Acrylamide/maleic acid hydrogels

Acrylamide/maleic acid hydrogels in the form of rods were prepared by γ-irradiating ternary mixtures of acrylamide–maleic acid–water with 2.00–5.71 kGy γ-rays. The influence of dose and relative content of maleic acid on the spectroscopic, thermal and mechanical properties, swelling properties, diffusional behavior of water and diffusion coefficients of hydrogel systems are examined. Acrylamide/maleic acid hydrogels were swelled in the range of 1000–2800%, While polyacrylamide hydrogels were swelled in the range of 650–700%. Water diffusion to hydrogels in non-Fickian type diffusion. The diffusion coefficients varied from 4.5 × 10^?2 to 12.2 × 10^?7 cm² sec^?1.     

Conducting hydrogels based on semi‐interpenetrating networks of polyaniline in poly(acrylamide‐co‐itaconic acid) matrix: synthesis and characterization

In this work, acrylamide/itaconic acid copolymeric hydrogels are prepared by free radical polymerization initiated by redox initiators of potassium persulfate and N ,N ,N ′,N ′‐tetramethyl ethylene diamine; N ,N ′methylene bisacrylamide was employed as a crosslinking agent. Aniline monomer was absorbed in the network of poly(acrylamide‐co‐itaconic acid) P(AAm‐co‐IA) hydrogel and followed by gamma radiation induced polymerization at room temperature. The novel semi‐interpenetrating network was comprised of linear polyaniline immersed in P(AAm‐co‐IA) matrix. Electrical conductivity of the hydrogels was measured using four‐probe technique. The conductivities for the prepared hydrogels are found to increase from 5.5 × 10^?7 S cm^?1 for P(AAm‐co‐IA) alone to 4.4 × 10^?3 S cm^?1 for semi‐interpenetrating polymer network P(AAm‐co‐IA)/polyaniline. Thus, a new composite hydrogel with good conductive properties also displaying enhanced mechanical strength and pH sensitivity was prepared. Copyright © 2017 John Wiley & Sons, Ltd.     

Adsorption of Uranyl Ions into Poly(Acrylamide‐co‐Acrylic Acid) Hydrogels Prepared by Gamma Irradiation

Acrylamide (AAm)/Acrylic Acid (AAc) copolymers have been prepared by gamma irradiation of binary mixtures at three different compositions where the acrylamide/acrylic acid mole ratios varied around 15, 20, and 30%. Threshold dose for 100% conversion of monomers into hydrogels was found to be 8.0 kGy. Poly(Acrylamide‐co‐Acrylic Acid) (poly(AAm‐co‐AAc)) hydrogels have been considered for the removal of uranyl ions from aqueous solutions. Swelling behavior of these hydrogels was determined in distilled water at different pH values and in aqueous solutions of uranyl ions. The results of swelling tests at pH 8.0 indicated that poly(AAm‐co‐AAc) hydrogel, containing 15% acrylamide showed maximum % swelling. Diffusion of water and aqueous solutions of uranyl ion into hydrogels was found to be non‐Fickian in character and their diffusion coefficients were calculated. The effect of pH, composition of hydrogel, and concentration of uranyl ions on the adsorption process were studied at room temperature. It was found that one gram of dry poly(AAm‐co‐AAc) hydrogel adsorbed 70–320 mg and 70–400 mg uranyl ions from aqueous solutions of uranyl nitrate and uranyl acetate in the initial concentration range of 50–1500 mg UO₂ ²⁺L^?, depending on the amount of AAc in the hydrogels, respectively. Adsorption isotherms were constructed for poly(AAm‐co‐AAc)–uranyl ion system indicating an S type of adsorption in the Giles classification system. It is concluded that crosslinked poly(AAm‐co‐AAc) hydrogels can be successfully used for the removal of uranyl ions from their aqueous solutions.     

