Liquid chromatographic trace enrichment with on-line capillary gas chromatography for the determination of organic pollutants in aqueous samples

Trace enrichment for the GC analysis of a series of chlorinated pesticides and polychlorinated biphenyls (PCBs) in aqueous samples has been achieved through a simple on-line technique involving sorption on an LC micro-precolumn followed by direct elution into a gas chromatograph with hexane. A 5-m retention gap coupled to the capillary GC column served as the recipient of a relatively large sample volume (ca. 100 μl) introduced into the GC. Partially concurrent solvent evaporation during sample introduction allowed a large sample capacity. Recoveries of more than 95% were observed for the majority of the compounds studied. Using 1.0 ml aqueous samples, detection limits of less than 1 ppt were found. The applicability of the developed method was demonstrated for a river water sample.     

Determination of polychlorinated biphenyls in sediment by on-line narrow-bore column liquid chromatography/capillary gas chromatography

Narrow-bore column liquid chromatography coupled on-line with capillary gas chromatography (LC/GC) is used for the determination of polychlorinated biphenyls (PCBs) in sediment via a heart-cutting technique. This method is compared with a method in which two off-line column clean-up steps are used with subsequent analysis by capillary gas chromatography. For the LC/GC analysis the recovery of PCBs was 90–100%. For two sediment samples from the river Meuse the LC/GC and the other, more laborious method showed good agreement.     

Fast miniaturised sample preparation for the screening and comprehensive two-dimensional gas chromatographic determination of polychlorinated biphenyls in sludge

Polychlorinated biphenyls (PCBs) in sludge are usually extracted by a technique such as Soxhlet with subsequent fractionation prior to long GC runs using GC-ECD or GC-HRMS. In this study, the extraction of selected chlorinated biphenyls (CBs) from a spiked sludge sample by three rapid techniques, i.e. ultrasonic (USE), pressurised-liquid (PLE), and microwave-assisted (MAE) extraction using a domestic microwave, was studied, with subsequent direct GC-ECD, GC-MS, or GC x GC-microECD analysis of the extracts. The main goal was to select an appropriate, and miniaturised, extraction method after only a brief optimisation and demonstrate the power of GC x GC analysis of dirty extracts. For PLE similar CB recoveries were found when extracting with either n-hexane or n-hexane/acetone (1/1). For USE and MAE, n-hexane/acetone (1/1) was the preferred extraction solvent. USE gave the best recoveries (80-95%; except 130% for CB 105). The only clean-up needed prior to GC-MS or GC x GC-gECD analysis was the removal of sulphur-containing compounds. GC-ECD was not suitable for these dirty extracts. The lowest LODs for the CBs (20 fg or 0.1 ng/g sludge) were found when combining USE and GC x GC-microECD, because of the powerful extraction, high separation power and excellent detectability provided by this technique.     

Optimisation and comparison of microwave-assisted extraction and Soxhlet extraction for the determination of polychlorinated biphenyls in soil samples using an experimental design approach

Optimisation of microwave-assisted extraction (MAE) for the extraction of polychlorinated biphenyls (PCBs) from soil samples has been accomplished using an experimental design approach. Variables studied have been: percentage of acetone (v/v) in an acetone:n-hexane mixture, solvent volume, extraction time, microwave power and pressure inside the extraction vessel. Five samples of a certified soil (CRM 481) have been extracted under the optimum conditions of the developed method and the results have been compared to those obtained by Soxhlet extraction. Good recoveries (>95%) have been obtained for all the PCBs studied. All extracts have been analysed by gas chromatography/mass spectrometry (GC/MS) and an optimum determination method for the electron impact mass spectrometric (EIMS) has also been developed.     

Monitoring of Polychlorinated Biphenyls in Surface Water Using Liquid Extraction,GC/MS,and GC/ECD

Abstract

A rapid and reliable analytical method, at trace level concentration was developed and validated for monitoring polychlorinated biphenyls (PCBs) in Jordanian surface water. The method combines the advantage of liquid extraction together with gas chromatography‐mass spectrometry (GC/MS) and gas chromatography‐electron capture detector (GC/ECD). The performance of the method was evaluated by analyzing certified reference material (CRM) of the analytes and applied on real water samples collected from different sites in Jordan. A mixture of 60∶40 dichloromethan‐petroleum ether was chosen as a convenient binary solvent for liquid–liquid extraction. The GC conditions for GC/MS were optimized using He as a carrier gas, temperature programming, and chlorpropham as an internal standard (IS).

