Preparation,Morphology and Properties of Poly(Trimethylene Terephthalate)/Thermoplastic Polyester Elastomer Blends

Poly(trimethylene terephthalate)(PTT)/thermoplastic polyester elastomer (TPEE) blends were prepared and their miscibility, crystallization and melting behaviors, phase morphology, dynamic mechanical behavior, rheology behavior, spherulites morphology, and mechanical properties were investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), parallel-plate rotational rheometry, polarized optical microscopy (POM), wide angle X-ray diffraction (WAXD), universal tensile tester and impact tester, respectively. The results suggested that PTT and TPEE were partially miscible in the amorphous state, the TPEE rich phase was dispersed uniformly in the solid matrix with a size smaller than 2 μm, and the glass transition temperatures of the blends decreased with increasing TPEE content. The TPEE component had a good effect on toughening the PTT without depressing the tensile strength. The blends had improved melt viscosities for processing. When the blends crystallized from the melt state, the onset crystallization temperature decreased, but they had a faster crystallization rate at low temperatures. All the blends’ melts exhibited a predominantly viscous behavior rather than an elastic behavior, but the melt elasticity increased with increasing TPEE content. When the blends crystallized from the melt, the PTT component could form spherulites but their morphology was imperfect with a small size. The blends had larger storage moduli at low temperatures than that of pure PTT.     

Relationship between Microstructure and Mechanical Properties of Ethylene-Octene Copolymer Reinforced and Toughened PP

Polypropylene (PP)/ethylene-octene copolymer (POE) blends with 10–50wt% POE composition were prepared using a twin-screw extruder in the melt state. Mechanical properties of PP and PP/POE blends were tested and the effect of POE content on the crystalline morphology and structure, melting and crystallization behavior, compatiblilty, phase morphology, and the interface cohesiveness of the blends were investigated by polarizing optical microscope (POM), wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and scanning electron microscopy (SEM). The relationship between mechanical properties and microstructure of the PP/POE blends is discussed. The results showed that POE had a dual function of both reinforcing and toughening PP in the range from 10–40wt%, which was attributed to the integrated functions of the degree of crystallinity of the PP phase, phase morphology, and interface cohesiveness of the blend.     

Miscibility,Morphology, and Thermal Properties of Poly(Trimethylene Terephthalate)/Polycarbonate

Abstract

Poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends were prepared by melt blending and rapid quenching in ice water. The miscibility and thermal properties were investigated using differential scanning calorimeter (DSC) and dynamic mechanical analysis (DMA). The blend's morphologies were investigated using scanning and transmission electron microscopies. Both DSC and DMA results suggested that PTT and PC were very limited, partially miscible pairs. The melting point, melt crystallization, and cold crystallization exotherms in the blends of PTT were depressed by the presence and amount of PC. When the PC content was <50 wt%, PC spherical particles were found to distribute evenly in the PTT matrix; at 50–60 wt%, the two‐phase structures were close to being bicontinuous. At higher PC content, PTT formed a string‐like texture in the PC matrix. The PTT spherulitic morphologies in PTT/PC blends were found to be very sensitive to PC and PC content. When the PC content was ≥60 wt%, the blends crystallized as an agglomeration of tiny PTT crystals.     

Mechanical Properties and Crystallization Behavior of Polycarbonate/Polypropylene Blends

The mechanical properties, morphology, and crystallization behavior of polycarbonate (PC)/polypropylene (PP) blends, with and without compatibilizer, were studied by tensile and impact tests, scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The tensile and impact strengths of PC/PP blends decreased with increasing the PP content due to poor compatibility between the two phases. But the addition of compatibilizer improved the mechanical properties of the PC/PP blends, and the maximum value of the mechanical properties, such as tensile and impact strengths of PC/PP (80/20 wt%) blends, were obtained when the compatibilizer was used at the amount of 4 phr. The SEM indicated that the compatibility and interfacial adhesion between PC and PP phases were enhanced. DSC results that showed the crystallization and melting peak temperatures of PP increased with the increase of the PP content, which indicated that the amorphous PC affected the crystallization behavior. However, both the PC and compatibilizer had little effect on the crystallinity of PP in PC/PP blends based on both the DSC and XRD patterns.     

