Study on the relationship between intake of trace elements and breast cancer mortality with chemometric methods

Several chemometric methods were employed to survey the interaction among the trace elements and the relationship between the intake of these elements and the breast cancer mortality. It is indicated that there are strong interactions among the trace elements so as to form a dynamic balance; the intake of Cr is the most important factor that could cause the increase of breast cancer mortality; no definite relation can be observed between the intake of Cu and that of Zn. However, either the ratio of the intake of Cu and that of Zn or the intake of Cd could show a certain state of dynamic balance among some of the trace elements. Comparison of the analytical methods reveals that it is important to select a suitable method so as to obtain the most appropriate explanation.     

Application of laser ablation inductively coupled mass spectrometry (LA-ICP-MS) for the determination of major, minor, and trace elements in bark samples

The large surface area of barks from many tree species enables the effective accumulation of pollutants. Therefore, the analysis of bark material will provide useful information about the degree of pollution of a certain region. The determination of main, minor, and trace elements (Al, Ca, Cd, Ce, Cr, Cu, Fe, Mn, P, Pb, S, Ti and Zn) in bark was performed with an Nd:YAG laser coupled to an ICP-MS system. Bark standards for the calibration by laser ablation ICP-MS were prepared from different bark layers which differ for some relevant elements in concentrations. Four digestion procedures for the decomposition of the standard pellets, the numbers of laser shots per sample and of samples per region necessary have been investigated. Representative results were obtained for 5 or more samples taken from different individuals of one species of a sampling area and the averaged element concentrations of 10 separately placed laser shots for each sample. Laser ablation ICP-MS was applied for the characterization of real bark samples from different regions with high and low pollution burden. It was shown that the method is well suited to characterize different degrees of environmental impact. Anthropogenic sources were responsible for the higher concentrations of most of the elements under investigation. Received: 26 April 1999 / Revised: 24 August 1999 / /Accepted: 28 August 1999     

Application of laser ablation inductively coupled mass spectrometry (LA-ICP-MS) for the determination of major, minor, and trace elements in bark samples

The large surface area of barks from many tree species enables the effective accumulation of pollutants. Therefore, the analysis of bark material will provide useful information about the degree of pollution of a certain region. The determination of main, minor, and trace elements (Al, Ca, Cd, Ce, Cr, Cu, Fe, Mn, P, Pb, S, Ti and Zn) in bark was performed with an Nd:YAG laser coupled to an ICP-MS system. Bark standards for the calibration by laser ablation ICP-MS were prepared from different bark layers which differ for some relevant elements in concentrations. Four digestion procedures for the decomposition of the standard pellets, the numbers of laser shots per sample and of samples per region necessary have been investigated. Representative results were obtained for 5 or more samples taken from different individuals of one species of a sampling area and the averaged element concentrations of 10 separately placed laser shots for each sample. Laser ablation ICP-MS was applied for the characterization of real bark samples from different regions with high and low pollution burden. It was shown that the method is well suited to characterize different degrees of environmental impact. Anthropogenic sources were responsible for the higher concentrations of most of the elements under investigation.     

Investigation of the compatibility between kaempferol and excipients by thermal,spectroscopic and chemometric methods

Journal of Thermal Analysis and Calorimetry - Compatibility is an important step in pre-formulation studies during the development of solid dosage forms. In the present study, we used thermal...     

Examination of distribution of trace elements in hair, fingernails and toenails as alternative biological materials. Application of chemometric methods

The aim of this study was to find correlations between several studied elements and analyzed materials as well as the application and validation of an analytical method to determine trace elements in hair, fingernails and toenails of healthy volunteers (normal concentration). The method developed covers washing, mineralization and ICP-MS determination of 10 elements (Ca, Cd, Co, Cr, Cu, Fe, Mg, Ni, Pb and Zn) in hair and nails. Concentrations of the selected elements in hair, fingernails and toenails were measured for 24 women and 18 men. Furthermore, a chemometric approach (Principal Component Analysis, PCA) was employed to evaluate the correlations between concentrations of the elements in hair and nails and between these materials. Until now PCA has not been frequently applied in handling and interpretation of the results of analysis of biological materials. However, the results of the present investigation show the high potential of PCA in extraction of valuable information from analytical measurements. Additionally, PCA has become a useful tool for visualization of the obtained results. Moreover, the cluster analysis (CA) was used to group the samples according to gender, taking into account two different groups of elements: essential and toxic.      