The Influence of Preparation Methods on the Swelling and Network Properties of Acrylamide Hydrogels with Crosslinkers

Abstract

Using different types and concentrations of crosslinkers, acrylamide (AAm) hydrogels have been prepared with chemical initiation and gamma irradiation techniques. The effects of the preparation method, crosslinkers type and concentration on swelling behavior of AAm hydrogels were investigated. Swelling was performed in distilled water and followed gravimetrically. Swelling parameters such as equilibrium swelling degree, equilibrium water content (EWC), maximum swelling, initial swelling rate, diffusion exponent and coefficient, and network parameters such as molecular mass between crosslinks, crosslink density, mesh size, and porosity were calculated and evaluated. The range of equilibrium swelling degree of AAm hydrogels was varied from 255% to 1450% depending upon the preparation method, crosslinker type, and crosslinker concentration. The diffusion of water into AAm hydrogels was found to be nonFickian.     

(Sodium Alginate/Acrylamide) Semi‐Interpenetrating Polymer Networks and their Usability on Removal of Lead,Cadmium, Nickel Ions

In this study, (sodium alginate (NaAlg)/acrylamide (AAm)) interpenetrating polymer networks (IPN) have been prepared at three different compositions, where the sodium alginate composition varies 1, 2, and 3% (w/v) in 50% (w/v) acrylamide solutions. These solutions have been irradiated with a ⁶⁰Co‐γ source at different doses. The percent conversion was determined gravimetrically and 100% gelation was achieved at the 10.0 kGy dose. The swelling results at pH 7.0 and 9.0 indicated that (NaAlg/AAm)3IPN hydrogel, containing 3% NaAlg showed maximum % swelling in water, with swelling increasing in the order of Ni²⁺>Cd²⁺>Pb²⁺. Diffusion in aqueous solutions of metal ions within (NaAlg/AAm)IPN hydrogels was found to be Fickian character. Diffusion coefficients of (NaAlg/AAm)IPN hydrogels in water and aqueous solutions of metal ions were calculated. The maximum weight loss temperature and half life temperature for NaAlg, PAAm, (NaAlg/AAm)IPN and (NaAlg/AAm)IPN‐metal ion systems were found from thermal analysis studies. In the adsorption experiments, the efficiency of (NaAlg/AAm)IPN hydrogels to adsorb nickel, cadmium and lead ions from water was studied. (NaAlg/AAm)IPN hydrogels showed different adsorption for different aqueous solution of metal ion at pH 7.0. Adsorption isotherms were constructed for the (NaAlg/AAm)IPN‐metal ion systems. S type adsorption in the Giles classification system was found.     

Water uptake and dye sorption studies of chemically crosslinked highly swollen novel ternary acrylamide‐based hydrogels including citraconic acid and sodium acrylate

Highly swollen hydrogels made by the polymerization of acrylamide (AAm) with some anionic monomers such as citraconic acid (CITA) and sodium acrylate (SA) were investigated as a function of composition to find materials with swelling and dye sorption properties. Highly swollen AAm/CITA/SA or AAm/SA/CITA hydrogels were prepared by free radical solution polymerization in aqueous solutions of AAm with CITA and SA as co‐monomers and two multifunctional crosslinkers such as ethylene glycol dimethacrylate (EGDMA) and 1,4‐butanediol dimethacrylate (BDMA). Swelling experiments were performed in water at 25°C, gravimetrically. Chemically crosslinked AAm/CITA/SA or AAm/SA/CITA hydrogels were used in experiments on sorption of water‐soluble monovalent cationic dye such as “Nil blue” (Basic Blue 12; BB 12). Equilibrium percentage swelling values of AAm/CITA/SA or AAm/SA/CITA hydrogels were calculated in the range of 1797–22,098%. Some swelling kinetic parameters were found. Diffusion behavior of water was investigated. Water diffusion into the hydrogels was found to be non‐Fickian in character. For sorption of cationic dye, BB 12 into the hydrogels was studied by batch sorption technique at 25°C. AAm/CITA/SA or AAm/SA/CITA hydrogels in the dye solutions showed coloration, whereas AAm hydrogel did not show sorption of any dye from the solution. The sorption capacity of AAm/CITA/SA or AAm/SA/CITA hydrogels was investigated. At the end of the experiments, 21.70–78.91% BB 12 adsorptions were determined. Copyright © 2007 John Wiley & Sons, Ltd.     

