Dielectric relaxations in the liquid and glassy states of 47% polypropylene oxide in toluene as diluent

Molecular relaxations in 47-wt % polypropylene oxide of molecular weight 4000 in toluene as diluent have been studied by dielectric permittivity and loss measurements from 77 to 320 K, in the frequency range 1 Hz to 2 × 10⁵ Hz. One relaxation process (β process) is observed in the glassy state below T_g (= 148 K), and two processes are observed in the supercooled liquid at T > T_g. Relative to the amplitude of the fast relaxation process (i.e., the local segmental motions of the polymer chain), the amplitude of the slow process is increased and that of the β process decreased on dilution of the pure polymer. The β process has an Arrhenius energy of 17 kJ mol^?1. The rates of the two relaxations at T > T_g follow the Vogel–Fulcher–Tamman equation and seem to merge on cooling the liquid towards T_g. The relative temperatures at which the three relaxation processes occur at the rate of 1 kHz remain largely unaffected on dilution. The increase in static permittivity of the solution on cooling is more than anticipated from the temperature effects alone. It is suggested that the increase is due to the enhanced short-range orientational correlation of the dipoles, which may involve H bonding.     

The glass transition in linear low density polyethylene determined by thermally stimulated depolarization currents

New thermally stimulated depolarization currents (TSDC) results on LLD polyethylene functionalized with diethylmaleate polar groups are precisely computer fitted with the direct signal analysis technique. It is shown that the TSDC spectrum consists, with increasing temperatures, of a sub-γ peak, a sharp γ peak, and a β and an α relaxation. The first peak is analyzed in terms of Arrhenius relaxation times, whereas the γ and β transitions could only be fitted by using Vogel-Fulcher temperature dependence for the relaxation times. The best value for T_o obtained from both fittings is 69.7 K. This is a quantitative proof for the identification of the γ transition as one of the dielectric manifestations of the glass-rubber transition for polyethylenes, T_g = 136.5 K, which has been discussed extensively in the literature. The β relaxation, T_gβ = 237 K, has also the expected characteristic of a glass transition; the existence of two T_gs in polyethylene could explain our results. © 1996 John Wiley & Sons, Inc.     

Dielectric studies of the effects of thermal history on secondary relaxation in bisphenol-a-polycarbonate

The dielectric permittivity and loss of Bisphenol-A-polycarbonate (PC) was measured over the frequency range 100 Hz to 200 kHz and temperature range 77–383 K. One sub-T_g relaxation peak is observed which rapidly broadens with a decrease in temperature. This is attributed to a progressive separation of the γ and β peaks, which at high temperatures are merged to form one peak of high strength. The strength of the sub-T_g relaxations decreases on physical aging of PC but is increased if the sample is quenched from a temperature above its T_g. Slowly cooled PC has a lower strength of its sub-T_g relaxation than a quenched specimen. The thermal history of PC affects the magnitude of its sub-T_g relaxation.     

Relaxations of thermosets. III. Sub-Tg dielectric relaxations of bisphenol-A–based epoxide cured with different cross-linking agents

The sub-T_g relaxations of bisphenol-A–based thermosets cured with diaminodiphenyl methane and diaminodiphenyl sulfone have been studied by dielectric measurements over the frequency range 12 Hz to 200 kHz from their ungelled or “least” cured states to their fully cured states. Both thermosets show two relaxation processes, γ and β, as the temperature is increased toward their T_gs. In the ungelled states, the γ process is more prominent than the β process. As curing proceeds, the strength of the γ process decreases and reaches a limiting value, while that of the β process initially increases, reaches a maximum value, and then decreases. An increase in the chain iength and the number of crosslinks increases the number of -OH dipoles and/or degree of their motions in local regions of the network matrix. This is partly caused by the decreasing efficiency of segmental packing as the curing proceeds. The sub-T_g relaxations become increasingly more, separated from the α relaxation during curing. Physical aging causes a decrease in the strength of the β relaxation of the thermosets as a result of the collapse of loosely packed regions of low cross-linking density, and this decrease competes against an increase caused by further crosslinking during the “post-cure” process.     