Application of dried-droplets deposited on pre-cut filter paper disks for quantitative LA-ICP-MS imaging of biologically relevant minor and trace elements in tissue samples

In this work, a novel calibration approach for minor and trace element quantification in LA-ICP-MS imaging of biological tissues is presented. Droplets of aqueous standard solutions are deposited onto pre-cut pieces of filter paper, allowed to dry, and sputtered with a thin gold layer for use as pseudo-internal standard. Analysis of the standards using LA-ICP-MS is performed using radial line-scans across the filters. In contrast to conventionally used preparation of matrix-matched tissue standards, the dried-droplet approach offers a variety of advantages: The standards are easy to prepare, no characterization of the standards using acid digestion is required, no handling of biological materials is necessary, and the concentration range, as well the number of investigated analytes is almost unlimited. The proposed quantification method has been verified using homogenized tissue standards with known analyte concentrations before being applied to a human malignant mesothelioma biopsy from a patient who had not received any chemotherapeutic treatment. Elemental distribution images were acquired at a lateral resolution of 40 μm per pixel, limits of detection ranging from 0.1 μg g⁻¹ (Mn, Ni, Cu, Zn) to 13.2 μg g⁻¹ (K) were reached.     

XRF and TXRF techniques for multi-element determination of trace elements in whole blood and human hair samples

XRF and TXRF were established as useful techniques for multi-element analysis of whole blood and human head hair samples. Direct-XRF with different collimation units and different X-ray excitation modes was successfully used for the determination of S, P, K, Ca, Fe, and Br elements in blood samples and K, Ca, Mn, Fe elements in human hair samples. Direct analysis by TXRF was used for the determination of Rb and Sr in digested blood and human hair samples, respectively, while, the co-precipitation method using APDC for TXRF analysis was used for the determination of Ni, Cu, Zn, and Pb elements in both matrices. As a result, the improved XRF and TXRF methods were applied for multi-element determination of elements in whole blood and human hair samples in non-occupational exposed population living in Damascus city. The mean concentrations of analyzed elements in both matrices were on the reported range values for non-occupational population in other countries.     

Neutron activation analysis applied in sediment samples from the Guarapiranga Reservoir for metals and trace elements assessment

The Guarapiranga Reservoir is a very important aquatic system due to the fact that it is one of the main water reservoirs for South America’s largest city, São Paulo, Brazil. Guarapiranga basin is located within the Metropolitan Region of São Paulo and the reservoir itself is located in the Northern part of the basin occupying approximately 26 km². This reservoir is characterized by environmental impacts from urban invasion, industrial and sewage wastes, all of which seriously affect its water quality and, consequently, the sediment quality. Two collection campaigns were undertaken: April 2009 and June 2010. The samples were analyzed by instrumental neutron activation analysis (INAA) in order to determine the following elements: major (Fe, K and Na), trace (As, Ba, Br, Co, Cr, Cs, Hf, Rb, Sb, Sc, Ta, Tb, Th, U and Zn) and rare earths (Ce, Eu, La, Lu, Nd, Sm, Tb and Yb). The organic matter and granulometric distribution were also evaluated and multivariate analysis was applied to the results. The study of elemental ratios indicated that the amount of elements present in the Guarapiranga Reservoir is mainly of detrital origin.     

