenzene (p-xylene), 1,3,5-trimethylbenzene (mesitylene), and methoxybenzene (anisole). From these data of density, viscosity, and refractive index, the excess molar volume, the deviations in viscosity, molar refraction, speed of sound, and isentropic compressibility have been calculated. The computed values have been fitted to Redlich-Kister polynomial equation to derive the coefficients and estimate the standard errors. Variations in the calculated excess quantities for these mixtures have been studied in terms of molecular interactions between the component liquids and the effects of methyl and methoxy group substitution on benzene ring.     

Volumetric properties of the water + ethylenediamine mixture at atmospheric pressure from 288.15 to 353.15 K

Densities of the water + ethylenediamine binary system were measured at atmospheric pressure over the whole range of compositions at temperatures from 288.15 to 353.15 K using an Anton Paar digital vibrating glass tube densimeter. Density increases with water content. The experimental excess molar volume data have been correlated with the Redlich-Kister equation, and partial molar volumes calculated at infinite dilution for each component.     

Excess molar enthalpies of the ternary mixtures (1-hexene + tetrahydrofuran or 2-methyltetrahydrofuran + methyl tert-butyl ether) at the temperature 298.15 K

Microcalorimetric measurements of excess enthalpies at the temperature T = 298.15 K are reported for the binary mixture, (x₁C₆H₁₂ + x₂C₄H₈O) and the two ternary mixtures {x₁C₆H₁₂ + x₂(C₄H₈O or C₅H₁₀O) + x₃(C₅H₁₂O)}. Smooth representations of the results are presented and used to construct constant excess molar enthalpy contours on Roozeboom diagrams. It is shown that good estimates of the ternary enthalpies can be obtained from the Liebermann and Fried model, using only the physical properties of the components and their binary mixtures.     

Physical and excess properties of binary and ternary mixtures of 1,1-dimethylethoxy-butane, methanol, ethanol and water at 298.15 K

The ternary systems 1,1-dimethylethoxy-butane (BTBE) + methanol + water and BTBE + ethanol + water have large heterogeneous zones. Experimental densities, refractive indices and speeds of sound have been measured at 298.15 K for mixtures of these systems within the homogeneous zone, and also for methanol + BTBE and ethanol + BTBE binary systems over the entire range of compositions. Excess molar volumes and molar refraction and isentropic compressibility changes of mixing were calculated from the experimental physical properties and were satisfactorily correlated with the corresponding composition data using the Redlich-Kister polynomial. Fitted coefficients and mean standard deviations of correlations have been reported.     

Excess Gibbs energies and volumes of the ternary system chloroform + tetrahydrofuran + cyclohexane at 298.15 K

Vapour–liquid equilibria and densities for the ternary system chloroform + tetrahydrofuran + cyclohexane and for the binary mixtures containing chloroform have been determined at 298.15 K. Vapour–liquid equilibrium data have been collected by head-space gas-chromatographic analysis of the vapour phase directly withdrawn from an equilibration apparatus. Density measurements have been carried out by means of a vibrating tube densimeter. Molar excess Gibbs energies G^E and volumes V^E, as well as activity coefficients and apparent molar volumes of the components, have been obtained from the measured quantities and discussed. The binary chloroform + tetrahydrofuran displays negative deviations from ideality, while chloroform + cyclohexane positive deviations, for both volume and Gibbs energy. The G^E's and V^E's for the ternary system are positive in the region rich in cyclohexane while negative in the region rich in chloroform + tetrahydrofuran. This indicates that hydrogen bonding between chloroform and tetrahydrofuran molecules produces negative values of G^E and V^E and strongly influences the behaviour of the ternary system.     

Vapour pressure and excess Gibbs energy of binary 1,2-dichloroethane + cyclohexanone,chloroform + cyclopentanone and chloroform + cyclohexanone mixtures at temperatures from 298.15 to 318.15 K

The vapour pressures of the binary systems 1,2-dichloroethane + cyclohexanone, chloroform + cyclopentanone and chloroform + cyclohexanone mixtures were measured at temperatures between 298.15 and 318.15 K. The vapour pressures vs. liquid phase composition data for three isotherms have been used to calculate the activity coefficients of the two components and the excess molar Gibbs energies, G^E, for these mixtures, using Barker's method. Redlich–Kister, Wilson, NRTL and UNIQUAC equations, taking into account the vapour phase imperfection in terms of the 2-nd virial coefficient, have represented the G^E values. No significant difference between G^E values obtained with these equations has been observed. Our data on vapour–liquid equilibria (VLE) and excess properties of the studied systems are examined in terms of the DISQUAC and modified UNIFAC (Dortmund) predictive group contributions models.     

