Electron-beam graft-modified membranes with externally controlled flux

Pre-irradiation grafting as a means to modify commerical poly(vinylidene fluoride) (PVDF) membranes has been studied. The membranes prepared were weak cation-exchange membranes (acrylic acid functionality), anion-exchange membranes (trimethyl ammonium functionality) and temperature-sensitive membranes (N-isopropyl amide functionality). Different graft loads were obtained by varying reaction time, radiation dose and in the case of acrylic acid the graft solution composition. The trimethyl ammonium chloride functionality was obtained by grafting vinyl benzyl chloride onto a PVDF membrane and aminating the benzyl chloride groups in a 45% trimethyl amine–water solution. For a membrane grafted with 9 wt% acrylic acid the flux increased approximately 70 times when the pH was decreased from 6 to 2. For a membrane with 5 wt% trimethyl ammonium functionality the flux increased both when pH was decreased below 3 and increased above 11. For a membrane grafted with 18 wt% N-isopropyl acrylamide a sharp increase of flux was observed when the temperature was raised above 32°C.     

Investigation and characterization of PVA-g-AAc/Zol membranes for possible practical use in separation processes

Poly(vinyl alcohol) films were grafted with two monomers (acrylic acid and N-vinyl imidazole) using the gamma irradiation technique. The melting temperature (T_m) and glass transition temperature (T_g) of the grafted membranes were determined with respect to the grafting yield. The ability of these membranes to separate cobalt from nickel has been investigated. The diffusion of cobalt and nickel ions from the feed compartment to the receiver compartment depends on the grafting yield and the pH of the feed solution. Cobalt ions do not diffuse through the membrane when the pH of the feed solution is >4.5. Thus, the prepared membranes could be considered for the separation of cobalt ions from nickel ions. The temperature of thermal decomposition of pure PVA-g-AAc/Zol membrane, PVA-g-AAc/Zol membranes containing cobalt ions, and PVA-g-AAc/Zol membranes containing nickel ions are determined using TGA analyzer; it was shown that the presence of cobalt and nickel increases the decomposition temperature. Also the membranes bonded with cobalt ions are more stable than the membranes containing nickel ions.     

聚砜与丙烯酸的紫外光辐射接枝共聚及其表征

在均相溶液体系下,运用紫外光辐射引发合成了聚砜与丙烯酸的接枝共聚物。用化学滴定、漫反射傅立叶变换红外光谱和热分析等技术对接枝聚合物进行了表征。结果表明:丙烯酸被接枝在聚砜链上;光照时间、单体浓度和光引发剂浓度对接枝率均有较大影响。膜表面接触角的研究表明,接枝共聚物膜的亲水性比改性前有所提高。     

Grafting of regenerated cellulose membrane by surface‐initiated atom transfer radical polymerization and its pH‐resposive behavior

Regenerated cellulose (RC) membranes which have pH modulated permeability have been prepared by anchoring the hydroxyl groups on the membrane surface with 2‐bromoisobutyryl bromide, followed by grafting with acrylic acid (AA) using atom transfer radical polymerization (ATRP). The obtained membranes were analyzed by X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared attenuated total reflection spectrometer (ATR‐FTIR), scanning electron microscopy (SEM), TGA and the results showed that AA had been grafted onto the membrane surfaces successfully. Then the pH modulated permeability properties were tested by water flux measurement. All results show that the pH modulated permeability properties of a RC membrane can be obtained by surface‐initiated ATRP. Copyright © 2010 John Wiley & Sons, Ltd.     

Greffage de l'acide methacrylique sur des films de poly(chlorure de vinyle) par la methode radiochimique directe

Since PVC films do not swell in pure methacrylic acid (MAA) the films were subjected to gamma-rays while dipped in various mixtures MAACHCl₂. Under such conditions, the grafting proceeds smoothly and its rate exhibits a flat maximum for the mixture containing ca. 50% (molar) monomer. The rate satisfies the relationship Rate = KI^0.6 and the over-all activation energy of the process is 4 kcal/mole. MAA grafted PVC films do not swell in solvents for PMAA (such as water or methanol) even for high grafting ratios. This result is unexpected since PTFE films grafted with either acrylic or methacrylic acid swell to a large extent in water and are excellent membranes. The swelling of the grafted PVC films was investigated in mixtures 1,2-dichloroethylene -methanol. It was found that the extent of swelling was highest in the mixture containing 35% methanol. The unusual swelling properties of these grafted films are attributed to strong polar interactions between PVC and PMAA chains.     