The conditions for GC/ECD were performed using N₂ gas and a temperature program from 160 to 280°C with different increasing rates. The method of GC/MS in the selective ion mode (SIM) gave linear relationships for all PCBs tested between 0.60–6.0 µg/l with R ²=0.9934 (n=7×18). Recoveries from spiked water samples ranged between 87.6 and 91.4%. The mean accuracy and precision obtained were 4.9% and 2.16%, respectively. The mean of detection limit was 0.14±0.04 µg/l. In GC/ECD, linear relationships for all PCBs examined over the range of 0.3–2.4 µg/l was verified as characterized by a linear regression equation and correlation coefficient, R ²=0.9915 (n=12). The average precision and accuracy were 4.86% and 5.21%, respectively. Analyses results clarified that none of the examined Jordanian water samples contained any of the searched for PCBs within the detection limit achieved.     

Enantiomeric separation of chiral polychlorinated biphenyls on beta-cyclodextrin capillary columns by means of heart-cut multidimensional gas chromatography and comprehensive two-dimensional gas chromatography. Application to food samples

Three commercially available chiral capillary columns, Chirasil-Dex, BGB-176SE, and BGB-172, have been evaluated for the separation into enantiomers of the 19 chiral polychlorinated biphenyls (PCB) congeners stable at room temperature. The enantiomers of 15 chiral PCBs were, at least to some extent, separated using these beta-cyclodextrin based columns. Multidimensional techniques, such as heart-cut multi-dimensional gas chromatography (heart-cut MDGC) and comprehensive two-dimensional gas chromatography (GC x GC), were investigated for their ability to solve coelution problems with other PCBs present in commercial mixtures and real-life samples. Heart-cut MDGC improved the separation as compared to one-dimensional GC, and enantiomeric fractions of the investigated chiral PCBs could be determined free from interferences. However, limitations on the number of target compounds that can be transferred to the second column in a single run and, therefore, the time consumption, have led to the evaluation of GC x GC as an alternative for this type of analysis. With GC x GC, two column set-ups were tested, both having a chiral column as first-dimension column, and two different polar stationary phase columns in the second dimension. On using both column combinations, congeners 84, 91, 95, 132, 135, 136, 149, 174, and 176 could be determined free from coelutions with other PCBs. Results on the application of heart-cut MDGC to food samples such as milk and cheese are given, as well as the first results on the application of GC x GC to this type of samples.     

Gas chromatography/mass spectrometry of polychlorinated biphenyls using atmospheric pressure chemical ionization and atmospheric pressure photoionization microchips

Gas chromatography (GC) and ion trap mass spectrometry (MS) were combined with microchip atmospheric pressure chemical ionization (microAPCI) and microchip atmospheric pressure photoionization (microAPPI) sources. Selected polychlorinated biphenyls (PCBs, IUPAC Nos. 28, 52, 101, 118, 138, 153 and 180) were analyzed by GC/microAPCI-MS and GC/microAPPI-MS to demonstrate the applicability of the miniaturized ion sources in negative ion mode analysis. The microAPCI and microAPPI methods were evaluated in respect of detection limit, linearity and repeatability. The detection limits for the PCB congeners were somewhat lower with microAPCI than with microAPPI, whereas microAPPI showed slightly wider linear range and better repeatability. With both methods, the best results were obtained for highly chlorinated or non-ortho-chlorinated PCBs, which possess the highest electron affinities. Finally, the suitability of the GC/microAPPI-MS method for the analysis of PCBs in environmental samples was demonstrated by analyzing soil extracts, and by comparing the results with those obtained by gas chromatography with electron capture detection (GC/ECD).     

Vaporising systems for large volume injection or on-line transfer into gas chromatography: Classification, critical remarks and suggestions

Techniques for large volume introduction of liquid samples into capillary gas chromatography (GC) follow a small number of principals. Vaporising systems, vapour discharge modes and methods for solvent-solute separation are classified and evaluated.

Presently, programmed temperature vaporising (PTV) solvent split injection is the preferred method if on-column techniques cannot be applied. Critical re-evaluation suggests, however, that solvent evaporation and solvent-solute separation should be performed in separate compartments and optimized individually. Permanently hot chambers offer the highest capacity for solvent evaporation. The preferred techniques for solvent-solute separation are stationary phase focusing in a coated capillary or solvent trapping in an uncoated capillary precolumn. The vaporising chamber-precolumn solvent split-gas discharge system is proposed for large volume injection and on-line transfer of water-containing solvent mixtures, and in-line vaporiser-precolumn solvent split-overflow system for most on-line transfer applications.     