Reactive Compatibilization of Poly(trimethylene terephthalate)/Polypropylene Blends by Polypropylene‐graft‐Maleic Anhydride. Part 1. Rheology,Morphology, Melting,and Mechanical Properties

Poly(trimethylene terephthalate)/polypropylene (PTT/PP) blends were prepared by melt blending. The rheology, morphology, melting, and mechanical properties of PTT/PP blends were investigated with and without the addition of polypropylene‐graft‐maleic anhydride (PP‐g‐MAH). The melt viscosity results showed that the fluid behavior of PTT/PP blends exhibited great disparity to that of PTT but similar to that of PP; the dispersed flexible PP phase in the blends served as a “ball bearing effect” under shear stress, which made the fluid resistance markedly reduced; by contrast, the relatively rigid PTT dispersed phase made only a small contribution to the viscosity. With 5 wt.% PP‐g‐MAH addition during melt processing, both the shear viscosity and the non‐Newtonian index of 70/30 PTT/PP blend were increased over that of the corresponding uncompatibilized one, whereas the shear viscosity of the 30/70 PTT/PP melt decreased slightly indicating that a considerable amount of PP‐g‐MAH did not act as compatibilizer but probably served as plasticizer.

With the increasing of the other component, the melting temperature of the PTT phase showed a slight decrease while the melting temperature of the PP phase showed a slight increase. 5 wt.% PP‐g‐MAH addition had little influence on the melting temperatures of the two components. When PP≤20 wt.%, the cold crystallization temperature of the PTT phase (T_cc (PTT‐phase)) showed little change with the composition; however, it shifted to higher temperature when PP≥30 wt.%. The variations of the T_cc (PTT‐phase), with and without PP‐g‐MAH, suggested that, when PTT was a minor component, the excess PP‐g‐MAH which did not act as compatibilizer might serve as a plasticizer that made the PTT's cold crystallization process to be easier. The SEM results indicated that, for the uncompatibilized blends, the interfaces from particles pulling‐out are clear and smooth, while, for compatibilized blends, the reactive products are at the interfaces. The mechanical properties suggested that PP‐g‐MAH did not result in significant improvement of the toughness of the blend, but the tensile strength increased markedly.     

Rheological,thermal, and mechanical properties of poly(ethylene naphthalate)/poly(ethylene terephthalate) blends

Structural, Theological, thermal, and mechanical properties of blends of poly(ethylene naphthalate) (PEN) and poly(ethylene terephthalate) (PET) obtained by melt blending were investigated using capillary rheometry, differential scanning calorimetry (DSC), scanning electron microscopic (SEM) observation, tensile testing. X-ray diffraction, and ¹H nuclear magnetic resonance (NMR) measurements. The melt Theological behavior of the PEN/PET blends was very similar to that of the two parent polymers. The melt viscosity of the blends was between that of PEN and that of PET. Thermal properties and NMR measurement of the blends revealed that PEN is partially miscible with PET in the as molded blends, indicating that an interchange reaction occurs to some extent on melt processing. The blend of 50/50 PEN/PET was more difficult to crystallize compared with blends of other PEN/PET ratios. The blends, once melted during DSC measurements, almost never showed cold crystallization and subsequent melting and definitely exhibited a single glass transition temperature between those of PEN and PET during a reheating run. Improvement of the miscibility between PEN and PET with melting is mostly due to an increase in transesterification. The tensile modulus of the PEN/PET blend strands had a low value, reflecting amorphous structures of the blends, while tensile strength at the yield point increased linearly with increasing PEN content.     

