Waveguides in lithium niobate fabricated by focused ultrashort laser pulses

We report on investigations of the bulk microstructuring of lithium niobate crystals with intense femtosecond laser pulses. In different crystal cuts, optical waveguides were produced whose properties depend strongly on the processing parameters. To explore the origin of the refractive index changes, we subjected the crystals to different conditions (like temperature, illumination, etc.) while monitoring the waveguide output. This way several mechanisms for the change in refractive index could be singled out. These include the photorefractive effect, inhomogeneous ion concentrations and stress in the crystalline lattice. As an application, we demonstrate frequency doubling of 1064 nm laser radiation in a microstructured phase-matched waveguide.     

Fabrication of complex nanostructures on ZnO crystals by the interference of three femtosecond laser beams

By adjusting the laser polarization combinations, fluences and pulse numbers, we fabricated several types of two-dimensional (2D) complex nanostructures on the surface of c-cut ZnO single crystal by the interference of three femtosecond laser beams with central wavelength of 800 nm, pulse duration of 50 fs and pulse repetition frequency of 1 kHz. The hexagonal 2D nanostructures with a period of 600 nm are very regular and uniform, in which nanoparticles, nanorings and nanoripples with sizes of 200 nm are embedded. Excited by 800 nm femtosecond laser pulses, the photoluminescence (PL) micrographs reveal that the 2D nanostructures can emit purer and brighter blue light compared with the plane surface. These nanostructures have potential applications in blue light-emitting diodes (LEDs), high density optical storage and other optoelectronic devices.     

Flexible gratings fabricated in polymeric plate using femtosecond laser irradiation

Flexible gratings embedded in poly-dimethlysiloxane (PDMS) were fabricated using femtosecond laser pulses. Photo-induced gratings in a flexible PDMS plate were directly written by a high-intensity femtosecond (130 fs) Ti: Sapphire laser (λ_p=800 nm). Refractive index modifications with 4 μm diameters were photo-induced after irradiation of the femtosecond pulses with peak intensities of more than 1×10¹¹ W/cm². The graded refractive index profile was fabricated to be symmetric around the center of the focal point. The diffraction efficiency of the grating samples is measured by an He-Ne laser. The maximum value of refractive index change (Δn) in the laser-modified regions was estimated to be approximately 3.17×10⁻³.     

Fabrication of micro-gratings on Au-Cr thin film by femtosecond laser interference with different pulse durations

We encoded surface relief micro-gratings on Au-Cr thin films using two-beam interference of femtosecond laser pulses with the durations from 25 fs to 70 fs. The dependence of the fabrication quality on the pulse duration has been investigated both numerically and experimentally. The results revealed that the shorter pulses were preferable to prepare periodical microstructures with minimal ablation fringe width and satisfied fabrication quality. This work has potential applications on periodic functional microstructures fabrication for ultra-fine processing and modification on various materials, especially for intractable materials.     

Periodic surface nanostructures on polycrystalline ZnO induced by femtosecond laser pulses

Periodic surface nanostructures induced by femtosecond laser pulses on polycrystalline ZnO are presented. By translating the sample line-by-line under appropriate irradiation conditions, grating-like nanostructures with an average period of 160 nm are fabricated. The dependence of surface morphologies on the processing parameters, such as laser fluence, pulse number and laser polarization, are studied by scanning electronic microscope (SEM). In addition, photoluminescence (PL) analysis at room-temperature indicates that the PL intensity of the irradiated area increases significantly compared with the un-irradiated area. Using femtosecond laser pulses irradiation to fabricate periodic surface nanostructures on polycrystalline ZnO is efficient, simple and low cost, which shows great potential applications in ZnO-based optoelectronic devices.     

Talbot effect under illumination of double femtosecond laser pulses

The Talbot effect under illumination of double femtosecond laser pulses has been reported. Spectrums of double femtosecond laser pulses with phase differences are quite different from that of one single femtosecond laser pulse. Therefore, the Talbot images of the double femtosecond laser pulses with phase differences are different from that of one single femtosecond laser pulse. Specifically, for the phase difference corresponding to π, the Talbot image shows the largest difference from that of one single pulse. Experimental results are in good agreement with the theoretical analysis. The behaviors of Talbot images under double femtosecond laser pulses illumination cannot be obtained under one femtosecond laser pulse, monochromatic or polychromatic light illumination. Therefore, it is a new interesting optical phenomenon for the Talbot effect which should have potential applications.     

