Effect of porosity and pore morphology on the low-frequency dielectric response in sintered ZrO<Subscript>2</Subscript>—8 mol% Y<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramic compact

Effect of porosity and pore size distribution on the low-frequency dielectric response, in the range 0.01–100 kHz, in sintered ZrO₂—8 mol% Y₂O₃ ceramic compacts have been investigated. Small-angle neutron scattering (SANS) technique has been employed to obtain the pore characteristics like pore size distribution, specific surface area etc. It has been observed that the real and the imaginary parts of the complex dielectric permittivity, for the specimens, depend not only on the porosity but also on the pore size distribution and pore morphology significantly. Unlike normal Debye relaxation process, where the loss tangent vis-à-vis the imaginary part of the dielectric constant shows a pronounced peak, in the present case the same increases at lower frequency region and an anomalous non-Debye type relaxation process manifests.     

Effects of sintering temperature on the structure and electrochemical performance of Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript> cathode materials

The objective of the present study was to investigate the effects of sintering temperature on the structure and electrochemical performance of Mg₂SiO₄ cathode materials using sol-gel method. X-ray diffraction and Fourier-transform infrared analysis were used to study the structural properties of the materials. The temperatures applied in the sintering process influenced the structure, morphology, as well as particle size distribution of the Mg₂SiO₄. All samples sintered at temperatures of 900, 1000, and 1100 °C yielded pure Mg₂SiO₄ compounds consisting of orthorhombic crystalline phase with a space group of Pbnm. Particle size and lattice parameters of Mg₂SiO₄ samples increased with the increases of sintering temperature due to an increase of the nucleation and crystal growth rates. The cyclic voltammetry analysis showed the presence of redox reaction. This result shows that the Mg₂SiO₄ material has potential to be used as cathode materials in magnesium rechargeable batteries.     

Structural and electrical properties of KCa<Subscript>2</Subscript>Nb<Subscript>5</Subscript>O<Subscript>15</Subscript> ceramics

A polycrystalline sample of KCa₂Nb₅O₁₅ with tungsten bronze structure was prepared by a mixed oxide method at high temperature. A preliminary structural analysis of the compound showed an orthorhombic crystal structure at room temperature. Surface morphology of the compound shows a uniform grain distribution throughout the surface of the sample. Studies of temperature variation on dielectric response at various frequencies show that the compound has a transition temperature well above the room temperature (i.e., 105°C), which was confirmed by the polarization measurement. Electrical properties of the material have been studied using a complex impedance spectroscopy (CIS) technique in a wide temperature (31–500°C) and frequency (10²–10⁶ Hz) range that showed only bulk contribution and non-Debye type relaxation processes in the material. The activation energy of the compound (calculated from both the loss and modulus spectrum) is same, and hence the relaxation process may be attributed to the same type of charge carriers. A possible ‘hopping’ mechanism for electrical transport processes in the system is evident from the modulus analysis. A plot of dc conductivity (bulk) with temperature variation demonstrates that the compound exhibits Arrhenius type of electrical conductivity.      

Low-temperature sintering effects on NASICON-structured LiSn<Subscript>2</Subscript>P<Subscript>3</Subscript>O<Subscript>12</Subscript> solid electrolytes prepared via citric acid-assisted sol-gel method

LiSn₂P₃O₁₂ with sodium (Na) super ionic conductor (NASICON)-type rhombohedral structure was successfully obtained at low sintering temperature, 600 °C via citric acid-assisted sol-gel method. However, when the sintering temperature increased to 650 °C, triclinic structure coexisted with the rhombohedral structure as confirmed by X-ray diffraction analysis. Conductivity–temperature dependence of all samples were studied using impedance spectroscopy in the temperature range 30 to 500 °C, and bulk, grain boundary and total conductivity increased as the temperature increased. The highest bulk conductivity found was 3.64?×?10^?5 S/cm at 500 °C for LiSn₂P₃O₁₂ sample sintered at 650 °C, and the lowest bulk activation energy at low temperature was 0.008 eV, showing that sintering temperature affect the conductivity value. The voltage stability window for LiSn₂P₃O₁₂ sample sintered at 600 °C at ambient temperature was up to 4.4 V. These results indicated the suitability of the LiSn₂P₃O₁₂ to be exploiting further for potential applications as solid electrolytes in electrochemical devices.     