Microwave digestion methods for the determination of trace elements in brain and liver samples by inductively coupled plasma mass spectrometry

Two microwave digestion systems (open-focused and closed-pressurized) were tested for the mineralization of human brain and bovine liver (NIST SRM 1577a) as dissolution steps prior to the determination of 16 trace elements (Bi, Cd, Co, Cs, Cu, Fe, Hg, Mn, Mo, Pb, Rb, Sb, Sn, Sr, Tl, and Zn) by inductively coupled plasma mass spectrometry (ICP-MS). Digestion parameters (mass of sample, digestion mixture, and power/time steps) were optimized using temperature and pressure sensors. Digestions with the open-focused microwave system require larger volumes of conc. HNO₃ and 30% H₂O₂ than digestions with the closed-pressurized system. Both systems produce correct results for the bovine liver samples. The concentrations obtained for the digests of the open-focused system tend to be less precise than the concentrations from the closed-pressurized digests. Because the open-focused digests must be diluted to 50 mL to bring the acid concentration to 0.7–2.0 mol/L required by the ICP-MS (closed-pressurized digests need to be diluted to only 20 mL), the detection limits for the system with the open-focused digestion are higher than for the system with the closed-pressurized digestor. The open-focused digestor cannot handle more than 150 mg brain tissue, whereas the closed-pressurized system can mineralize 470 mg. The latter method gave better results with brain tissue than the open-focused system. The preparation of brain tissue as reference material for the determination of trace elements in brain samples is described.     

Microwave digestion methods for the determination of trace elements in brain and liver samples by inductively coupled plasma mass spectrometry

Two microwave digestion systems (open-focused and closed-pressurized) were tested for the mineralization of human brain and bovine liver (NIST SRM 1577a) as dissolution steps prior to the determination of 16 trace elements (Bi, Cd, Co, Cs, Cu, Fe, Hg, Mn, Mo, Pb, Rb, Sb, Sn, Sr, Tl, and Zn) by inductively coupled plasma mass spectrometry (ICP-MS). Digestion parameters (mass of sample, digestion mixture, and power/time steps) were optimized using temperature and pressure sensors. Digestions with the open-focused microwave system require larger volumes of conc. HNO(3) and 30% H(2)O(2) than digestions with the closed-pressurized system. Both systems produce correct results for the bovine liver samples. The concentrations obtained for the digests of the open-focused system tend to be less precise than the concentrations from the "closed-pressurized" digests. Because the "open-focused" digests must be diluted to 50 mL to bring the acid concentration to 0.7-2.0 mol/L required by the ICP-MS (closed-pressurized digests need to be diluted to only 20 mL), the detection limits for the system with the open-focused digestion are higher than for the system with the closed-pressurized digestor. The open-focused digestor cannot handle more than 150 mg brain tissue, whereas the closed-pressurized system can mineralize 470 mg. The latter method gave better results with brain tissue than the open-focused system. The preparation of brain tissue as reference material for the determination of trace elements in brain samples is described.     

Chromatographic and spectroscopic methods for the identification of alkaloids from herbarium samples of the genus Uncaria.

A combination of thin-layer chromatography, gas-liquid chromatography, ultraviolet spectroscopy and mass spectrometry techniques for the alkaloid screening of herbarium samples of the genus Uncaria (Rubiaceae) is described. Some sixty alkaloids are distinguished by the screening procedure, and they represent heteroyohimbine, oxindole, roxburghine, simple beta-carboline, pyridino-indolo-quinolizidinone and gambirtannine types.     

Present-day methods for the determination of trace elements in oil and its fractions

The development and use of instrumental methods for the determination of a wide range of trace elements in oil is considered. Special attention is paid to methods of the direct introduction of samples into spectrometers. It is shown that preliminary sample preparation is in certain cases necessary for the determination of trace elements in oil. The main methods of sample preparation of oils, including methods of extraction of a series of trace elements from crude oil (extraction, membrane, sorption, etc.), are described.     

Application of chitosan functionalized with 3,4-dihydroxy benzoic acid moiety for on-line preconcentration and determination of trace elements in water samples