3D features of modified photostructurable glass-ceramic with infrared femtosecond laser pulses

The exclusive ability of laser radiation to be focused inside transparent materials makes lasers a unique tool to process inner parts of them unreachable with other techniques. Hence, laser direct-write can be used to create 3D structures inside bulk materials. Infrared femtosecond lasers are especially indicated for this purpose because a multiphoton process is usually required for absorption and high resolution can be attained. This work studies the modifications produced by 450 fs laser pulses at 1027 nm wavelength focused inside a photostructurable glass-ceramic (Foturan^®) at different depths. Irradiated samples were submitted to standard thermal treatment and subsequent soaking in HF solution to form the buried microchannels and thus unveil the modified material. The voxel dimensions of modified material depend on the laser pulse energy and the depth at which the laser is focused. Spherical aberration and self-focusing phenomena are required to explain the observed results.     

Self-assembled volume vortex grating induced by femtosecond laser pulses in glass

We presented a microfabrication process for optical volume vortex grating inside glass by femtosecond laser pulses. The self-trapped filament of femtosecond laser pulses can induce hundreds μm-long region refractive-index changes in glass. We realized the restructured optical vortex beams using a collimated He–Ne laser beam. The maximum first-order diffraction efficiency was about 19.6%. The volume vortex grating structure fabricated in glass is polarization dependent.     

Surface texturing of the carbon steel AISI 1045 using femtosecond laser in single pulse and scanning regime

Surface texturing of the metals, including steels, gained a new dimension with the appearance of femtosecond lasers. These laser systems enable highly precise modifications, which are very important for numerous applications of metals. The effects of a Ti:sapphire femtosecond laser with the pulse duration of 160 fs, operating at 775 nm wavelength and in two operational regimes - single pulse (SP) and scanning regime, on a high quality AISI 1045 carbon steel were studied. The estimated surface damage threshold was 0.22 J/cm² (SP). Surface modification was studied for the laser fluences of 0.66, 1.48 and 2.37 J/cm². The fluence of 0.66 J/cm², in both working regimes, induced texturing of the material, i.e. formation of periodic surface structures (PSS). Their periodicity was in accordance with the used laser wavelength. Finally, changes in the surface oxygen content caused by ultrashort laser pulses were recorded.     

Investigation on femtosecond laser irradiation energy in inducing hydrophobic polymer surfaces

This study investigates the use of ultrashort femtosecond laser pulses to induce hydrophobic properties on PMMA surfaces. The modification of surface wetting property exhibits a strong dependence on the amount of energy deposited on the PMMA surface. A simple equation has been deduced from the laser parameters to express the energy deposition. It was revealed that water contact angle (WCA) of more than 120°, with a maximum of around 125°, could be achieved when the total energy deposited per unit area on the PMMA surface ranged from 600 J/cm² to 900 J/cm² at an energy deposition rate of around 50 J/cm²/s. Beyond this range, WCA reduced with increasing amount of energy deposition. Furthermore, with higher energy deposition rate or higher laser fluence, total energy required to induce hydrophobic surfaces was reduced. Under different energy deposition, the quantity of polar groups or non-polar groups induced was responsible for the changes in WCA and thus the different surface hydrophobicity.     

Generation of regular femtosecond pulses in AlGaInP semiconductor laser

It is shown experimentally that stable ~ 200 fs regular pulses and optical frequency comb spectrum containing ~ 70 discrete frequencies can be achieved using semiconductor injection laser working in the conditions of superfluorescence under dc pumping current, which is lower than the threshold of laser action.     

Surface ablation of lithium tantalate by femtosecond laser

We report measurements of the laser induced breakdown threshold in lithium tantalate with different number of pulses delivered from a chirped pulse amplification Ti: sapphire system. The threshold fluences were determined from the relation between the diameter D² of the ablated area and the laser fluence F₀. The threshold of lithium tantalite under single-shot is found to be 1.84 J/cm², and the avalanche rate was determined to be 1.01 cm²/J by calculation. We found that avalanche dominates the ablation process, while photoionization serves as a free electron provider.     

Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

Dispersion and compensation of temporal pulse width for femtosecond pulse laser ranging

We built an atmosphere dispersion model of femtosecond laser pulses that can calculate temporal pulse width travelling in air. The initial pulse duration of 100 fs can be broadened to 60 ps when propagating 200 km in the atmosphere. An experimental system has been established to compensate the large dispersion propagating 200 km in the atmosphere. The single model fiber (SMF) and the prism pairs were, respectively, used for coarse and fine compensation in the system. The pulse duration was consistently regulated 150 fs by moving the distance of prism pairs. This method can reach submicron resolution for a long distance by means of time of flight measurement.     