Miscibility and Isothermal Crystallization Behavior of Poly (Butylene Succinate-co-Adipate) (PBSA)/Poly (Trimethylene Carbonate) (PTMC) Blends

Poly(butylene succinate-co-adipate) (PBSA)/poly (trimethylene carbonate) (PTMC) blend samples with different weight ratios were prepared by solution blending. The morphologies after isothermal crystallization and in the melt were observed by optical microscopy (OM). Differential scanning calorimetry (DSC) was used to characterize the isothermal crystallization kinetics and melting behaviors. According to the OM image before and after melting, it was found that the blends formed heterogenous morphologies. When the PTMC content was low (20%), PBSA formed the continuous phase, while when the PTMC contents was high (40%), PBSA formed the dispersed phase. The glass transition temperatures (T_g) of the blends were determined by DSC and the differences of the T_g values were smaller than the difference between those of pure PBSA and PTMC. In addition, the equilibrium melting points were depressed in the blends. According to these results, the PBSA/PTMC blends were determined as being partially miscible blends. The crystallization kinetics was investigated according to the Avrami equation. It was found that the incorporation of PTMC did not change the crystallization mechanism of PBSA. However, the crystallization rate decreased with the increase of PTMC contents. The change of crystallization kinetics is related with the existences of amorphous PTMC, the partial miscibility between PLLA and PTMC, and the changes of phase structures.     

Studies on compatibilization of polypropylene/thermoplastic polyurethane blends and mechanism of compatibilization

This paper reports a study of compatibilization and the mechanism of compatibilization of polypropylene (PP)/thermoplastic polyurethane (TPU) blends with maleated polypropylene (PP-MA) and its graft copolymer with polyethylene oxide (PEO), (PP-MA)-g-PEO. The results of scanning electron microscope (SEM) and dynamic mechanical analysis showed that (PP-MA)-g-PEO was a very good compatibilizer for PP/TPU blends, while PP-MA also produced some compatibilization. The cocrystallization between bulk PP and PP segments of the compatibilizers was evidenced by differential scanning calorimetry studies. The specific interaction between TPU and polar parts of the compatibilizers was studied with Fourier transform infrared spectroscopy.     

A Study on Properties of Poly(vinyl chloride)/Poly(α-methylstyrene-acrylonitrile) Binary Blends

Blends of poly(vinyl chloride) (PVC) and poly(α-methylstyrene-acrylonitrile) (α-MSAN) with variable composition of 0 to 100 wt% were prepared by melt mixing. Properties of binary blends were extensively studied by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), heat distortion temperature (HDT), mechanical properties, melt flow rate (MFR), and scanning electron microscope (SEM). A single glass transition temperature (T_g ) was observed by DSC and DMTA, indicating miscibility between PVC and α-MSAN. The results of ATR-FTIR indicated that specific strong interactions were not present in the blends and the miscibility was due to interaction between –CN and PVC. With increasing amount of α-MSAN, considerable increase occurred in HDT, flexural strength, and flexural modulus compared with reverse s-shaped decrease in impact strength and elongation at break. Synergism was observed in tensile strength and MFR. No phase separation was observed in SEM photographs, indicating miscibility between PVC and α-MSAN. In addition, morphology of the impact-fractured surfaces, including roughness and non-fused particles, correlated well with the mechanical properties and MFR.     

Assessment of Compatibility in Polypropylene/Poly(lactic acid)/Ethylene Vinyl Alcohol Ternary Blends: Relating Experiments and Molecular Dynamics Simulation Results

Two systems of polypropylene (PP), poly(lactic acid) (PLA) and ethylene vinyl alcohol copolymer (EVOH) ternary blends having different compositions were extruded in a co-rotating twin screw extruder. The first system was PP/PLA (75/25) with various EVOH contents, the second one was PP/EVOH (75/25) having various PLA contents. The effects of composition on the morphology and the tensile and impact properties of the blends were investigated. There were increases in the tensile modulus and tensile strength with an increase in the EVOH and PLA contents in the first and second systems, respectively. A molecular dynamics (MD) simulation was used to investigate the compatibility between the components. Prediction of the miscibility of the blends was carried out by determining the interaction parameters (χ), mixing energies (ΔH_mix), phase diagrams and Gibbs free energies. The MD simulation showed a UCST behavior for the components. Moreover, the simulation results showed a compatibilizer effect for the EVOH component. The experimental values of the dynamic mechanical thermal analysis (DMTA) and mechanical properties were correlated to the MD results. There was a good correlation between the MD and DMTA results. The modulus values using the parallel and Davis models were near to the experimental ones. A good fitting to the mixture law with addition of EVOH confirmed a good compatibilzing effect of it between the PP and PLA components.     