Radiation synthesis of acrylic acid onto poly(tetraflouroethylene-perflourovinyl ether) film: Chemical modifications and electrical conductivity

Graft-polymerization of acrylic acid (AAc) monomer onto poly(tetraflouroethylene-perflouro vinyl ether) (PFA) copolymer film was carried out using gamma irradiation technique to synthesize grafted copolymer film PFA-g-PAAc (PFA-COOH). The effect of the dose on the degree of grafting of AAc onto PFA film was investigated. The results showed that the degree of grafting increases with increasing the irradiation dose. The grafted [PFA-COOH] film was chemically modified by reaction with aniline to produce modified [PFA-CO-NH-ph] film, followed by sulphonation reaction to introduce sulfonic acid (SO₃H) groups to get other modified [PFA-CO-NH-ph-SO₃H] film. The chemical structures of the grafted and modified films were identified by FT-IR, XRD, and SEM. It is of particular interest to measure the electrical conductivity of grafted and modified membranes as a function of degree of grafting. It was found that the conductivity of the grafted films increases with increasing the degree of grafting, however a slightly increase in conductivity was observed in [PFA-CO-NH-ph-SO₃H] sample. The electrical conductivity property of the modified PFA membranes suggests their possible use for fuel cell applications.     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Gas-phase and liquid-phase pre-irradiation grafting of AAc onto LDPE and HDPE films for pervaporation membranes

A study has been made on gas-phase and liquid-phase pre-irradiation grafting of acrylic acid onto LDPE and HDPE films for pervaporation membranes of ethanol-water mixtures. It was found that the degree of grafting, percent volume change of grafted membranes and length of grafting chains depend on the methods of grafting, crystal state of substrate films and diffusion rate of the monomer in the films. The pervaporation characteristics of grafted membranes is influenced directly by the surface hydrophilicity of grafted membranes, temperature of the feed, degree of grafting, crosslinking of grafted chains and alkaline metal ions in the functional groups. The potassium ion exchange membrane of HDPE synthesized by gas-phase grafting has better pervaporation efficiency. At 80 wt% ethanol in the feed, 25°C feed temperature and 70% degree of grafting a grafted membrane has a 0.65 kg/m²h flux and a separation factor of 20.     

Preparation de membranes mosaiques par greffage radiochimique dans des films de polytetrafluoroethylene

Mosaic membranes were prepared by two successive grafting steps of acrylic acid and 4-vinyl-pyridine into well localized domains of polytetrafluoroethylene films. The films were subjected to X-rays through a grid-shaped shield which activated linear zones of the film 0.5 mm wide, separated by 0.5 mm of unactivated film. The films were then grafted with acrylic acid, neutralized and subjected to a second irradiation through a shield which protected the grafted zones. 4-Vinylpyridine was then grafted into the stripes left unchanged after the first treatment. The following properties of the resulting mosaic membranes were examined: swelling in water, electric conductivity and ion-pair diffusion. The coefficients of ion-pair diffusion were found to be 100–1000 times higher for the mosaic membranes than for carboxylic membranes of the same grafting ratio.     