Molecular relaxation in the blends of polystyrene/poly(2,6-dimethyl-1,4-phenylene oxide) at low temperature

Molecular relaxation behavior in terms of the α, β, and γ transitions of miscible PS/PPO blends has been studied by means of DMTA and preliminary work has been carried out using DSC. From DSC and DMTA (by tan δ), the observed α relaxation (T_α or T_g) of PS, PPO, and the blends, which are intermediate between the constituents, are in good agreement with earlier reports by others. In addition, the β transition (T_β) of PS at 0.03 Hz and 1 Hz is observed at −30 and 20°C, respectively, while the γ relaxation (T_γ) is not observed at either frequency. The T_β of PPO is 30°C at 0.03 Hz and is not observed at 1 Hz, while the T_γ is −85°C at 0.03 Hz and −70°C at 1 Hz. On the other hand, blend composition-independent β or γ relaxation observed in the blends may be a consequence of the absence of intra- or intermolecular interaction between the constituents at low temperature. Thus it is suggested that at low temperature, the β relaxation of PS be influenced solely by the local motion of the phenylene ring, and that the β or γ relaxation of PPO be predominated by the local cooperative motions of several monomer units or the rotational motion of the methyl group in PPO. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1981–1986, 1998     

Dielectric relaxation phenomena in a series of polyhydroxyether copolymers of bisphenol-A—endcapped polyethylene glycol with epichlorohydrin

Dielectric relaxation spectra of a series of polyhydroxyether copolymers have been obtained. It has been shown that the systems exhibit very similar relaxation spectra with the α(T_g) process a function of molecular weight. All systems exhibit two secondary relaxations: β (ca. 240 K) and γ (ca. 180 K). These have been assigned as hydroxyl motion and main-chain motion, respectively. The peak positions are not functions of composition in the ranges studied. The effect of sorbed water on the relaxation spectra is discussed.     

Properties of polyethylene modified with phosphonate side groups. II. Dynamic mechanical behavior

The viscoelastic behavior of phosphonate derivatives of phosphonylated low-density polyethylene (LDPE) was studied by dynamic mechanical techniques. The polymers investigated contained from 0.2 to 9.1 phosphonate groups per 100 carbon atoms and included the dimethyl phosphonate derivative and two derivatives for which the phosphonate ester group was an oligomer of poly(ethylene oxide) (PEO). The temperature dependences of the storage and loss moduli of the dimethyl phosphonate derivatives were qualitatively similar to those of LDPE. At low phosphonate concentrations, the α, β, and γ dispersion regions characteristic of PE were observed, while at concentrations greater than 0.5 pendent groups per 100 carbons atoms, only the β and α relaxations could be discerned. At low degrees of substitution, the temperature of the β relaxation T_β decreased from that of PE, but above a degree of substitution of 0.1, T_β increased. This behavior was attributed to the competing influences of steric effects which tend to decrease T_β and dipolar interactions between the phosphonate groups which increase T_β. For the phosphonate containing PEO, a new dispersion region designated as the β′ relaxation was observed as a low-temperature shoulder of the β relaxation. The temperature of the β′ loss was consistent with T_g(U) of the PEO oligomers as determined by differential scanning calorimetry, and it is suggested that the β′-loss process results from the relaxation of PEO domains which constitute a discrete phase within the PE matrix.     