Biochemical and Kinetic Study of Laccase from Ganoderma cupreum AG-1 in Hydrogels

In the present study, three different types of hydrogels i.e., (poly (?acrylamide)/alginate (P (AAm)/Alg), poly (acrylamide-N-isopropylacrylamide) (P (AAm-NIPA)), and poly (acrylamide-N-isopropylacrylamide)/alginate (P (AAm-NIPA)/Alg)) were synthesized by acrylamide, alginate, and N-isopropylacrylamide for the entrapment of laccase. The hydrogel-entrapped and free laccase showed optimum temperature of 50 °C for the oxidation of ABTS, but the entrapped laccase showed high temperature, pH, and storage stability as compared to the free enzyme. The K _m values of free laccase, (P (AAm)/Alg)-L, (P (AAm-NIPA))-L, and (P (AAm-NIPA)/Alg)-L were found to be 0.13, 0.28, 0.33, and 0.50 mM, respectively. The V _max values of free laccase, (P (AAm)/Alg)-L, (P (AAm-NIPA))-L, and (P (AAm-NIPA)/Alg)-L were found to be 22.22?×?10², 5.55?×?10², 5.0?×?10², and 4.54?×?10² mM/min, respectively. The entrapped laccase hydrogels were used for the decolorization of Reactive Violet 1 dye, with 39 to 45 % decolorization efficiency till the 10th cycle.     

Swelling equilibria and dye adsorption studies of chemically crosslinked superabsorbent acrylamide/maleic acid hydrogels

Superswelling acrylamide (AAm)/maleic acid (MA) hydrogels were prepared by free radical polymerization in aqueous solution of AAm with MA as comonomer with some multifunctional crosslinkers such as trimethylolpropane triacrylate and 1,4-butanediol dimethacrylate. AAm/MA hydrogels were used in experiments on swelling and adsorption of a water-soluble monovalent cationic dye such as Basic Blue 17 (Toluidin Blue). As a result of dynamic swelling tests, the influence of relative content of MA on the swelling properties of the hydrogel systems was examined. AAm/MA hydrogels were swollen in the range 1660-6050% in water, while AAm hydrogels swelled in the range 780-1360%. Equilibrium water content of AAm/MA hydrogels were calculated in the range 0.8873-0.9837. Water intake of hydrogels followed a non-Fickian type diffusion. The uptake of the cationic dye, BB-17 to AAm/MA hydrogels is studied by batch adsorption technique at 25 °C. In the experiments of the adsorption equilibrium, S-type adsorption in Giles's classification system was found. The binding ratio of hydrogel/dye systems was gradually increased with the increase of MA content in the AAm/MA hydrogels.     

Influence of some amino acids on the dynamic swelling behavior of radiation-induced acrylamide hydrogel

The influence of some amino acids—alanine, glycine, valine, glutamine, histidine, phenylalanine, and tryptophan—on the swelling behavior of acrylamide (AAm) hydrogel prepared by γ-radiation was investigated. Swelling experiments of AAm hydrogel were made in the universal buffer solutions and the amino acid solutions at certain pHs at 37°C. These selected pH values were pK₁, pK₂ and isoelectric point (pI) values such as ionization of α-carboxyl groups, ionization of α-amino groups, and the pIs of the amino acids, respectively. The swelling of AAm hydrogel increased when pH values of solutions were increased. The value of equilibrium swelling of AAm hydrogel in the solution of universal buffer was 880% at pH 10.0, whereas it was 670% at pH 2.0. The values of equilibrium swelling of AAm hydrogel in amino acid solutions were between 830 and 965% at pH 10.0, whereas they were between 635 and 775% at pH 2.0. The rate constant of swelling, initial swelling rate, theoretical maximum swelling, diffusional exponent, network parameter, and diffusion coefficient were calculated by swelling kinetics. Diffusions of the amino acid solutions into the hydrogel were generally found as non-Fickian in character. The diffusion coefficients of the hydrogel were between 0.91 × 10⁻⁶ and 2.41 × 10⁻⁶ cm²/s.     

