聚碳酸酯与苯乙烯-丙烯腈共聚物共混体系相容性及其对光学性能的影响

利用分子内链段排斥性相互作用理论研究了聚碳酸酯 (PC) 苯乙烯 丙烯腈共聚物 (SAN)共混体系中组份分子量及SAN共聚比例对体系相容性的影响规律 ,确定了获得均相的PC SAN共混体系的条件 ,考察了体系相容性与光学性能之间的关系 .通过实验获得了均相的PC SAN共混物 ;研究结果表明PC聚合度为 90、SAN聚合度为 3 0的PC SAN(S体积含量为 68%)体系共混比在 60∶40附近时体系的双折射能够实现补偿 ,紫外透光率达到 70 %.     

Styrene-methyl acrylate copolymers and acrylate homopolymers in solution

Molecular weight determinations by light scattering and osmometry and intrinsic viscosity measurements were made in various solvents on fractions of styrene–methyl acrylate copolymers with different compositions and on acrylate homopolymers prepared by free-radical reaction. Relations between intrinsic viscosity [η] and molecular weight M thus established are compared with those reported by other authors. 2-Methylcyclohexanol was found to be a theta solvent for the copolymers and both parent homopolymers, and isoamyl acetate was a theta solvent for poly(methyl acrylate). From theta point viscosity data obtained with these solvents, unperturbed chain dimensions were estimated. The results are compared with the unperturbed dimensions estimated from the [η]–M relations obtained in good solvents. On the basis of the experimental data it was found that the unperturbed dimension depends linearly on the copolymer composition, in contrast to the case of styrene–methyl methacrylate copolymers. Composition dependences of the theta temperature and of the parameter describing the long-range interactions between nonadjacent segments in polymer chains were investigated. The result implies that long-range interactions between monomeric units never disappear even when those between the same monomeric units vanish. The Huggins constant for copolymer is discussed in terms of the excluded volume variable.     

Alkyl chain branching in ethylene–vinyl acetate copolymer

Ethylene–vinyl acetate copolymers contain two kinds of side chains: acetoxy branches originating from incorporated vinyl acetate and alkyl branches. The alkyl branching was determined by infrared analysis after converting the ethylene–vinyl acetate copolymer to a hydrocarbon polymer by three steps: hydrolysis, iodation with hydriodic acid containing red phosphorus, and reductive hydrogenation with lithium aluminum hydride. It was found that physical properties such as stiffness were dependent both on the degree of alkyl chain branching and on vinyl acetate content.     

聚苯乙烯大分子单体与醋酸乙烯酯接枝共聚物的合成及表征

<正> 用大分子单体与小分子单体共聚是七十年代初才出现的合成接枝共聚物的一种新方法。通过共聚合反应而不是接枝反应同时形成主干及支链。这种接枝共聚物由于形成支链的大分子单体是预先合成的,其分子量分布较窄,又可调节控制,所以合成的接枝共聚物支链长短比较均一,副反应较少,链结构比较明确,因此也易于表征。     

Viscometric study of dilute solutions of polymer-polymer mixtures. Temperature and composition effects

Viscometric interaction parameters between pairs of homopolymers or an acidic and a basic copolymer in dioxane were determined by two procedures: (a) determination of the intrinsic viscosity of polymer (A) in dilute dioxane solutions of polymer (B) at 30°; (b) determination of the Huggins constants for 1:1 mixtures of polymers at 50°. The Δb₂₃ values obtained by these methods were different but positive and they increased from the most incompatible to the completely compatible system. Non-linear relations were found for the Huggins constant vs temperature and the intrinsic viscosity vs composition.     

Batch and semicontinuous emulsion copolymerization of vinyl acetat–butyl acrylate. I. Bulk,surface, and colloidal properties of copolymer latexes

Vinyl acetate (VAc)–butyl acrylate (BuA) comonomer mixtures with various composition were polymerized by batch and semicontinuous emulsion polymerization processes. PVAc and PBuA homopolymer latexes as well as the (VAc-BuA) copolymer latexes were characterized with respect to particle size, molecular weight, acid end groups on particle surfaces, and colloidal stability against electrolytes. The surface and colloidal properties of these latexes were also compared before and after aging and acid hydrolysis. The average particle size of batch latexes was independent of copolymer composition, whereas for semicontinuous latexes it decreased with increasing BuA content and was always lower than that of the corresponding batch latex. The molecular weight distribution (MWD) for batch latexes was narrower and much less dependent on composition than that of the semicontinuous latexes; bimodal MWD was found in most semicontinuous latexes with a substantial amount of low MW fraction. The total weak and strong acid end groups on particle surfaces for semicontinuous latexes is higher, and more dependent on composition, than the batch latexes. Acid-induced hydrolysis results in a drastic change in the type and concentration of the surface groups of the semicontinuous latex particles. Colloidal stability against electrolytes showed that both electrostatic (due to surface acid groups) and steric [due to surface poly(vinyl alcohol)] mechanisms are contributing. However, for semicontinuous latexes, increasing PVAc content above 50 mol % resulted in a proportional increase and ultimately dominant role of steric stabilization. The results were interpreted in terms of differences in reactivity ratios and water solubilities of the two monomers and their effects on the locus of initiation and growth in the two polymerization processes, as well as the monomer sequence within the polymer chain and degree of homogeniety of the copolymer composition within the particle.     

