Compact polarization rotator on silicon for polarization-diversified circuits

We demonstrate a polarization rotator based on adiabatic mode evolution on silicon for polarization-diversified circuits. The rotator has a device length of 420?μm, a polarization-conversion efficiency of more than 90%, and an insertion loss less than 1?dB for a wavelength range of 80?nm. Combining the rotator with a compact, broadband polarization beam splitter based on cascaded directional couplers enhances the polarization conversion extinction ratio to over 30?dB with less than 1.5?dB total insertion loss over a 60?nm spectral range.     

High-efficiency ultrasmall polarization converter in InP membrane

An ultrasmall (<10 μm length) polarization converter in InP membrane is fabricated and characterized. The device relies on the beating between the two eigenmodes of chemically etched triangular waveguides. Measurements show a very high polarization conversion efficiency of >99% with insertion losses of <-1.2 dB at a wavelength of 1.53?μm. Furthermore, our design is found to be broadband and tolerant to dimension variations.     

Efficient and compact TE-TM polarization converter built on silicon-on-insulator platform with a simple fabrication process

An efficient TE-TM polarization converter built on a silicon-on-insulator nanophotonic platform is demonstrated. The strong cross-polarization coupling effect in air-cladded photonic-wire waveguides is employed to realize the conversion. A peak TE-TM coupling efficiency of 87% (-0.6 dB insertion loss) is measured experimentally. A polarization conversion efficiency of >92% with an overall insertion loss of <-1.6 dB is obtained in a wavelength range of 40 nm. The proposed device is compact, with a total length of 44 μm and can be fabricated with one lithography and etching step.     

All-fiber polarization switch

We report an all-fiber polarization switch made out of silica-based microstructured fiber suitable for Q-switching all-fiber lasers. Nanosecond high-voltage pulses are used to heat and expand an internal electrode to cause lambda/2-polarization rotation in less than 10 ns for 1.5 microm light. The 10 cm long component has an experimentally measured optical insertion loss of 0.2 dB and a 0-10 kHz repetition frequency capacity and has been durability tested for more than 10(9) pulses.     

All-fiber narrowband polarization controller based on coherent acousto-optic mode coupling in single-mode fiber

An all-fiber, narrowband, tunable polarization controller is proposed and demonstrated. The device is based on coherent acousto-optic mode coupling induced by two orthogonal acoustic waves on a dispersion-compensating fiber. The cooperative coupling between the two polarizations of the core mode and the TE01 cladding mode through the two gratings permits indirect coupling between the two polarizations of the core mode with nearly 100% efficiency, which makes the polarization-controlling function possible. Experimental results verify the operation of the polarization controller with an insertion loss of <1 dB.     

High-performance and fabrication friendly polarization demultiplexer

A compact and fabrication friendly polarization demultiplexer (P-DEMUX) is proposed and characterized to enable wavelength-division-multiplexing and polarization-division-multiplexing simultaneously. The proposed structure is composed of a polarization-selective microring resonator in ultrathin waveguide and two bus channels in the silicon nitride-silica-silicon horizontal slot waveguides. In the slot waveguide, the transverse electric (TE) mode propagates through the silicon layer, while the transverse magnetic (TM) mode is confined in the slot region. In the designed ultra-thin waveguide, the TM mode is cut-off. The effective indexes of the TE modes for ultrathin and slot waveguides have comparable values. Thanks for these distinguishing features, the input TE mode can be efficiently filtered through the ultra-thin microring at the resonant wavelength, while the TM mode can directly output from the through port. Simulation results show that the extinction ratio of the proposed P-DEMUX for TE and TM modes are 33.21 dB and 24.97 dB, and the insertion losses are 0.346 dB and 0.324 dB, respectively, at the wavelength of 1551.64 nm. Furthermore, the device shows a broad bandwidth ($>100$ nm) for an extinction ratio (ER) of $>20$ dB. In addition, the proposed P-DEMUX also has a good fabrication tolerance for the waveguide width variation of $-20$ nm$\le \Delta w_{\rm g}\le 20$ nm and the microring width variation of $-20$ nm$\le \Delta w_{\rm r}\le $20 nm for a low insertion loss of $<0.75$ dB and low ER of $<-18$ dB.     

