一氧化碳中选择氧化除氢催化剂的研究

Several supported Pd catalysts were prepared and their catalytic activity for selective oxidation of hydrogen was studied. The results show that the variety of the supports has great effect on the catalytic activity. The space velocity and the Pd loading show also certain influence. The most active catalyst Pd/C A can selectively remove H 2 at 170～200℃ and 1?800 h -1 from a feed gas consisting of H 2 (0 197%), O 2 (0 103%), CO (40%) and N 2 (balance). When CO content in the feed gas increases to 78%, the activity of the catalyst only decreases a little, indicating that the results obtained here seems applicable to the removal of H 2 from pure CO.     

CO+H2合成产物中混合醇的色谱分析

在CO_(?) H_(?)催化合成的液相产物中,不仅含有烃和水,还有混合醇及其它含氧化合物。产物分布复杂,对其中的混合醇分析比较困难。文献报道了在柱porapak P上对正构醇分析的情况。本文选用GDX-103柱,峰高法内标工作曲线。对合成产物中低碳混合醇含量进行了测定,结果表明,此方法可以使低碳醇很好分离,数据处理简便,具有一定的可靠性。     

CO2/H2在不同形态ZrO2上的吸附行为

利用傅立叶变换红外光谱技术(FT-IR)考察了CO2和CO2＋H2在不同形态氧化锆上的吸附和转化行为，结果表明,氧化锆的形态影响CO2的吸附形式和表面物种的生成.无定型氧化锆上主要生成碳酸氢盐和离子碳酸盐，单斜氧化锆上还出现了双齿碳酸盐，而在四方氧化锆上出现最强的线式吸附CO2，并生成聚碳酸盐.在氢气存在的条件下，单斜氧化锆上生成甲烷而在四方氧化锆上则生成甲酸盐.     

Rh2CO2/Al2O3上H2吸附及CO和H2共吸附

CO加氢反应机理一直是许多化学工作者感兴趣的课题．Rh催化剂因其优良的性能而被用于 CO加氢机理研     

H2,CO和H2/CO在ZrO2催化剂上吸附行为研究

用insituFTIR法研究了H₂、CO及CO/H₂在ZrO₂表面的吸附行为.结果表明,H₂在ZrO₂表面吸附存在两种形态的羟基(即ZrOH和ZrOHZr),吸附温度增加,羟基数量增加.CO在200℃易与ZrO₂表面羟基作用形成甲酸盐物种,吸附温度升高时,该物种逐渐分解生成CO和ZrOH.当CO和H₂共存时,表面甲酸盐的量明显增加,并随温度增加,逐渐加氢形成甲氧基,最后生成甲烷.甲氧基的加氢过程较慢,所需反应温度也较高,被认为是CO加氢合成醇的速控步骤.     

CO2与HCN,NH3,H2O分子络合物的从头计算研究

用ab initio能量梯度法(3-21G基组)分别优化CO_2与HCN、NH_3、H_2O_3个分子络合物的平衡几何构型。结果表明HCN、NH_3和H_2O中的N或O原子与CO_2中的C原子之间形成较弱的范德华键,三者的范德华键键长分别为0.2865、0.2775、0.2543nm,稳定化能分别为14.8、27.0、31.2kJ·mol~(-1),3个分子络合物的构型都呈T型,对3个分子络合物的稳定化能的能量分解研究表明它们的形成主要靠静电作用能。     

ABO2型复合氧化物上CO-NO的反应性能

以柠檬酸络合法制备了CuCrO2、CuAlO2和CuFeO2等具有铜铁矿结构的ABO2型复合氧化物,并考察了它们在氧化和还原气氛中对CO NO反应的影响. CuAlO2和CuCrO2具有好的催化活性, CuCrO2更具有相当的稳定性,经过氧化和还原条件下的CO NO反应后,体相组成仍然保持不变. CuAlO2在还原条件下,部分被还原生成了零价铜. CuFeO2的催化活性和稳定性较差,在还原气氛中催化CO NO反应过程中,样品被还原,完全转化成了Cu0和CuFe2O4.     

丙炴醇聚合膜对铁在酸性溶液中的缓蚀作用

The formation of polymer film of propargyl alcohol(PA) and its protective ability against corrosion in Fe/H_2SO_4 and Fe/H_2SO_4+H_2S systems have been investigated using impedance measurement. The composition and morphology of the corrosion surface of iron, on which PA polymerized at different bines, were obtained with the aid of SEM and AFM as well as EDX. The results showed that PA polymerized into compact polymer film in Fe/H_2SO_4 and Fe/ H_2SO_4 + H_2S systems, which made iron surface smooth and have a morphologies of regular square structure in microscopic level. In Fe/H_2SO_4 system, macroscopic continuous polymer film of PA was not formed leading to local corrosion on electrode surface. In Fe/H_2SO_4 +H_2S system, the adsorption of H_2S and HS - on electrode surface slowed down the formation of polymer film of PA. However, the iron sulfide, produced after a longer time, increased the continuity of the polymer film of PA and therefore, the polymer film could perform its long-te...更多rm inhibition action.     