Effect of molecular weight and its distribution on the spinodal for polydisperse polymer solutions

The Flory–Huggins interaction parameter χ(r_i) is considered as dependent on the chain length of a polymer. Therefore, a modified free energy expression of Flory–Huggins theory is obtained for the polydisperse polymer solutions. Based on this modified free energy expression and the thermodynamics of Gibbs, the expression of spinodal for polydisperse polymer solutions is obtained. For a given χ(r_i) according to de Gennes, the spinodals are calculated for polydisperse polymer solutions at different molecular weights and their distributions. It is found that all the interested variables r_n, r_w, r_z and molecular weight distribution have an effect on the spinodal for polydisperse polymer solutions, where the effect of changing r_w is much greater than that of changing r_n, r_z and molecular weight distribution.     

乙烯-醋酸乙烯酯-乙烯醇三元共聚物性质的研究

以乙烯-醋酸乙烯酯共聚物(EVA)为原料,通过控制VA的水解程度制得一系列不同组成的乙烯-醋酸乙烯酯-乙烯醇三元共聚物.研究表明:随水解程度的增加共聚物的结晶性越来越好.在一定水解度范围内共聚物具有良好的综合力学性能,是一种新型的热塑性弹性体.     

A theoretical investigation of the production of branched copolymers in continuous stirred tank reactors

A comprehensive mathematical model for free-radical copolymerization reactions has been developed for a homogeneous continuous stirred tank reactor. The present model is based on a fairly general copolymerization scheme accounting for the formation of linear and branched copolymer chains. Both chain transfer to polymer and terminal double bond reactions are considered in order to predict the long chain branching frequency. Changes in molecular weight, composition and degree of branching occurring during the copolymerization reaction are modelled using the method of moments. To break-down the dependence of the moment equations on higher order moments two different closure methods are considered. The predictive capabilities of the model are examined in relation to the solution copolymerization of methyl methacrylate with vinyl acetate. It is shown that both chain transfer to polymer and terminal double bond reactions significantly contribute to the broadening of the molecular weight and degree of branching distributions. Furthermore, the terminal double bond reaction effects significantly the copolymer number-average molecular weight and the concentration of terminal double bonds.     

CATIONIC POLYMERIC SURFACTANTS

An influence of polyvinyl alcohol molecular weight and acetate groups, present in the macromolecule, on adsorption and electrochemical properties of the TiO₂–polymer solution interface was studied. Calculated thickness of adsorption layers of PVA, on the surface of the oxide, allowed assume that acetate groups may have meaningful influence on the polymer chain conformation at the interface. Structure of macromolecules at titania–polymer solution interface was compared with that of bulk of solution. Obtained data allow determine the changes of the size and shape of polymer coils in the system. The results of experiments let us conclude main factors, responsible for observed zeta potential and surface charge changes of TiO₂. It was proved that change of the ion structure of Stern layer, depends on molecular weight and number of acetate groups (degree of hydrolysis) of PVA macromolecule. Possible mechanism of zeta potential changes was proposed as a function of pH of the solution and molecular weight of the polymer.     

Analysis of copolymer surfaces by surface reactions and XPS

Summary The adsorption of polar groups at the polymer melt/mould interface is detected by chemical analysis. Vinyl alcohol groups and vinyl acetate groups (after hydrolysis) react with heptafluoro-butanoic acid chloride to attach a fluorine-containing molecular group to the surface. By measuring fluorine and other elements with XPS the surface composition is determined. On a gold substrate vinyl alcohol groups are adsorbed in a copolymer of vinyl chloride, vinyl acetate and vinyl alcohol. If a vinyl chloride-vinyl acetate copolymer is compression moulded against gold, the polymer surface energy is increased by adsorption of vinyl acetate groups. Subsequent relaxation, after removal of the substrate, leads to slow desorption of vinyl acetate groups. At the interface of the vinyl chloride-vinyl acetate copolymer with nickel or aluminium the polymer is oxidized.

