Remotely pumped hybrid double-pass L-band optical amplifier utilizing chirped fiber Bragg

This paper reported an investigation of remotely pumped double pass L-band amplifier with dispersion compensation technique. The proposed design used chirped fiber Bragg grating (CFBG) to reflect the amplified signal back into the active medium, compensate the effect of fiber dispersion and block the recycled forward amplified spontaneous emission (ASE) and the residual 1480 nm pump power. The characterization of the design was done experimentally. The gain is 37.5 dB and noise figure is 4 dB with best BER of 10⁻⁵² is achieved when the EDF is placed 150 km away from the transmitter and 48 km before the receiver terminal.     

Gain-clamped dual-stage L-band EDFA by using backward C-band ASE

A dual-stage L-band gain-clamped erbium-doped fiber amplifier (GC-EDFA) by using backward C-band amplified spontaneous emission (ASE) is proposed. Compared with other similar GC-EDFAs, the proposed structure has higher and flatter clamped gain in L-band because of its optimal pump power and EDF length. The flatness from 1570 nm to 1600 nm arrives 0.77 dB, the bandwidth of 3 dB is more than 35 nm and the maximal input signal power arrives −15 dBm.     

基于半导体光放大器的一阶IIR微波光子学滤波器及其品质因素分析

对基于半导体光放大器(SOA)环形腔结构的一阶无限冲击响应(IIR)微波光子学滤波器的品质因数(Q值)进行了实验和理论研究. 通过在有源环内置入窄带光滤波器,并调节有源环的输入光功率、SOA抽运电流、实验得到的最高Q值接近200. 理论分析表明为了得到较高的Q值,应尽可能提高信噪比和信号光的环路增益. 在考虑了 SOA中放大的自发辐射(ASE)噪声的基础上,计算了输入光功率、SOA抽运电流、环内光滤波器的带宽对Q值的影响. 数值计算的结果与实验现象基 关键词： 微波光子学滤波器 Q值')" href="#">Q值 半导体光放大器 放大的自发辐射     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Broadband, low intensity noise CW source for OCT at 1800 nm

We report on an all-fiber CW supercontinuum source, based on erbium amplified spontaneous emission (ASE) source pumping dispersion-shifted highly nonlinear step-index silica fiber. As low as −120 dBc/Hz intensity noise of the near-Gaussian >200 nm bandwidth radiation was recorded. The source can enable micron-scale optical coherence tomography around the low-scatter 1800 nm region.     

Gain clamped L-band EDFA with forward–backward pumping scheme using fiber Bragg grating

The paper proposes a novel two stage L-band erbium doped fiber amplifier with forward–backward pumping scheme for transmission of 32 wavelength division multiplexed (WDM) channels. It is gain clamped with an in-line fiber Bragg grating (FBG) to provide flat gain over 45 nm by restricting and reutilizing amplified spontaneous emission (ASE). We demonstrate that it provides an efficient small signal gain with minimum noise figure of over 20 dB and 5.5 dB, respectively, in the L-band region (1565–1610 nm) by comparing with its forward and backward pumped counterparts with fixed Er³⁺ fiber length of 20 m for −30 dBm/channel input power. We also obtain the gain and noise figure dependence as a function of each of the Er³⁺ fiber lengths, pump power (both 1480 and 980 nm), and temperature. Hence a 10 nm region (1580–1590 nm) has been acknowledged where temperature variations become constricted for 30 °C variations (15–45 °C).     

超宽带可调谐SOA四波混频波长变换器的实验研究

基于半导体光放大器(SOA)光纤环形激光器中的双泵浦四波混频效应,构成超宽带并且完全透明的波长变换器,成功实现1550nm窗口2.5Gb/s信号的可调谐波长变换,变换效率在50nm范围内保持基本平坦,同时测出了SOA增益和自发辐射(ASE)噪音功率的关系.实验结果表明,在一定限制条件下,提高泵浦功率可以提高变换信号的信噪比.     

Effect of amplified spontaneous emission on semiconductor optical amplifier based all-optical logic

The performances of all-optical logic gates XOR, AND, OR, NOR and NAND based on semiconductor optical amplifier (SOA) have been simulated including the effects of amplified spontaneous emission (ASE). For the parameters used, all-optical logic gates using SOA are capable of operating at speed of 80 Gb/s.     

Noise in optical amplifiers

This article presents an application of a recently published probablistic model for traveling wave optical amplification. Both optical signal and amplified spontaneous emission (ASE) noise are modeled as bunches of photons traveling along the amplifying region with size varying according to simple random rules. The results of the theory enable one to obtain a complete and accurate characterization of the signal and noise counting at the amplifier output. On the basis of the above statistics, we find a realistic evaluation of the limits imposed by both quantum and ASE noise on the performances of a receiver including an optical amplifier at a preamplifier stage.     

