Mixed-phase Mesoporous TiO2 Film for High Efficiency Perovskite Solar Cells

Mesoporous scaffold structures have played great roles in halide perovskite solar cells(PSCs),due to the excellent photovoltaic performance and commercial perspective of mesoporous PSCs.Here,we reported a mixed-phase TiO2 mesoporous film as an efficient electron transport layer(ETL)for mesoporous perovskite solar cells.Due to the improved crystal phase,fihn thickness and nanopartMe size of TiO2 layer,which were controlled by varying the one-step hydrothermal reaction time and annealing time,the PSCs exhibited an outstanding short circuit photocurrent density of 25.27 mA/cm^2,and a maximum power conversion efficiency(PCE)of 19.87%.It is found that the ultra-high Jsc attributes to the excellent film quality,light capturing and excellent electron transport ability of mixed-phase TiO2 mesoporous film.The results indicate that mix-phase mesoporous metal oxide fihns could be a promising candidate for producing effective ETLs and high efficiency PSCs.     

SnO2表面卤化提高钙钛矿太阳能电池光伏性能

钙钛矿太阳能电池(PSCs)成为近几年来迅速发展的新型太阳能电池,其中将SnO₂纳米粒子层用作电子传输层(ETL)的钙钛矿太阳能电池器件得到了广泛的关注。SnO₂有着更低的制备温度,使其具备应用于柔性器件的潜力,但与钙钛矿层能级不匹配等问题限制着其发展。而在界面处加入钝化层,尤其是表面卤化的方法或可解决这一问题。本文综合研究了SnO₂表面卤化对钙钛矿太阳能电池光伏性能的影响,选用四丁基氯化铵(TBAC)、四丁基溴化铵(TBAB)和四丁基碘化铵(TBAI)三种钝化材料对SnO₂表面进行钝化处理,并对钝化材料溶液进行了浓度梯度研究。通过材料形貌、结构和光学性能表征以及电池器件性能测试分析等方法,证明了SnO₂表面卤化可提高钙钛矿层的质量和PSCs光伏性能,并从器件内部电荷传输动力学等角度解释了器件性能改善的原因。为进一步说明其性能改善的机理,采用基于密度泛函理论(DFT)的第一性原理计算方法对材料表面性质进行了深入研究,从能量、结构、电荷密度、态密度、功函数等角度解释了表面卤化提高SnO₂/钙钛矿界面处电子传输特性的原因。实验和理论计算均表明TBAC对于SnO₂具有较好的钝化效果,并随着溶液浓度的提升钝化作用越明显。SnO₂表面卤化作用的深入研究不仅对提高电池器件性能具有实际意义,还能够帮助理解太阳能电池界面现象,为界面改性提供新的研究思路。     