---

Zusammenfassung Die Adsorption von polaren Gruppen an der Polymerschmelze/Substrat — Grenzfläche wird chemisch analysiert. Vinylalkohol- und Vinylazetatgruppen in Oberflächen von Copolymeren reagieren (nach Hydrolyse) mit Heptafluorbuttersäurechlorid. Mit XPS (X-ray-Photoelectron-Spectroscopy) messen wir die Fluormenge, um die Oberflächenzusammensetzung zu bestimmen. In PVC/Ac/Alc Copolymerem adsorbieren Vinylalkoholgruppen an ein Goldsubstrat. Die Zunahme der Oberflächenenergie von PVC/Ac durch Schmelzen auf einer Goldoberfläche und die spätere Relaxation, werden verursacht durch Adsorption und Desorption von Vinylazetateinheiten. Bei Gebrauch von Nickel oder Aluminium wird die Polymeroberfläche oxydiert.

---

---

With 3 tables     

Solubility and Flory Huggins parameters of SBES, poly(styrene-b-butene/ethylene-b-styrene) triblock copolymer, determined by intrinsic viscosity

Solubility parameter and Flory Huggins interaction parameter of a triblock SBES have been obtained from intrinsic viscosity measurements. The solubility of the block copolymer in all solvents (methyl-cyclohexane, cyclohexane, cyclopentane, toluene and benzene) was found good except in the case of n-hexane. The results obtained are similar to other found in literature for SBR and SBS rubbers, and indicate that cyclohexane and cyclopentane and methylcyclohexane are the most compatible solvents for this kind of polymer.     

孪尾疏水缔合三元共聚物的粘度行为:水解度的影响

以十二烷基硫酸钠(SDS)为表面活性剂,利用氧化还原体系、采用前加碱共聚-共水解的方法制备了孪尾疏水缔合水溶性三元共聚物聚(丙烯酰胺／丙烯酸钠／N,N-二己基丙烯酰胺)[P(AM/NaAA／DiC6AM)],研究了P(AM／NaAA／DiC6AM)稀溶液及亚浓溶液的性能。随理论水解度的增加,P(AM／NaAA／DiC6AM)水溶液的特性粘数[η]增加,Huggins常数KH减小。P(AM／NaAA／DiC6AM)水溶液的表现粘度随理论水解度的增加而增加,随温度、剪切速率的增加而降低,随剪切速率的增加开始时降低较快而后变化较小。P(AM／NaAA/DiC6AM)在盐溶液中随NaCl、CaCl2质量浓度的增加,出现盐增粘现象;理论水解度不同的P(AM／NaAA／DiC6AM)与SDS水溶液的表现粘度在wSDS=0．050～0．400g／L范围内随SDS质量浓度的变化差别不大。     

Cloud-Point Curve for the System Copoly(Ethylene-Vinyl Acetate) Plus Methyl Acetate. Measurement and Prediction by Continuous Thermodynamics

The cloud-point curve for the system copoly(ethylene-vinyl acetate) plus methyl acetate has been measured by a simple visual method. The critical point was determined by using the phase volume ratio method. The method of continuous thermodynamics was applied for thermodynamic treatment. The composition of the copolymer is described by a divariate distribution function assumed as a generalized Stockmayer distribution. The activity coefficients were obtained with the aid of the Huggins Chi -parameter concept assuming Chi to be a quadratic polynomial with respect to the weight-average chemical composition of the copolymer. The three model parameters were calculated from the critical point and the slope of the cloud-point curve at the critical point. The cloud-point curve and the shadow curve were predicted from these parameters. The cloud-point curve shows qualitative agreement with experimental data.     

Semicontinuous seeded emulsion copolymerization of vinyl acetate and methyl acrylate

The semicontinuous seeded emulsion copolymerization of vinyl acetate and methyl acrylate was investigated. The effect of type of process (starved process versus semi-starved process), type of feed (neat monomer addition versus monomer emulsion addition), amount of seed initially charged in the reactor, and feed rate on the time evolution of the overall conversion, copolymer composition, and polymer particle size was analyzed. It was found that, in the case of the starved process, both monomers, but mainly vinyl acetate, accumulated in the reactor. The preferential accumulation of vinyle acetate resulted in a drift of the copolymer composition. Both monomers accumulation and copolymer composition drift were reduced by increasing the amount of seed initially charged in the reactor and by decreasing the feed rate. For the semi-starved process, it was found that a vinyl aceatate rich copolymer was formed when a low methyl acrylate feed was used, whereas a methyl acrylate rich copolymer was obtained at high methyl acrylate feed rates. For both starved process and semi-starved process, the total number of polymer particles, after an initial increase, reached a plateau value which was the same in all of the experiments carried out. These results were analyzed by means of a mathematical model developed for this system.     