Multipulse irradiation of silicon by femtosecond laser pulses: Variation of surface morphology

The multipulse interaction of ultraviolet femtosecond laser pulses with silicon and generation of surface structures in a large area spot (?1 mm²) has been studied. The evolution of multiscale structures at the constant fluence strongly depends on the number of pulses, N. For N < 200, the “carpet-like” pattern of nano-, and micro-spikes is generated by the bubble explosion in a thin surface foam layer. The accumulation of bubbles and their explosion due to repetition of laser pulses cause damped membrane-like oscillations of the silicon surface. For 200 ≤ N, bifurcation of surface morphology takes place: (i) the surface tension waves of the wavelength ∼200 μm appear in the peripheral region of the spot. Generated by the surface thermal gradient in the liquid foam layer, they spread from the hot centerline towards the periphery of the spot. The change of their wavelength with propagation distance indicates onset of the Eckhaus instability caused by the phase modulation in multipulse interaction. (ii) Deep caverns appear in a highly superheated silicon layer in the central region of the spot due to the fast gas-liquid phase separation and the fragmentation process.     

Superhydrophobic surfaces fabricated by microstructuring of stainless steel using a femtosecond laser

Fabrication of superhydrophobic surfaces induced by femtosecond laser is a research hotspot of superhydrophobic surface studies nowadays. We present a simple and easily-controlled method for fabricating stainless steel-based superhydrophobic surfaces. The method consists of microstructuring stainless steel surfaces by irradiating samples with femtosecond laser pulses and silanizing the surfaces. By low laser fluence, we fabricated typical laser-induced periodic surface structures (LIPSS) on the submicron level. The apparent contact angle (CA) on the surface is 150.3°. With laser fluence increasing, we fabricated periodic ripples and periodic cone-shaped spikes on the micron scale, both covered with LIPSS. The stainless steel-based surfaces with micro- and submicron double-scale structure have higher apparent CAs. On the surface of double-scale structure, the maximal apparent CA is 166.3° and at the same time, the sliding angle (SA) is 4.2°.     

Spectral modulation of ultra-broadband femtosecond laser pulses based on surface plasmon resonance

The surface plasmon resonance (SPR) for spectral modulation of the femtosecond laser pulses with 110 nm ultra-broad bandwidth is demonstrated on the basis of the development of ultrashort pulse laser sources which supports good spatial resolution and high peak intensity. Employing the femtosecond surface plasmon polariton pulses launched by a Kretschmann configuration, whose reflectivity curve has the characteristic of the ultra-broad bandwidth, we observe a frequency-dependent loss with greater attenuation at the peak of the spectrum profile than in the wings, which is very useful for adequate spectral modulation. The SPR for the spectral modulation is investigated in theoretical and experimental aspects. The arbitrary spectral modulation of the femtosecond laser pulses can be fulfilled by controlling and optimizing the SPR of the gold film. The experimental result agrees well with the calculation.     

Large negative refractive index modification induced by irradiation of femtosecond laser inside optical glasses

We report on the refractive index modification (Δn) and its cross sectional profile of the created lines inside the different types of optical glasses, containing BaO, TiO₂, or La₂O₃ as a metal oxide. The lines were fabricated by scanning a stage and focusing the femtosecond laser pulses, 800 nm wavelength, a 250 kHz repetition rate and 200 fs pulse duration, from the Ti:sapphire regenerative amplifier system. The Δn measurements were performed with the qualitative phase microscopy technique. As a result, it was found that the Δn and its sign are different depending on glass types. For example, in the glasses containing TiO₂, the Δn became smaller in the modified region and some of them showed relatively large decrease of the Δn, Δn < −0.01, with about 10 μm width. Such a glass material could be useful for the compact optics and optical devices.     

Laser-active colour centres with functional periodic structures in LiF fabricated by two interfering femtosecond laser pulses

We report a new technique to fabricate both laser-active F₂ and F₃⁺ colour centres in lithium fluoride and permanent periodic gratings with fringe spacings as fine as sub-micron size simultaneously by two interfering infrared femtosecond (fs) laser pulses. In particular, the optical properties of such colour centres produced by a single fs laser pulse are compared with those created by damage from radiation such as X-rays. Moreover, the present technique is applied to the first production of three-dimensional active channel waveguide and a pulsed distributed-feedback (DFB) laser at around 700 nm in LiF containing F₂ colour centres with fine-pitched micro-grating structures.     

Alcohol-assisted photoetching of silicon carbide with a femtosecond laser

Femtosecond lasers have proved to be effective tools for micromachining silicon carbide material. In the drilling process, however, when the debris around the hole was not removed efficiently, the depth of hole would not increase further. In this paper, alcohol-assisted photoetching of 6H silicon carbide was investigated using a femtosecond laser. Machining in the presence of alcohol was beneficial to the debris ejection from the hole. The alcohol flow and volatilization was also helpful to further carry away the ablation debris and reduce the ablated material redeposition. The experiment showed that photoetching assisted by alcohol produced cleaner ablation effect and deeper hole than in ambient air. Moreover, alcohol assistance would not produce additional thermal damage around the hole. Vias were formed in a 250 μm thick wafer with alcohol-assisted photoetching technique using a femtosecond laser, which demonstrated the potential for this processing technique.