Synthesis of poly (acrylamide-co-aconitic acid) adsorbents by gamma-irradiation,characterization, adsorption studies and application for cationic dyes removal

In this study, acrylamide (AAm)/aconitic acid (ACA) copolymers were prepared with two different mol% of aconitic acid 4%, 17% and were irradiated with gamma irradiation at different irradiation doses (4 - 25kGy). The percent yield was assigned by gravimetrical method. The effect of irradiation dose, pH and involved amounts of monomers (AAm/ACA) in hydrogels on swelling properties were investigated. The conversion of monomers to hydrogels was 100% at 25kGy. Poly(acrylamide-co-aconitic acid) P(AAm/ACA) hydrogels have been used for the adsorption of some aqueous solutions of dyes such as Methylene Blue (MB) and Safranine-O (S). The hydrogels were swollen in distilled water at pH 3, 5, 7, 8 and in aqueous solutions of dyes. The initial swelling rates of hydrogels are increased by increasing of pH. The effects of concentration of the aqueous solutions of dye and hydrogel composition on the adsorption were investigated. The adsorption is increased and changed depending on the structure of dye and composition of hydrogel.     

Swelling behavior of strong polyelectrolyte poly(N-t-butylacrylamide-co-acrylamide) hydrogels

Temperature-sensitive ionic hydrogels based on N-t-butylacrylamide (TBA), acrylamide (AAm), 2-acrylamido-2-methylpropane sulfonic acid sodium salt (AMPS) and N,N^′-methylenebis(acrylamide) (BAAm) monomers were prepared. The molar ratio of TBA to the monomers AAm and AMPS was fixed at 60/40, while the AMPS content of the hydrogels was varied. The elastic modulus of the hydrogels was in the range of 347-447 Pa, much lower than the modulus of PAAm or poly(N-isopropylacrylamide) hydrogels due to the reduced crosslinking efficiency of BAAm in TBA/AAm copolymerization. The hydrogels exhibited swelling-deswelling transition in water depending on the temperature. Increasing ionic group (AMPS) content resulted in shifting of the transition temperature interval in which the deswelling takes place. The higher the ionic group content, the broader the temperature interval at the phase transition. Ionic hydrogels exhibited first-order reentrant conformational transitions in ethanol-water and in dimethylsulfoxide (DMSO)-water mixtures. The higher the ionic group content of the hydrogels the narrower the ethanol (or DMSO) range in which the reentrant phenomena occur. By taking into account the difference of the solvent mixture composition inside and outside the gel, the equilibrium swelling theory provided a satisfactory agreement to the experimental swelling data of the hydrogels immersed in the solvent mixtures.     

Synthesis and Characterization of pH‐sensitive Poly(IA‐co‐AAc‐co‐AAm) Hydrogels via Frontal Polymerization

