5 μm laser source for frequency metrology based on difference frequency generation

A narrow-linewidth cw 5 μm source based on difference frequency generation of a 1.3 μm quantum dot external cavity diode laser and a cw Nd:YAG laser in periodically poled MgO:LiNbO(3) has been developed and evaluated for spectroscopic applications. The source can be tuned to any frequency in the 5.09-5.13 μm range with an output power up to 0.1 mW, and in the 5.42-5.48 μm range with sub-microwatt output. The output frequency is stabilized and its value determined by measuring the frequency of the two lasers with a remotely located frequency comb. A frequency instability of less than 4 kHz for long integration times and a linewidth smaller than 700 kHz were obtained.     

6.2 W laser-diode end-pumped continuous-wave Nd:YALO3 laser at 1.34 μm

We report a compact and efficient LD end-pumped linearly polarized Nd:YAP laser operating at 1.34 μm. The laser system with different crystal lengths, output couplers and cavity types were compared. Based on optimizing of the pump system and laser cavity, 6.2 W laser radiation at 1341.4 nm with c-axis polarized was achieved, corresponding to an optical conversion efficiency of about 24.8% with respect to the incident pump power. The laser threshold was only about 1.3 W and the optical slope efficiency was up to 27.2%.     

High-power 3.8 μm tunable optical parametric oscillator based on PPMgO:CLN

The experimental results of a high-power 3.8 μm tunable laser are presented on a quasi-phase-matched single-resonated optical parametric oscillator in PPMgO:CLN pumped by a 1064 nm laser of an elliptical beam. Theoretical analyses of the PPMgO:CLN wavelength tuning are presented. The pump source was an acousto-optical Q-switched cw-diode-side-pumped Nd:YAG laser. The beam polarization matched the e-ee interaction in PPMgO:CLN. When the crystal was operated at 90 °C and the pump power was 150 W with a repetition rate of 10 kHz, average output power of 22.6 W at 3.86 μm and 63 W at 1.47 μm was obtained. The slope efficiency of the 3.86 μm laser with respect to the pump laser was 17.8%. The M² factors of the 3.86 μm laser were 1.74 and 4.86 in the parallel and perpendicular directions, respectively. The mid-IR wavelength tunability of 3.7-3.9 μm can be achieved by adjusting the temperature of a 29.2 μm period PPMgO:CLN crystal from 200 °C to 30 °C, which basically is accorded with the theoretic calculation.     

26.3-W continuous-wave, diode-double-end-pumped all-solid-state Nd:GdVO4 laser operating at 1.34 μm

A high-power continuous-wave (CW) all-solid-state Nd:GdVO₄ laser operating at 1.34 μm is reported here. The laser consists of a low doped level Nd:GdVO₄ crystal double-end-pumped by two high-power fiber-coupled diode lasers and a simple plane-parallel cavity. At an incident pump power of 88.8 W, a maximum CW output of 26.3 W at 1.34 μm is obtained with a slope efficiency of 33.7%. To the best of our knowledge, this is the highest output at 1.34 μm ever generated by diode-end-pumped all-solid-state lasers.     

A novel 2-μm pulsed fiber laser based on a supercontinuum source and its application to mid-infrared supercontinuum generation

A new method to achieve 2-μm pulsed fiber lasers based on a supercontinuum(SC) is demonstrated. The incident pump light is a pulsed SC which contains a pump light and a signal light at the same time. The initial signal of the seed laser is provided by the incident pump light and amplified in the cavity. Based on this, we obtain a 2-μm pulsed laser with pulse repetition rate of 50 kHz and pulse width of 2 ns from the Tm-doped fiber laser. This 2-μm pulsed laser is amplified by two stages of fiber amplifiers, then the amplified laser is used for mid-infrared(mid-IR) SC generation in a 10-m length of ZrF4–BaF2–LaF3–AlF3–NaF(ZBLAN) fiber. An all-fiber-integrated mid-IR SC with spectrum ranging from 1.8 μm to4.3 μm is achieved. The maximal average output power of the mid-IR SC from the ZBLAN fiber is 1.24 W(average output power beyond 2.5 μm is 340 mW), corresponding to an output efficiency of 6.6% with respect to the 790-nm pump power.     

Electro-optic Q-switched intracavity optical parametric oscillator at 1.53 μm based on KTiOAsO4

An eye-safe, high peak power optical parameter oscillator (OPO) intracavity pumped by electro-optic Q-switched Nd:YAG laser is presented. This OPO is based on a 20 mm length KTiOAsO₄ crystal with non-critical phase matching (θ = 90°, ?=0°) cut. An aperture ∅3 mm acted as limiting diaphragm to get good beam quality of pumping laser. The output energy of 25 mJ at the signal wavelength 1.53 μm was obtained with repetition rate of 1 Hz. The highest peak power intensity was up to 88 MW/cm² with pulse width of 4 ns. Without diaphragm, the maximum output energy of 90 mJ was achieved with area of light spot (∅6 mm) four times larger, but the peak power intensity was lower.     