Chitosan resin functionalized with 3,4-dihydroxy benzoic acid (CCTS-DHBA resin) was used as a packing material for flow injection (FI) on-line mini-column preconcentration in combination with inductively coupled plasma-atomic emission spectrometry (ICP-AES) for the determination of trace elements such as silver, bismuth, copper, gallium, indium, molybdenum, nickel, uranium, and vanadium in environmental waters. A 5-mL aliquot of sample (pH 5.5) was introduced to the minicolumn for the adsorption/preconcentration of the metal ions, and the collected analytes on the mini-column were eluted with 2 M HNO₃, and the eluates was subsequently transported via direct injection to the nebulizer of ICP-AES for quantification. The parameters affecting on the sensitivity, such as sample pH, sample flow rate, eluent concentration, and eluent flow rate, were carefully examined. Alkali and alkaline earth metal ions commonly existing in river water and seawater did not affect the analysis of metals. Under the optimum conditions, the method allowed the determination of metal ions with detection limits of 0.08 ng mL⁻¹ (Ag), 0.9 ng mL⁻¹ (Bi), 0.07 ng mL⁻¹ (Cu), 0.9 ng mL⁻¹ (Ga), 0.9 ng mL⁻¹ (In), 0.08 ng mL⁻¹ (Mo), 0.09 ng mL⁻¹ (Ni), 0.9 ng mL⁻¹ (U), and 0.08 ng mL⁻¹ (V). By using 5 mL of sample solution, the enrichment factor and collection efficiency were 8–12 fold and 96–102%, respectively, whereas the sample throughput was 7 samples/hour. The method was validated by determining metal ions in certified reference material of river water (SLRS-4) and nearshore seawater (CASS-4), and its applicability was further demonstrated to river water and seawater samples.     

Ionic liquid based dispersive liquid-liquid microextraction combined with ICP-OES for the determination of trace quantities of cobalt, copper, manganese, nickel and zinc in environmental water samples

We describe a method for ionic liquid based dispersive liquid-liquid microextraction of Co(II), Cu(II), Mn(II), Ni(II) and Zn(II), followed by their determination via flow injection inductively coupled plasma optical emission spectrometry. The method is making use of the complexing agent 1-(2-thenoyl)-3,3,3-trifluoracetone, the ionic liquid 1-hexyl-3-methyl imidazolium bis(trifluoromethylsulfonyl)imide, and of ethanol as the dispersing solvent. After extraction and preconcentration, the sedimented ionic liquid (containing the target analytes) is collected, diluted with 1-propanol, and introduced to the ICP-OES. Effects of pH, ionic strength, ligand to metal molar ratio, volumes of extraction and disperser solvents on the performance of the microextraction were optimized in a half-fractional factorial design. The significant parameters were optimized using a face-centered central composite design. The method has detection limits between 0.10 and 0.20?ng?mL^?1 of the metal ions, preconcentration factors between 79 and 102, linear responses in 0.25 to 200?ng?mL^?1 concentration ranges, and relative standard deviations of 3.4 to 6.0%. The method was successfully applied to the analysis of drinking water, a fish farming pond water, and waste water from an industrial complex.

Determination of metals in biofluids and tissues: sample preparation methods for atomic spectroscopic techniques

Several sample preparation methods unique to each instrumental technique exist for the elemental analysis of biological specimens, but no review or book has dealt with them. The present review is an attempt to fill this void and focuses on sample preparation methods unique to atomic and X-ray spectroscopic techniques. The techniques covered are: flame and electrothermal AAS, inductively coupled plasma atomic emission spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS) and X-ray fluorescence spectrometry (XRF) since these are most commonly used in trace element analysis of biological materials. The intent is not to present the procedural details for the various tissues or elements, but rather to highlight the methods which are unique to each instrument. The bibliography accompanying this review should aid the analytical chemist in his/her search for the detailed preparation protocols.     

Adsorptive stripping voltammetry of some trace elements in biological samples,II: Nickel,arsenic, aluminium and selenium

A study of the adsorptive stripping voltammetry of nickel, aluminium, selenium and arsenic is reported in which 2,5-dimercapto-1,3,4-thiadiazole (DMTD) has been used as a chelating agent. By a suitable choice of deposition potential, deposition time, reagent reaction time and other operating conditions, the determination of the four elements could be achieved.By the use of benzyltrimethyl ammonium methoxide as a digesting solvent, it was possible to apply the procedure to the direct determination of the four elements in biological samples.     