低成本富勒烯衍生物电子传输层在钙钛矿太阳能电池的应用

Organic-inorganic hybrid perovskite solar cells (PSCs) have attracted significant attention owing to their high absorption coefficient and ambipolar charge transport properties. With only several years of development, the power conversion efficiency (PCE) has increased from 3.8% to 22.7%. In general, PSCs have two types of structural architecture: mesoporous and planar. The latter possesses higher potential for commercialization due to its simpler structure and fabrication process, especially the inverted planar structure, which possesses negligible hysteresis. In an inverted PSC, the electron transport materials (ETM) are deposited on a perovskite film. Only a few ETMs can be used for inverted PSCs as the perovskite film is easily damaged by the solvent used to dissolve the ETM. Furthermore, the energy levels of the ETM should be well aligned with that of the perovskites. Normally it is difficult to use inorganic ETMs as they require high temperatures for the annealing process to improve the electron conductivity; the perovskite film cannot sustain these high temperatures. To date, the fullerene derivative, [6, 6]-phenyl-C61-butyric acid methyl ester (PCBM), is the most commonly used organic ETM for high efficiency inverted planar PSCs. However, the high manufacturing cost due to its complex synthesis retards the industrialization of the PSCs. Here, we introduce a fullerene pyrrolidine derivative, N-methyl-2-pentyl-[60]fullerene pyrrolidine (NMPFP), synthesized via the Prato reaction of C₆₀ directly with cheap hexanal and sarcosine. Then the NMPFP electron transport layer (ETL) was prepared by a simple solution process. The properties of the resulting NMPFP ETLs were characterized using UV-Vis absorption spectroscopy, cyclic voltammetry measurements, atomic force microscopy, and conductivity test. From the results of the UV-Vis absorption spectroscopy and cyclic voltammetry measurements, the LUMO level of NMPFP ETL was calculated to be 0.2 eV higher than that of the PCBM ETL. This contributes to a higher open-circuit photovoltage. In addition, the NMPFP film presented higher conductivity than the PCBM film. Thus, the photo-generated charge carriers in the perovskite films should be transported more efficiently to the NMPFP electron transport layer (ETL) than to the PCBM ETL. This was confirmed by the results of the steady-state photoluminescence spectroscopy. Finally, the NMPFP as an alternative low-cost ETL was employed in an inverted planar PSC to evaluate the device performance. The device made with the NMPFP ETL yielded an efficiency of 13.83% with negligible hysteresis, which is comparable to the PCBM counterpart devices. Moreover, since stability is another important parameter retarding the commercialization of PSCs, the stability of the PCBM and NMPFP base PSCs were investigated and compared. It was found that the NMPFP devices possessed significantly improved stability due to the higher hydrophobicity of the NMPFP. In conclusion, this research demonstrates that NMPFP is a promising ETL to replace PCBM for the industrialization of cheap, efficient and stable inverted planar PSCs.     

A Rutile TiO2 Electron Transport Layer for the Enhancement of Charge Collection for Efficient Perovskite Solar Cells

Interfacial charge collection efficiency has demonstrated significant effects on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Herein, crystalline phase‐dependent charge collection is investigated by using rutile and anatase TiO₂ electron transport layer (ETL) to fabricate PSCs. The results show that rutile TiO₂ ETL enhances the extraction and transportation of electrons to FTO and reduces the recombination, thanks to its better conductivity and improved interface with the CH₃NH₃PbI₃ (MAPbI₃) layer. Moreover, this may be also attributed to the fact that rutile TiO₂ has better match with perovskite grains, and less trap density. As a result, comparing with anatase TiO₂ ETL, MAPbI₃ PSCs with rutile TiO₂ ETL delivers significantly enhanced performance with a champion PCE of 20.9 % and a large open circuit voltage (V_OC) of 1.17 V.     

紫外光辐照下CH3NH3PbI3基钙钛矿太阳能电池失效机制

随着光伏产业的不断发展,有机无机杂化钙钛矿太阳能电池的研发成为科学与工业界广泛关注的焦点。到目前为止,其光电转换效率已经提高到了25.2%,成为替代硅基太阳能电池的核心方案之一。然而,钙钛矿太阳能电池的稳定性较差,容易受到环境中氧气、水分、温度甚至光照的影响,这严重制约了其大规模推广与应用。大量科学研究表明,如何避免紫外辐照下有机无机杂化钙钛矿太阳能电池的性能衰减,对于提高钙钛矿太阳能电池的光照稳定性至关重要。然而到目前为止,仍然没有系统的工作来对紫外辐照下钙钛矿太阳能电池性能以及微结构演化过程进行详细的表征与分析。本文中,我们利用聚焦离子束-扫描电子显微分析(FIB-SEM)以及球差校正透射电子显微分析(TEM)等技术,全面地研究了紫外辐照过程中有机无机杂化钙钛矿太阳能电池性能变化规律以及电池微结构演化特征。实验结果表明,紫外辐照过程中太阳能电池内部会形成0.5–0.6 V的内建电场,钙钛矿中的I^-离子在电场的驱动下向金属Au电极和空穴传输层2, 2’, 7, 7’-四[N, N-二(4-甲氧基苯基)氨基]-9, 9'-螺二芴(Spiro-OMeTAD)一侧迁移;随后,空穴传输层与金电极的界面处,碘离子与光生空穴一起与金电极发生反应,将金属态Au氧化成离子态Au⁺。而Au⁺离子则在内建电场的驱动下反向迁移穿过钙钛矿MAPbI₃层,直接被SnO₂和MAPbI₃界面处的电子还原形成金属Au纳米团簇。除此之外,紫外辐照过程中钙钛矿太阳能电池性能降低的同时,往往伴随着Spiro-OMeTAD与钙钛矿界面处物质迁移、钙钛矿薄膜内晶界展宽以及Au纳米颗粒周围MAPbI₃物相分解等现象。以上各种因素的协同作用,共同导致了紫外光照下有机无机杂化钙钛矿太阳能电池光电转换性能(PCE)、开路电压(V_oc)以及短路电流(J_sc)等性能参数的急剧下降。     