In this work, we report a series of poly(itaconic acid‐co‐acrylic acid‐co‐acrylamide) (poly(IA‐co‐AAc‐co‐AAm)) hydrogels via frontal polymerization (FP). FP starts on the top of the reaction mixture with aid of heating provided from soldering iron gun. Once polymerization initiated, no further energy is required to complete the process. The influences of IA/AAc weight ratios on frontal velocities, temperatures, and conversions on the reaction time are thoroughly investigated and discussed where the amount of AAm monomer remains constant. Fourier transform‐infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscope (SEM), dynamic mechanical analysis, and the swelling measurement are applied to characterize the as‐synthesized poly(IA‐co‐AAc‐co‐AAm) hydrogels. Interestingly, the swelling ratios of the hydrogels are changed with different IA/AAc contents, and the maximum swelling ratios are ~4439% in water. SEM images describe highly porous morphologies and explain good swelling capabilities. Moreover, the poly(IA‐co‐AAc‐co‐AAm) hydrogels exhibit superior pH‐responsive ability. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2214–2221     

Swelling characterization of novel ternary semi‐IPNs: acrylamide/1‐vinylimidazole/PEG hydrogels

New ternary semi interpenetrating polymer networks (semi‐IPNs) systems containing acrylamide (AAm), 1‐vinylimidazole (VI) and poly (ethylene glycol) (PEG) have been prepared. AAm/VI hydrogels and semi‐IPN's, poly (AAm/VI/PEG) with 0.25, 0.50, 0.75 and 1.00 g of PEG (per 1.00 g AAm) were prepared by free radical solution polymerization in aqueous solution of AAm with VI as comonomer and a multifunctional crosslinker such as 1,4 butanediol dimethacrylate (BDMA). Swelling experiments were performed in water at 25°C, gravimetrically. The influence of VI and PEG content in hydrogels were examined. AAm/VI and AAm/VI/PEG hydrogels showed large extents of swelling in aqueous media, the swelling being highly dependent on the chemical composition of the hydrogels. Percentage swelling ratio of AAm/VI hydrogels and AAm/VI/PEG hydrogels was shown as 650–4167%. The values of equilibrium water content (EWC) of the hydrogels are between 0.8990 and 0.9750. Diffusion behavior was investigated. Water diffusion into hydrogels was found to be non‐Fickian in character. Copyright © 2007 John Wiley & Sons, Ltd.     

Phase Transition of Acrylamide‐Based Polyampholyte Gels in Water

The swelling behavior of acrylamide (AAm)–based polyampholyte hydrogels in water and in aqueous salt (NaCl) solutions was investigated. [(Methacrylamido)propyl]trimethyl‐ammonium chloride (MAPTAC) and acrylic acid (AAc) were used as the ionic comonomer in the hydrogel preparation. Three sets of hydrogels containing 70 mol% AAm and 30 mol% ionic comonomers of varying mole ratios were prepared. The variations of the hydrogel volume in response to changes in pH, and salt concentration were measured. As pH increases from 1, the hydrogel volume V _eq in water first increases and reaches a maximum value at a certain pH. Then, it decreases again with a further increase in pH and attains a minimum value around the isoelectric point (IEP). After passing the collapsed plateau region, the gel reswells again up to pH=7.1. The reswelling of the collapsed gels containing 10 and 4% MAPTAC occurs as a first‐order phase transition at pH=5.85 and 4.35, respectively, while the hydrogel with 1% MAPTAC reswells continuously beyond its IEP. Depending on pH of the solution, the hydrogels immersed in salt solutions exhibit typical polyelectrolyte or antipolyelectrolye behavior. The experimental swelling data were compared with the predictions of the Flory‐Rehner theory of swelling equilibrium including the ideal Donnan equilibria. It was shown that the equilibrium swelling theory qualitatively predicts the experimental behavior of polyampholyte hydrogels.     