Nuclear relaxation in atactic polystyrenes: T1 and T1ρ measurements

Measurements have been made on a series of linear atactic polystyrenes whose molecular weights range from 900 to 1.8 × 10⁶, where M _w/M _n ? 1.2. Spin lattice relaxation times have been measured in the laboratory frame (T₁) and in the rotating frame (T_1ρ) in the temperature range 90–500°K. Two major relaxation minima were observed in both sets of measurements. The high temperature process corresponds to the glass transition (α process), the position of the minimum depending on the chain length. The low temperature process appears to originate from the n-butyl endgroups in the polymer, its position being independent of chain length while its intensity is inversely proportional to molecular weight. No other minima were observed, in contrast to some other observations made by broadline and pulsed NMR techniques. Relaxation was exponential in all cases except in the region of the high temperature T_1ρ minimum and above. This nonexponential behavior is possibly connected with the transition at T > T_g observed by a number of other techniques and which is thought to correspond to a transition between two types of liquid state. A correlation frequency diagram has been drawn for all the processes observed in polystyrene by other techniques, (α, β, αβ, γ, and δ) which shows that the T₁ and T_1ρ minimum positions correlate well with the α process and that there is a possible contribution to the relaxation due to the γ process on the low temperature side of the α process. At these measurement frequencies the α and β processes are merged into an αβ process. There is no evidence for a contribution from the mechanical δ process. The effect of the endgroups is observed to very high molecular weights (4.98 × 10⁵), and it seems that a three-dimensional diffusion model would be more adequate than the one-dimensional model used to interpret similar behavior of paraffins and polyethylenes. Measurements of T₁ in the low-temperature region would constitute a method for a rough measurement of the molecular weight of these polymers.     

Dielectric properties of complex zn(II) salts of ethylene-methacrylic acid copolymer with n-hexylamine

This article describes dielectric properties of complex Zn(II) salts of ethylene-methacrylic acid copolymer (5.4 mol% methacrylic acid) with n-hexylamine. In all samples, the β′ relaxation near 340 K and γ relaxation near 170 K are observed. These are assigned, respectively, to micro-Brownian molecular motion of long segments above T_g and to local molecular motion of short segments below T_g. The dielectric results indicate that ionic clusters are not formed in these systems.     

Influence of microstructure and semi-crystalline morphology on the β and γ mechanical relaxations of the metallocene isotactic polypropylene

In this work, the characteristics of the β and γ mechanical relaxations, i.e., temperature and relative intensity, of a series of metallocene iPP samples (MPP) are analysed. The hypothesis that the temperature and the intensity of the glass transition (β relaxation) and local sub-T_g motions (γ relaxation) are related mainly to chain parameters and morphology has been corroborated. On the one hand, it has been found a critical average isotactic length (n₁) around 30 propylene units, under which the β and γ dynamics are promoted with respect to the α relaxation. On the other hand, it is apparent that the features which determine the degree of constraint within the inter-lamellar region, i.e., the fraction of low-T_m crystals, drive the relative intensities of the α, β and γ relaxation processes.     

Effects of diluent on molecular motion and glass transitions in polymers. III. The system poly(vinyl acetate)–toluene

Dielectric measurements, differential thermal analyses (DTA), and broad-line proton magnetic resonance (NMR) measurements are reported on the system poly(vinyl acetate)–toluene. Four dielectric relaxations were observed between 80 and 400°K. From proton NMR measurements on solutions in toluene and in deuterated toluene, the relaxation processes can be assigned, respectively, to segmental motion of poly(vinyl acetate), α; motion of side group, β′ rotation of toluene, β; local motions of poly(vinyl acetate) and toluene, γ, in order of appearance with decreasing temperature. Two stepwise changes in DTA traces have been observed and can be assigned as glass transition points T_gI and T_gII. Comparison of these glass transition points with temperatures at which dielectric relaxation times for the α and β processes are 100 sec, indicate that segmental motion of poly(vinyl acetate) and rotation of toluene are frozen-in at T_gI and T_gII, respectively. Activation plots for the α process conform to the Vogel–Tamman equation. In terms of the parameters A, B, and T₀ of the equation, T_gI can be represented by an expression of the form T_gI ≈ T₀ + B/(A + 3). In the range of concentration above 50% by weight, A and B are almost independent of concentration but T₀ varies strongly. The nature of the secondary dispersions is also discussed.     

