催化动力学分光光度法测定微量铁的研究

在 Na2 HPO4介质中 ,研究了 Fe( )催化 H2 O2 氧化甲基百里酚蓝褪色指示反应及其动力学条件 ,建立了测定痕量铁的新方法。方法的线性范围为 0 .0 2～ 0 .2 5μg/2 5m L,检出限为 0 .0 1 2 μg/2 5m L。用以测定过氧化碳酸钠 ( 2 Na2 CO3· 3H2 O2 )中的铁 ,结果令人满意。     

火焰原子吸收法测定空气与废气中的铅(铅尘和铅烟)

采用火焰原子吸收法监测空气与废气中气溶胶样品的铅尘和铅烟 ,依照有关部门已制订的一批统一 (或推荐 )的监测方法资料 ,通过自身一系列的方法适用性检验 ,经外场的采样效率试验直至实验室内的空白值、酸度及样品基体干扰影响和消除的尝试 ,加以改变仪器工作条件比对和回收试验等 ,使实测样品获得了满意结果。铅的方法检出限为 0 0 5 μg/mL/ 1 %吸收 ,测定下限为 0 1 5 μg/mL ,线性范围 0 5～ 1 0 0 μg/mL ,测定范围 :0 0 5～ 5 0mg/m3 ,当采样体积为 5 0m3 ,取 1 / 2张滤膜 (直径 8～ 1 0cm)进行铅尘测定时气溶胶中铅的最低检出浓度为 2× 1 0 - 4mg/m3 ,采样效率为 98% ,样品回收率为 92 3%。     

二甲基黄催化动力学光度法测定痕量钯

根据在 H2 SO4 介质中钯 ( )催化高碘酸钾氧化二甲基黄的褪色反应 ,提出了测定钯的新催化光度法。钯浓度在 0 .0～ 6.0μg/2 5 m L范围内与催化反应速率呈良好的线性关系。方法的检出限为 2 .1 9× 1 0 - 3μg /m L。对 3.0μg/2 5 m L钯 ( )测定的相对标准偏差为 0 .78% ( n=1 1 )。此法用于某些催化剂中钯的测定 ,标准加入回收率为 99.5 %～ 1 0 4 .1 %。     

高碘酸盐氧化耐尔蓝动力学光度法测定锇

在硫酸介质和热水浴中 ,Os( )对高碘酸盐氧化耐尔蓝有催化作用。研究了反应速率对酸度、浓度、温度和离子强度的依赖关系 ,采用 0 .0 1 0mol/ L硫酸 ,反应的灵敏度随温度升高而增大 ,反应速率对反应混合物的离子强度依赖较小。线性范围为 0～ 0 .2 5μg/ 2 5m L;检出限为 8.0 2× 1 0 -5 μg/ m L;对质量浓度为 0 .1 0 μg/ 2 5m L 的 Os( )测定的相对标准偏差为 1 .0 2 % ( n=1 1 ) ;导出了催化反应的动力学方程 ;探讨了反应机理。4 0 0倍量以上常见金属离子不干扰锇的测定 ,1 0倍量以上的 Ru( )、Fe3 +有干扰。本法已用于贵金属冶金样品中锇的测定。     

气相色谱法分离和测定环境空气中的丙烯酸乙酯和甲基丙烯酸甲酯

用活性炭吸附环境空气中的丙烯酸乙酯和甲基丙烯酸甲酯 ,经二硫化碳 (CS2 )解吸后用气相色谱法测定 .在填充 2 .5 %DNP + 2 .5 %Bentone 34/ChromosorbWHPDMCS的玻璃色谱柱 (长 2m内径 3mm)上 ,丙烯酸乙酯与甲基丙烯酸甲酯及干扰物之间能较好地分离 .方法的回收率 :丙烯酸乙酯为 86.4%～ 1 0 3.0 % ,甲基丙烯酸甲酯为 86.3 %～ 1 0 1 .2 % ,变异系数 :丙烯酸乙酯为 4.1 %～ 4.4% ,甲基丙烯酸甲酯为 4.4%～ 4.9% ,当采样体积为 2 0L ,解吸液体积为 2 .0 0mL ,进样 2 μL时 ,丙烯酸乙酯和甲基丙烯酸甲酯的最低检测浓度分别为 0 .0 2mg/m3和 0 .0 1mg/m3.     