A mini review: Constructing perovskite p-n homojunction solar cells

Organic metal halide perovskite materials have excellent photoelectric properties, and the power conversion efficiency(PCE) of the perovskite solar cells(PSCs) has increased from 3.8% to more than 25%. In the development of PSCs, innovative architectures were being proposed constantly. However, the use of the electron transport layer(ETL) and hole transport layer(HTL) increases manufacturing costs and process complexity. Perovskite material has ambipolar charge transport characteristics, so it c...     

钙钛矿太阳能电池电子传输层的制备及应用

目前,有机-无机杂化钙钛矿太阳能电池(PSC)的器件效率已经超过25％.电子传输层作为PSC中的重要组成部分在提取和传输光生电子,阻挡空穴,修饰界面,调节界面能级和减少电荷复合等方面起着关键作用.无机n型材料,例如TiO2、ZnO、SnO2和其他金属氧化物材料具有成本低和稳定性好的特点,经常在传统PSC中被用作电子传输...     

Designing a Perylene Diimide/Fullerene Hybrid as Effective Electron Transporting Material in Inverted Perovskite Solar Cells with Enhanced Efficiency and Stability

Electron transport materials (ETM) play an important role in the improvement of efficiency and stability for inverted perovskite solar cells (PSCs). This work reports an efficient ETM, named PDI‐C₆₀, by the combination of perylene diimide (PDI) and fullerene. Compared to the traditional PCBM, this strategy endows PDI‐C₆₀ with slightly shallower energy level and higher electron mobility. As a result, the device based on PDI‐C₆₀ as electron transport layer (ETL) achieves high power conversion efficiency (PCE) of 18.6 %, which is significantly higher than those of the control devices of PCBM (16.6 %) and PDI (13.8 %). The high PCE of the PDI‐C₆₀‐based device can be attributed to the more matching energy level with the perovskite, more efficient charge extraction, transport, and reduced recombination rate. To the best of our knowledge, the PCE of 18.6 % is the highest value in the PSCs using PDI derivatives as ETLs. Moreover, the device with PDI‐C₆₀ as ETL exhibits better device stability due to the stronger hydrophobic properties of PDI‐C₆₀. The strategy using the PDI/fullerene hybrid provides insights for future molecular design of the efficient ETM for the inverted PSCs.     

通过磁控溅射金属钛生长金红石型二氧化钛纳米片阵列应用于钙钛矿太阳能电池

本文首次通过磁控溅射方法,在FTO表面溅射一层Ti金属层,结合水热反应,原位生长TiO₂纳米片阵列（TiO₂ NSAs）. 经过退火处理,Ti金属层转变为致密的TiO₂层,因此基于此方法制得的金红石型TiO₂ NSAs与FTO基底具有很强的结合力. 与通过原子层沉积 (ALD) 以及悬涂 (SC) 法所得的另外两种TiO₂致密层生长的TiO₂ NSAs对比发现,基于本文所述方法制备的TiO₂ NSAs作为支架层的钙钛矿太阳能电池具有最佳性能. 上述结果主要是由于该TiO₂ NSAs无明显缺陷,并且在TiO₂ NSAs/TiO₂致密层/FTO界面接触很好. 值得注意的是,通过优化实验条件,基于此种TiO₂ NSAs的钙钛矿太阳能电池的最高光电转换效率可达11.82%.     