Hydrophobically modified poly (acrylic acid) using calix[4]arene derivative. Ionophoric properties and extraction abilities toward alkali metal cations

p‐t‐Butyl calix[4]arene diol (distal cone) (1) was grafted with poly (acrylic acid) (PAA) to obtain hydrophobically modified PAA (PAA‐C) bearing calixarene moieties. The grafting method includes the direct esterification reaction of PAA with calixarene diol 1 which was carried out in a system of tosyl chloride (TsCl), pyridine (Py), and N,N‐dimethylformamide (DMF). The grafting yield was studied using different molar ratios of PAA to calix[4]arene diol 1, temperature, and reaction time. The chemical composition of the PAA‐C was studied by IR and ¹H NMR spectroscopy. Also, the morphology of PAA‐C was evaluated by scanning electron microscopy. The PAA‐C had different solubility and thermal properties. The extraction ability measurements of modified PAA toward alkali metal cations (Na⁺, K⁺, Cs⁺) and Ag⁺ showed a remarkable efficiency and selectivity of PAA‐C toward Na⁺. The main goal of this work was to design hydrophobically modified PAA with binding ability that is suitable for ion selective membranes and chemical sensor devices such as ion‐specific electrodes, semipermeable membranes, and quartz microbalances. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of poly(ε-caprolactone)-co-poly(acrylic acid) by radiation-induced grafting

Acrylic acid was grafted onto poly(ε-caprolactone) (PCL) films by using electron beam (EB) preirradiation technique. The effect of reaction time, monomer concentration, radiation dose, time between irradiation and grafting, radiation atmosphere, and polymer crystallinity on the extent of grafting were studied. Silver and tin ions were attached to the grafted chains in order to study the grafting process. The irradiation in air was initially more rapid, but the final extent of grafting was the same when irradiated in nitrogen atmosphere. Maximum grafting extents exceeding 400% could be obtained. The optimal grafting was obtained at an acrylic acid to water ratio of 30 : 70. The grafting process could be initiated at a dose as low as 12 kGy. The grafting process proved to start at the surface and was extended into the bulk with time. The ability to form crystals was reduced as the grafting extent increased. The water uptake of the poly(ε-caprolactone)-graft-poly(acrylic acid) was increasing with increasing grafting extent, but reached a maximum of ca 100% for all grafting extents above 85%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1805–1812, 1998     

Relations entre la structure et les proprietes des membranes de polytetrafluoroethylene greffe—I. Membranes monogreffees carboxyliques ou basiques

We have determined the equilibrium properties (neutralization and swelling and the transport properties: conductivity and dialysis) of hydrophilic membranes obtained by radiation grafting of acrylic acid or 4-vinylpyridine onto thin PTFE films. The presence of strong counter-ion-membrane interaction (PTFE-PAA-K⁺ and PTFE-P4VP-ClO^?₄) has been confirmed in the beginning of neutralization. The grafting ratios of the samples ranged between a few percent and several hundreds percent. The properties have been studied in connection with the average degrees of ionization and the average molalities of the reactive groups throughout the whole thickness of the membrane. The parameters of the synthesis which determine the structure of acid or basic grafted chains also have an influence on the properties of the resulting membranes. For a high dose-rate (> 100 rad min^?1), the properties of carboxylic membranes are related to the degree of cross-linking: for smaller dose rates, the properties are related to the length of the grafted branches and/or to the state of the skeleton of PTFE. For the basic membranes, the properties are controlled by the length of the grafted branches and the importance of the micro-phase-separation between PTFE and the grafted chains; for low dose rates, when the grafted branches are long, separation of hydrophobic and ionizable zones is noticed for grafting ratios higher than 5%. The carboxylic membranes with lower degrees of grafting, prepared with a high dose rate, exhibit very good permselectivity. The pyridinic membranes with a low degree of grafting could be of practical interest, viz. the manufacture of selective electrodes for perchlorate ions.     

Radiation‐grafted solid polymer electrolyte membrane: studies of fluorinated ethylene propylene (FEP) copolymer‐g‐acrylic acid grafted membranes and their sulfonated derivatives

Acrylic acid was grafted onto FEP by simultaneous radiation technique and the resulting membranes were sulfonated. Results of dynamic mechanical properties of the membranes showed that storage modulus and temperature at tan δ_(max) increases on grafting. X‐ray diffraction (XRD) analysis of the grafted and sulfonated membranes showed decreasing trend in crystallinity with increase in degree of grafting. From scanning electron microscopy (SEM) studies it was confirmed that grafting takes place by the front mechanism. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of SPE membrane based on sulfonated FEP‐g‐acrylic acid by radiation induced graft copolymerization for PEM fuel cell