新显色剂三甲氧基苯基荧光酮光度法测定锗

研究了新试剂三甲氧基苯基荧光酮光度测定锗的方法。在 3mol/ m LH3PO4 介质中 ,当 Triton X- 1 0 0存在时 ,锗与三甲氧基苯基荧光酮形成 1∶ 2橘红色络合物 ,最大吸收在 5 0 5 nm波长处 ,摩尔吸光系数为 1 .7× 1 0 5L· mol-1·cm-1且具有高的选择性。当锗含量在 0～ 6μg/ 2 5 m L范围内符合比尔定律。已用于大蒜与枸杞子中锗的测定     

阻抑动力学光度法测定白鼠肝脏中的超痕量镍(Ⅱ)

在 NH3- H2 O- NH4 Cl介质中 ,超痕量镍 ( )能阻抑 H2 O2 氧化甲基紫褪色的指示反应 ,研究了阻抑褪色反应的最佳条件和动力学参数 ,建立了测定超痕量镍 ( )的新方法。方法检出限为 4.4× 1 0 -11g/m L Ni( ) ,测定范围为 0～1 .0μg/2 5m L。方法已用于测定生物样品中的 Ni( )。     

高效液相色谱法测定人血浆中的芦氟沙星

 建立了测定人血浆中芦氟沙星质量浓度的高效液相色谱法 ,血浆用二氯甲烷提取 3次 ,以 UltrasphereODS(4.6mm i.d.× 2 5 0 mm)为色谱柱 ,流动相为甲醇 -1 0 mmol/L 溴化四丁铵 -三乙胺 (体积比为 3 2∶ 68∶0 .5 ) ,用磷酸调 p H2 .8,检测波长 2 95 nm,流速为 1 .2 m L/min,以培氟沙星为内标。血浆中芦氟沙星的线性范围为 0 .1～ 1 0 mg/L ,最低检测质量浓度为 0 .0 5 mg/L ,回收率为 99.7% ,日内、日间 RSD分别为 2 .3 3 %和3 .83 %。方法简便、快速、准确 ,适用于人血浆中芦氟沙星质量浓度的测定。     

催化动力学光度法测定井水中痕量锰

研究了在 NH3· H2 O- NH4 Cl介质中锰催化过氧化氢氧化苋菜红的褪色反应及其动力学条件 ,测定了反应级数和表观活化能 ,建立了测定痕量锰的新方法。该方法的检出限为 2 .7× 1 0 -4 μg/m L Mn,线性范围为 0～ 2 .4μg/2 5m LMn。用于测定井水中痕量 Mn,与原子吸收法的测定结果一致。     

碘化钾碘蓝分光光度法测定微量过氧化氢

基于在酸性介质中 ,过氧化氢与碘化钾、淀粉的显色反应 ,建立了碘化钾碘兰分光光度法测定微量过氧化氢方法。过氧化氢浓度在 0～ 2 5μg/2 5m L范围内有良好的线性关系 ,方法的相对标准偏差 1 .2 % ,回收率 97.2 %～1 0 1 .2 % ,检出限为 2 .0× 1 0 -3 mg/L。并应用于雨水、空气中微量过氧化氢的测定。     

Trace analysis of airborne 1,6-hexamethylenediisocyanate and the related aminoisocyanate and diamine by glass capillary gas chromatography

