Effect of the Nature of Crosslinking Agent on the Catalase‐Like Activity of Polystyrene‐Bound Glycine–Metal Complexes

Abstract

Catalase‐like activity of metal complexes of various crosslinked polystyrene‐supported glycines were carried out and correlated with the nature of crosslinking agent in the polymer support. Polystyrenes with 2 mol% divinyl benzene (DVB), ethylene glycol dimethacrylate (EGDMA), and 1,6‐hexanediol diacrylate (HDODA) crosslinking were used as polymer supports. Glycine functions were incorporated to the chloromethylpolystyrenes by polymer analogues reactions and complexed with Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), and Zn(II) ions. The metal uptake varied in the order: Cu(II) > Cr(III) > Mn(II) > Co(II) > Fe(III) > Ni(II) > Zn(II), and extent of metal uptake by various crosslinked systems varied with the nature of crosslinking agent. The polymeric ligands and the metal complexes were characterized by various analytical techniques. The catalytic activities of these metal complexes were investigated towards the decomposition of hydrogen peroxide and was found to decrease in the order: Co(II) > Cu(II) > Ni(II) > Cr(III) > Fe(III) > Mn(II) > Zn(II). With increasing rigidity of the crosslinking agent the catalytic activity also decreased.     

Investigation on the Performance of Supported Molybdenum Carbide for the Partial Oxidation of Methane

The performance of uspported and unsupported molybdenum carbide for the partial oxidation of methane (POM) to syngas was investgated.An evaluation of the catalysts indicates that bulk molybdenum carbied has a higher methane conversion during the initial stage but a lower selectivity to CO and H2/CO ratio in the products.The rapid deactivation of the catalyst is also a significant problem.However,the supported molybdenum carbide catalyst shows a much higher methane conversion,increased selectivity and significantly improved catalytic stability.The characterization by XRD and BET specific area measurements depict an improved dispersion of molybdenum carbide when using alumina as a carrier.The bulk or the supported molybdenum carbide exists in the β-Mo2C phase,while it is transformed into molybdenum dioxide postcatalysis which is an improtant cause of molybdenum carbide deactivation.     

Studies on the Phase Behavior of Beta‐cypermethrion Microemulsion

The phase behavior of the system of surfactant SAA [0203B, nonionic surfactant 700# and methanol (weight ratio=6∶1∶1)]/mixed oil [beta‐cypermethrion, dimethyl benzene and cyclohexanone (weight ratio=2∶2∶1,or 0∶2∶1)]/water [distilled water (0 mg/L), or standard water (342 mg/L), or ultra‐hard water (500 mg/L)] has been studied in a pseudoternary phase diagram at 25 ± 1°C. Our results indicated that the isotropic monophasic area in the phase diagrams decreased significantly as the beta‐cypermethrion was added in the oil phase. In an attempt to the microemulsion electrical condectivity can be define regions corresponding to three structure states W/O, B.C., and O/W type in the microemulsion domain. The influence of beta‐cypermethrion on their regions sequences B.C. > O/W?W/O type. This work will be beneficial to improving the quality of beta‐cypermethrion microemulsion and make it more competitive in the market.     

Effect of Catalyst Pretreatment on the Oxidation of Carbon Monoxide over Gold Catalysts Supported on Double Oxides

ＥｆｅｃｔｏｆＣａｔａｌｙｓｔＰｒｅｔｒｅａｔｍｅｎｔｏｎｔｈｅＯｘｉｄａｔｉｏｎｏｆＣａｒｂｏｎＭｏｎｏｘｉｄｅｏｖｅｒＧｏｌｄＣａｔａｌｙｓｔｓＳｕｐｐｏｒｔｅｄｏｎＤｏｕｂｌｅＯｘｉｄｅｓＨＡＯＺｈｅｎｇｐｉｎｇＡＮＬｉｄｕｎ１）ＷＡＮＧＨｏｎ...     

Studies on the Performance and Structure of Supported Catalysts for the Partial Oxidation of Methane to Syngas

The catalytic properties of several supported metal catalysts on different carriers were studied in the partial oxidation of methane (POM) to syngas. In our experiment, supported noble metal catalysts exhibited better performance than the other supported transition metal catalysts. The catalyst performances were significantly influenced by the d-electron configuration of the active metal components and the dispersion of active metal components on the support. A catalyst with a moderate number of unpaired electrons in the d-orbital of the active metal support without obvious acidity or redox activity (e.g. MgO) was suitable for POM performance. The Rh/SiO2 catalyst was the best in the POM reaction, among those investigated. Reaction conditions apparently also affected the POM performance of the catalyst. The conversion of methane and the selectivity for CO increased with the reaction temperature, and a high CH4/O2 ratio was not beneficial for POM performance.     