Moisture effects on the glass transition and the low temperature relaxations in semiaromatic polyamides

The influence of moisture absorption on the primary (glass) transition (T_a or T_g) and the low temperature relaxations of semiaromatic amorphous polyamides synthesized by isomeric aliphatic diamine and metha or para oriented phthalicdiacids has been investigated by means of differential scanning calorimeter (DSC) and dynamic mechanical thermal analyser (DMTA). The glass transition of semiaromatic polyamides was lowered due to the water absorption, and the β and the γ relaxations were as well. From the observed T_g and the difference in the heat capacity, the calculated T_g depression per 1 wt % water content was 12.3 K and the result was in good agreement with the experimental data. The depression of the glass transition may be expressed by the same manner as the plasticization of nylon 6 by water. The depressed β relaxation observed in the specimen containing a few percent of moisture was splitted into two transitions due to the reduction of water content, of which one was the elevation of the T_β and another was the simultaneous appearance of the T_γ, and then the single T_γ solely was observed for the completely dried specimen. The T_γ seemed to be merged into or not to be observed by the large and broad T_β transition when the sample was governed by a few percent of water, then it was emerged from the T_β due to water desorption. Thus, the T_β is believed to arise from the intermolecular hydrogen bonding between water molecules or between water and amide groups in wet polyamides. In addition, the γ relaxation originated from the peptide groups is attributable to the inter- and intramolecular hydrogen bonding between amide groups. © 1997 John Wiley & Sons, Inc. J Polyn Sci B: Polym Phys 35: 807–815, 1997     

Nuclear magnetic relaxation and molecular motion in poly(vinylidine fluoride)

Pulsed NMR T₁, T₂, and T_1ρ measurements are reported for poly(vinylidine fluoride) (PVF₂). The results demonstrate clearly the presence of four relaxation processes, three amorphous and one crystalline. The α relaxation is undoubtedly a crystalline one, while β and γ are both amorphous, in agreement with earlier conclusions from dielectric and dynamic mechanical measurements. The fourth relaxation (β′) observed initially in the mechanical measurements of Kakutani, but undetected in dielectric experiments, has been confirmed in our results and the process is described by an activation energy of 15.1 kcl/mole. Motion of folds on the surface of crystal lamellae is deemed to be the responsible mechanism for the β′ relaxation. Two models have been considered in the interpretation of the α process; rotation of crystalline chains in the vicinity of defects and rotational oscillation of restricted amplitude of all crystalline chains about the main chain axes. Rotation of amorphous chains is a possible mechanism for the γ process while motions of a general nature are responsible for the β relaxation. Our experimental results again indicate that spin diffusion plays an important role in the overall NMR response of the polymer.     

Relaxations in thermosets. XIX. Dielectric effects during curing of diglycidyl ether of bisphenol-A with a catalyst and the properties of the thermoset

Changes in the dielectric permittivity ε′ and loss epsiv;″ during the curing of DGEBA catalyzed by 10 mole % dimethylbenzylamine have been studied from sol to gel to glass formation regions at different temperatures from 323 to 390 K. The ε′ monotonically decreases with time of cure, and ε″ initially decreases by several orders of magnitude and then increases to reach a peak value before finally decreasing to a low value characteristic of the glassy state. The features shift to shorter times and the peak vanishes as the curing temperature is increased. The decrease of ε″ at the initial stage of cure has been analyzed in terms of dc conductivity σ₀, which follows a power law, σ₀ ∝? (t_g–t)^x, as well as a new singularity equation, σ₀ ∝? exp[–B/(t₀–t)] where t_g, x, B, and t₀ are empirical constants that vary with the curing temperature; t_g is close to the time for gelation; and t₀ ≥ time for vitrification. The dielectric properties of the thermoset formed after different periods of cure have been studied from 77 to 325 K. Similar studies of the thermosets formed at different temperatures have been made. Increase in the curing period decreases the heights of both the γ-and α-relaxation peaks and increases their separation, while a β-relaxation peak emerges. Isothermal curing at high temperatures decreases the height of the γ peak to a vanishingly small value and increases that of the β peak from a vanishingly small value. In both the uncured and fully cured states, there is only one sub-T_g relaxation process named γ for the uncured and β for the cured state. These results are discussed in terms of our general physical concepts of local mode motions in an amorphous matrix. © 1993 John Wiley & Sons, Inc.     