A capillary gas chromatographic method was developed for the analysis of complex air mixtures of 1,6-hexamethylenediisocyanate, 1,6-hexamethyleneaminoisocyanate and 1,6-hexamethylenediamine. The method is based on derivatization in the sampling step of the reactive isocyanate groups to corresponding urethane groups by the alkaline ethanolic solvent and a subsequent derivatization of remaining amino groups to amide groups with heptafluorobutyric acid anhydride. The overall procedure, including sampling, gave a linear response at air concentrations of 3-300 micrograms/m3 for 1,6-hexamethylenediisocyanate with a precision of ca. 4% at 15 micrograms/m3 and a detection limit of ca. 0.2 microgram/m3 using nitrogen selective detection. In a field measurement of air concentrations in welding work on lacquered metal parts at a motor-car workshop, concentrations of 1,6-hexamethylenediisocyanate above 600 micrograms/m3 were found. Also 1,6-hexamethyleneaminoisocyanate and 1,6-hexamethylenediamine were found at concentrations of the order of 15% of the 1,6-hexamethylenediisocyanate concentration.     

Liquid chromatographic/electrospray ionization tandem mass spectrometric analysis for the quantification of buprenorphine, norbuprenorphine, buprenorphine-3-beta-D-glucuronide and norbuprenorphine-3-beta-D-glucuronide in human plasma

A liquid chromatographic/electrospray ionization tandem mass spectrometric method for the quantification of the synthetic opiate buprenorphine (BUP), norbuprenorphine (NBUP), buprenorphine-3-beta-D-glucuronide (BUP-3-G) and norbuprenorphine-3-beta-D-glucuronide (NBUP-3-G) in human plasma was developed and validated. Identification and quantification were based on the following transitions: m/z 468 to 396 and 414 for BUP, m/z 414 to 326 and 340 for NBUP, m/z 644 to 468 for BUP-3-G and m/z 590 to 414 for NBUP-3-G. Calibration by linear regression analysis utilized deuteratated internal standards and a weighting factor of 1/x. The method was accurate and precise across a linear dynamic range of 0.6-50.0 ng ml(-1). Pretreatment of plasma samples using solid-phase extraction was sufficient to limit matrix suppression to <30% for all four analytes. The method proved to be suitable for the quantification of BUP and the related metabolites in plasma samples collected from BUP-maintained study participants.     

Application of a metallized membrane electrode for the determination of gaseous sulphur compounds after reductive pyrolysis

Sulphur-containing gases are converted by non-catalytic reductive pyrolysis into an equivalent amount of H(2)S, which is determined by electrochemical oxidation at a gold-plated porous membrane electrode. The calibration for H(2)S is linear up to 18 ml/m(3) with a slope of 1.12 muA.m(3).ml(-1). The relative standard deviation for the determination of 3.7 ml/m(3) H(2)S was 1.0% and the detection limit 4 mul/m. About 60 samples can be determined per hour. The method has been employed for the determination of total sulphur and individual gases after separation on a chromatographic column.     

Determination of hexahydrophthalic anhydride in air using gas chromatography.

Two methods for the determination of hexahydrophthalic anhydride (HHPA) in air were developed. In a solid sorbent method, HHPA was sampled in Amberlite XAD-2 tubes, eluted in toluene and analysed by gas chromatography with flame ionization detection. The sampling rates were 0.2 and 1.0 l/min. At 15 micrograms/m3 (relative humidity less than 2%) and 27 micrograms/m3 (relative humidity 70%) no breakthrough was observed. However, at 160 micrograms/m3 (relative humidity less than 2%), 6% breakthrough was found. The sampling efficiency of the sampling rates 0.2 and 1.0 l/min did not differ. In a bubbler method, HHPA was sampled in bubblers filled with 0.1 M sodium hydroxide solution. The sodium salt of hexahydrophthalic acid was formed. No breakthrough was observed using a sampling rate of 1.0 l/min. The samples were stable during storage for eight weeks in a refrigerator. The HHP acid was esterified with methanol-boron trifluoride and analysed by gas chromatography-flame ionization detection. Apparatus for the generation of standard atmospheres of HHPA, in the range of 10-3000 micrograms/m3, was developed using the diffusion principle. For the solid sorbent method the precision (coefficient of variation) of the overall method was 2-7%, and for the bubbler method 3-19% (range 15-160 micrograms HHPA/m3; relative humidity = less than 2-70%). A comparison between the two methods was performed using the standard atmosphere. The concentrations found by the solid sorbent method were 86-98% of those found by the bubbler method (range 15-160 micrograms HHPA per m3; relative humidity = less than 2-70%). In work environment air, 93% was found using the solid sorbent method relative to the bubbler method at a mean concentration of 330 micrograms/m3 (coefficient of variation = 39%; range 200-540 micrograms/m3). For both methods, concentrations greater than 3 micrograms/m3 could be quantified at 60 min sampling with a sampling rate of 1.0 l/min.     

