Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.     

Blend membranes from cellulose/konjac glucomannan cuprammonium solution

The blend membranes were prepared from cellulose/konjac glucomannan (KGM) cuprammonium solution by coagulating with aqueous 10 wt% NaOH solution, 20°C and 40°C water, respectively. Miscibility, pore morphology, structure, water permeability and mechanical properties of the blend membranes were investigated. The complex forms of cellulose/KGM in the mixed solutions, the effect of various coagulants and the percent content of KGM (w_KGM) on the structure and properties of the blend membrane are discussed. SEM and mechanical relaxation analysis indicate that the blend membranes are miscible in the range of 0–30 wt% of w_KGM. When w_KGM was smaller than 20 wt%, the tensil strength of the blend membrane coagulated by alkali aqueous solution was enhanced, corresponding to homogeneous structure and small pore size. However, blend membranes having a larger pore size (366 nm by SEM) and water permeability (560 ml/m² h mmHg) were obtained by coagulating the cellulose/KGM (70:30) cuprammonium solution with 40°C water, where ca. 20% of KGM as pore former were removed from the membrane.     

Thermal,mechanical and water barrier properties of graphene oxide/polyvinyl alcohol/polyol composite films

The novel polymer composite of polyvinyl alcohol (PVA), polyol(PO) and graphene oxide (GO) was used to prepare the PVA/PO and GO/PVA/PO with different weight percents of GO (0.5 and 1% denoted as (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO, respectively) through solution casting blend technique. The structure–properties of all used films were confirmed by scanning electron microscope (SEM), Transmission Electron Microscope (TEM), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) and mechanical properties. The SEM results exhibited the uniform and homogeneous dispersion of GO in the PVA/PO blend matrix. The TEM and XRD analysis confirmed the structure and exfoliation of GO nanosheets, respectively. Thermal stability suggested that (0.5 wt%)GO/PVA/PO and (1 wt%) GO/PVA/PO films are more stable than PVA/PO. The tensile strength of (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO films reached 270.5% and 1349.6%, respectively, which are higher than that of the PVA/PO film. The decrease in the water absorption (WA) of GO/PVA/PO was found from 110.5 to 38.4%. The physico-mechanical properties of used films suggested that the prepared GO/PVA/PO blend composite films can be applied in food packaging areas.     

魔芋葡甘聚糖/聚乙烯醇纳米纤维膜及其释药行为研究

为了研制药物缓释效果优良的薄膜材料,利用静电纺丝设备研制不同比重的魔芋葡甘露聚糖/聚乙烯醇纳米纤维膜,并通过扫描电镜、傅里叶变换红外光谱和示差扫描量热法表征纳米纤维膜的结构和性能,结合体外实验和数学模型研究其缓释行为.结果显示当魔芋葡甘露聚糖含量占纳米纤维膜总质量约76%时,纳米纤维膜中微纤丝粗细最均匀且结点较少,纳米纤维膜中魔芋葡甘聚糖和聚乙烯醇之间存在明显的相互作用,含有5-氨基水杨酸的纳米纤维膜在pH=7.4 PBS磷酸盐缓冲液中25 h的累积释放量大约为45%,显示出良好的药物缓释效果,其缓释行为与Higuchi模型具有较高的拟合度.研究表明利用静电纺丝设备研制的魔芋葡甘聚糖/聚乙烯醇纳米纤维膜可以为药物缓释载体的开发提供理论依据.     

Studies on the preparation of hydrolyzed starch-g-PAN (HSPAN)/PVA blend films--Effect of the reaction with epichlorohydrin

Absorbent hydrolyzed starch-g-PAN (HSPAN)/polyvinylalcohol (PVA) blend films crosslinked with epichlorohydrin (ECH) were prepared to overcome the phase separation and improve the mechanical properties of blend films. The absorbency of HSPAN/PVA blend films decreased with PVA contents due to the reduction of HSPAN contents which is known to play a major role in absorbing ability of the film. And also the absorbency decreased with the ECH contents due to the crosslinking reaction. As far as the solubility is concerned, it increased with PVA contents which is water soluble. But because of the crosslinking reaction between HSPAN and PVA by ECH, the solubility decreased with ECH contents. In the mechanical properties, the strength as well as the strain at break of the HSPAN/PVA blend films were improved very much if compared with HSPAN film, and those mechanical properties were improved even more by the reaction with ECH. The DSC thermograms of HSPAN films showed two major endothermic peaks at 32 and 128 °C, while those of PVA film showed two major endothermic peaks at 49 and 190 °C. In the non-crosslinked blend films, each four endothermic peak was apparent. But as the ECH content increased, both peaks at 128 and 190 °C disappeared and a new peak appeared at the intermediate temperature. In other words, the compatibility of blend films was increased by the reaction with ECH. Also, from the results of TGA, it was confirmed that the thermal degradation of blend films was decelerated by the crosslinking reaction.     