Dielectric studies of chain dynamics in homogeneous semi‐interpenetrating polymer networks

Semi‐interpenetrating polymer networks (semi‐IPNs) were prepared from linear polyurethane (PUR) and polycyanurate (PCN) networks. Wide‐angle X‐ray scattering measurements showed that the IPNs were amorphous, and differential scanning calorimetry and small‐angle X‐ray scattering measurements suggested that they were macroscopically homogeneous. Here we report the results of detailed studies of the molecular mobility in IPNs with PUR contents greater than or equal to 50% via broadband dielectric relaxation spectroscopy (10⁻²–10⁹ Hz, 210–420 K) and thermally stimulated depolarization current techniques (77–320 K). Both techniques gave a single α relaxation in the IPNs, shifting to higher temperatures in isochronal plots with increasing PCN content, and provided measures for the glass‐transition temperature (T_g) close to and following the calorimetric T_g. The dielectric response in the IPNs was dominated by PUR. The segmental α relaxation, associated with the glass transition and, to a lesser extent, the local secondary β and γ relaxations were analyzed in detail with respect to the timescale, the shape of the response, and the relaxation strength. The α relaxation became broader with increasing PCN content, the broadening being attributed to concentration fluctuations. Fragility decreased in the IPNs in comparison with PUR, the kinetic free volume at T_g increased, and the relaxation strength of the α relaxation, normalized to the same PUR content, increased. The results are discussed in terms of the formation of chemical bonds between the components, as confirmed by IR, and the reduced packing density of PUR chains in the IPNs. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3070–3087, 2000     

Segmental and secondary dynamics in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) blends

Broadband dielectric spectroscopy was used to study the segmental (α) and secondary (β) relaxations in hydrogen‐bonded poly(4‐vinylphenol)/poly(methyl methacrylate) (PVPh/PMMA) blends with PVPh concentrations of 20–80% and at temperatures from ?30 to approximately glass‐transition temperature (T_g) + 80 °C. Miscible blends were obtained by solution casting from methyl ethyl ketone solution, as confirmed by single differential scanning calorimetry T_g and single segmental relaxation process for each blend. The β relaxation of PMMA maintains similar characteristics in blends with PVPh, compared with neat PMMA. Its relaxation time and activation energy are nearly the same in all blends. Furthermore, the dielectric relaxation strength of PMMA β process in the blends is proportional to the concentration of PMMA, suggesting that blending and intermolecular hydrogen bonding do not modify the local intramolecular motion. The α process, however, represents the segmental motions of both components and becomes slower with increasing PVPh concentration because of the higher T_g. This leads to well‐defined α and β relaxations in the blends above the corresponding T_g, which cannot be reliably resolved in neat PMMA without ambiguous curve deconvolution. The PMMA β process still follows an Arrhenius temperature dependence above T_g, but with an activation energy larger than that observed below T_g because of increased relaxation amplitude. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3405–3415, 2004     

Effects of diluent on molecular motion and glass transitions in polymers. II. The system polyvinylchloride–tetrahydrofuran

Dielectric measurements, differential thermal analyses, and density measurements are reported on concentrated solutions of polyvinylchloride in tetrahydrofuran. The relaxation processes observed between 80 and 400°K have been classified into four types. From the analysis of experimental data, the primary process at the highest temperature and the process at the lowest temperature are assigned, respectively, to segmental motion of the polymer and motion of the solvent. Activation plots for the primary process conform to the Vogel–Tamman equation. The dielectric glass-transition temperature T'_g (defined as the temperature at which the dielectric relaxation time is 100 sec) determined with this equation agrees well with the glass-transition temperature T_g from thermal analysis. Therefore, T_g can be represented by an expression of the form The parameters of the Vogel–Tamman equation A and B are nearly independent of concentration, whereas T_o depends strongly on concentration. The dipole moment per monomeric unit calculated from the experimental data changes with concentration and exhibits steep increments around 30% and 90% by weight. The width of the distribution of the relaxation time also increases with the concentration. The results were compared with those for the system polystyrene–toluene studies in the same way.     