Isothermal Crystallization and Miscibility of Isotactic Polypropylene/Poly(cis-butadiene) Rubber Blends

Isotactic polypropylene/poly(cis-butadiene) rubber (iPP/PcBR) blends were prepared by melt mixing. Isothermal crystallization and miscibility for neat iPP and blends of iPP/PcBR were investigated by differential scanning calorimetry. The presence of PcBR remarkably affected isothermal crystalline behaviors of iPP. An addition of PcBR caused shorter crystallization time and a faster overall crystallization rate, meaning a heterogeneous nucleation effect of PcBR upon crystallization of iPP. For the same sample, the crystallization peak was broader and the supercooling decreased as the crystallization temperature increased. The Avrami equation was suitable to describe the primary isothermal crystallization process of iPP and blends. The addition of PcBR led to an increase of values of the Avrami exponent n, which we suggest was because the blends had a stronger trend of instantaneous three-dimensional growth than neat iPP. The equilibrium melting point depression of the blends was observed, indicating that the blends were partly miscible in the melt.     

Miscibility Determination in Poly(ε-caprolactone)/Poly(Vinyl Formal) Blend by Equilibrium Melting Temperature and Spherulite Morphology

Miscibility of poly(ε-caprolactone), (PCL), containing 1, 5, and 10 wt.% poly(vinyl formal) (PVF) blends was investigated by polarized optical microscopy (POM), atomic force microscopy (AFM), and differential scanning calorimetry (DSC) for spherulitic morphology and equilibrium melting temperature (T°_m, via Hoffman-Weeks plot). The T°_m of PCL in the blends was similar to that of pure PCL, indicating immiscibility. Isothermally, melt crystallized virgin PCL between 30°C and 50°C showed spherulitic morphology with negative birefringence, Maltese cross, and without extinction rings. The nucleation and growth rates of PCL spherulites were found to be dramatically reduced with the addition of PVF. Extinction rings and a change in the sign of the birefringence of the PCL spherulites were observed and were found to be dependent on blend composition and crystallization temperature. The presence of a ring pattern in spherulites was an indication of miscibility between the two polymers that had failed to be detected by thermal methods. The formation of a ring pattern is discussed in terms of lamella twisting originating from a change in the crystallization mechanism.     

Influence of Blend Composition on Crystallization of Poly(L-Lactic Acid)/Poly (Ethylene Oxide) Crystalline/Crystalline Blends

The effect of blend composition on crystallization morphology and behavior of a crystalline/crystalline blend, poly(l-lactic acid) (PLLA)/poly(ethylene oxide) (PEO), during slow, non-isothermal crystallization was studied by polarized light microscopy (PLM) connected with a hot-stage and differential scanning calorimetry (DSC). The results showed that all of the PLLA/PEO blends produced spherulites which gradually became bigger and looser, as well as coarser, with the increment of the PEO content, indicating that the PEO crystals was resided in the interlamellar or interfibrillar (between clusters of commonly oriented lamellae) regions of the PLLA spherulites. In the (25/75) and (10/90) blends, the nucleation and growth processes of the PEO spherulites could be clearly observed in the pre-existing PLLA spherulites. The onset crystallization temperature and the melting point of one component decreased with increasing the content of the other one owing to the good miscibility of the two components in the non-crystalline state and the interaction between their macromolecules, indicating that the crystallization of each component was influenced by the other one.     

Reactive Compatibilization of Poly(trimethylene terephthalate)/Polypropylene Blends by Polypropylene‐graft‐Maleic Anhydride. Part 2. Crystallization Behavior

The crystallization behavior of uncompatibilized and reactive compatibilized poly(trimethylene terephthalate)/polypropylene (PTT/PP) blends was investigated. In both blends, PTT and PP crystallization rates were accelerated by the presence of each other, especially at low concentrations. When PP content in the uncompatibilized blends was increased to 50–60 wt%, PTT showed fractionated crystallization; a small PTT crystallization exotherm appeared at ～135°C besides the normal ～175°C exotherm. Above 70 wt% PP, PTT crystallization exotherms disappeared. In contrast, PP in the blends showed crystallization exotherms at 113–121°C for all compositions. When a maleic anhydride‐grafted PP (PP‐g‐MAH) was added as a reactive compatibilizer, the crystallization temperatures (T _c ) of PTT and PP shifted significantly to lower temperatures. The shift of PTT's T _c was larger than that of the PP, suggesting that addition of the PP‐g‐MAH had a larger effect on PTT's crystallization than on PP due to reaction between maleic anhydride and PTT.