基于极化旋转超表面的圆极化天线设计

本文通过设计出一种反射型极化旋转超表面,在8—12 GHz频域内实现高效的极化旋转,并将其加载于微带缝隙天线下方构成新型的极化旋转超表面天线,利用超表面的90°极化旋转效应,成功实现了天线的圆极化辐射调制.仿真与实验结果表明:圆极化天线的中心工作频率为GHz,阻抗带宽为8.3—10 GHz.当微带缝隙天线与极化旋转超表面的间距H=4.5mm时,天线在8.3—8.8 GHz频带内实现了圆极化辐射;当mm时,天线在8.8—9.3 GHz频带内实现了圆极化辐射;当=8mm时,天线在9.3—10 GHz频带内实现了圆极化辐射.实验结果与仿真结果相符,证明了此种设计方法的有效性,也为微带缝隙天线的圆极化设计提供了一种新的途径.     

Ultracompact polarization converter with a dual subwavelength trench built in a silicon-on-insulator waveguide

The design and fabrication of an ultracompact silicon-on-insulator polarization converter is reported. The polarization conversion with an extinction ratio of 16 dB is achieved for a conversion length of only 10 μm. Polarization rotation is achieved by inducing a vertical asymmetry by forming in the waveguide core two subwavelength trenches of different depths. By taking advantage of the calibrated reactive ion etch lag, the two depths are implemented using a single mask and etching process. The measured converter loss is -0.7 dB and the 3 dB bandwidth is 26 nm.     

Theoretical simulation of a polarization splitter based on dual-core soft glass PCF with micron-scale gold wire

A polarization splitter based on dual-core soft glass photonic crystal fiber(PCF) filled with micron-scale gold wire is proposed. The characteristics of the polarization splitter are studied by changing the structural parameters of the PCF and the diameter of the gold wire with the finite element method(FEM). The simulation results reveal that the coupling length ratio of the soft glass-based PCF is close to 2 and the corresponding curve is more flat than that of the silica-based PCF.The broadband bandwidth is 226 nm in which the extinction ratio is lower than-20 d B by the soft glass-based PCF, i.e.,from 1465 nm to 1691 nm which is competitive in the reported polarization splitters, and the bandwidth is just 32 nm by the silica-based PCF. The insertion loss by our polarization splitter is just 0.00248 d B and 0.43 d B at the wavelength of 1.47 μm and 1.55 μm. The birefringence is obviously increased and the coupling length is decreased by filling gold wire into the soft glass-based or the silica-based PCF. Also the birefringence based on the silica-based PCF is much larger than that based on the soft glass-based PCF whether or not the gold wire is introduced. The fabrication tolerance of the polarization splitter is also considered by changing the structural parameters. The polarization splitter possesses broad bandwidth, low insertion loss, simple structure and high fabrication tolerance.     

Design and fabrication of a three-dimensional polymer optical waveguide polarization splitter

We present a design and fabrication of a three-dimensional polymer optical waveguide polarization splitter by taking into consideration of the induced birefringence effect of the polymer. We show that it is not possible to couple TM light from one waveguide to the other but evanescent coupling for TE light is possible. Hence the polarization splitter can be designed by considering TE mode coupling alone. This has an advantage of short interaction length of the device. Based on this consideration, we fabricated a polarization splitter with a TE extinction ratio of 15 dB and TM extinction ratio of 21 dB.     