Local structure of disordered PbSc<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript> in the region of the diffuse tetragonal phase-rhombohedral phase transition

The local structure of the ferroelectric-relaxor PbSc_1/2Nb_1/2O₃ in the temperature range from 550 to 220 K has been investigated using ⁴⁵Sc nuclear magnetic resonance. It has been found that, in the paraelectric phase at temperatures below 550 K, the crystal consists of regions of an ordered elpasolite structure and inclusions of the disordered tetragonal perovskite phase with displacements along directions of the [001] type. The relative weight of the tetragonal structure in the region of the paraelectric phase is approximately equal to 0.28. Below the temperature of the phase transition from the disordered modification to the polar phase, the relative weight of the tetragonal phase decreases with decreasing temperature. The tetragonal structure is replaced by the trigonal polar structure. In a wide temperature range (∼50 K), there exists a heterophase structure that is characteristic of relaxors. Note that the correlation length of displacements in the tetragonal phase should be very small to explain the absence of indications of the existence of this phase in the diffraction data.     

Luminescence properties of transparent ceramics Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>:Yb

We present the results of studying the luminescence properties of transparent ceramics Y₃Al₅O₁₂:Yb obtained by the vacuum sintering and nanocrystalline technology. In the course of research, we measured the luminescence and luminescence excitation spectra, as well as the temperature and kinetic behavior of luminescence. Our results are analyzed in comparison with the characteristics of corresponding single crystals. We revealed that processes of generation and relaxation of electronic excitations that occur in ceramics, in particular, in the charge transfer state, are similar to processes occurring in crystals. The behavior of two charge-transfer luminescence bands at 340 and 490 nm is studied. In the range 300–600 nm, we revealed a broad emission band of radiation of other type, which is also observed in spectra of undoped ceramics. This broad band is attributed to F⁺ centers. Emission and excitation spectra of charge transfer luminescence at a maximum of the temperature dependence of 100 K are measured for the first time. We found that, upon excitation in the charge transfer band, luminescence in ceramics is more intense than in single crystals with similar concentrations of Yb and has a higher quenching temperature.     

Modulated magnetic structure in quasi-one-dimensional clinopyroxene NaFeGe<Subscript>2</Subscript>O<Subscript>6</Subscript>

The magnetic structure of the NaFeGe₂O₆ monoclinic compound has been experimentally investigated using the elastic scattering of neutrons. At a temperature of 1.6 K, an incommensurate magnetic structure has been observed in the form of an antiferromagnetic helix formed by a pairs of the spins of the Fe³⁺ ions with helical modulation in the ac plane of the crystal lattice. The wave vector of the magnetic structure has been determined and its temperature behavior has been studied. The analysis of the temperature dependences of the specific heat and susceptibility, as well as the isotherms of the field dependence of the magnetization, has revealed the existence of not only the order-disorder magnetic phase transition at the point T _N = 13 K, but also an additional magnetic phase transition at the point T _c = 11.5 K, which is assumingly an orientation phase transition.     

Combustion synthesis of magnesium ferrite as liquid petroleum gas (LPG) sensor: Effect of sintering temperature

We report synthesis of Spinel type magnesium ferrite (MgFe₂O₄) material by a simple, inexpensive combustion method with glycine as a fuel and their application as a gas sensor for reducing gases (LPG, Acetone, Ethanol, Ammonia). The dependence of reducing gas sensing properties on the structural and surface morphological properties has been studied as an effect of sintering temperatures. The structural and surface morphological properties were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The MgFe₂O₄ were highly oriented along (311) with the spinel type crystal structure. The SEM observation reveals that porous morphology decreases due to the grain growth as sintering temperature increases. The mechanism of reducing gas sensing by the MgFe₂O₄ pellets is explained on the basis of adsorbed oxygen on the sensor surface. The selectivity and maximum response of 71% to 2000 ppm of LPG was observed at 698 K with the (MgFe₂O₄) material sintered at 1173 K.     

NO<Subscript>2</Subscript>-sensing properties of La<Subscript>0.65</Subscript>Sr<Subscript>0.35</Subscript>MnO<Subscript>3</Subscript> synthesized by self-propagating combustion

Ultrafine-structure La_0.65Sr_0.35MnO₃ (LSM) powders synthesized by self-propagating combustion method have been used to fabricate sensing electrodes (SEs) for NO₂ mixed-potential sensors based on yttria-stabilized zirconia (YSZ). This type of sensor was found to provide better NO₂ sensitivity at 500 °C than sensors with LSM powders synthesized by traditional solid-state methods. The response values of the sensor have good linear relationship (sensitivity 36.6 mV/decade and linear fit 0.99) with the logarithm of NO₂ concentration varying from 30 to 500 ppm. The influence of sintering temperature (1000, 1100, 1200, and 1300 °C) on sensor response was also examined and was found to have a significant effect on the morphology of LSM-SEs. Moreover, in the presence of NO, CO₂, CO, and NO₂, the sensor exhibited good NO₂ selectivity.     