土壤与沉积物样品中多氯联苯总量的气相色谱-质谱法快速分析

建立了土壤和沉积物样品中多氯联苯总量的快速分析方法.样品经加速溶剂萃取,Bond ElutPCB SPE小柱净化后,采用气相色谱-质谱测定多氯联苯的总量,方法的平均回收率为84% ～106%,相对标准偏差为4.2% ～8.4%,多氯联苯总量的方法检出限为2.25 ng/g.该方法快速、灵敏、准确,适用于大部分土壤及沉积物样品中多氯联苯总量的快速筛查分析.     

非等间隔PCBs保留指数体系在光解行为研究中的应用

利用Ｃｈｕ等已建立的多氯联苯（ＰＣＢｓ）非等间隔保留指数体系,由文献中的相对保留时间计算出全部２０９种ＰＣＢｓ同类物（Ｃｏｎｇｅｎｅｒ）的保留指数（ＩＰＣＢ）。利用ＩＰＣＢ结合ＧＣ－ＭＳ对ＰＣＢ８７、ＰＣＢ１３８和ＰＣＢ１６９三种同类物的光解产物进行了定性分析,发现其光解产物主要为低氯代联苯。实验结果证明,非等间隔保留指数体系ＩＰＣＢ在ＰＣＢｓ同类物的定性分析中具有准确、实用、快捷、方便等优点。     

An Improved Method for Determination of Polychlorinated Biphenyls and Polybrominated Diphenyl Ethers in Sediment by Ultrasonic Solvent Extraction Followed by Stir Bar Sorptive Extraction Coupled to TD–GC–MS

An improved simple, fast and miniaturized method for the determination of polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in freshwater sediment using ultrasonic solvent extraction followed by stir bar sorptive extraction–thermal desorption–gas chromatography–mass spectrometry (USE-SBSE/TD–GC–MS) is presented. The sediment sample (0.2 g) is extracted with methanol (1:1.2, 2:1.0 mL) in an ultrasonic bath (two 5-min extraction cycles). The combined extracts are made up to 5 mL with water, and from the resulting solution, the analytes are preconcentrated on a stir bar coated with polydimethylsiloxane during 1 h of stirring. The loaded sorptive stir bar is then thermally desorbed and online analysed by GC–MS. For the analytes in river sediment, a linear dynamic range of 0.5–50 ng g^?1 was established and limits of detection in sub nanogram-per-gram level were achieved. Recoveries and repeatability were obtained in the ranges 62.8–91.5 % and 3.6–15.0 %, respectively. The method accuracy was confirmed by the analysis of PCBs and PBDEs in a certified reference material. The main improvement in comparison with similar published methods is in shortening the sample handling time and the method miniaturization.     

Sensitive GC/MS determination of 15 isomers of chlorobenzoic acids in accelerated solvent extracts of soils historically contaminated with PCBs and validation of the entire method

Chlorobenzoic acids (CBAs) are the major metabolite of aerobic bacterial degradation of polychlorinated biphenyls (PCBs). A rapid and simple simultaneous derivatisation method has been developed for gas chromatography-mass spectrometry determination in historically PCB-contaminated soils for 15 isomers of mono-, di-, tri-, tetra-, and pentachlorobenzoic acids in CBA mixtures. Two derivatisation agents (diazomethane and methyl chloroformate) and various conditions were evaluated (temperature, time, solvents, catalysts) in terms of efficiency. The optimised derivatisation method with diazomethane and 1% methanol running 1 hour at 5°C was used for derivatisation of extracts of soils and river sediment from historically PCB-contaminated sites; the extracts were prepared using accelerated solvent extraction by a previously described method. Methylated CBAs were separated by gas chromatography using a system with two different common columns, DB-5 and DB-200, in series-coupled (tandem) arrangement and detected by EI-MS. A clean-up with a gel permeation chromatography was carried out to remove soil interfering matrix compounds as well as major portion of PCBs. The limits of quantification ranged between 1 and 10 ng g^?1 of individual CBA in the soil. The procedure was applied to various soil samples from Lhenice (Czech Republic) highly contaminated with PCBs. CBAs were found in all tested soils and also in the river sediment. The most contaminated soil contained all CBAs representatives under the study with a total concentration of 3.1 µg g^?1 of dry soil.     