Structure and Mechanical Properties of Chitosan/Poly(Vinyl Alcohol) Blend Films

Summary: The origins of the thermal and mechanical properties of chitosan and poly(vinyl alcohol) (PVA) with inter- and intra-hydrogen bonds were investigated systematically by using X-ray, DSC, positron annihilation and viscoelastic measurements. Based on their individual properties, the characteristics of the blend films were estimated in relation to their morphology and mechanical properties as a function of chitosan content. The characteristics of the blend films were also analyzed in terms of the deviation from a simple additive rule of chitosan and PVA content. These results suggested that the miscibility of chitosan and PVA could be ensured by entanglement of the amorphous chain segments of chitosan and PVA. Further detailed analysis revealed that the chitosan content on the film surface is higher than that of the admixture content of chitosan after elongation, although the chitosan and PVA chains were crystallized independently. The elongation could be achieved for the blend films whose PVA content was higher than 50% and the drawn blend films were transparent. Thus, it may be expected that sufficiently entangled meshes formed between chitosan and PVA amorphous chains within the film, the PVA content being higher than 50%, were maintained under the elongation process.     

聚乙烯醇/单宁共混膜的制备及其抗菌性能

采用溶液共混浇膜法制备了不同单宁含量的聚乙烯醇/单宁共混膜材料,利用扫描电镜(SEM)、广角X-射线衍射(WAXD)及示差扫描量热分析(DSC)对共混膜的结构进行了表征.结果表明,单宁和聚乙烯醇具有良好的相容性,聚乙烯醇的结晶能力及熔点均随单宁的加入量增大而稍降低.少量戊二醛的轻度交联作用使单宁在共混膜中非常稳定,在水中浸泡24 h后也仅有不到1.8%的单宁(相对膜中单宁总质量)渗出.接触法抗菌试验表明,所制备的共混膜对大肠杆菌(E.coli,CMCC 44103)、金黄色葡萄球菌(S.aureus,ATCC6538)和表皮葡萄球菌(S.epidermidis,ATCC 12228)都具有良好的抗菌能力,且随着单宁含量的升高而增强.     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

纤维素/甲壳素共混膜的结构表征与抗凝血性能

以 6wt %NaOH 4wt%尿素为纤维素的新溶剂 ,采用溶液共混法制备出纤维素 甲壳素共混膜 ,为甲壳素在碱性溶液中制膜提供了新的方法 .红外光谱、X 射线衍射、扫描电镜和力学性能、抗凝血性能测试结果表明 ,共混膜中甲壳素含量低于 4 0wt%时 ,纤维素与甲壳素分子间具有良好的相容性 ;在纤维素中引入适量甲壳素可提高共混膜的抗张强度 ,共混膜的干、湿态抗张强度在甲壳素含量 10wt%时最大 ,其值分别为 89 1MPa和 4 3 7MPa ,比纯态纤维素膜的干、湿态抗张强度分别提高了 6 7%和 11 5 % ;甲壳素的引入可明显降低血小板在共混膜表面的粘附、凝聚与变性 ,增大共混膜的抗凝血参数 ,甲壳素含量达到 5 0wt%时 ,该共混膜具有良好的抗凝血性能     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

PREPARATION AND PHYSICAL PROPERTIES OF BLEND FILMS FROM SODIUM ALGINATE AND POLYACRYLAMIDE SOLUTIONS

Blend films of sodium alginate and polyacrylamide (PAAm) were prepared by mixing the aqueous solution of both samples at a different ratio. All blend films obtained are optically clear to the naked eye. The structure and physical properties of the films were studied by FT-infrared (FT-IR), wide angle X-ray diffraction (WAXD), differential thermal analysis (DTA), thermogravimetic analysis (TGA), scanning electron microscopy (SEM), and tensile strength test. The results showed that the occurrence of interactions between -COO^?, -OH groups of sodium alginate and -CONH₂ groups of PAAm in the blends through hydrogen formation. The blend films exhibited the higher thermal stability and improved mechanical properties in dry states. These properties had the maximum value around 20 wt% PAAm content in the blend film. The morphological transition of the blend films from sodium alginate-like to PAAm-like was observed by scanning electron microscopy.     