Graphene oxide embedded P(AAm)/PANI cryogel polymer composites for sensor application against pesticide,nitro compound,and organic dyes

Abstract

Graphene oxide (GO) embedded superporous poly(acrylamide) (P(AAm)) cryogel composites (P(AAm)-GO) were prepared and used as conductive sensor materials. For this goal, the GOs flakes within superporous P(AAm) cryogels were reduced in-situ employing hydriodic acid (HI), hydrazine (N₂H₄), and sodium borohydride (NaBH₄) as reducing agents. Amongst all reduced agents\the highest conductivity was observed for HI reduced P(AAm)-GO (P(AAm)-rGO) with 1.7?×?10^?6±9.7?×?10^?8 S.cm^?1. Then again, this P(AAm)-rGO was used for in-situ synthesis of conductive polymers, poly(aniline) (PANI), and poly(pyrrole) (PPy) by using oxidative polymerization technique. The SEM, FT-IR, TGA and conductivity measurements were done for the characterization of prepared cryogel composites. It was found that the conductivity of P(AAm)-rGO increased 70- and 1400-fold with the presence of PANI and PPy, respectively. Furthermore, potential sensor application of P(AAm)-rGO/conductive polymers were tested against herbicides such as paraquat, glyphosphate (G), and a phenolic compound, 4-nitrophenol (4-NP), and some dyes such as methylene blue (MB), methyl orange (MO). Conductivity of P(AAm)-rGO/PANI decreased 5.3 -fold upon reacting with 10?mL 50?ppm G solution. The sensitivity and effect of G amounts were also tested for P(AAm)-rGO/PANI cryogel composite.     

Network structure and swelling–shrinking behaviors of pH‐sensitive poly(acrylamide‐co‐itaconic acid) hydrogels

pH‐sensitive poly(acrylamide‐co‐itaconic acid) [P(AAm/IA)] hydrogels were prepared by radiation induced copolymerization of acrylamide (AAm) and itaconic acid (IA) at various ratios. Swelling and shrinking behaviors of these hydrogels were found greatly dependent on the composition of the hydrogel and pH of the buffer solution. The basic structural parameters of the P(AAm/IA) networks such as the molecular weight between crosslinks (M _c) and polymer–solvent interaction parameter (χ) were also determined using the modified Flory‐Rehner equations. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2586–2594, 2004     

Swelling behavior of poly{N‐[3‐(dimethylaminopropyl)] methacrylamide‐co‐acrylamide} hydrogels in aqueous solutions of surfactants

Temperature sensitive poly{N‐[3‐(dimethylaminopropyl)]methacrylamide‐co‐acrylamide} [P(DMAPMA‐co‐AAm)] hydrogels were prepared by the free‐radical crosslinking copolymerization of corresponding monomers in water with N,N‐methylenebisacrylamide as the crosslinker, ammonium persulfate as the initiator, and N,N,N′,N′‐tetramethylethylenediamine as the activator. The swelling equilibrium of the P(DMAPMA‐co‐AAm) hydrogels was investigated as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate and the cationic surfactant dodecyltrimethylammonium bromide. In pure water, regardless of the amount of N,N‐methylenebisacrylamide, the P(DMAPMA‐co‐AAm) hydrogels showed a discontinuous phase transition between 30 and 36 °C. However, the transition temperature changed from discontinuous to continuous with the addition of surfactants; this was ascribed to the conversion of nonionic P(DMAPMA‐co‐AAm) hydrogels into polyelectrolyte hydrogels due to the binding of surfactants through hydrophobic interactions. Additionally, the concentrations of free sodium dodecyl sulfate and dodecyltrimethylammonium bromide ions were measured at different temperatures by conductometry, and it was found that the electric conductivity of the P(DMAPMA‐co‐AAm)–surfactant systems depended strongly on the swelling ratio; most notably, it changed drastically near the phase‐transition temperature of the P(DMAPMA‐co‐AAm) hydrogel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1645–1652, 2006     

Dye removal by a novel hydrogel‐clay nanocomposite with enhanced swelling properties