Developments in the use of chromatographic techniques in marine laboratories for the determination of halogenated contaminants and polycyclic aromatic hydrocarbons

Chromatography has been an important tool in marine laboratories. Since the 1960s, marine laboratories have been involved in the analysis of polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), and brominated flame retardants (BFRs). Column chromatography and liquid chromatography (LC) techniques have been used, mainly in the clean-up phase, while gas chromatography (GC) has been used extensively in the final determination of these contaminants. Developments have been observed from the use of packed GC columns, via capillary columns to the use of heart-cut multi-dimensional GC and comprehensive multi-dimensional GC. The progress made in interlaboratory studies and the availability of certified reference materials are discussed.     

Behavior of heavy solutes on a precolumn in on-column gas chromatography

The behavior of heavy solutes present in a sample injected on the precolumn has not been clarified in on-column injection onto gas chromatograph having a capillary column coupled to an uncoated precolumn in an oven. To investigate this point, an on-column gas chromatograph has been developed which is constructed with a heatable precolumn outside the oven. Some experiments were carried out in order to evaluate the performance. As a result, it was found that heavy solutes reach the first part of the main capillary column after the solvent has gone, resulting in sharp peaks without solvent effects. The reason why sharp peaks appear for the heavy solutes is also discussed. The cold-trapping effect has been shown to play an important role in narrowing the band width of the heavy solutes. Some of the advantages of the gas chromatograph developed are also presented.     

Dispersive liquid-liquid microextraction and gas chromatography-mass spectrometry determination of polychlorinated biphenyls and polybrominated diphenyl ethers in milk

An effective multi‐residue pretreatment technique, solid‐phase extraction (SPE) combined with dispersive liquid–liquid microextraction (DLLME), was proposed for the trace analysis of 14 polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in milk samples using gas chromatography–mass spectrometry (GC‐MS). Interesting analytes in milk samples were extracted with hexane after protein precipitation. The hexane extracts were loaded on an LC‐Florisil column to isolate analytes from the milk matrix. The elutes were dried and dissolved in acetone, which was used as the disperser solvent in subsequent DLLME procedures. The effects of several important parameters on the extraction efficiency were evaluated. Under the optimized conditions, a linear relationship was obtained in the range of 0.02–10.00 μg/L (PCBs) and 0.5–100.00 μg/L (PBDEs). The LOD (S/N=3) and relative standard deviations (RSDs, n=5) for all analytes were 0.01–0.4 μg/L and 0.6–8.5%, respectively. The recoveries of the standards added to raw bovine milk samples were 74.0–131.8%, and the repeatabilities of the analysis results were 1.12–17.41%. This method has been successfully applied to estimating PCBs and PBDEs in milk samples.     

Trace-level analysis of polychlorinated biphenyls,organochlorine pesticides and polycyclic aromatic hydrocarbons in human plasma or serum by dispersive liquid–liquid microextraction and gas chromatography–tandem mass spectrometry

A method to determine 8 polychlorinated biphenyls (PCBs), 23 organochlorine pesticides (OCPs) and 16 polycyclic aromatic hydrocarbons (PAHs) was described using dispersive liquid–liquid microextraction (DLLME) of a small amount of plasma or serum sample and gas chromatography–tandem mass spectrometry (GC–MS/MS). The appropriate selection of the extraction solvent and dispersing solvent contributes to a high extraction yield and a clean extract. To verify the developed method, the interference, linearity of the calibration curve, detection limit, precision and accuracy were evaluated. The calibration curves were linear by 2–3 orders of magnitude with correlation coefficients above 0.997 in all cases. The LODs of PCBs, OCPs and PAHs were measured in the ranges of 0.0006–0.0029, 0.001–0.029 and 0.0002–0.012 ng/mL. The intraday precision achieved by this method was 2.19–10.3% (PCBs), 1.65–14.3% (OCPs) and 0.91–12.8% (PAHs), and the intraday accuracy 1.56–7.37% (PCBs), 2.34–19.6% (OCPs) and 1.49–15.7% (PAHs). The advantage of this method is that the analysis of PCBs, OCPs, and PAHs can be performed in a single chromatographic run, and the low detection limit enables monitoring of target substances in low exposure general public samples, and the analysis procedure is relatively simple and fast.     

