Net lateral shift of reflected beam due to surface plasmon resonance in Kretschmann configuration

When surface plasmon resonance is excited in Kretschmann configuration, the maximum Goos–Hänchen shift occurs at the resonant angle which is associated with the minimum value of reflectivity, but the maximum angular shift occurs at two incident angles beside the resonant angle. When the reflected beam is detected at Rayleigh range, the maximum net lateral shift of the reflected beam does not encounter the resonant angle and its magnitude is lager than that of Goos–Hänchen shift. Numerical simulation shows that theory agrees well with numerical results when the beam width is large enough.     

Control of direction of Goos–Hänchen shift on reflection from a weakly absorbing medium

The Goos–Hänchen effect of reflected beams at the interface between isotropic medium and weakly absorbing medium was studied. We find that there is a lateral shift when a light beam travels through the interface for reflected beam for TM wave. The influence of permeability and permittivity on the Goos–Hänchen shift was discussed, respectively. When the weakly absorbing medium is right-handed material the imaginary of magnetic permeability will control the direction and magnitude of the shift. On the contrary, when the weakly absorbing medium is left-handed material, the refractive index of the isotropic medium determines the direction and magnitude of the shift.     

Giant positive and negative lateral shifts from the Kretschmann-Raether configuration with a weakly absorbing left-handed slab

The lateral shift of a TE-polarized beam reflected from the Kretschmann-Raether structure with a weakly absorbing left-handed slab is studied theoretically. It is shown that the lateral shift can be very large negative as well as positive near the resonant condition. These large negative and positive shifts can be one order of magnitude much larger than the shift from the corresponding nonabsorbing slab. As the absorption factor increases, the incident angle of producing largest lateral shift increases when the thickness is kept unchanged but the thickness of the slab of producing largest lateral shift decreases when the incident angle is kept unchanged.     

上海光源储存环主支撑减振研究

 上海光源是一台在建的第三代同步辐射光源,对束流轨道稳定性要求很高。由磁铁和支架组成的支撑组件的机械稳定性是影响束流轨道稳定性的重要因素。对主支撑组件样机的测试结果表明,其最低共振频率处放大倍数为50左右,超过要求5倍。因此,需要研究相应的减振措施。利用阻尼减振原理设计了一种约束阻尼结构。在样机上的测试结果表明,安装该装置后,支撑组件的共振放大倍数最大可以降低91.8%,对应的功率谱密度的峰值可以降低25 dB。因此,该装置可以用来增加支撑的稳定性。     

Physical origin of large positive and negative lateral optical beam shifts in prism-waveguide coupling system

Large lateral beam shift in prism-waveguide coupling system is theoretically analyzed from the viewpoint of interference between multiple reflected beam constituents. It is shown that the reflected beam is a result of interference between two beams: the beam directly reflected from the prism and the total leaky beam coming from guided mode. The thickness of coupling layer determines the amplitude of the total leaky beam, and further determines the sign (positive or negative) of the reflected beam shift. Because of interference between two beams, intrinsic damping itself plays an important role in deciding the distortion of the reflected beam.     

Simultaneously Large and Opposite Lateral Beam Shifts for TE and TM Modes on a Double Metal-Cladding Slab

We report simultaneously large and opposite Goos-Hanchen shifts for TE and TM beams on a double metalcladding slab. Theoretical examination shows that both positive and negative lateral shifts are in two orders of the wavelength. It is also found that the magnitude of the lateral beam shift strongly depends on the thickness of the upper metal layer. The optimal thickness of the upper metal layer for zero reflection is found to be the critical thickness above which a negative beam shift occurs. Numerical calculations are in good agreement with the theoretical results.     