Antisite defect types and temporal evolution characteristics of D0<Subscript>22</Subscript>-Ni<Subscript>3</Subscript>V structure: Studied by the microscopic phase field

Microscopic phase field simulation is performed to study antisite defect type and temporal evolution characteristic of D0₂₂-Ni₃V structure in Ni₇₅Al _x V_25−x ternary system. The result demonstrates that two types of antisite defect V_Ni and Ni_V coexist in D0₂₂ structure; however, the amount of Ni_V is far greater than V_Ni; when precipitates transform from D0₂₂ singe phase to two phases mixture of D0₂₂ and L1₂ with enhanced Al:V ratio, the amount of V_Ni has no evident response to the secondary L1₂ phase, while Ni_V exhibits a definitely contrary variation tendency: Ni_V rises without L1₂ structure precipitating from matrix but declines with it; temporal evolution characteristic and temperature dependent antisite defect V_Ni, Ni_V are also studied in this paper: The concentrations of the both defects decline from high antistructure state to equilibrium level with elapsed time but rise with elevated temperature; the ternary alloying element aluminium atom occupies both α and β sublattices of D0₂₂ structure with a strong site preference of substituting α site. Supported by the National Natural Science Foundation of China (Grant Nos. 50671084 and 50875217), the Doctorate Foundation of Northwestern Polytechnical University of China (Grant No. CX200806), the China Postdoctoral Science Foundation Funded Project (Grant No. 20070420218), and the Natural Science Foundation of Shaanxi Province of China     

Thermal hysteresis of a simulated Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Thermal hysteresis in a simulated Al₂O₃ system has been investigated using a Molecular Dynamics (MD) method. Simulations were done in the basic cube under periodic boundary conditions containing 3000 ions with Born-Mayer type pair potentials. The system was cooled down from 7000 K to 0 K and heated up from 0 K to 7000 K by the same cooling/heating rate of 1.7178×10¹⁴ K/s. The temperature dependence of the system density upon cooling and heating shows thermal hysteresis. The differences between structure and dynamics of the models obtained by cooling (MOBC) and heating (MOBH) at three different temperatures of 2100 K, 3500 K and 5600 K have been detected. Calculations show that the differences in the dynamics of the systems are more pronounced than those in the structure. Furthermore, dynamical heterogeneities in MOBC and MOBH at the temperature of 2100 K have been studied through a non-Gaussian parameter and comparison of partial radial distribution functions (PRDFs) for the 10% most mobile or immobile particles with their corresponding mean ones. Cluster size distributions of the 10% most mobile or immobile particles in MOBC and MOBH at the temperature of 2100 K have been obtained. Calculations show that differences in dynamical heterogeneities are pronounced.     

Phonon linewidths in YNi<Subscript>2</Subscript>B<Subscript>2</Subscript>C

Phonons in a metal interact with conduction electrons which give rise to a finite linewidth. In the normal state, this leads to a Lorentzian shape of the phonon line. Density functional theory is able to predict the phonon linewidths as a function of wave vector for each branch of the phonon dispersion. An experimental verification of such predictions is feasible only for compounds with very strong electron-phonon coupling. YN₂B₂C was chosen as a test example because it is a conventional superconductor with a fairly high T _c (15.2 K). Inelastic neutron scattering experiments did largely confirm the theoretical predictions. Moreover, they revealed a strong temperature dependence of the linewidths of some phonons with particularly strong electron-phonon coupling which can as yet only qualitatively be accounted for by theory. For such phonons, marked changes of the phonon frequencies and linewidths were observed from room temperature down to 15 K. Further changes were observed on entering into the superconducting state. These changes can, however, not be described simply by a change of the phonon linewidth.      