一款基于多物理场调控的超宽带线-圆极化转换器

为了在微波波段实现可调谐的线-圆极化转换器的设计,结合固态等离子体与二氧化钒设计了一种基于多物理场调控的超宽带线-圆极化转换器,通过改变固态等离子体谐振单元激励状态和人为改变外部温度(T)来实现对该线-圆极化转换器工作频段的调控.采用了全波仿真的方法对该极化转换器的极化转换率曲线、反射相位曲线、轴比曲线、表面电流图进行了计算,并讨论了参数r_1与r_3对轴比的影响.仿真结果表明,当固态等离子体区域均未激励且T68℃时,3 dB轴比频带为14.3—29.7 GHz,相对带宽为70%;当固态等离子体区域均被激励且T68℃时,3 dB轴比频带为14.4—23.4 GHz与28.6—35.9 GHz,相对带宽分别为47.61%和22.64%;当固态等离子体区域未激励且T≥68℃时,3 dB轴比频带为8.4—11.2 GHz与18.7—29.5 GHz,相对带宽分别为28.57%与44.81%.通过改变固态等离子体的激励状态和外部温度,实现了该超宽带线-圆极化转换器工作带宽向高频和低频区域的移动.     

基于SPGD算法的非保偏-保偏光自适应偏振转换

报道了一种基于随机并行梯度下降(SPGD)算法的高消光比非保偏-保偏光自适应偏振转换系统。该系统利用偏振控制器对非保偏光的偏振分量进行直接控制,通过SPGD算法对输出的偏振消光比进行优化,最终实现了自适应的非保偏-保偏光的偏振转换。理论上,结合SPGD算法和偏振控制器的原理,对系统进行分析,建立了非保偏-保偏光自适应偏振转换的数学模型。实验上,利用该系统实现了非保偏到保偏光的转换,获得了14.1dB的线偏振光输出;并利用该系统将任意方向(0~360°)偏振态的线偏振光转换为期望偏振态的高消光比线偏光,其输出线偏光的平均消光比约为12dB。     

Polarization rotator for InP rib waveguide

A polarization rotator, suitable for integration in a polarization diversity optical receiver fabricated in InP technology, is proposed. The device, based on a two steps waveguide rotator, includes tapered input and output ports that provide very low insertion loss (<0.04 dB). An extinction ratio of 40 dB at 1550 nm wavelength is calculated, comparable or even superior to other state of the art polarization converters. The main advantage of the proposed design is the capability of implementation using a standard fabrication process with only two dry etch steps, significantly reducing complexity and cost.     

Highly tolerant tunable waveguide polarization rotator scheme

Integrated polarization rotators are known to exhibit stringent fabrication tolerances, which severely handicap their practical application. Here we present a general polarization rotator scheme that enables both the compensation of fabrication errors and wavelength tunability. The scheme is described analytically, and a condition for perfect polarization conversion is established. Simulations of a silicon-on-insulator polarization rotator show polarization extinction ratios in excess of 40 dB even in the presence of large fabrication errors that in a conventional rotator configuration degrade the extinction ratio to below 5 dB. Additionally, wavelength tuning over ±30 nm is shown.     

A linear-to-circular polarization converter based on I-shaped circular frequency selective surfaces

In this paper, a linear-to-circular polarization converter using a three-layer frequency selective surface based on Ishaped circular structure resonant is presented and investigated. Numerical simulations exhibit that when the normal ypolarized waves impinge on this device propagating towards +z direction, the two orthogonal components of the transmitted waves have a 90° phase difference as well as the nearly equal amplitudes at the resonant frequency of 7.04 GHz, which means that the left-hand circular polarization is realized in transmission. For validating the proposed design, a prototype which consists of 25 × 25 elements has been designed, manufactured and measured. The measured results are in good agreement with the simulated ones, showing that the polarization conversion transmission is over-3 dB in the frequency range of 5.22–8.08 GHz and the axial ratio is below 3 dB from 5.86 GHz to 7.34 GHz.     