The nonisothermal crystallization kinetics was analyzed by a modified Avrami equation. The results confirmed that PTT's and PP's crystallization was accelerated by the presence of each other and the effect varied with blend compositions. When the PP content increased from 0 to 60 wt%, PTT's Avrami exponent n decreased from 4.35 to 3.01; nucleation changed from a thermal to an athermal mode with three‐dimensional growths. In contrast, when the PTT content increased from 0 to 90 wt% in the blends, changes in PP's n values indicated that nucleation changed from a thermal (0–50 wt% PTT) to athermal (60–70 wt% PTT) mode, and then back to a thermal (80–90 wt% PTT) mode. When PP‐g‐MAH was added as a compatibilizer, the crystallization process shifted considerably to lower temperatures and it took a longer crystallization time to reach a given crystallinity compared to the uncompatibilized blends.     

Influence of halloysite nanotubes (HNTs) on morphology,crystallization, mechanical and thermal behaviour of PP/ABS blends and its composites in presence and absence of dual compatibilizer

Halloysite nanotubes (HNTs) filled 80/20 (wt/wt) polypropylene (PP)/acrylonitrile butadiene styrene (ABS) blends and its composites in presence and absence of dual compatibilizer (polypropylene grafted maleic anhydride (PP-g-MA), and styrene-ethylene, butylene-styrene triblock copolymer grafted with maleic anhydrite (SEBS-g-MA)) have been prepared using twin screw extruder followed by injection moulding. Significant refinements in dispersed ABS droplets diameter and interparticle distance between dispersed ABS droplets were observed in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. This has resulted in significant enhancement in tensile and impact properties of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. Refinement in morphology of dispersed ABS phase results in decrease in crystallinity of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. In addition, HNTs act as heterogeneous nucleating agent for the growth of PP crystals, and hence crystallization rate of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA increases. Thermal stability also increases in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA.     

Compatibilization by Olefin Block Copolymer (OBC) in Polypropylene/Ethylene-Propylene-Diene Terpolymer (PP/EPDM) Blends

The compatibilization by olefin block copolymer (OBC) in the blends of polypropylene (PP)/ethylene-propylene-diene terpolymer (EPDM) and the phase morphology of the ternary blends were investigated by rheology, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) measurements. It was found that the PP/EPDM blends exhibited enhanced mechanical properties in the presence of OBC. The addition of OBC had a significant influence on the phase separation behavior of the blends. For the PP/EPDM-50/50 heterogeneous blends, the addition of 15 phr OBC enabled the two-phase morphology to change from a droplet-matrix structure to a co-continuous one. In the temperature range of 150 to 200 °C, OBC was shown to have a better compatibility with PP than EPDM. The changes in viscosity ratio of the dispersed phase to matrix phase caused by adding OBC might be the dominant factor in controlling the coalescence of the dispersed phase domains. For the crystallization behavior of PP/EPDM/OBC ternary blends, OBC was found to have an induction effect on the formation of β-crystals of PP that was not proportional to the volume of OBC addition. In addition, DSC results showed that PP could induce the OBC crystallization and improve the crystallization temperature of OBC. The existence of simultaneous crystallization behavior between PP and OBC was also observed. A possible mechanism of phase evolution induced by crystallization was proposed.     