Atom transfer radical polymerization and copolymerization of isoprene catalyzed by copper bromide/2,2'-bipyridine

ATRP, as one of the most successful controlled/‘‘living' radical polymerization techniques, has been applied to a large variety of monomers including styrenes,(meth)acrylates,(meth)acrylamides,acrylonitrile, and vinyl acetate. However, ATRP of isoprene still remains a challenge due to poor solubility of copper catalysts in isoprene and low chain propagation rate constant of the monomer. In this work,Cu Br/2,2'-bipyridine was found to effectively mediate ATRP of isoprene at 100 °C, 130 °C, and 150 °C with ethyl 2-bromopropionate as an initiator. The polymerizations proceeded smoothly and reached 48.1%,53.3%, and 71.0% conversions, respectively, in 72 h, producing polyisoprenes with molecular weights close to theoretical values and relatively narrow distributions. A block copolymer of polystyrene-bpolyisoprene was prepared using Cu Br/2,2'-bipyridine as a catalyst and polystyrene as a macroinitiator.The ~1H NMR and ~(13)C NMR analysis of polyisoprene indicated that the polymer had 88.8% 1,4-addition structure and 63.9% of the polymer backbone units were in trans-configuration.     

强阴离子型丙烯酰胺共聚物P(AM-co-NaAMPS)的结构与性能

在水介质中实施了丙烯酰胺 (AM)与 2 丙烯酰胺基 2 甲基丙磺酸钠 (NaAMPS)的溶液共聚合 ,制备了组成系列变化的强阴离子型共聚物P(AM co NaAMPS) ;通过红外光谱法与元素分析法对共聚物的组成进行了表征 ;稀释外推粘度法测定了共聚物的特性粘数及Huggins常数 ;测定了共聚物纯水溶液及盐水溶液的表观粘度及高温下共聚物盐水溶液的粘度保持率 ;重点考察了共聚物的结构与组成对其各种性能的影响规律 .实验结果表明 ,在聚丙烯酰胺 (PAM)分子主链上引入NaAMPS链节后 ,磺酸根的强阴离子性与庞大侧基的位阻效应 ,赋于共聚物P(AM co NaAMPS)以优良的溶解、增稠、耐温与抗盐性能 ,且这些性能随共聚物的结构与组成的改变发生规律性的变化 .     

Effect of solute hydrophobicity on phase behaviour in solutions of thermoseparating polymers

 Two-phase systems consisting of a polymer rich phase and polymer depleted phase, where the polymer is either ethyl(hydroxy ethyl)cellulose (EHEC) or Ucon (a random copolymer of ethylene oxide and propylene oxide), have been studied. Both of these polymers can be separated from an aqueous solution by either temperature increase or addition of cosolutes. The polymers are thermoseparating and phase separate in water solutions at the cloud point temperature. Two types of EHEC have been studied: one with a cloud point at 60 °C and the other at 37 °C. The Ucon polymer used in this study has a cloud point at 50 °C. Ternary phase diagrams of polymer/water/cosolute systems have been investigated. When a strongly hydrophilic or hydrophobic cosolute is added to an EHEC- or Ucon–water solution, a phase separation occurs already at, or below, room temperature. As cosolutes, hydrophobic molecules like phenol, butyric and propionic acid, and hydrophilic molecules like glycine, ammonium acetate, sodium carboxylates (acetate to valerate), were studied. The polymer rich phase formed when mixing polymer, water and cosolute was strongly enriched or depleted with hydrophobic or hydrophilic cosolutes, respectively. The two phase region increased for propionic acid, butyric acid and phenol as a result of increased cosolute hydrophobicity. The opposite occurred in the series sodium acetate, sodium butyrate and sodium valerate. The effect of temperature on the phase behaviour has also been investigated. Model calculations based on Flory–Huggins theory of polymer solutions are presented, in form of a phase diagram, which semiquantitatively reproduce some experimental results. Received: 5 July 1996 Accepted: 4 November 1996     

Cellulose whiskers reinforced polyvinyl alcohol copolymers nanocomposites

Nanocomposite materials were prepared from copolymers of polyvinyl alcohol and polyvinyl acetate and a colloidal aqueous suspension of cellulose whiskers prepared from cotton linter. The degree of hydrolysis of the matrix was varied in order to vary the hydrophilic character of the polymer matrix and then the degree of interaction between the filler and the matrix. Nanocomposite films were conditioned at various moisture contents, and the dynamic mechanical and thermal properties were characterized using dynamic mechanical analysis and differential scanning calorimetry, respectively. Tensile tests were performed at room temperature to estimate mechanical properties of the films in the non linear range. All the results show that stronger filler/matrix interactions occur for fully hydrolyzed PVA compared to partially hydrolyzed samples. For moist samples, a water accumulation at the interface was evidenced. The reinforcing effect was found to be all the higher as the degree of hydrolysis of the matrix was high.     

Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.