(Liquid + liquid) equilibria of {heptane + xylene + N-formylmorpholine} ternary system

(Liquid + liquid) equilibrium (LLE) data for ternary system {heptane (1) + m-xylene (2) + N-formylmorpholine (3)} have been determined experimentally at temperatures ranging from 298.15 K to 353.15 K. Complete phase diagrams were obtained by determining solubility and tie-line data. Tie-line compositions were correlated by Othmer-Tobias and Bachman methods. The universal quasichemical activity coefficient (UNIQUAC) and The non-random two liquids equation (NRTL) were used to correlate the phase equilibrium in the system using the interaction parameters determined from experimental data. It is found that UNIQUAC and NRTL used for LLE could provide a good correlation. Distribution coefficients, separation factors, and selectivity were evaluated for the immiscibility region.     

Molar excess enthalpies of ethyl acetate + alkanols at T = 298.15 K, p = 10.0 MPa

A commercial flow-mixing isothermal calorimeter was tested by measuring heat of mixing curves for exothermic, endothermic, S-shaped and double minimum molar excess enthalpy mixtures at high pressure. The results show this calorimeter is able to produce good quality data. Molar excess enthalpies for ethyl acetate mixed with a series of simple alkanols were measured at T = 298.15 K and p = 10 MPa.     

New isothermal vapor–liquid equilibria for the CO2 + n-nonane,and CO2 + n-undecane systems

Experimental vapor–liquid equilibria (VLE) for the CO₂ + n-nonane and CO₂ + n-undecane systems were obtained by using a 100-cm³ high-pressure titanium cell up to 20 MPa at four temperatures (315, 344, 373, and 418 K). The apparatus is based on the static-analytic method; which allows fast determination of the coexistence curve. For the CO₂ + n-nonane system, good agreement was found between the experimental data and those reported in literature. No literature data were available for the CO₂ + n-undecane system at high temperature and pressure. Experimental data were correlated with the Peng–Robinson equation of state using the classical and the Wong–Sandler mixing rules.     

Phase diagram and thermodynamic modeling of PEO + organic salts + H2O and PPO + organic salts + H2O aqueous two-phase systems

The phase diagrams of PEO1500 + sodium tartrate + water, PPO400 + sodium tartrate + water, PEO1500 + sodium succinate + water, PPO400 + sodium succinate + water, PEO1500 + sodium citrate + water, PPO400 + sodium citrate + water and PPO400 + sodium acetate + water aqueous two-phase systems were determined at (283.15, 298.15, and 313.15) K. Both equilibrium phases composition were analyzed by conductimetry and refractive index. In this paper, the influences of polymer hydrophobicity, salt nature and temperature on the phase diagram were analyzed. The phase separation processes was endothermic and the hydrophobic increase make easier the phase splitting, while the electrolyte capacity to induce phase separation follow the order: citrate > tartrate > succinate. The consistency of the tie-line data was ascertained by applying the Othmer-Tobias correlation. The experimental data were correlated with the NRTL model for the activity coefficient, with estimation of new interaction energy parameters. The results, analyzed in terms of root mean square deviations between experimental and calculated compositions, were considered satisfactory.     

Thermodynamic properties of mixing for (1-alkanol + an-alkane + a cyclic alkane) atT = 298.15 K. I. (n-Hexane + cyclohexane + 1-butanol)

Experimental values of density, refractive index and speed of sound of (hexane  +  cyclohexane  +  1-butanol) were measured at T =  298.15 K and atmospheric pressure. From the experimental data, the corresponding derived properties (excess molar volumes, changes of refractive index on mixing and changes of isentropic compressibility) were computed. Such derived values were correlated using several polynomial equations. Several empirical methods were used in the calculation of the properties of ternary systems from binary data. The Nitta–Chao group contribution model was applied to predict excess molar volume for this mixture.     

Physical properties and phase equilibria of the system isopropyl acetate + isopropanol + 1-octyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide

Densities, refractive indices and dynamic viscosities of binary and ternary mixtures composed of isopropyl acetate, isopropanol, 1-octyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide ([C₈mim][NTf₂]) have been determined at 298.15 K and atmospheric pressure. The excess molar volumes and dynamic viscosity changes of mixing have been calculated and correlated using the Redlich–Kister polynomial equation. Isobaric vapour–liquid equilibrium (VLE) data have been determined experimentally for these binary and ternary systems at 101.32 kPa. The equilibrium data have been adequately correlated by means of Wilson, NRTL, and UNIQUAC equations for the liquid phase activity coefficient.