Continuous-tunable 4.144-4.851 μm twin-MgO:PPLN cascaded optical parametric generator pumped by a 1.342 μm Nd:GdVO4 laser

An all-solid-state mid-infrared optical parametric generator with wide tunability by using multi-grating periodically poled 5 mol.-% MgO-doped lithium niobate (MgO:PPLN) is reported. The pump source is a diode-pumped Q-switched Nd:GdVO₄ laser operated at 1.342 μm with pulse width of 150 ns and repetition rate of 50 kHz. To extend the interaction length, two identical multi-grating MgO:PPLN crystals have been cascaded in the OPG system. When the incident pump average power is 10 W, the obtained maximum idler output power is 340 mW at 4.144 μm. Compared with only using one multi-grating MgO:PPLN crystal, the obtained idler output power increases by 20.1%. 4.144-4.851 μm continuous-tunable idler output is obtained with six grating periods from 29 to 31.5 μm and temperature from 40 to 200 °C. To our knowledge, this is the first time to use 1.342 μm laser as the pump source of OPG.     

Measurement of free SO2 in wine with 7.4-μm difference frequency spectrometer

A 7.4-μm difference frequency spectrometer is used for analysing the headspace above the liquid surface of a sample of red wine for SO₂. The analysis is based on previously determined line parameters for a number of SO₂ lines of the ν₃ band, and allows fast, interference-free determination of the concentration without the need for any calibration against a standard of known concentration. The potential for developing this technique into a method for determining free and total sulphur dioxide in beverages is discussed. Received: 16 January 2003 / Revised version: 19 February 2003 / Published online: 9 April 2003 RID="*" ID="*"Corresponding author. Fax: +45-4593/1137, E-mail: jh@dfm.dtu.dk     

Investigation on achieving the diode-pumped weak line laser at 1.3 μm

In this paper, a continuous-wave (CW) diode-side-pumped Nd:YAlO₃ (Nd:YAP) laser operating at the weak line of 1339 nm has been achieved and investigated. The output of the 1339 nm laser was realized based on the polarization selection and reasonable transmittance design. The relationship between the output powers and resonator lengths of the 1339 nm Nd:YAP laser has been studied and the optimum resonator length was adopted to improve the output power. As high as 31.3 W output power of the a-axis polarized 1339 nm laser has been obtained at the pumping power of 555 W with the optical-optical and slope efficiencies to be 5.6% and 13%, respectively. This work will provide an effective way to obtain the weak line lasers for potential applications in spectroscopy, coherent terahertz generation, etc.     

Mid-infrared optical parametric oscillator based on ZnGeP2 pumped by 2-μm laser

We present a 3 5 μ m optical parametric oscillator (OPO) based on ZGP pumped by KTP OPO 2.1-μ m laser. The tuning curves of ZGP OPO are calculated. The 8 ×6 ×18 (mm) ZGP crystal, whose end faces are antireflection coated at 2.1 and 3.7 4.6 μ m, is cut as θ =53.5°, φ =0°. When the pump power of 2.1-μ m polarized laser is 15 W at 8 kHz, 5.7-W output power and 46.6% slope efficiency are obtained with a ZGP type I phase match. Central wavelengths of the signal and idler lasers are 4.10 and 4.32 μ m, respectively. Pulse duration is about 27 ns. Beam quality factor M 2 is better than 1.8. The tunability of 3 5 μ m can be achieved by changing the angle of the ZGP crystal.     

New combination bands in CCH2 around 0.83 μm recorded using FT-ICLAS

Fourier-transform intracavity laser absorption spectroscopy allowed five ¹²C¹³CH₂ Σ⁺-Σ⁺ bands, all from the ground state, to be identified in the 0.83 μm range. Their rotational analysis was performed and rotational constants are provided. Three of these bands, with origins at 11616.9684(18), 11737.2356(14), and 11761.0322(23) cm⁻¹, have never been reported before. Their upper states are assigned to , respectively.     

Compact and tunable mid-infrared source based on a 2 μm dual-wavelength KTiOPO4 intracavity optical parametric oscillator

Using a double resonant KTiOPO 4 (KTP) intracavity optical parametric oscillator operating at degenerated point of 2 μm,we demonstrate a unique mid-infrared source based on difference frequency generation in GaSe crystal.The output tuning range is 8.42-19.52 μm,and a peak power of 834 W for type-I phase matching scheme and 730 W for type-II phase matching scheme are achieved.Experimental results show that this oscillator is a good alternative to the generator of a compact and tabletop mid-infrared radiation with a widely tunable range.     

