三氟丙基修饰的二氧化硅膜制备、氢气分离及其水热稳定性能

以三氟丙基三甲氧基硅烷(TFPTMS)和正硅酸乙酯(TEOS)作为前驱体,通过溶胶-凝胶法制备三氟丙基修饰的SiO₂膜材料,研究了三氟丙基修饰对膜材料孔结构和疏水性的作用、疏水膜材料的氢气渗透和分离性能以及水热稳定性能。结果表明三氟丙基修饰后的膜材料仍保持良好的微孔结构,孔径狭窄分布在0.45~0.7 nm之间。修饰后膜材料疏水性明显提高,当n_TFPTMS/n_TEOS=0.6时,对水的接触角达到(102.7°±0.1°)。H₂在修饰后膜材料的输运遵循微孔扩散机理,在300 ℃时,H₂的单组份渗透率达到4.77×10^-7 mol·m^-2·s^-1·Pa^-1,H₂/CO₂的理想分离系数以及双组份分离系数分别达到6.99和6.93,均高于其Knudsen扩散分离因子。在200 ℃水蒸气物质的量含量为5%的环境中陈化220 h后,H₂的单组份渗透率仅在前3 h有轻微下降,然后基本保持不变,说明三氟丙基修饰的SiO₂膜具有良好的水热稳定性。     

十三氟辛基修饰的疏水有机-无机杂化二氧化硅膜孔结构、氢气分离及水热稳定性

采用1,2-双(三乙氧基硅基)乙烷(BTESE)和十三氟辛基三乙氧基硅烷(PFOTES)为前驱体,在酸性条件下通过溶胶-凝胶法制备了十三氟辛基修饰的有机-无机杂化SiO2膜材料。利用接触角测量、红外光谱、动态光散射和N2吸附等测试技术分别对膜材料的疏水性、溶胶粒径和孔结构进行表征,并深入研究有支撑膜材料的氢气渗透、分离性能以及长期水热稳定性。结果表明,十三氟辛基修饰后的膜材料由亲水性变成了疏水性,当nPFOTES/nBTESE=0.6时膜材料对水的接触角达到(110.4±0.4)°,膜材料还保持微孔结构,孔径分布在0.5~0.8 nm。氢气在修饰后的膜材料中的输运遵循微孔扩散机理,在300℃时,氢气的渗透率达到8.5×10-7mol·m-2·s-1·Pa-1,H2/CO2,H2/CO和H2/SF6的理想分离系数分别为5.49,5.90和18.36,均高于相应的Knudsen扩散分离因子。在250℃且水蒸气物质的量分数为5%水热环境下陈化250 h,氢气渗透率和H2/CO2的理想分离系数基本保持不变,膜材料具有良好的水热稳定性。     

苯基修饰的疏水微孔二氧化硅膜的制备与表征

采用苯基三乙氧基硅烷(PTES)和正硅酸乙酯(TEOS)作为前驱体,通过溶胶-凝胶法制备了苯基修饰的SiO2膜材料。利用扫描电镜、N2吸附、视频光学接触角测量仪、热重分析、红外光谱等测试手段对膜的孔结构以及疏水性能进行了表征,最后还研究了修饰后膜材料在室温条件下的单组份气体渗透和分离性能。结果表明,随着PTES加入量的增大,膜材料的疏水性逐渐增强,当PTES/TEOS和H2O/TEOS的化学计量比分别达到0.6和9.6时,膜材料对水的接触角达到115±0.5°,仍保持良好的微孔结构,其孔体积为0.17cm3/g,孔径为0.4-0.5nm。室温下氢气在修饰后SiO2膜的输运既遵循发生在微孔孔道的表面扩散机理也遵循发生在较大孔道或者微缺陷的努森扩散机理,膜材料的H2渗透率达到1.49×10-6mol?m-2?Pa-1?s-1,H2/CO2 和H2/SF6的理想分离系数分别达到4.64和365.59     