Thermal Behavior of Syndiotactic Polystyrene/1,2‐Dichloroethane Gels and Stoichiometry of Polymer‐Solvent Compounds

Abstract

The phase behavior of syndiotactic polystyrene (sPS)/1,2‐dichloroethane (DCE) gels has been investigated by differential scanning calorimetry (DSC) and wide angle x‐ray diffraction (WAXD) for different gel formation conditions. DSC data show that the gel melting temperatures are independent of the cooling conditions leading to gel formation, whereas the melting enthalpies of the gels depend on the cooling history. WAXD measurements show that for low concentration gels the sPS/DCE clathrate structure is obtained, whereas for high concentration gels both the clathrate structure and the solvent‐free β phase can be obtained. Furthermore, the onset of formation of the β phase is dependent on the cooling rate. In light of combined DSC and WAXD data, the reliability of the DSC in evaluating the absolute stoichiometry of polymer‐solvent compounds formed in sPS/DCE gels is discussed.     

Silica Chromate as a Novel Oxidizing Agent for the Oxidation of 1,4‐Dihydropyridines

Silica chromate easily converts 1,4‐dihydropyridines to their corresponding pyridines in the presence of NaHSO₄ · H₂O and wet SiO₂ in dichloromethane at room temperature in good to excellent yields.     

Oxidation of Aldehydes and Ketones into Carboxylic Acids and Esters Using 4‐Amino‐2‐Chloroperbenzoic Acid Supported on Silica Gel

Abstract

4‐Amino‐2‐chloroperbenzoic acid supported on silica gel was found to be a versatile and efficient oxidant for the oxidation of aldehydes and ketones to the corresponding carboxylic acids and esters.     

Large‐scale Experimental Study on the Effects of Flooring Materials on Combustion Behavior of Thermoplastics

The effects of flooring materials on the combustion behavior of thermoplastics is investigated. Based on the ISO 9705 fire test setup, an experimental rig was designed. Full‐scale experiments of PP combustion were carried out using five flooring boards, namely gypsum, steel, wood, ceramic tile and PVC. The experimental results indicate that the flooring boards play an important role in the heat release rates of typical thermoplastics combustion. Specifically, the time for the sharp increase of heat release rate is generally later for the flooring boards with larger thermal conductivity, except for the case of PVC. Preliminary analyses suggest that the reason for the exception of PVC is the expansion and carbonization of PVC at high temperature. In addition, experimental results also show that the corresponding peak heat release rate of thermoplastics combustion would be generally smaller for the flooring board with a larger thermal mass, except for the case of gypsum. The primary cause for the exception of gypsum may be the heat absorption by the crystal water released from the gypsum during the burning of hot pool oil.     

NMR Investigation of the Influence of Sulfate Groups at C‐2 and C‐4 on the Conformational Behavior of Fucoidan Fragments with Homo‐(1→3)‐Linked Backbone#

The conformational behavior of 2‐O‐ and 4‐O‐sulfated derivatives of linear (1→3)‐linked di‐, tri‐, and tetrafucosides and 2,3‐branched tetrafucoside was studied by means of theoretical molecular modeling and experimental determination of trans‐glycosidic vicinal coupling constants ³J_C,H. It was shown that O‐sulfation of (1→3)‐linked oligofucosides restricts their conformational flexibility and changes the conformational equilibrium if compared with the parent nonsulfated oligosaccharides. In the case of 2‐O‐sulfated oligofucosides, the conformations of O‐glycoside linkages depend on its location within the oligosaccharide chain and the chain length as well as on the presence of a 2,3‐branch, whereas the conformation of the (1→3)‐linkage in the presence of a 4‐O‐sulfate group only depends on the presence of a 2,3‐branch.     