硅基槽式微环谐振腔型偏振解复用器全矢量分析

提出一种紧凑型偏振解复用器, 其中两条常规硅基波导作为输入/输出信号通道, 居于其中的槽式微环谐振腔用于偏振态/波长选择组件. 采用全矢量频域有限差分法详细分析了硅基常规及槽波导的模式特性, 结果发现其横磁模的模场布及其有效折射率相似, 而其横电模相应的特性则差异明显, 结果输入横磁模能够在谐振工作波长下从下路端口输出, 而输入横电模与微环耦合可以忽略, 直接从直通端口输出, 从而实现两偏振态的高效分离. 采用全矢量时域有限差分法详细分析了该偏振解复用器的光波传输特性, 结果表明, 当微环半径为3.489 μm时, 在1.55 μm工作波长下, 横磁模与横电模的消光比与插入损耗分别为 ～ 26.12 (36.67) dB与 ～ 0.49 (0.09) dB. 另外, 论文详细讨论了器件关键结构参数的制作容差, 并给出了输入模场在器件中的传输演变情况.     

1.3μm光学环行器正向损耗及反向隔离比的理论及实验研究

在理论及实验上分析了影响光环行器插入损耗及反向隔离比的因素,讨论了环行器中起、检偏镜参数对其性能的影响.结果表明,起、检偏镜的各组参数存在最佳选择,以保证环行器具有低插损、高隔离比及与偏振无关的特性.作者研制的环行器正向损耗小于1dB,反向隔离比在25.5dB与28dB之间.     

Linearized analog photonic links based on a dual-parallel polarization modulator

A linearized analog photonic link (APL) is proposed based on an integratable electro-optic dual-parallel polarization modulator (DPPolM), which consists of two polarization beam splitters and two polarization modulators (PolMs). Theoretical analysis shows that the APL is potentially free from the third-order nonlinear distortion if a polarization controller placed before the DPPolM is carefully adjusted. A proof-of-concept experiment is carried out. A reduction of the third-order intermodulation components as high as 40 dB and an improvement of the spurious-free dynamic range as large as 15.5 dB is achieved as compared with a single PolM-based link. The DPPolM-based APL is simple, compact, and power efficient since it requires only one laser, one modulator, and one photodetector.     

Passive broadband silicon-on-insulator polarization splitter

We present the implementation of a novel wavelength independent polarization splitter on a silicon-on-insulator platform. The waveguide splitter is based on a zero-order arrayed waveguide grating (AWG) configuration. The splitting function is realized by employing cladding stress-induced birefringence. The device demonstrated a TE to TM splitting ratio better than -15 dB over a 20 nm tuning range centered around lambda=1550 nm and better than -10 dB over our entire accessible wavelength range from lambda=1465 nm to 1580 nm. The highest splitting extinction ratio achieved was -20 dB. To our knowledge, this is the first reported passive broadband polarization splitter based on AWG.     

I/Q intensity-demodulation analog photonic link based on polarization modulator

We experimentally investigate a high-linearity analog photonic link based on polarization-modulation in-phase/quadrature (I/Q) intensity-demodulation. In the proposed system, a light wave with its polarization direction oriented at an angle of 45° with respect to the principal axis of the polarization modulator (PolM) is polarization modulated by a drive signal. In the receiver, the polarization-modulated signal is split into two paths using a 50:50 optical coupler (OC). In each path, a polarization beam splitter (PBS) is connected to the PolM via a polarization controller (PC) to realize the in-phase and quadrature signal, respectively. Thanks to the polarization-modulation to intensity-modulation conversion, the fluctuation of the optical phase noise has no impact on the coherent signals. In addition, the use of a single PolM allows the link avoids the matching requirements of dual modulator schemes. The linearization leads to suppression of the third-order intermodulation (IMD3) by more than 40 dB, compared to the quadrature signal. Experimental results show that the link gain is -11.5 dB, noise figure is 26.5 dB, and the third-order limited spurious free dynamic range (SFDR) is 124 dB in a 1 Hz bandwidth.