Structure and Properties of In-Situ Reactive Compatibilized Polypropylene/Poly (Butyl Methacrylate-Co-Hydroxyethyl Methacrylate) Blend Fibers

In this study, in-situ compatibilized polymer blends of polypropylene (PP) and poly (butyl methacrylate-co-hydroxyethyl methacrylate) P(BMA-co-HEMA) were prepared in a corotating twin screw extruder through the reactive extrusion of mixtures of PP, P(BMA-co-HEMA), butyl methacrylate, and benzoyl peroxide. In the process of reactive extrusion, butyl methacrylate and benzoyl peroxide were used as the monomer and the initiator, respectively. Thereafter the polymer blend was made into fibers via melt spinning. The miscibility of PP and P(BMA-co-HEMA) in the blend fibers was investigated using field emission scanning electron microscopy. The absorption percentage of the blend fibers for organic liquids and their remaining ratios after the absorption tests were also determined and used to prove the generation of the third phase. The changes in the fiber morphology during organic liquid absorption were observed using polarized light microscopy. In addition, the effect of the miscibility on the crystal structure and melting characteristic of the blend fibers were analyzed using wide-angle X-ray diffractometry and differential scanning calorimetry. Finally, the thermal stability of the blend fibers that was associated with the miscibility of PP and P(BMA-co-HEMA) in the blend fibers were characterized by using thermogravimetry and dynamic thermomechanical analysis.     

Miscibility, Crystallization, and Rheological Behavior of Solution Casting Poly(3-hydroxybutyrate)/poly(ethylene succinate) Blends Probed by Differential Scanning Calorimetry, Rheology, and Optical Microscope Techniques

应用差示扫描量热、流变及偏光显微镜等方法研究了聚3-羟基丁酸酯/聚丁二酸乙二醇酯(PHB/PES)共混体系的相容性、结晶和流变行为．相图显示该共混体系有两个玻璃化转变,但PHB的熔点随其含量的减少而降低,这个结果证明该共混体系是部分相容的,同时应用偏光显微镜观察体系结晶形态的发展证实了这个结论．依赖于结晶温度和组成,PHB和PES能同时结晶,也能分步结晶,且PHB的球晶生长速率随PES含量的增加而增大．对于部分相容的聚合物共混体系,共混组成对球晶生长速率的影响也做了详细地讨论．     

Confined Crystallization in Polymer Blends: DSC Studies of the Behavior and Kinetics of Isothermal Crystallization of Polypropylene in Poly(cis-butadiene) Rubber Blends

Thermal properties of polypropylene with poly(cis-butadiene) rubber (iPP/PcBR) blends have been measured by differential scanning calorimetry (DSC), and the melting point T_m, crystallization temperature T_c, enthalpy Δ H (melting enthalpies and crystalline enthalpies), and equilibrium melting point T⁰ _m have been measured and calculated. The variation of T_m, T_c, Δ H and T⁰ _m with composition in the blends was discussed, showing that an interaction between phases is present in iPP/PcBR blends. The degree of supercooling characterizing the interaction between two phases in the blends and the crystallizability of the blends which bears a relationship to the composition of the blends was discussed. The kinetics of isothermal crystallization of the crystalline phase in iPP/PcBR blends was studied in terms of the Avrami equation, and the Avrami exponent n and velocity constant K were obtained. The Avrami exponent n is between 3 and 2, meaning that iPP has a thermal nucleation with two dimensional growths. The variation of the Avrami exponent n, velocity constant K, and crystallization rate G bear a relation to the composition of the blends, n increases with increasing content ofPcBR. K also increased with increasing content of PcBR. All of the K for the blends are greater than for pure iPP. The crystallization rate G (t_1/2) depends on the compositions in the blends; all G of the blends are greater than for iPP.     

Crystallization of poly(phenylenesulfide)/amorphous polyamide blends: DSC and microscopic studies

Poly(phenylenesulfide) (PPS) is a high-performance engineering thermoplastic with exceptional thermal and chemical resistance. The results of crystallization behavior of blends of PPS with amorphous polyamide (PA) are presented. The melting and crystallization behavior was studied using differential scanning calorimetry (DSC), and the crystalline morphology was studied using optical microscopy. The results of thermal analysis indicate that the blends exhibit composition-dependent melting point depression. Optical microscopy studies showed the uniform distribution of amorphous nylon in PPS spherulites. The presence of amorphous nylon enhanced the growth rate compared to that for the neat polymer. The observed changes in the equilibrium melting point crystallization behavior, and spherulitic growth rate are explained.