An Electrorheological Study on the Behavior of Water‐in‐Crude Oil Emulsions Under Influence of a DC Electric Field and Different Flow Conditions

The influence of an applied DC electric field on viscosity and droplet size distribution of different water‐in‐crude oil emulsions was monitored in order to investigate the induction of coalescence of the water droplets. The effects caused by the voltage imposition were studied by rheological analysis and the validity of the obtained results was discussed, comparing with the features of real electrocoalcscer systems. A low field NMR technique (CPMG NMR) and digital video microscopy (DVM) were used to elucidate the behavior of the emulsions. Experiments performed at low shear rate with increasing electric field magnitude showed an increase in viscosity until a critical value. E_CRIT was reached. Thereafter coalescence occurred and viscosity decreased irreversibly below its initial value. The electrorheological behavior of the emulsions can be attributed to the organization (flocculation) of water droplets induced by the electric field, accompanied by an increase in viscosity. The structure breaks down as the shear rate is increased, leading to a decrease in viscosity. Experiments performed at high shear showed only a small decline in the viscosity. Although it was evident that coalescence took place, it did not involve the whole sample, because the electrodes were uncoated. As a direct consequence, the mean value of the droplet size within the emulsion did not change noticeably. Nonetheless this mean value was less recurrent and the formation of droplets of very large diameter occurred.     

The Use of ATR‐FTIR to Determine the Effects of Functional Groups on Interfacial Crosslinking of Reactive Nanoparticles

Abstract

The film formation and crosslinking of complementary reactive nanoparticle blends of acetoacetoxy (or acetoacetamido) functional particles with isocyanate functional particles were investigated using attenuated total reflectance‐Fourier transform infrared (ATR‐FTIR) spectroscopy. A series of copolymers of 2‐ethylhexyl methacrylate (EHMA) with acetoacetoxy ethyl methacrylate (AA), 2‐methyl‐acrylic acid 2‐methyl‐2‐(3‐oxo‐butyrylamino)‐propyl ester (AM), and dimethyl meta‐isopropenyl benzyl isocyanate (TMI) were prepared by emulsion polymerization techniques at room temperature. These blends were air‐dried on ATR‐FTIR germanium (Ge) discs while the FTIR spectra were taken during the film formation process. The interfacial crosslinking reaction between functional moieties during the film formation process was determined using the FTIR data. The reactivity of acetoacetamido group is higher than that of acetoacetoxy group and the rate constant for the crosslinking reaction between two reaction moieties of terpolymer samples is higher as compared to the blended systems.     

Influence of Carboxylic Acids on the Synthesis of Chlorohydrin Esters from 1,3‐Butanediol

The influence of diverse carboxylic acid on the preparation of chlorohydrin esters using a one‐pot esterification–chlorination reaction, in which one of the reagents (chlorotrimethylsilane) acts as solvent, is described. Whereas the acid with low pKa provided higher amounts of the 2‐chloro regioisomer, the ones with higher pKa rendered the 1‐chloro regioisomer in 80% yield. These results are in accordance with the mechanism proposed in a previous article.     

Influence of Electrolytes on the Thixotropy of Ferric Aluminum Magnesium Hydroxide‐Montmorillonite Suspensions

Abstract

The thixotropy of suspensions consisting of ferric aluminum magnesium hydroxide (Fe‐Al‐Mg‐MMH) and Na‐montmorillonite (MT) is examined with special emphasis on the influence of electrolytes. When NaCl or MgCl₂ is added into the Fe‐Al‐Mg‐MMH/MT suspension, the thixotropy of the suspension may change (if positive) from positive and complex into negative, but NaCl or MgCl₂ can't alter the thixotropic type of a negatively thixotropic suspension. When AlCl₃ was added to positive thixotropic system can be transformed to a complex one, whereas a complex and negative thixotropic suspension remains unchanged, for additions less than 0.01 mol/L; when the addition level of AlCl₃ increases, all types of thixotropic systems are changed to non‐thixotropic. In addition, NaCl and MgCl₂ make the initial viscosity measured after cessation of intensive shearing increase, but the value of the viscosity decreased rapidly with time. The equilibrium viscosity of the suspension decreased gradually with increasing concentrations of NaCl and MgCl₂ in the suspension. With increasing concentration of AlCl₃, the equilibrium viscosities of the positive thixotropic suspension and the complex thixotropic suspension increase at first, but decrease later, and the equilibrium viscosity of negative thixotropic suspensions decrease gradually.     

Dye Binding Characteristics of N,N′‐Methylene‐bis‐acrylamide (NNMBA)‐Crosslinked Polyacrylamide‐Supported Amine and its Photooxidizing Ability

The dye binding characteristics of 8 mol% NNMBA‐crosslinked polyacrylamide‐supported amine is investigated with Rose Bengal (RB), Methyl Orange (MO), Methylene Blue (MB) and Methyl Red (MR). The influence of the concentration of dye solution on dye binding, time course of dye binding and characterization were explored. It is observed that binding is higher in the case of Rose Bengal and dye binding depends on the polarity, as well as the size of the dye molecule. The photooxidation property of polymer bound RB was investigated towards the oxidation of benzoin to benzil. RB bound polymer acts as an efficient heterogenous photooxidizing agent.     