Dual-Interface Engineering in Perovskite Solar Cells with 2D Carbides

Passivating the interfaces between the perovskite and charge transport layers is crucial for enhancing the power conversion efficiency (PCE) and stability in perovskite solar cells (PSCs). Here we report a dual-interface engineering approach to improving the performance of FA_0.85MA_0.15Pb(I_0.95Br_0.05)₃-based PSCs by incorporating Ti₃C₂Cl_x Nano-MXene and o-TB-GDY nanographdiyne (NanoGDY) into the electron transport layer (ETL)/perovskite and perovskite/ hole transport layer (HTL) interfaces, respectively. The dual-interface passivation simultaneously suppresses non-radiative recombination and promotes carrier extraction by forming the Pb−Cl chemical bond and strong coordination of π-electron conjugation with undercoordinated Pb defects. The resulting perovskite film has an ultralong carrier lifetime exceeding 10 μs and an enlarged crystal size exceeding 2.5 μm. A maximum PCE of 24.86 % is realized, with an open-circuit voltage of 1.20 V. Unencapsulated cells retain 92 % of their initial efficiency after 1464 hours in ambient air and 80 % after 1002 hours of thermal stability test at 85 °C.     

Recent advancement in inorganic-organic electron transport layers in perovskite solar cell: current status and future outlook

Organic-inorganic lead halide perovskite solar cells have captured significant attention in recent years due to low processing costs and unprecedented development in power conversion efficiency (PCE). It has appeared from 2009 with PCE of 3.8% to being claimed more than 25.2% PCE in a very short span of time, showing their future prospective toward the fabrication of less expensive and stable solar cells. The incredible advancement in this technology encourages at one end, whereas several hurdles restricting its complete utilization for commercial purposes at another end. Although the selection of perovskite structure is limited with planar and mesoporous electron transport layers (ETLs), but identification of appropriate ETLs necessitates excellent effort to improve the surface morphology of absorber and obtain enhanced PCE with higher stability. In the present review, we have investigated various inorganic-organic ETLs with different device configurations of PSCs, primarily focusing on crystallization and morphology control techniques of ETL thin films. Numerous strategies such as surface functionalization, doping, and addition of interfacial layer are adopted for ETLs, and their effect on device efficiency, performance, and hysteresis is also discussed in detail. Additionally, designs of PSCs with different device configurations are discussed as well, providing future guidelines for significant progress in PSCs structure with different ETLs.     

In-situ fabrication of dual porous titanium dioxide films as anode for carbon cathode based perovskite solar cell

We develop a dual porous(DP) TiO_2 film for the electron transporting layer(ETL) in carbon cathode based perovskite solar cells(C-PSCs). The DP TiO_2 film was synthesized via a facile PS-templated method with the thickness being controlled by the spin-coating speed. It was found that there is an optimum DP TiO_2 film thickness for achieving an effective ETL, a suitable perovskite/TiO_2 interface, an efficient light harvester and thus a high performance C-PSC. In particular, such a DP TiO_2 film can act as a scaffold for complete-filling of the pores with perovskite and for forming high-quality perovskite crystals that are seamlessly interfaced with Ti_O2 to enhance interfacial charge injection. Leveraging the unique advantages of DPTiO2 ETL, together with a dense-packed and pinhole-free TiO_2 compact layer, PCE of the C-PSCs has reached 9.81% with good stability.     

Suppressing Interfacial Charge Recombination in Electron-Transport-Layer-Free Perovskite Solar Cells to Give an Efficiency Exceeding 21 %

The performances of electron-transport-layer (ETL)-free perovskite solar cells (PSCs) are still inferior to ETL-containing devices. This is mainly due to severe interfacial charge recombination occurring at the transparent conducting oxide (TCO)/perovskite interface, where the photo-injected electrons in the TCO can travel back to recombine with holes in the perovskite layer. Herein, we demonstrate for the first time that a non-annealed, insulating, amorphous metal oxyhydroxide, atomic-scale thin interlayer (ca. 3 nm) between the TCO and perovskite facilitates electron tunneling and suppresses the interfacial charge recombination. This largely reduced the interfacial charge recombination loss and achieved a record efficiency of 21.1 % for n-i-p structured ETL-free PSCs, outperforming their ETL-containing metal oxide counterparts (18.7 %), as well as narrowing the efficiency gap with high-efficiency PSCs employing highly crystalline TiO₂ ETLs.     