Impact of optical modulation formats on SPM-limited fiber transmission in 10 and 40 Gb/s optimum dispersion-managed lightwave systems

In this paper, 10 and 40 Gb/s optical systems have been investigated for nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed return-to-zero (CSRZ) and RZ-differential phase-shift-keying (RZ-DPSK) data formats. For the range of the optical signal power from −5 to 15 dBm, a maximum self-phase modulation (SPM)-limited transmission distance L_SPM is determined with eye-opening penalty (EOP) >1 dB .The observations are based on the modeling and numerical simulation of optimum dispersion-managed transmission link. Transmission over distances of the order of several hundreds of kilometers has been shown with and without amplified spontaneous emission (ASE) noise of the in-line erbium-doped fiber amplifiers (EDFAs).     

Experimental study of SOA-based NRZ-to-PRZ conversion and distortion elimination of amplified NRZ signal using spectral filtering

We experimentally study both reshaping of nonreturn-to-zero (NRZ) signal and NRZ to pseudoreturn-to-zero (PRZ) format conversion based on self-phase modulation of a semiconductor optical amplifier (SOA) and detuning an optical bandpass filter (OBF). When an OBF with 1 nm bandwidth is blue shifted by 0.8 nm, the distortion of the amplified NRZ signal at 10 Gbit/s is shown to be eliminated completely. When an OBF with 0.32 nm bandwidth is red shifted by 0.42 nm from the carrier frequency, NRZ-to-PRZ conversion at 10 Gbit/s is obtained. A holding beam is used to suppress the SOA noise and improve the output extinction ratio (ER). The output ER of both the reshaped NRZ and the converted PRZ is larger than 10 dB when the signal wavelength is longer than 1540 nm, and an input power dynamic range from −7 dBm to 2 dBm is obtained at a signal wavelength of 1563.6 nm. The average power of the reshaped NRZ signal is about 3 dBm at an input power dynamic range of 13 dB. The amplitude fluctuation of the converted PRZ signal is around 1.6 dB.     

有源光纤环脉冲复制器的噪声特性研究

借助半导体光放大器(Semiconductor optical amplifier,SOA)静态模型分析了有源光纤环脉冲复制器的输出放大自发辐射(Amplified spontaneous emission,ASE)噪声功率特性与环内SOA偏置电流及环内注入直流光功率之间的关系,并对环输出噪声分布的形态进行了仿真分析。用较少的实测数据点,使用插值方法对原有噪声曲线进行了快速重构。实验研究了其重构误差分布。     

Noise figure and gain temperature dependent of praseodymium-doped fiber amplifier by using rate equations

A theoretical study of the temperature dependent noise effects of praseodymium-doped fiber amplifiers (PEDFAs) has been examined. The Pr³⁺-doped ZBLAN fiber amplifier pumped at 1017 nm and Pr³⁺-doped GeGa-sulfied fiber amplifier pumped at 1028 nm are chosen. The temperature-dependent rate and propagation equation related to four-level system consideration which is based on the population difference among amplification levels has been used. The population difference depends on pump and signal powers, Boltzman factor K_B, cross-sections, noise figure (NF) and Pr³⁺ concentration. The numerical results obtained over the temperature range from −20 °C to + 60 °C are used to present an analytical expression for the signal gain and noise figure effects in PDFAs length and noise figure with input pump power. The amplified spontaneous emission (ASE) has been taken into account.     

Simulation of DWDM signals using optimum span scheme with cascaded optimized semiconductor optical amplifiers

We numerically simulated the ten channels at 10 Gb/s dense wavelength division multiplexing (DWDM) transmission faithfully over 17,227 km using 70 km span of single mode fiber (SMF) and dispersion compensating fiber (DCF) using optimum span scheme at channel spacing 20 GHz. For this purpose, inline optimized semiconductor optical amplifiers (SOAs) and DPSK format are used. We optimized the SOA parameters for inline amplifier with minimum crosstalk and amplified spontaneous emission noise with sufficient gain at bias current 400 mA. For this bias current, constant gain 36.5 dB is obtained up to saturation power 21.35 mW. We have also optimized the optical phase modulator bandwidth for 400 mA current which is around 5.5 GHz with crosstalk −14.2 dB between two channels at spacing 20 GHz.We show the 10×10 Gb/s transmission over 70 km distance with inline amplifier has good signal power received as compared to without amplifier, even at equal quality factor. We further investigated the optimum span scheme for 5670 km transmission distance for 10×10 Gb/s with channel spacing 20 at 5.5 GHz optical phase modulator bandwidth. As we increase the transmission distance up to 17,227 km, there is increase in power penalty with reasonable quality.The impact of optical power received and Q factor at 5670 and 17,227 km transmission distance for different span schemes for all channels has been illustrated. For launched optical power less than saturation, all channels are obtained at bit error rate floor of 10⁻¹⁰.     