Effects of thermal history,crystallinity, and solvent on the transitions and relaxations in poly(bisphenol-A carbonate)

The following system of nomenclature for the transitions and relaxations in polycarbonate has been proposed: α = T_g = 150, β = 70, γ = ?100, and δ = ?220°C (frequency range of 10–50 Hz). The three component peaks of the γ relaxation are denoted by γ₁, γ₂, and γ₃ relaxations correspond to phenylene, coupled phenylene-carbonate, and carbonate motions, respectively. Dynamic mechanical analysis of poly(bisphenol-A carbonate) using the DuPont 981–990 DMA system shows that the magnitude of the β relaxation depends upon the thermal history of the polycarbonate; annealing greatly reduces the intensity of the β relaxation. A relaxation map constructed for the β relaxation gives an activation energy of 46 kcal/mol. Exposure of polycarbonate to methylene chloride vapor for various times shows that after an induction period of about 5 min the intensity of the γ₃ relaxation at ?78°C decreases whereas the intensity of the γ₁ relaxation of ?30°C is unaffected and the ratio E″(γ₁)/E″(γ₃) increases linearly with the square root of time. This has been ascribed to the interaction of methylene chloride on the carbonate group in polycarbonate. Thermal crystallization of polycarbonate does not affect the positions of the γ relaxation and the glass transition peaks, but merely reduces their intensity. The glass transition peak intensity falls off sharply in comparison to the γ relaxation intensity. Both the γ₃ and γ₁ peaks in polycarbonate have been observed simultaneously for the first time by dynamic mechanical analysis. Impact strength measurements show that methylene chloride treatment of polycarbonate results in a change in mode of failure from ductile to brittle with a resultant 40-fold reduction in impact energy for fracture. Thermally crystallized polycarbonate exhibits brittle fracture with very low force and energy at break.     

Pressure dependence of dielectric properties of chlorinated polyethylene vulcanizate. III. β relaxation

The effects of temperature and pressure on the shift factor and the dielectric increment of the β relaxation process were measured for vulcanized chlorinated polyethylene. The isobaric and isochoric activation enthalpies, H^*_P and H^*_V, the activation volume V^*, the pressure dependence of the glass–glass transition temperature, T_gβ/dP, and the apparent extinction temperature T_0β were obtained. The pressure dependences of both V^* and the dielectric increment would reach very small values near the liquid–glass transition temperature T_g, and the β process seems to be affected by the transition near T_g. The value of H^*v/H^*p for the β process is larger than that for the α process, and it is suggested that the molecular motions pertaining to the β process are more strongly restricted than those pertaining to the α process. The ratio T_0β/T₀, where T₀ is the characteristic temperature in the Vogel–Fulcher–Tammann–Hesse equation for the α process, follows the empirical relation of Matsuoka and Ishida, T_gβ/T_g ～0.75. The value of dT_gβ/dP estimated from T_g and T_0β/T₀ is consistent with the experimental value.     

Thermally stimulated discharge current studies on the effect of thermal treatment on the strength of polycarbonate

It is well known that polycarbonate annealed at 80–130°C undergoes gradual changes in mechanical properties. Annealing below T_g (ca. 150°C) results in a decrease in impact resistance and an increase in strength. Polycarbonate has three single relaxation processes and some distributed relaxation processes in the temperature range between 100 and 250°K (the β transition region). The effect of thermal pretreatment on the relaxation has been investigated by the thermally stimulated discharge current technique. Partial heating, peak cleaning, and theoretical fitting have also been performed and the activation parameters associated with the relaxation processes have also been calculated to assist in the analysis of the relationship between effects of annealing and structural motions in polycarbonate.