电泳法制备的致密氧化锡薄膜及其在高稳定性钙钛矿太阳能电池中的应用

在平面型钙钛矿太阳能电池中常采用SnO₂作为电子传输层材料,相应的SnO₂薄膜常采用溶液旋涂法制备。但是由于前驱液中的纳米颗粒可能会发生部分团聚、基底和溶液难以完全避免灰尘等杂质颗粒混入,且最佳的SnO₂电子传输层的厚度通常仅有约20 nm,所以这种方法制备的电子传输层难以保证严格致密和无纳米针孔。在本工作中,我们报道了一种电泳沉积制备致密SnO₂薄膜的方法,并用其有效地提高了钙钛矿太阳能电池的光电转换效率和工况稳定性。通过电泳法,表面带负电荷的SnO₂纳米颗粒在电场的作用下沉积到氧化铟锡(ITO)阳极表面,这种方法得到的薄膜比旋涂法制备的更为致密。将其应用于n-i-p结构的钙钛矿太阳能电池中,能够使得暗电流降低并抑制载流子的非辐射复合,从而提高电池的短路电流和开路电压,进而实现更高的光电转换效率(从18.17%提高到19.52%),且能消除迟滞效应。更重要的是,长期工况稳定性测试表明基于电泳-旋涂法制备的器件在1个太阳的光照下、最大功率点处连续工作960 h后,仍然能够保持71%的初始效率;然而基于旋涂法制备的器件在工作100 h后即降低到初始效率的70%。本工作提供了一种全新的SnO₂电子传输层的制备方法,显著地提高了器件性能和工况稳定性,后续有望应用于制备大面积器件和电池模组。     

SnO2双层电子传输层对钙钛矿太阳能电池界面电荷传输的影响

为了改善基于SnO₂电子传输层的钙钛矿太阳能电池的界面电荷传输特性和迟滞现象,我们采用低温溶液处理工艺制备了4种不同类型的SnO₂电子传输层用于钙钛矿太阳能电池,包括由SnCl₄·5H₂O溶胶-凝胶层(Cl₄-SnO₂)、SnCl₂·2H₂O溶胶-凝胶层(Cl₂-SnO₂)和SnO₂纳米颗粒层(NP-SnO₂)与SnO₂胶体层(Col-SnO₂)两两相互作用形成的同质结SnO₂双层电子传输层和Col-SnO₂单层电子传输层;并系统研究了不同SnO₂双层电子传输层对器件光电性能和迟滞现象的影响。通过扫描电镜(SEM)、X射线衍射(XRD)、稳态光致发光(PL)、电化学阻抗(EIS)和稳定性测试等表征证实,在Col-SnO...     

绝缘氧化物包覆对钙钛矿太阳电池性能及界面电荷复合动力学的影响

采用浸渍法对钙钛矿太阳电池的介孔层TiO₂纳米颗粒进行了SiO₂、ZrO₂、Al₂O₃几种绝缘氧化物包覆,研究了其对电池光伏性能以及界面电荷复合动力学的影响。结果表明, SiO₂包覆之后,电池的填充因子(FF)从67.6%提高到72.3%,光电转换效率提升到13.7%, ZrO₂和Al₂O₃包覆导致电池开路电压提升约50mV,但是短路电流(J_sc)和填充因子略有下降。采用纳秒时间尺度的瞬态吸收光谱技术,从时间分辨的角度分析了钙钛矿电池界面的电子和空穴的复合寿命,对电池性能的变化给出了合理的解释。     

阴极界面修饰层改善平面p-i-n型钙钛矿太阳能电池的光伏性能

有机/无机杂化金属卤化物钙钛矿半导体材料结合了有机材料良好的溶液可加工性以及无机材料优越的光电特性,近几年受到了热捧,成为太阳能电池领域一颗耀眼的明星. 伴随着钙钛矿薄膜结晶过程和形貌的优化、器件结构的改进以及电极界面材料的开发,这类有机/无机杂化金属卤化物钙钛矿太阳能电池的光电转换效率从最初的3.8%迅速提高到目前最高的22.1%. 其中界面工程在提升器件性能上发挥着极其重要的作用. 本文总结了平面p-i-n型钙钛矿太阳能电池中阴极界面修饰层（CBL）的研究进展. CBL从材料上讲可分为无机金属氧化物、金属或金属盐以及有机材料,从构成上讲可分为单层CBL、双层CBLs以及共混型CBL. 本文对这些类型的CBL分别给予详细的介绍. 最后,我们归纳出CBL在改善器件效率和稳定性上所起的作用以及理想CBL所应满足的要求,希望能为以后阴极界面修饰材料的设计提供一定的借鉴.     