2-μm mode-locked nanosecond fiber laser based on MoS_2 saturable absorber

We demonstrated a 2-μm passively mode-locked nanosecond fiber laser based on a MoS_2 saturable absorber(SA).Owing to the effect of nonlinear absorption in the MoS_2 SA, the pulse width decreased from 64.7 to 13.8 ns with increasing pump power from 1.10 to 1.45 W. The use of a narrow-bandwidth fiber Bragg grating resulted in a central wavelength and 3-dB spectral bandwidth of 2010.16 and 0.15 nm, respectively. Experimental results show that MoS_2 is a promising material for a 2-μm mode-locked fiber laser.     

A near-infrared acetylene detection system based on a 1.534 μm tunable diode laser and a miniature gas chamber

A near-infrared (NIR) dual-channel differential acetylene (C₂H₂) detection system was experimentally demonstrated based on tunable diode laser absorption spectroscopy (TDLAS) technique and wavelength modulation spectroscopy (WMS) technique. A distributed feedback (DFB) laser modulated by a self-developed driver around 1.534 μm is used as light source. A miniature gas chamber with 15 cm path length is adopted as absorption pool, and an orthogonal lock-in amplifier is developed to extract the second harmonic (2f) signal. Sufficient standard C₂H₂ samples with different concentrations were prepared, and detailed measurements were carried out to study the detection performance. A good linear relationship is observed between the amplitude of the 2f signal and C₂H₂ concentration within the range of 200–10,000 ppm, and the relative measurement error is less than 5% within the whole range. A long-term monitoring lasting for 20 h on a 1000 ppm C₂H₂ sample was carried out, and the maximum concentration fluctuation is less than 2%. Due to the capability of using long-distance and low-loss optical fiber, the gas-cell can be placed in the filed for remote monitoring, which enables the system to have good prospects in industrial field.     

Investigation of 1.06 μm laser induced plasma in air using optical interferometry

The laser produced plasma in air by Q-switch Nd:YAG pulses with 50 mJ and 7 ns was analyzed using Mach-Zehnder interferometer. The interferograms were taken at various delay times after single pulses induced gas breakdown. The 3D electron density distribution at early times of the plasma is investigated. To determine the 3D electron density distribution of the plasma, the FFT analysis is applied to extract the phase of the reconstructed interferograms and the numerical inverse Abel transformation is used to calculate the refractive index. The results provide an understanding of the electron density temporal and spatial evolution of laser induced plasma in air from 18 ns and up to 100 ns of plasma lifetime.     

Non-universal dielectric relaxation in SrFeO3 − δ

SrFeO_3 − δ compound is prepared by the thermal decomposition method followed by ball milling. Analysis of Mössbauer spectrum and X-ray diffraction study proves the presence of multi-phase nature, i.e., Sr₈Fe₈O₂₃ and Sr₄Fe₄O₁₁ phases at room temperature. Furthermore, the Mössbauer spectrum at room temperature evidenced the presence of major Fe^3.5+ which is the resultant of equal contributions of Fe⁴⁺ and Fe³⁺. The Nyquist plot at all measured temperatures (80–230 K) suggests that the dielectric response is well associated with single relaxation time (exponential parameter, n∼1$n\sim 1$) i.e., the Debye-type. Modulus analysis exhibits the non-universal dielectric behaviour (stretched exponential parameter, β>1$\beta >1$) below 230 K and the Debye-type responds (β∼1$\beta \sim 1$) at and above 230 K. The Debye-type behaviour exhibited by SrFeO_2.81 at around room temperature in its defect state offers a new opening for this material for multifunctional applications.     

Surface studies of 2,4-pentanedione on γ-Al2O3/NiAl (1 0 0) and NiAl (1 0 0)

The chemical compound 2,4-pentanedione (Hacac) has been shown to etch the oxidized metal surfaces metals such as copper and nickel, but not their unoxidized surfaces. Here it is shown that on the γ-Al₂O₃/NiAl (1 0 0) surface (oxidized NiAl (1 0 0)) etching of aluminum occurs at 170 K and 750 K. Reflection-absorption infrared spectroscopy (RAIRS) is used to show that Hacac binds to both the clean, metallic and oxidized surfaces, but decomposition and combustion products dominate on the metallic surface and no etching occurs. The binding process that involves a deprotonation reaction of the enol species was identified by redshift in the carbonyl peaks and the appearance of an Al-H peak observed in the IR spectrum. The implication of these results is that there is both an unusual low temperature and high temperature etching of the alumina by bound acac.     

Oxidation mechanism and ferryl domain formation on the α-Fe2O3 (0 0 0 1) surface

Recent experimental evidence calls for a reinterpretation of the oxidized structure in chemically distinct domains of the hematite (0 0 0 1) surface as the ferryl (FeO) termination rather than the bulk terminated O₃-Fe-Fe-R structure. Although this interpretation is consistent with experimental data and ab initio thermodynamics calculations, it raises serious questions about how molecular oxygen can be dissociated on a surface where reactive iron centers are slightly more than 5 Å apart. Here, we propose a novel cooperative bimolecular mechanism that provides a reasonable pathway for the formation of the unusual ferryl surface termination and should be readily reversible, which is important for understanding the function of hematite surfaces as an oxidation catalyst.