Influence of the nanoparticle type on the thermal decomposition of the green starch/poly(vinyl alcohol)/montmorillonite nanocomposites

In this study, some aspects concerning the thermal decomposition of starch/poly(vinyl alcohol) (PVA)/montmorillonite (MMT) nanocomposites with 2 wt% nanoclay, prepared by melt mixing method, were studied. For these loadings, the inorganic fillers are well dispersed through the PVA/starch matrix, i.e., the nanocomposites formed are mostly intercalated hybrids. The aim of this article is to establish the effect of the nanofiller nature on the thermal decomposition of the starch/PVA/MMT nanocomposites. The thermal behavior of the 50 wt% starch/50 wt% PVA blend and its nanocomposites with 2 wt% nanoclay has been investigated by thermogravimetric analysis coupled with Fourier transform-infrared spectroscopy and mass spectrometry (MS). The volatile compounds resulting during the thermal degradation were studied by in situ vapor phase FT-IR spectroscopy and MS technique under a controlled temperature/time program. Apart from the identification of the volatile compounds, some conclusions on the nanoclays effect on the degradation mechanism and formation of the volatile compounds in accordance with the previously developed general mechanisms for PVA and starch degradation have been formulated. The clay–PVA/starch nanocomposites show completely different degradation product distribution patterns, which may be attributed to the presence of the head-to-head structures and Si–O–C linkages formed between clay and blend components.     

Investigation of Miscibility of Linseed Oil Epoxy with Poly(vinyl alcohol)

Blending of two polymers in solution is a simple and cost effective technique to improve upon the physical and mechanical properties of the component polymers. Maximum synergism in the properties of the two polymers occurs when they are thermodynamically miscible. Poly(vinyl alcohol) (PVA) yields tough, flexible and water sensitive films. Linseed oil epoxy(LOE), a product from sustainable resource, used as a plasticizer and corrosion resistant coating, does not produce free standing film. A blend of PVA with LOE may yield films of good toughness and flexibility, and low water absorption if the two components are miscible with each other. Blends of PVA with LOE were prepared in weight ratios 80/20, 60/40, 40/60 and 20/80 through solution method by mixing in dimethyl sulphoxide. In the first instance, the miscibility the two components were investigated using the techniques of viscosity and ultrasonic measurements. The study revealed that the two components showed miscibility up to below 60 wt% PVA in the blend as at the composition LOE: PVA 40/60, phase inversion occurs. Above this composition, immiscibility is indicated; differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) delineates the above behavior in the solid phase.     

Dehydration of acetic acid by pervaporation using SPEK-C/PVA blend membranes

Sulfonated cardo polyetherketone (SPEK-C) and poly(vinyl alcohol) (PVA) blend membranes were prepared by solution casting method and used in pervaporation (PV) dehydration of acetic acid. The membranes were characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and contact angle meter. The results show that thermal crosslinking occurred to the membrane under high temperature annealing. The effective d-spacing (inter-segmental spacing) decreased with PVA content decreasing. The hydrophilicity of the blend membrane increased with SPEK-C content increasing. Swelling and sorption experiments show that the swelling degree of the blend membrane increased, however both the sorption and diffusion selectivities decreased with increasing PVA content. The diffusion selectivity is higher than the sorption selectivity. This suggests that PV dehydration of acetic acid is dominated by the diffusion process. The pervaporation separation index (PSI) of the membrane increases with increasing PVA content and arrives at a maximum when the SPEK-C/PVA ratio is 3/2, then decreases with further addition of PVA. The membrane has an encouraging separation performance with a flux of 492 g m⁻² h⁻¹ and separation factor of 59.3 at 50 °C at the feed water content 10 wt%.     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Preparation and characterization of cellulose and konjac glucomannan blend film from ionic liquid

Blend films from cellulose and konjac glucomannan (KGM) in room temperature ionic liquid 1‐allyl‐3‐methylimidazolium chloride were satisfactorily prepared by coagulating with water. The composition of the blend films was gravimetrically analyzed, and the compatibility of the two natural polymers was characterized by Fourier transform infrared spectroscopy and wide‐angle X‐ray diffraction. The results indicate good compatibility and strong interactions between cellulose and KGM, resulting in almost no loss of the water‐soluble KGM from the blend films even after the water coagulating and washing. However, microstructure analyses portrayed phase separations in the blend films, namely, egg‐like new phase particles were embedded in a continuous matrix base (MB). Phase diagram analysis and differential scanning calorimetry of the phase inversion coagulation process suggest that relative low molecular mass part of both cellulose and KGM formed the continuous MB, whereas the egg‐like new phase particles were super patterns of relative high molecular mass of both polymers, which played an important role in strengthening the blend material. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1686–1694, 2009     

Morphology and mechanical properties of poly(vinyl alcohol) and starch blends prepared by gelation/crystallization from solutions