A Novel solid polymer electrolyte (SPE) membrane containing both ? COOH and ? SO₃H group has been prepared by simultaneous method of radiation grafting of acrylic acid onto FEP followed by sulfonation. The presence of weakly acidic acrylic acid controls the swelling in water while ? SO₃H group provides conductivity due to its strongly ionic characteristic. FEP‐g‐acrylic acid and its sulfonated derivatives were characterized by their properties. While the mechanical properties decreased, other properties such as ion exchange capacity (IEC), water uptake and ionic conductivity increased with increase in graft content. These properties further changed on sulfonation. Acrylic acid being weakly acidic in nature, conductivity values of the grafted membrane were quite low. However, introduction of strong ? SO₃H group resulted in conductivity closer to Nafion 117. Few sulfonated membranes have been tested with respect to H₂/O₂ fuel cell performance. Short‐term fuel cell test for 100 hr gave a stable performance. These membranes are less expensive compared to Nafion. Copyright © 2004 John Wiley & Sons, Ltd.     

Gas transport in surface grafted polypropylene films with poly(acrylic acid) chains

This work describes the grafting reaction of poly(acrylic acid) (PA) onto the surface of polypropylene (PP) films carried out with ultraviolet radiation, using benzophenone as photoinitiator and water as solvent. By increasing the reaction time, graft percentages of 3.5, 6.5, 12.9, 19.8, 29.4, and 36.0% were obtained. Micrographs of the modified films show that grafting exclusively occurs on the PP films surface. The values of the permeability coefficient of oxygen, nitrogen, carbon dioxide, carbon monoxide, argon, methane, ethane, ethylene, and propane across the grafted films undergo a sharp drop. The interpretation of the permeation results suggest that radicals created in the tertiary carbons of the grafted chains by effect of UV light or by chain transfer reactions may highly crosslink the PA grafted layer. A rigid layer involving both strong hydrogen bonding and chains crosslinking is formed at grafting percentages of 3.5% that strongly hinders gas permeation across that layer. Destruction of hydrogen bonding by partially replacing protons of acrylic acid residues by sodium/silver cations increases the permeability of the surface grafted films. Finally, the films permselectivity is hardly affected by the grafted layer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2421–2431, 2007     

Hydrophilic modification of polyethersulfone membranes by low temperature plasma-induced graft polymerization

A complete and permanent hydrophilic modification of polyethersulfone (PES) membranes is achieved by argon plasma treatment followed by polyacrylic acid (PAA) grafting in vapor phase. Both Ar plasma treatment alone and post-PAA grafting rendered a complete hydrophilicity to the PES membranes. The hydrophilicity of the membranes treated with only the Ar plasmas is not, however, permanent. In contrast, the PES membranes treated with Ar plasma and subsequent acrylic acid (AA) grafting are permanently hydrophilic. High energy resolution X-ray photoelectron spectroscopy (XPS) confirmed the grafting of PAA to all surfaces of the membrane. Furthermore, water bubble point measurements remain unaffected. The pore sizes of the grafted membranes at higher grafting yield are slightly decreased. The modified membranes are less susceptible to protein fouling than the unmodified membranes and the pure water flux for the modified membranes was tremendously increased by plasma treatment. Furthermore, the modified membranes are easier to clean and required little caustic to recover permeation flux.     

Preparation of a superhydrophobic rough surface

The relationship between the contact angles, surface tension, and surface roughness is reviewed. Numerical formulas related to the superhydrophobic rough surfaces of polymers are predicted with two approaches, the Wenzel and Cassie–Baxter models. With these models as a guide, an artificial superhydrophobic surface is created. Rough nylon surfaces mimicking the lotus leaf are created by the coating of a polyester surface with nylon‐6,6 short fibers via the flocking process. Poly(acrylic acid) chains aregrafted onto nylon‐6,6 surfaces, and this is followed by the grafting of 1H,1H‐perfluorooctylamine onto the poly(acrylic acid) chains. Water contact angles as high as 178° are achieved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 253–261, 2007.     