Evaluation of automated direct sample introduction with comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for the screening analysis of dioxins in fish oil

An automated direct sample introduction technique coupled to comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (DSI-GC x GC/TOF-MS) was applied for the development of a relatively fast and easy analytical screening method for 17 polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and 4 non-ortho polychlorinated biphenyls (PCBs) in fish oil. Comparison of instrumental performance between DSI-GC x GC/TOF-MS and the traditional gas chromatographic high resolution mass spectrometric (GC-HRMS) method showed good agreement of results for standard solutions analyzed in blind fashion. Relatively high tolerance of the DSI technique for lipids in the final extracts enabled a streamlined sample preparation procedure that only required gel permeation chromatography (GPC) and solid-phase extraction (SPE) cleanup with graphitized carbon black. The sample size for the method was 2g of cod liver oil, which achieved limits of quantitation (LOQs) of 0.019-7.8 pg/g toxic equivalent quotients for the individual PCDD/Fs. Lower detection limits can be achieved by using larger sample size and scaling up the sample preparation procedure, but this adds to the labor, time, solvent consumption, and expense of the approach. However, the streamlined method yielded 0.94 pg/g and 2.3 pg/g LOQs for 2,3,7,8-tetrachloro dibenzofuran (TCDF) and 3,3',4,4',5-pentachloro biphenyl (CB126), which were sufficiently low for regulatory monitoring of 2g samples. Therefore, instead of congener specific analysis, this streamlined analytical screening method for TCDF and CB126 has the potential to monitor fish oil contaminated with dioxin and dioxin-like PCBs at or above current food safety limits. Acceptable recoveries for nearly all analytes at three different spiking levels in fish oil samples were achieved with good repeatability.     

Multiresidue determination of persistent organochlorine and organophosphorus compounds in whale tissues using automated liquid chromatographic clean up and gas chromatographic-mass spectrometric detection.

A multiresidue method based on normal-phase LC for the sample clean up of whale tissues extracts prior to GC-MS determination of residues of polychlorinated biphenyls, organochlorine pesticides and derivatives and lipophylic organophosphorus pesticides has been developed. Pesticides were extracted from blubber by fusing and dissolving the fat in n-hexane and from liver and kidney by reflux in n-hexane. Hexanic extracts were directly injected on the silicagel column of the automated LC clean up system, using n-hexane as mobile phase. Diode array detection allowed the on-line monitoring of lipids elution from the LC system. Purified extracts were analysed by GC using mass selective detection. The developed procedure was applied to different tissues from a whale specimen appeared in the Valencian coast, finding high concentrations of OCs (up to 7.3 micrograms g-1 pp'-DDE, and 7.2 micrograms g-1 PCBs). The method was validated by means of recovery tests for all the compounds detected in the whale and also for some other OCs and OPs studied in this paper. The method improves other current methods for the analysis of persistent organochlorines in marine mammals with regard to time of analysis, solvent expend and automation; solvent exchanges are not necessary before GC analysis, and it allows the simultaneous determination of organophosphorus pesticides.     

双重净化-气相色谱法测定植物油中指示性多氯联苯

为了考察食用油中7种指示性多氯联苯(PCBs)的残留情况,建立了食用油中痕量多氯联苯测定的双重净化-气相色谱法。以乙腈提取样品,提取液浓缩至干后用正己烷溶解,经浓硫酸、硅胶分散固相萃取双重净化后进行气相色谱分析,外标法定量。优化的色谱条件为:HP-5石英毛细管柱(30 m×0.32 mm×0.25 μm)程序升温分离,流速0.8 mL/min,进样量1.00 μL,电子捕获检测器检测。结果表明:在优化的条件下,7种多氯联苯在10~500 μg/L范围内线性良好,相关系数大于0.999,不同基质中的检出限(S/N=3)范围为1.8~8.9 μg/kg,定量限(S/N=10)范围为5.9~29.8 μg/kg。在橄榄油、花生油和棕榈油空白样品中添加10、20、100 μg/kg 3个水平的7种多氯联苯,其加标回收率范围为71.0%~105.5%,相对标准偏差(RSD)范围为4.0%~11.3%。该方法具有操作简便、快速、准确的特点,可用于植物油中指示性多氯联苯残留量的日常检测。     

Analysis of dust and surface swab samples for octachlorodibenzo-p-dioxin and heptachlorodibenzo-p-dioxins by fused silica capillary GC with EC detection

A method is described for the analysis of contaminated building dust samples and surface swab samples for octachlorodibenzo-p-dioxin (OCDD) and heptachlorodibenzo-p-dioxins (HpCDDs). The samples were analyzed by fused silica capillary GC combined with electron capture detection. Analysis was preceded by a short HPLC cleanup step designed to remove polychlorinated biphenyls (PCBs) and other compounds that might interfere. The method was found to work successfully on surface swab and dust samples known to contain PCBs, OCDD, and HpCDDs. The overall recovery of the analysis procedure for OCDD was found to be approximately 80%. The detection limit for the method was sample dependent, but for one typical set of surface swab samples was 0.2 μg/m² of OCDD.