束测误差对阻尼系统的影响

讨论了束测误差对阻尼系统工作状况的影响．结果表明，束测误差将减低阻尼效果，增大为达到一定的阻尼速度所需阻尼系统功率，并导致闭轨畸变．给出了计算有关效应的公式．     

包含辐射阻尼效应的束流纵向微波不稳定性研究

 包含束团辐射阻尼效应的Fokker-Planck方程是比较完备地描述粒子运动状态的束团分布方程。在Fokker-Planck方程的基础上采用微扰展开方法对纵向微波不稳定性的发生机制及过程进行了分析，并且根据计算结果，研究了辐射阻尼效应对纵向微波不稳定性的影响。在计算中包含了静态的势阱畸变效应。计算结果表明，包含辐射阻尼效应的纵向微波不稳定性阈值高于没有辐射阻尼效应的不稳定性阈值。     

Observation of large positive and negative lateral shifts of a reflected beam from symmetrical metal-cladding waveguides

Both large positive and negative lateral shifts were observed for the reflected light beam on a symmetrical metal-cladding waveguide. The positive and negative shifts approach about 480 and 180 microm, respectively, which to our knowledge are the largest experimental results ever reported. The experiment also proves that the positive or the negative shift depends on sign of the difference between the intrinsic and radiative damping.     

Positive and Negative Lateral Shifts from an Anisotropic Metamaterial Slab Backed by a Metal

The lateral shift of a light beam at the surface of an anisotropic metamaterial (AMM) slab backed by a metal is investigated. Analytical expressions of the lateral shifts are derived using the stationary-phase method, in the case that total reflection does and does not occur at the first interface. The sign of the lateral shift in two situations is discussed, and the necessary conditions for the lateral shift to be positive or negative are given. It is shown that the thickness and physical parameters of the AMM slab and the incident angle of the light beam strongly affect the properties of the lateral shift. Numerical results validate these conclusions. The lossy effect of the metamaterial on the lateral shift is also investigated.     

任意偏振态光束全反射时的侧向和横向位移

光束在电介质界面发生全反射时,实际反射光束会在入射面内相对于几何反射光束产生一侧向位移,在垂直于入射面的方向产生一横向位移。利用改进的能流法研究了任意偏振态光束发生全反射时的侧向和横向位移特性。研究表明,侧向位移的大小与入射光束的两组成部分———TE和TM偏振光的相位差无关,而与两组分的光强比密切相关,且该位移可以表示为TE和TM偏振光束各自的位移按光强的加权平均。横向位移的大小不仅与入射光束两组分的光强比相关,还与组分的相位差密切相关。另外,反射光束不仅在椭圆偏振态入射的情况下会产生横向位移,而且在TE和TM偏振态之外的其他线偏振态入射时,也会产生横向位移。     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency(RF)cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode(HOM)couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility)HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project(PEFP)in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

Lateral shifts of an optical beam in an anisotropic metamaterial slab

The lateral shift of a light beam at the surface of an anisotropic metamaterial slab is investigated. Analytical expressions of the lateral shifts are derived using the stationary-phase method, in the case that total reflection does and does not occur at the first interface. The sign of the lateral shift in two situations is discussed, and the necessary conditions for the lateral shift to be positive or negative are given. It is shown that the thickness and physical parameters of the anisotropic metamaterial slab, as well as the incident angle of the light beam, strongly affect the properties of the lateral shift, and numerical results validate these conclusions. The effect of a lossy metamaterial on the lateral shift is also investigated. A restriction on the thickness of the slab is obtained, which is necessary for the stationary-phase method to remain valid.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency (RF) cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode (HOM) couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility) HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project (PEFP) in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

基于胶合棱镜的AOTF成像光谱仪横向色差校正

设计声光可调谐滤波器(AOTF)成像光谱仪时,ZEMAX等软件缺乏AOTF光学表面,导致光学设计困难,本文根据波矢量匹配原理,在ZEMAX中建立了基于声光衍射效应的AOTF自定义表面模型,实验表明该模型能够实现AOTF的衍射光精确追迹。在此基础上,针对传统方法校正AOTF横向色差时残差较大的问题,提出了基于胶合棱镜的高精度横向色差校正方法,结合AOTF自定义表面,完成了胶合棱镜的玻璃组合和顶角的自动优化。结果表明,文章提出的自定义表面和胶合棱镜色差校正相结合的方法大大方便了AOTF成像光谱仪的设计,能够将横向色差控制到0.000 3°,比以往方法提高了一个量级,有效抑制了光谱图像的漂移。     