Acrylamide (AAm)‐2‐acrylamide‐2‐methylpropanesulfonic acid sodium salt (AMPSNa) hydrogel and AAm‐AMPSNa/clay hydrogel nanocomposite having 10 w% clay was prepared by in situ copolymerization in aqueous solution in the presence of a crosslinking agent (N,N′‐methylenebisacrylamide (NMBA)). Swelling properties and kinetics of the hydrogel samples were investigated in water and aqueous solutions of the Safranine‐T (ST) and Brilliant Cresyl Blue (BCB) dyes. The swelling and diffusion parameters were also calculated in water and dye solutions. It was observed that the AAm‐AMPSNa/clay hydrogel nanocomposite exhibits improved swelling capacity compared with the AAm‐AMPSNa hydrogel. It was also found that the diffusion mechanisms show non‐Fickian character. Adsorption properties of the hydrogel samples in the aqueous solution of ST and BCB dyes were also investigated. Clay incorporation into the hydrogel structure increased not only the adsorption capacity but also the adsorption rate. Adsorption capacity values of the hydrogel nanocomposite were found to be 484.2 and 494.2 mg g^?1 for the ST and BCB dyes, respectively. It was seen that the adsorption of dyes by the hydrogel nanocomposite completed in 10 min while the AAm‐AMPSNa hydrogel adsorbed dyes approximately in 90 min. Adsorption data of the samples were modelled by the pseudo‐first‐order and pseudo‐second‐order kinetic equations in order to investigate dye adsorption mechanism. It was found that the adsorption kinetics of hydrogel nanocomposite followed a pseudo‐second‐order model. Equilibrium isotherms were analyzed using the Langmuir and Freundlich isotherms. It was seen that the Langmuir model fits the adsorption data better than the Freundlich model. Copyright © 2008 John Wiley & Sons, Ltd.     

Modeling of absorption kinetics of poly(acrylamide) hydrogels crosslinked by EGDMA and PEGDMAs

In this study, acrylamide-based hydrogels are synthesized by free radical solution polymerization in aqueous solution using ethylene glycol dimethacrylate (EGDMA) and its derivative polyethylene glycol dimethacrylate (PEGDMA) with different molecular weights as crosslinkers in the solution medium. The Fourier transform infrared spectroscopy technique is used for the structural characterization of the hydrogels. Dynamic swelling tests are conducted on acrylamide-based hydrogels for the determination of the swelling characteristics with respect to different crosslinking concentrations at room temperature. The parameters of swelling kinetics and diffusion mechanisms of the hydrogels are calculated with the aid of the data obtained. Accordingly, PEGDMA and EGDMA absorption capacity is found to increase with increasing concentrations. The lowest and highest water absorption capacities in PEGDMA₈₁₀ and EGDMA crosslinked hydrogels are 22.73–48.39 and 10.15–16.02 g/g, respectively. Water intake of hydrogels crosslinked by EGDMA and PEGDMAs followed Fickian nature type diffusion except for PEGDM₈₁₀, which has a swelling exponent greater than 0.5 and so does not follow a Fickian type of diffusion. PEGDM₈₁₀ showed the fastest diffusion rate of between 5.87 × 10^?4 and 10.87 × 10^?4 cm² s^?1.     

Kinetics of the Copolymerization of Methyl Vinyl Ketone and Acrylamide Initiated by the Adduct of Methyl Vinyl Ketone and Imidazole

N-(Butyl-3-one)imidazole acts as an initiating adduct which is formed in the anionic polymerization of methyl vinyl ketone (MVK) induced by imidazole (Im) and is directly formed from Im and the MVK monomer. The kinetics of the anionic homopolymerization of MVK and acrylamide (AAm) under argon in the presence of the adduct were investigated in tetrahydrofuran (THF). The rate of polymerization for the MVK system is expressed as R_p = k[Adduct] [MVK], where k = 3.1 × 10^?6 L/(mol·s)in THF at 30°C. The overall activation energy, E_a , was found to be 5.34 kcal/mol. The R_p for the AAm system is expressed as R_p = k[Adduct] [AAm], where k = 6.8 × 10^?6 L/(mol·s) in THF at 30°C, with E_a 7.78 kcal/mol. The mechanism of the polymerization induced by the initiator adduct is discussed on the basis of these results.