A universal tactic of using Lewis-base polymer-CNTs composites as additives for high performance cm~2-sized and flexible perovskite solar cells

Lewis-base polymers have been widely utilized as additives to act as a template for the perovskite nucleation/crystal growth and passivate the under-coordinated Pb2+ sites.However,it is uncovered in this work that the polymer on the perovskite grain boundaries would significantly hinder the charge transport due to its low conductivity,which brings about free carrier recombination and photocurrent losses.To circumvent this issue while fully exploiting the benefits of polymers in passivating the trap states in perovskite,we incorporate highly conductive multiwall carbon nanotubes(CNTs) with Lewis-base polymers as coadditives in the perovskite film.Functionalizing the CNTs with-COOH group enables a selective hole-extraction and charge transport from perovskite to the hole transporting materials(HTM).By studying the charge transporting and recombination dynamics,we revealed the individual role of the polymer and CNTs in passivating the trap states and facilitating the charge transport,respectively.As a result,the perovskite solar cells(PSCs) with polymer-CNTs composites exhibit an impressive PCE of 21.7% for a small-area device(0.16 cm2) and 20.7% for a large-area device(1.0 cm2).Moreover,due to the superior mechanical flexibility of both polymer and CNTs,the polymer-CNTs composites incorporation in the perovskite film encourages the fabrication of flexible PSCs(f-PSCs) with an impressive PCE of 18.3%,and a strong mechanical durability by retaining 80%of the initial PCE after 1,000 times bending.In addition,we proved that the selection criteria of the polymers can be extended to other long-chain Lewis-base polymers,which opens new possibilities in design and synthesis of inexpensive material for this tactic towards the fabrication of high performance large-area PSCs and f-PSCs.     

TiO_2 nanoparticle-based electron transport layer with improved wettability for efficient planar-heterojunction perovskite solar cell

The electron transport layer(ETL) plays an important role in planar heterojunction perovskite solar cell(PSCs),by affecting the light-harvesting, electron injection and transportation processes, and especially the crystallization of perovskite absorber. In this work, we utilized a commercial TKD-TiO_2 nanoparticle with a small diameter of 6 nm for the first time to prepare a compact ETL by spin coating. The packing of small-size particles endowed TKD-TiO_2 ETL an appropriate surface-wettability, which is beneficial to the crystallization of perovskite deposited via solution-processed method. The uniform and high-transmittance TKD-TiO_2 films were successfully incorporated into PSCs as ETLs. Further careful optimization of ETL thickness gave birth to a highest power conversion efficiency of 11.0%, which was much higher than that of PSC using an ETL with the same thickness made by spray pyrolysis. This TKD-TiO_2 provided a universal solar material suitable for the further large-scale production of PSCs. The excellent morphology and the convenient preparation method of TKD-TiO_2 film gave it an extensive application in photovoltaic devices.     

反式锡基钙钛矿光伏电池的制备及稳定性策略

近年来,钙钛矿光伏电池（PSCs）取得了突飞猛进的发展,迄今最高认证光电转换效率达到25.7%,但是钙钛矿材料常使用有毒的重金属元素铅,对环境和人体都有极大的危害,不利于其实际应用,因此发展无铅PSCs受到越来越多的关注。锡基钙钛矿材料具有优异的光电性质,特别是带隙窄、载流子迁移率高和激子复合能低,是无铅钙钛矿中最具有潜力的材料。反式（p-i-n型）锡基PSCs由于低迟滞效应、可低温制备及低成本等优点获得普遍关注,取得了一系列重要突破,目前最高效率已经突破14%,具有巨大的发展潜力。鉴于反式锡基钙钛矿太阳能的迅速发展,本文系统综述了反式锡基PSCs制备及稳定性研究进展,尤其关注反式锡基PSCs的界面修饰、锡基钙钛矿材料性能、构筑高质量锡基钙钛矿薄膜的方法以及提高稳定性的策略,并讨论了锡基PSCs的前景展望。