The application and comparison of several chemometric methods of excitation-emission matrix spectra in studying the interactions of metal complexes with DNA

The interactions of fs DNA and two metal complexes [Cu(phen)SO₄]·2H₂O and [Ni(phen)SO₄]·2H₂O were explored by several chemometric methods, including parallel factor (PARAFAC), singular value decomposition-least squares (SVD-LS), and singular value decomposition-nonnegative least squares (SVD-NNLS) of excitation-emission matrix spectra (EEMs). The applications of SVD-LS and SVD-NNLS in this domain have been discussed. Rayleigh scatter part is avoided by ordered zero and reconstructed by linear interpolation. The importance of avoiding Rayleigh scatter has also been discussed. All the three methods do well in qualitative analysis. SVD-LS does best in present small changes of ethidium bromide (EB). In order to get accurate results, PARAFAC and SVD-NNLS can be utilized together in quantitative analysis. All the three chemometric methods indicate that the DNA binding modes of [Cu(phen)SO₄]·2H₂O are hydrogen bond effect and intercalation, while intercalation is the only DNA binding mode for [Ni(phen)SO₄]·2H₂O. These results are verified by the electronic absorption and emission fluorescence spectra. Just like PARAFAC, both SVD-LS and SVD-NNLS are proven to be convenient and convincing in studying the interactions between nucleic acids and complexes.     

The use of electrothermal vaporization ICP-OES for the determination of trace elements in human hair using slurry sampling and PTFE as modifier

A procedure for the determination of trace elements in human hair has been proposed by electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) with slurry sampling. Slurry was prepared by immersing human hair with conc. HNO₃ and then adding a polytetrafluoroethylene (PTFE) slurry, which was used as a chemical modifier for the improvement of vaporization characteristic of analyte. The slurry was homogenized with an ultrasonic vibrator before the measurement. The vaporization behaviour of the analytes in slurry and solution and the main influence factors for the determination were studied with the addition of PTFE systematically. Detection limits for this method varied from 0.033?µg?g^?1 (Cu) to 3.21?µg?g^?1 (Zn) with the relative standard deviations (RSDs) of 2.8–7.1%. The proposed method was successfully applied for the determination of trace elements (Cu, Mn, Cr, Fe, Zn, Cd and Pb) in human hair with minimum chemical pretreatment and aqueous calibration. The accuracy was checked by comparing the results of this method with those using pneumatic nebulization (PN) ICP-OES after a conventional acid decomposition of the same sample. In addition, the standard reference material of human hair (GBW 07601) was analysed with good agreement between the results from the proposed method and the certified values.     

A system for the neutron activation analysis of trace elements in samples of biological and environmental interest

A neutron activation, ion exchange group separation and iterative least squares γ-ray spectroscopy method has been evaluated. This technique is suitable for multiple trace element analysis in a wide range of biological and environmental materials, since the major contaminants,²⁴Na,³²P, and⁴²K, are removed by an anion exchange resin and do not interfere with the analysis of the majority of the trace elements present. The iterative least squares method was tested with a mixture of standards. The reproducibility and accuracy varied from 3 to 26%. The larger uncertainties resulted from (1) the limited statistical accuracy associated with a low counting rate, and (2) bias introduced by the contaminants in the library of standard spectra even though radiochemical purity exceeded 99.8%. The rigorous least squares method can accurately compensate for instrumental drifts so that the sensitivity approaches the limit imposed by the statistical accuracy of the data and of the standard spectra. Minor components of the complex γ-spectrum were resolved and proved to be present at levels as low as 0.8% of the integral counting rate.     

Reference materials and analytical standards to stimulate improved laboratory performance: Experience from the external quality assessment scheme for trace elements in biological samples

The performance of a large number of laboratories measuring trace elements in biological fluids has been monitored over many years by examination of their results in the Guildford external quality assessment scheme. Specific experiences of the UK trace elements reference laboratories have been used to stimulate improvements in performance of other participants in the scheme. The key features of these initiatives were: specially prepared reference materials, used as internal quality control specimens within a common procedure, contributed to accuracy control; proposed standards of satisfactory and unacceptable analytical performance associated with a new system for scoring; regular non-threatening open discussion of performance with interested colleagues. The impact of these features is illustrated with reference to measurements of Al and Zn in serum and Pb in whole blood.