国际直线对撞机的参数选择

给出了确定直线对撞机参数的一般程序, 作为一个例子, 给出了超低束团电量时的参数表. 文章的主要目的是说明束流参数和对撞点以及阻尼环之间的相互制约关系. 对于17km的阻尼环, 它的能量被建议由5GeV升到7GeV. 然而,对于6km的阻尼环能量为5GeV是合理的.     

Analysis of the positive or negative lateral shift of the reflected beam in Otto configuration under grazing incidence

We investigate the lateral shift of a TM-polarized light beam reflected from Otto configuration under grazing incidence. It is found that the lateral shift is strongly dependent on the thickness of the air-gap layer. By employing the pole-null representation, we demonstrate that the lateral shift is closely related to the null of the reflection function. The numerical simulations for a Gaussian beam are performed to demonstrate the validity of our theoretical analysis.     

逐圈测量系统在合肥光源数字反馈调试中的应用

 使用逐圈测量系统作为观测手段,通过对逐圈测量系统采集所得数据进行分析,判断了数字反馈系统调试过程中的反馈效果。在改变六极铁电流以逐步改变储存环的色品值的过程中,通过逐圈测量系统观察了束流不稳定性,计算得到振荡增长时间和阻尼时间分别为0.258 ms和1.172 ms。并测量和计算了工作点、相空间等束流特性参数,分析了束流靠近和穿越5/9共振线的完整过程。     

Minimization of sound radiation from baffled beams through optimization of partial constrained layer damping treatment

An optimization study is presented with aim to minimize the sound power radiated by a simply supported, baffled beam with constrained layer damping (CLD) treatment. The governing equation of motion for the calculation of time-harmonic response of a partially CLD covered beam is derived first on the basis of energy approach. Assumed-modes method is used to solve the equation with obtained frequency response functions at different beam locations, which are further used for the calculation of its radiated sound power into half free-space by using Rayleigh’s integral. The optimization problem is then formulated to minimize the sound power radiated by the beam over a frequency range of interest covering multiple resonant modes. A genetic algorithm-based penalty function method is employed to search for the optimum of location/length of the CLD patch and the shear modulus of viscoelastic layer. Optimal results show that for a simply supported beam with a transverse force applied at its central location, it is not necessary to fully cover the structure using CLD patch in order to achieve the largest reduction in the sound power radiated by the beam over a frequency range. With inclusion of the amount of damping material to be minimized, the optimal CLD coverage length is only one-fourth of the base beam’s. Moreover, the optima of three design variables, the CLD coverage length, location on the beam and the shear modulus of viscoelastic layer, are highly relevant to each other.     

Vibration analysis of a beam with PCLD Patch

An analytical approach for vibration response analysis of a beam with single passive constrained layer damping (PCLD) patch is presented. The governing equation of motion of the beam is firstly derived on the basis of an energy approach and the Lagrange equation. The noval contribution is that a third admissible function is introduced to represent the longitudinal displacements of the constraining layer in the PCLD patch when the assumed-modes method is applied for discretizing the governing equation. In conventional analytical approaches, only two admissible functions are used together with a longitudinal static equilibrium equation of a section of base beam or constraining layer. Comparison of the computational results from the proposed analytical approach and the conventional analytical approach as well as a commercial FEM code reveals that the proposed analytical approach can describe the vibration responses of the damped beam more accurately for commonly used viscoelastic material (VEM) layer in the PCLD patch while the conventional analytical approach, in general, overestimates the damping effects of the PCLD patch. The advantages and disadvantages of the proposed analytical approach and conventional analytical approach are discussed through some case studies.