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Effect of Al-Mo codoping on the structure and ionic conductivity of sol-gel derived Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript> ceramics

Al-Mo codoped Li₇La₃Zr₂O₁₂ ceramics with fine grain were prepared by sol-gel method. The influences of Al-Mo codoping on the structure, microstructure, and conductivity of Li₇La₃Zr₂O₁₂ were investigated by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and impedance spectroscopy. The cubic phase Li₇La₃Zr₂O₁₂ has been stabilized by partial substitution of Al for Li and Mo for Zr. Li_6.6-3yAl_yLa₃Zr_1.8Mo_0.2O₁₂ (0?≤?y?≤?0.1) has been sintered at 1040–1060 °C for 3 h. The liquid sintering facilitated its densification. The relative density of the composition with x?=?0.075 was approximately 96.4%. Results indicated that the Al-Mo codoped LLZO synthesized by sol-gel method effectively lowered its sintering temperature, accelerated densification, and improved the ionic conductivity.     

Preparation and characterization of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> nanorod by low heating solid state coordination method

Cathode material LiMn₂O₄ nanorod was prepared by annealing of the mixed precursor which was synthesized by low heating solid state coordination method using lithium acetate, manganese acetate and oxalic acid as starting materials. The structures and morphologies of the LiMn₂O₄ nanorod were investigated as a function of annealing temperature and time. The results showed that all samples in different annealing temperatures and time have the same spinel structure. The higher the annealing temperature is, the more complete the crystal structure forms, and the larger the particle size is. In addition, the electrochemical properties of the LiMn₂O₄nanorod were studied in this paper.     

Large influence of the synthesis conditions on the physico-chemical properties of nanostructured Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>

Magnetite synthesized via three different synthesis routes (coprecipitation process in aqueous media, electrochemical synthesis in presence of complexing agents and solid state reaction at high temperature) has been characterized by X-Ray diffraction, scanning electron microscopy, thermal analysis (TGA), FT-IR and Mössbauer spectroscopies. Although each procedure gave homogeneous magnetite powders, many differences could be seen in the physico-chemical properties of the samples mostly depending on the synthesis conditions. For instance, at least two factors seem to have a huge impact onto the Fe₃O₄ behaviour: the presence of hydration water molecules and the particle size of the powders since a superparamagnetic behaviour was observed with the thinnest particles, at room temperature, on the Mössbauer spectra via the appearance of line broadening and a pronounced central doublet.     

Theoretical study of aging effects on LaNi<Subscript>5</Subscript> tritium storage

The electronic structure and energy of La₂Ni₁₀H₁₂ and La₂Ni₁₀H₁₁He (He is at tetrahedral, octahedral or twelve-face polyhedral interstitials) double cells have been calculated using the density functional theory. Their equilibrium structure, energy bands, electronic density of states (DOS) and X-ray diffraction are presented and discussed. The results indicate the helium-3 produced due to the decay of tritium is most possibly sited at twelve-face polyhedral and octahedral interstices and changes the thermodynamic properties of LaNi₅ tritide system. The changes due to aging such as the reduction in the isotherm plateau pressure, increase of the isotherm plateau slope, and appearance of deeply trapped hydrogen are caused not only by the lattice expansion, but also by modification of the electronic structure due to the presence of He.     

Effect of heat treatment on pore structure in nanocrystalline NiO: A small angle neutron scattering study

Nanocrystalline nickel oxide powders were calcined at 300, 600 and 900°C and pore structure evolution was followed by small angle neutron scattering (SANS). Pore size distributions at two widely separated size ranges have been revealed. Shrinkage of larger-sized pore with reduction in polydispersity has been observed with increasing heat treatment temperature. The pore structures at various heat treatment temperatures do not scale. This has been attributed to the grain boundary diffusion leading to an asymmetric shrinkage of the pores.      

Structural transformations in the Al<Subscript>85</Subscript>Ni<Subscript>6.1</Subscript>Co<Subscript>2</Subscript>Gd<Subscript>6</Subscript>Si<Subscript>0.9</Subscript> amorphous alloy during multiple rolling

The effect of multiple rolling at room temperature on the structure and crystallization of the Al₈₅Ni_6.1Co₂Gd₆Si_0.9 amorphous alloy has been studied using transmission electron microscopy, differential scanning calorimetry, and X-ray diffraction. The total plastic strain is 33%. It has been shown that the deformation results in the formation of aluminum nanocrystals with the average size that does not exceed 10–15 nm. The nanocrystals are formed in regions of localization of plastic deformation. The deformation decreases the thermal effect of nanocrystallization (∼15%) as compared to the heat release at the first stage of crystallization of the unstrained sample. The morphology, structure, and distribution of precipitates have been investigated. Possible mechanisms of the formation of nanocrystals during the deformation have been discussed.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.