三氟丙基修饰的有机-无机杂化二氧化硅膜制备、氢气分离及水热稳定性能

以三氟丙基三甲氧基硅烷(TFPTMS)和1,2-双(三乙氧基硅基)乙烷(BTESE)为前驱体, 通过溶胶-凝胶法在酸性条件下制备三氟丙基修饰的有机-无机杂化SiO₂膜材料, 并深入研究三氟丙基修饰对溶胶粒径和疏水性能的影响以及膜材料的氢气渗透分离性能和长期水热稳定性. 结果表明三氟丙基已成功修饰到有机-无机杂化SiO₂膜材料中, 且随着TFPTMS修饰量的增加, 溶胶粒径有减小趋势, 膜材料的疏水性能逐渐提高. 当n(TFPTMS)/n(BTESE)＝0.6时, 溶胶平均粒径为2.11 nm, 膜材料对水的接触角达到111.6°±0.7°. H₂在修饰后膜材料中的输运主要遵循微孔扩散机理, 300 ℃时H₂的渗透率为8.86×10^-7 mol·m^-2·s^-1·Pa^-1, H₂/CO₂的理想分离系数达到5.4, 且当进气摩尔比例为1∶1时H₂/CO₂的双组分气体分离系数达到了4.82, 均高于Knudsen扩散分离因子(H₂/CO₂＝4.69), 膜材料呈现出良好的分子筛分性能. 膜材料在250 ℃及水蒸气摩尔含量为5%的水热环境中能稳定工作300 h以上.     

表面修饰的有机-无机杂化微孔SiO2膜的制备及氢气分离性能

采用苯基三乙氧基硅烷(PTES)和1,2-双(三乙氧基硅基)乙烷(BTESE)为前驱体, 通过溶胶-凝胶法制备了苯基修饰的有机-无机杂化SiO2 膜材料. 通过N2吸附、视频光学接触角测量、热重分析和红外光谱对膜材料的孔结构和疏水性能进行了表征, 并深入研究了膜材料的氢气渗透和分离性能. 结果表明, 修饰后的膜材料具有微孔结构, 孔径集中分布在0.4~0.6 nm. 在温度为40 ℃, 湿度为70%~80%的水热环境下陈化30 d后, 膜材料仍保持微孔结构. 苯基修饰后膜材料具有疏水性, 当n(PTES)/n(BTESE)=0.6时, 膜材料对水的接触角达到(125±0.4)°. 氢气在膜材料中的输运遵循活化扩散机理, 300 ℃时, 膜材料的H2渗透率达到8.71×10-7mol·m-2·Pa-1·s-1, H2/CO2的理想分离系数达到5.53.     

钴掺杂二氧化硅膜的制备、表征及氢气分离性能

采用正硅酸乙酯(TEOS)和Co(NO3)2.6H2O为前驱体通过溶胶-凝胶法制备掺钴微孔二氧化硅膜,研究钴在二氧化硅膜材料中的存在状态、膜材料孔结构以及膜材料的气体渗透和分离性能。结果表明钴元素以Si-O-Co的形式存在于SiO2骨架之中,掺杂Co 10%的微孔SiO2膜具有典型的微孔结构,其孔体积为0.119 cm3·g-1,平均孔径在0.52 nm左右且孔径主要分布在0.4～0.55 nm之间。氢气在膜材料中的输运低温下遵循Knudsen扩散机理,高于100℃时遵循活化扩散机理,300℃时膜材料的H2渗透率达到6.41×10-7 mol.m-2.s-1.Pa-1,H2/CO2分离系数达到6.61,高于Knudsen扩散的理想分离系数。     

碳氟基团修饰的疏水微孔二氧化硅膜制备与表征

采用三氟丙基三乙氧基硅烷（TFPTES）和正硅酸乙酯（TEOS）作为前驱体,通过溶胶-凝胶法制备了三氟丙基修饰的SiO2膜材料。利用扫描电镜、N2 吸附、 红外光谱仪以及视频光学接触角测量仪对膜的断面形貌、孔结构以及疏水性能进行了表征。结果表明,随着三氟丙基三乙氧基硅烷加入量的增大,膜的疏水性逐渐增强,膜的孔结构基本保持不变。当TFPTES/TEOS的摩尔比例达到0.6时,膜对水的接触角达到 111.6°±0.5º,膜材料仍保持良好的微孔结构,其孔体积为0.19cm3•g-1,孔径为0.97nm。     