Preparation of High‐capacity,Monodisperse Polymeric Weak Cation Exchange Packings Using Surface‐initiated Atom Transfer Radical Polymerization and Its Chromatographic Properties

A novel stationary phase for weak cation exchange (WCX) chromatography was prepared by "grafting from" strategy. Surface initiated atom transfer radical polymerization (ATRP) of acrylic acid (AA) was conducted in toluene medium, starting from the macromolecule initiators of poly(4‐vinylbenzyl chloride‐co‐divinylbenzene) (P_CMS/DVB) beads. The amounts of poly(acrylic acid) grafted chains with different ATRP formulations were calculated based on the elemental analyses. The poly(acrylic acid) grafted beads obtained with different ATRP formulations were tried as chromatographic packings in the separation of proteins by ion‐exchange chromatography. The effect of the poly(acrylic acid) grafted chain lengths on P_CMS/DVB beads for the separation of proteins was investigated in details. Simultaneously, characterization of the column was investigated as ion chromatographic stationary phase for the separation of inorganic cations. The results show that poly(acrylic acid) grafted columns had excellent performance for separation of proteins and inorganic cations. The highest of the dynamic capacity of the column was 35.55 mg/mL. The columns were provided with high column efficiency.     

Membranes permselectives obtenues par greffage radiochimique des acides acrylique et methacrylique sur des films de poly(chlorure de vinyle)

Membranes were prepared by subjecting to gamma-rays PVC films swollen in a mixture of acrylic acid and methylene chloride. The kinetics of the reaction were investigated as a function of monomer concentration, temperature and dose-rate. The swelling properties of the resulting membranes were studied as well as those of PVC films grafted with methacrylic acid. It was found that PVC films grafted with methacrylic acid only swell slightly in water even for high grafting ratios and the swelling is very slow. At elevated temperatures the films swell more quickly and reach a higher limiting swelling, but the effect is small. PVC films grafted with acrylic acid swell much more quickly and reach much higher swelling ratios. The extent of swelling markedly increases with temperature but this effect is not reversible: once the membranes have reached a high swelling ratio at elevated temperatures, they keep the same ratio when dipped in water at 20°. The Arrhenius plot of the swelling ratio exhibits a break at 50–60° apparently corresponding to a glass transition temperature. In methanol the swelling is significantly higher for PVC films grafted with methacrylic than with acrylic acid. Swelling of the membranes was also investigated in mixtures of water with methanol and methanol with methylene chloride. The results are interpreted by assuming a strong dipole-dipole interaction between the grafted branches and the trunk polymer resulting in a quasimolecular dispersion of the carboxylic chains in the PVC matrix. The latter acts as a barrier against the penetration of water. Heat treatment favours a segregation of the two polymeric species into microphases and this non-reversible transformation is assumed to be responsible for the unexpected behaviour of PVC films grafted with acrylic acid. The significant differences between the properties of PVC films grafted with either acrylic or methacrylic acid are attributed to the much higher hydrophobic character of the methacrylic chains.     

Chitosan/N-methylol nylon 6 blend membranes for the pervaporation separation of ethanol–water mixtures

Blend membranes of chitosan and N-methylol nylon 6 were prepared by solution blending. Their pervaporation performances for the separation of ethanol–water mixtures were investigated in terms of acid (H₂SO₄) post-treatment, feed concentration, blend ratio and temperature. The pervaporation performance of the blend membranes was significantly improved by ionizing with H₂SO₄. The blend ratio of chitosan and N-methylol nylon 6 plays a different role at feed solutions of low and high water content. At a feed solution having low water content, an increase in chitosan content caused a decrease in permeability and an increase in separation factor. At a feed solution having high water content, the permeability increases with an increase in chitosan content, while the separation factor shows a maximum value around 60 wt% chitosan. It is proposed that extra permeation channels generated from the phase separation boundary between ionized chitosan and N-methylol nylon 6 account for the abnormal temperature dependence of pervaporation performance of the blend membranes.