Studies on the Catalytic Properties of Magnesia Supported on γ-Alumina

ＩｎｔｒｏｄｕｃｔｉｏｎＧｌｙｃｏｌｅｔｈｅｒｓａｒｅｉｍｐｏｒｔａｎｔｉｎｄｕｓｔｒｉａｌｄｅｒｉｖａｔｉｖｅｓｏｆｅｐｏｘｉｄｅｓ .Ｐｏｌｙｅｔｈｙｌｅｎｅ ｇｌｙｃｏｌｅｔｈｙｌｅｔｈｅｒｓａｎｄｐｏｌｙｐｒｏｐｙｌｅｎｅｇｌｙｃｏｌｅｔｈｙｌｅｔｈｅｒｓａｒｅｔｗｏｉｍｐｏｒｔａｎｔｓｅｒｉｅｓｏｆｐｒｏｄｕｃｔｓ .Ｇｌｙｃｏｌｅｔｈｅｒｓａｒｅｇｏｏｄｓｏｌｖｅｎｔｓｄｕｅｔｏｔｈｅｐｒｅｓｅｎｃｅｏｆ—Ｏ—ａｎｄ—ＯＨ ｇｒｏｕｐｓ.Ａｓａｒｅ ｓｕｌｔ ,ｔｈｅｙａｒｅｗｉｄｅｌｙｕｓｅ…     

Silica‐Gel‐Supported Ceric Ammonium Nitrate (CAN): A Simple and Efficient Solid‐Supported Reagent for Oxidation of Oxygenated Aromatic Compounds to Quinones

A silica‐gel‐supported heterogeneous ceric ammonium nitrate (CAN) reagent has been developed for oxidizing oxygenated aromatics to quinones in nonaqueous media. The advantages of this procedure include excellent yields, mild reaction conditions, nonaqueous media, short reaction times, and easy product isolation.     

Influence of Cyclodextrin on the Styrene Polymerization

Cyclodextrin (CD) are oligosaccharides consisting of 6(α), 7(β), 8(γ) units of 1,4-linked glucose. Due to their polar hydrophilic outer shell and relatively hydrophobic cavity, they are able to build up host-guest complexes by inclusion of suitable hydrophobic molecules. The formation of these complexes leads to significant changes of the solubility and reactivity of the guest molecules, but without any chemical modification. Thus, water insoluble molecules may become completely water solu…     

Temperature Effect on the Phase Behavior of the Systems Water/Sucrose Laurate/Ethoxylated‐mono‐di‐glyceride/Oil

The phase behavior of the systems water/sucrose laurate/ethoxylated mono‐di‐glyceride/oil was investigated as function of temperature and the weight ratio of EMDG in the mixed surfactants. The oils were R (+)‐limonene, isopropylmyristate, and caprylic‐capric triglyceride. This study demonstrates that the phase inversion temperature (PIT) decreases and the efficiency of the mixed surfactants (γ¯) increase as the weight ratio of the EMDG in the mixed surfactants increases. R (+)‐limonene gave lower phase inversion temperatures and higher efficiencies compared to isopropylmyristate, and caprylic‐capric triglyceride. The solubilization capacity of the system water/sucrose laurate/oil increased upon the addition of ethoxylated mono‐di‐ glyceride which stabilize the surfactant layer and increase the interfacial area.     

Kinetic Spectrophotometric Determination of Traces of Manganese(II) by Its Catalytic Effect on Oxidation of 4‐Hydroxycoumarin with Potassium Permanganate in River Water Samples

Abstract

A new kinetic method for determination of traces of manganese(II) based on its catalytic effect on the oxidation of 4‐hydroxycoumarine with KMnO₄ at pH=1.35 and at a temperature of 25°C was proposed. The reaction was followed spectrophotometrically by measuring the decrease in the absorbance of the dye at 525 nm. The calibration graph is linear in the range 20–200 ng/cm³. The effects of certain foreign ions upon the reaction rate were determined for assessment by the selectivity of the method. The proposed method has been applied for determination of manganese(II) in river water samples with satisfactory results.