十三氟辛基修饰的疏水有机-无机杂化二氧化硅膜孔结构、氢气分离及水热稳定性

采用1,2-双（三乙氧基硅基）乙烷（BTESE）和十三氟辛基三乙氧基硅烷（PFOTES）为前驱体,在酸性条件下通过溶胶-凝胶法制备了十三氟辛基修饰的有机-无机杂化SiO₂膜材料。利用接触角测量、红外光谱、动态光散射和N₂吸附等测试技术分别对膜材料的疏水性、溶胶粒径和孔结构进行表征,并深入研究有支撑膜材料的氢气渗透、分离性能以及长期水热稳定性。结果表明,十三氟辛基修饰后的膜材料由亲水性变成了疏水性,当n_PFOTES/n_BTESE=0.6时膜材料对水的接触角达到（110.4±0.4）°,膜材料还保持微孔结构,孔径分布在0.5~0.8nm。氢气在修饰后的膜材料中的输运遵循微孔扩散机理,在300℃时,氢气的渗透率达到8.5×10^-7mol·m^-2·s^-1·Pa^-1,H₂/CO₂,H₂/CO和H₂/SF₆的理想分离系数分别为5.49,5.90和18.36,均高于相应的Knudsen扩散分离因子。在250℃且水蒸气物质的量分数为5%水热环境下陈化250h,氢气渗透率和H₂/CO₂的理想分离系数基本保持不变,膜材料具有良好的水热稳定性。     

十七氟癸基修饰的有机-无机杂化二氧化硅膜材料的制备及气体分离性能

以十七氟癸基三乙氧基硅烷(PFDTES)和1,2-双(三乙氧基硅基)乙烷(BTESE)为前驱体, 通过溶胶-凝胶法制备了十七氟癸基修饰的SiO₂溶胶, 采用浸渍提拉法在γ-Al₂O₃/α-Al₂O₃多孔陶瓷支撑体上涂膜, 然后在N₂气氛保护下烧结成完整无缺陷的有机-无机杂化SiO₂膜. 利用扫描电子显微镜对膜材料的形貌进行观察, 通过动态光散射技术对溶胶粒径及分布进行测试, 利用视频光学接触角测量仪、 红外光谱仪和热分析仪表征了十七氟癸基修饰对有机-无机杂化SiO₂膜疏水性的影响. 结果表明, 十七氟癸基已经成功修饰到SiO₂膜材料中, 且随着PFDTES加入量的增大, 溶胶粒径和膜材料对水的接触角不断增大. 当n(PFDTES): n(BTESE)=0.25: 1时, 溶胶粒径分布较窄, 平均粒径为3.69 nm, 膜材料对水的接触角为(112.0±0.4)º. 在修饰后的有机-无机杂化SiO₂膜中H₂的输运遵循微孔扩散机理, 在300℃时, H₂的渗透率达到5.99×10^-7 mol·m^-2·Pa^-1·s^-1, H₂/CO和H₂/CO₂的理想分离系数分别达到9.54和5.20, 均高于Knudsen扩散的理想分离因子, 表明膜材料具有良好的分子筛分效应.     

硅烷表面修饰引发的ZnO微米棒膜的超疏水性

采用简单的低温水热法制备出ZnO微米棒薄膜,其经辛基三甲氧基硅烷和十二氟庚基丙基三甲氧基硅烷修饰后显示出超疏水性,静态接触角分别为(150±1.3)°和(155±1.5)°,滚动角依次为5°和3°。 ZnO微米棒的微结构和低表面能材料辛基三甲氧基硅烷、十二氟庚基丙基三甲氧基硅烷的表面修饰是其显示超疏水性的原因,用Cassie理论对膜的润湿性进行了分析。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.