 In an attempt to produce biodegradation materials, poly(vinyl alcohol) (PVA)–starch (ST) blends were prepared by gelation/crystallization from semidilute solutions in dimethyl sulfoxide (Me₂SO) and water mixtures and elongated up to 8 times. The content of mixed solvent represented as Me₂SO/H₂O (volume percent) was set to be 60/40 assuring the greatest drawability of PVA homopolymer films. The PVA/ST compositions chosen were 1/1, 1/3, and 1/5. The elongation up to 8 times could be done for the 1/1 blend but any elongation was impossible for blends whose ST content was beyond 50%. When the blends were immersed in water at 20 or 83 °C, the solubility became considerable for an undrawn blend with 1/5 composition and a drawn 1/1 blend with λ=8. To avoid this phenomenon, cross-linking of PVA chains was carried out by formalization under formaldehyde vapor. Significant improvement could be established by the cross-linking of PVA chains. For the 1/1 blend, the amount of ST dissolved in water at 23 °C was less than 3% for the undrawn state and 25% for the drawn film. The decrease in the ST content was enough for use as biodegradation materials. Namely, the water content relating to the biodegradation in soil is obviously different from such a serious experimental condition that a piece of blend film was immersed in a water bath. At temperatures above 0 °C, the storage modulus of the formalization blends became slightly higher than those of the nonformalization blends. The Young's modulus of the drawn films with a draw ratio of 8 times was 2 GPa at 20 °C. Received: 23 June 2000 Accepted: 30 October 2000     

The role of hydrogen-bonding interaction in poly(vinyl alcohol)/poly(acrylic acid) blending solutions and their films

<正>The aim of this work is to investigate the hydrogen-bonding interaction in poly(vinyl alcohol)(PVA)/poly(acrylic acid)(PAA) blending system and its influence on rheological properties in solution and the physical properties in solid state. Introducing PAA into PVA solutions resulted in a thickening behavior of blend solutions.The viscosity of the solutions increased with PAA content increasing,and a maximum viscosity could be obtained when the ratio of PVA/PAA was 70/30. The intermolecular hydrogen-bonding and miscibility between PVA and PAA in solid state were investigated by differential scanning calorimetry(DSC),Fourier transform infrared spectroscopy(FTIR) and mechanical measurements.The results displayed the great influence of introducing PAA on the properties of blending films.The tensile strength increased from 89.31 MPa to 119.8 MPa and Young's modulus improved by over 300%with increasing PAA concentration compared with those of pure PVA films.By systematically studying the rheological behaviors of solutions and the physical properties of films,the influence of hydrogen-bonding in solutions and solid states were discussed.     

MISCIBILITY, THERMAL STABILITY AND RETENTION OF PVP FOR CROSSLINKED PVA/PVP BLENDS

The thermal behavior, miscibility, crystallite conformation and thermal stability ofcrosslinked(CL-) PVA/PVP blends were studied by DSC and TG methods, respectively. DSCresults showed that in the blend, the crystallinity,T_m and T_c of PVA were obviously lower thanthose of pure PVA; the crystal growth changed from three dimensional to two dimensional andonly a single T_g was detected. These facts demonstrated that this crystalline and amorphousblend have good miscibility. TG curves showed that providing the quantity of K_2S_2O_8 added ismore than 3 wt%,in the blends PVA will form a stable CL-network, whose thermal degradationtemperature was near to that of PVP. But crosslinking reaction will not take place for PVP. Theprocesses of thermal degradation of CL-blends are based on combining both the thermaldegradation of PVP and that of PVA crosslinked with corresponding quantity of K_2S_2O_8 CL-agent, respectively. The UV measurements showed that 75 wt% of PVP may be remained in CL-blend hydrogelscrosslinked by adding (3--5 wt% )K_2S_2O_8. This is mainly due to the stable CL-network formed and the good compatibility and properentanglement between the composites in the CL-blends.     

Preparation of gelatin/poly(vinyl alcohol) film modified by methyl methacrylate and gamma irradiation

The properties of gelatin–polyvinyl alcohol (G–PVA) blend films were improved by methyl methacrylate (MMA) and γ irradiation for a practical viewpoint. The films were prepared by the casting method, modified by glycerol and MMA monomer, and their mechanical properties were also studied. The gelatin-based films were successfully prepared using γ irradiation (3.1 kGy) and gelatin: PVA = 97:3 (w/w) as optimized. Tensile properties of the films were studied and thermal properties of the films were characterized by thermogravimetric analysis and dynamic mechanical analysis pointed out that MMA treated both gelatin films, and G–PVA blend films showed less thermal degradation than untreated films. In addition, structural and morphological features of the gelatin-based films were examined by Fourier transform infrared and scanning electron microscopy, respectively. The ultimate results of the present study showed remarkable enhancement in tensile properties (> 40%) and a reduction in elongation at break of the films, thanks to the MMA addition and γ irradiation.