A novel method degrading the combined effect of FWM and ASE noise in WDM systems containing in-line optical amplifiers

In this paper, a novel method degrading the combined effect of four-wave mixing (FWM) and amplified spontaneous emission (ASE) noise of the amplifier on the most heavily affected channel in an equally channel spaced wavelength division multiplexing (WDM) system containing in-line optical amplifiers is proposed. FWM effect is directly related to input powers of channels. So, FWM effect can be degraded by controlling channel input powers. In the proposed method, varying the input power of each channel in an optical fiber, the output optical signal to noise ratio (OSNR) values are evaluated and input powers of all channels are optimized in order to maximize the OSNR value of the channel having the lowest OSNR. To interpret the results obtained, output OSNR values for the minimum optical input power launched to the system by each channel are also computed. Being compared to the computed results for minimum optical input powers, the lowest output OSNR value among all channels for optimized input powers shows a 5.1867 dB increase in a 5-channel system, a 3.5988 dB increase in a 9-channel system, a 3.0855 dB increase in a 15-channel system and a 1.6795 dB increase for a 21-channel system. Furthermore, output OSNR values of all channels exhibit a significant increase.     

Improving channel capacity by nonlinearity compensation and noise suppression in high-speed multi-span optical transmission systems

In this paper, the channel capacity of 40 Gb/s multi-span nonlinear optical transmission systems with nonlinearity compensation and self-adapting Wiener filtering is studied by use of Finite State Machine (FSM) approach. The comparison of channel capacity of the system with differential phase shift keying (DPSK) and on–off keying (OOK) modulation is also investigated. The channel capacity increases monotonically with the input power for transmission systems with simultaneous compensation of dispersion and nonlinearity, which performs as well as linear system. DPSK shows a much better performance and the channel capacity has an improvement of at least 48 percent over that OOK modulation. A further reduction of the amplified spontaneous emission (ASE) noise accumulation is obtained by Wiener filtering, which improves the channel capacity considerably when the input peak power is less than 3 mW.     

Performance evaluation of path-averaged soliton pulses in loss-managed 10-Gbps soliton transmission link over a long haul

In this paper, the performance evaluation of path-averaged soliton transmission link for various performance measures viz. OSNR, optical power, extinction ratio, bit error rate (BER) and Q factor at different levels of noise figure and values of pulse width (FWHM) has been carried out. The performance of soliton transmission link is studied, taking into account soliton interaction, amplified spontaneous emission (ASE) noise and noise figure. The model presented considers interaction in a random sequence of solitons and the effect of the ASE noise added in each amplification stage. The influence of ASE noise, noise figure and pulse width with different amplifier spacing on the BER and quality factor has been investigated. It has been shown that these play dominant roles in degrading the performance measures. We have demonstrated the capability of path-averaged (guiding-centre) soliton for a long-haul distance of 17,000 km at a bit rate of 10 Gbps without ASE effect and noise figure in each amplifier span length of 500 km. The average value of quality factor is found to be 16.6 dB and the average BER is of the order of 10⁻¹² over the transmission distance of 17,000 km. Further, it has been investigated that a severe system penalty results on the inclusion of ASE effect and noise figure in order to achieve the same level of performance. Thus, the investigations ascertain that in order to maintain the same level of BER and Q factor, the amplifier spacing and total transmission distance reduce considerably.     

The temperature dependency of EDFAs in the 1480 nm pumping configuration

A theoretical study of the temperature-dependent gain and noise figure effects on erbium-doped fiber amplifiers (EDFAs) pumped at 1480 nm is investigated, solving the propagation equations related to two level systems. The solution of these equations is based on the population and temperature difference among amplification levels. The temperature-dependent propagation equation considered is used to determine the gain and noise figure effects on EDFAs. The population difference depends on pump and signal powers, Boltzmann factor K_B, cross-sections, noise figure (NF) and Er³⁺ concentration. The temperature-dependent gain and noise figure effect the EDFA length are numerically obtained for the temperature range of −20 °C to +60 °C. All of the analyses consist of the amplified spontaneous emission (ASE) effect.     

Analysis and minimization of cross phase modulation in semiconductor optical amplifiers for multichannel WDM optical communication systems

A theoretical model for crosstalk in multichannel wavelength division multiplexing communication systems due to cross phase saturation in semiconductor optical amplifier structure is developed. This theoretical model is used to analyze the impact of the cross phase noise on the performance of semiconductor optical amplifiers in saturation region for WDM communication system by using differential phase shift modulation format. It is shown that by increasing the carrier life time, width and thickness while reducing the confinement factor, differential gain and bias current in the SOA structure mitigates the cross talk due to cross phase saturation. The impact of penalty and cross phase noise imposed on multichannel WDM links have been investigated for different parameters of the SOA with the variation in transmission distance. With the slight increase in differential gain of 200.2 × 10⁻¹⁸ cm² and confinement factor 0.41, the maximum transmission distance observed is 5220 km with good quality and nil power penalty for 10 × 40 Gb/s soliton RZ-DPSK WDM signals for the first time.     

双向掺铒光纤放大器的特性分析

讨论了双向掺铒光纤放大器的结构方案,利用考虑放大的自发辐和北员耗影响的双向掺铒光纤放大器稳态放大速率方程模型分析的增益与掺铒光纤长度、输入信号光功率、帛运光功率及抽运方式等参数之间的关系,研究了单向和双向等功率抽运下正反向噪声系数随正反向信号光输入功率的变化行为。