Al(2Pu)+H2(X1Σ+g)的分子反应动力学

基于多体展式方法所导出的ＡｌＨ２（Ｘ＾２Ａ１）分析势能函数,用准经典的Ｍｏｎｔｅ－Ｃａｒｌｏ轨迹法对Ａｌ（＾２Ｐｕ）＋Ｈ２（Ｘ＾１∑＾＋ｇ,ｕ＝ｊ＝０）的分子反应动力学过程进行了计算。结果表明,此反应的主产物为交换反应Ａｌ（＾２Ｐｕ）＋Ｈ２（Ｘ＾１∑＾＋ｇ,ｖ＝ｊ＝０）→ＡｌＨ（Ｘ＾１∑＾＋,Ｖ’,ｊ’）＋Ｈ（＾２Ｓｇ）的ＡｌＨ（Ｘ＾１∑＾＋,ｖ’,ｊ’）没有发现ＡｌＨ２（Ｘ＾２Ａ１）的络合物。而     

微量热法研究γ-Mo2N催化剂表面氢的微分吸附热

Differential heats of H 2 adsorption on γ-Mo2N catalysts were studied by using microcalorimetry. Samples with high and medium surface areas (90 and 17 m2•g -1 ) present a homogeneous energetic distribution of surface sites, which corresponds with the preferential orientation of their (200) planes. Molybdenum nitride with low surface area (8 m2•g -1 ) displays a heterogeneous energetic distribution of H 2 adsorption sites. The higher initial differential heat of hydrogen adsorption observed for the low surface Mo nitride was attributed to species adsorbed on surface sites associated with the (111) plane.     

单分子水对H_2O_2+Cl气相反应影响的理论研究

在aug-cc-pVTZ基组下采用CCSD(T)和B3LYP方法,研究了H2O2+Cl反应,并考虑在大气中单个水分子对该反应的影响.结果表明,H2O2+Cl反应只存在一条生成产物为HO2+HCl的通道,其表观活化能为10.21kJ·mol-1.加入一分子水后,H2O2+Cl反应的产物并没有发生改变,但是所得势能面却比裸反应复杂得多,经历了RW1、RW2和RW3三条通道.水分子在通道RW1和RW2中对产物生成能垒的降低起显著的负催化作用,而在通道RW3中则起明显的正催化作用.利用经典过渡态理论(TST)并结合Wigner矫正模型计算了216.7-298.2 K温度范围内标题反应的速率常数.结果显示,298.2 K时通道R1的速率常数为1.60×10-13cm3·molecule-1·s-1,与所测实验值非常接近.此外,尽管通道RW3的速率常数kRW3比对应裸反应的速率常数kR1大了46.6-131倍,但该通道的有效速率常数k'RW3却比kR1小了10-14个数量级,表明在实际大气环境中水分子对H2O2+Cl反应几乎没有影响.     

CH2(X 3B1)自由基与N2O反应的研究

The reaction dynamics of methylene radical CH2(X3B1) with N2O was investigated by Time-Resolved Fourier Transform Infrared Spectroscopy(TR-FTIRS). Pure CH2(X3B1) radicalwas produced via laser photolysis of ketene at 351 nm. Nascent viabrationally excited products CO, NO and HCN were observed. Some reaction pathways which may lead to these products were proposed and a possible reaction mechanism was outlined.     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

C2H3自由基与O2反应的红外发射光谱及反应通道

The reaction of vinyl radicals with oxygen was investigated by Time-Resolved Fourier Transform infrared emission spectroscopy. The radicals were produced by the pulsed laser photolysis of C_2H_3Br at 248 nm. Vibrationally excited products of H_2CO(v1), HCO(v3), CO_2(v3, v), CH_3(v3), C_2H_2(v3), HO_2(v1), C_2H_2O_2(v3+v11), CO(v) formed in the C2H3+O_2 reaction have been observed. Four elementary reaction channels have been verified.     

(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇结构及其热力学性质

用HF自洽场理论和密度泛函理论(DFT)的B3LYP方法,在6 31G水平上研究了低聚物(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇的几何构型、电子结构和聚合反应热力学性质,比较了两个系列化合物中化学键的强度.结果表明,Cl2AlNH2和H2AlNH2分子为C2 (EC)平面型结构,其中Al－N为由一个σ键和一个键组成的双键.(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)分子为Dnh对称,Al－N是典型的σ单键 .低聚物(Cl2AlNH2)n和(H2AlNH2)n的稳定性顺序分别为: 3 > 2 > 4> 5 > 1和8 > 7 > 9 > 11 > 6.     

真空辅助法合成Fe_3(PO_4)_2·8H_2O及对LiFePO_4/C结构、形貌和电化学性能的影响(英文)

采用了一种真空辅助沉淀法制备Fe3(PO4)2·8H2O,并以此进一步合成粒径尺寸在400 nm左右LiFePO4颗粒.研究了Fe3(PO4)2·8H2O对于磷酸铁锂的形貌、结构、电化学性能的影响.X射线衍射(XRD)结果表明,真空辅助制备的Fe3(PO4)2·8H2O具有高纯度,以此制备的LiFePO4具有高结晶度和纯度.扫描电子显微镜(SEM)结果表明,真空辅助制备的Fe3(PO4)2·8H2O具有未完全发育的颗粒,以此制备的LiFePO4均匀无硬团聚.透射电子显微镜(TEM)结果显示真空辅助制备的LiFePO4包覆一层均匀的碳.真空制备的LiFePO4显示了优异的电化学性能,在1C、10C、20C倍率下的容量分别为140、113、100 mAh·g-1.真空制备的LiFePO4的循环伏安曲线显示了小的极化电压和尖锐的氧化峰.充放电平台曲线表明真空对LiFePO4高倍率性能起到重要作用.电化学阻抗谱(EIS)计算结果显示,真空和非真空制备的LiFePO4的锂离子扩散系数分别为1.42×10-13和4.22×10-14cm2·s-1,说明真空辅助能够提高LiFePO4的扩散系数.