MS3 using the collision cell of a tandem mass spectrometer system

We report the feasibility of multistage fragmentation in combination with a fast background subtraction method, yielding the equivalent of MS3. The first quadrupole selects an ion of interest, and the ion is axially accelerated into Q2 to generate fragment ions. Subsequent stages of mass selection and fragmentation are obtained by quadrupolar resonant excitation within the Q2 collision cell. The fragments are analyzed downstream by either a resolving quadrupole or a time-of-flight (TOF) mass spectrometer, and multistage spectra are obtained by subtraction (MS(n) - MS(n-1)) for n = 3 or 4. We discuss the characterization of this method, including product ion arrival times, fragmentation efficiencies, and ion selectivity. We report accurate TOF mass spectra of background-subtracted MS3 for protonated molecules reserpine (m/z 609), bosentan (m/z 1552), and taxol (m/z 854).     

催化发光法同时测定空气中的甲醛、苯和二氧化硫

基于甲醛、苯和二氧化硫在纳米Ti3CeY2O11上的催化发光有交叉敏感现象,在3个波长处分别确定甲醛、苯和二氧化硫浓度与催化发光信号强度的响应关系,再依据发光信号强度的叠加性特征即可获取甲醛、苯和二氧化硫的准确浓度,据此建立了同时测定空气中甲醛、苯和二氧化硫的新方法.3个分析波长分别为420、535和680 nm,敏感材料表面温度为280℃,载气流速为130 mL/min.本方法对甲醛、苯和二氧化硫的检出限(3σ)分别为0.04、0.05和0.10 mg/m3,线性范围分别为0.08~75.60 mg/m3、0.10~101.40 mg/m3和0.30~115.00 mg/m3, 回收率分别为96.4%~103.7%、97.8%~102.5%和97.2%~103.3%.常见共存物,如乙醛、甲苯、硫化氢、氨、甲醇、乙醇和二氧化碳等不干扰测定.连续200 h通浓度均为50 mg/m3的甲醛、苯和二氧化硫混合气体,发光强度的相对偏差≤2%,表明此纳米级复合氧化物对甲醛、苯和二氧化硫的敏感性的寿命长.本方法充分利用了交叉敏感现象,可以实现空气中甲醛、苯和二氧化硫的在线分析.     

Evaluation of solid-phase micro-extraction coupled to gas chromatography-mass spectrometry for the headspace analysis of volatile compounds in cocoa products

The aroma profile of cocoa products was investigated by headspace solid-phase micro-extraction (HS-SPME) combined with gas chromatography–mass spectrometry (GC–MS). SPME fibers coated with 100 μm polydimethylsiloxane coating (PDMS), 65 μm polydimethylsiloxane/divinylbenzene coating (PDMS-DVB), 75 μm carboxen/polydimethylsiloxane coating (CAR-PDMS) and 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane on a StableFlex fiber (DVB/CAR-PDMS) were evaluated. Several extraction times and temperature conditions were also tested to achieve optimum recovery. Suspensions of the samples in distilled water or in brine (25% NaCl in distilled water) were investigated to examine their effect on the composition of the headspace. The SPME fiber coated with 50/30 μm DVB/CAR-PDMS afforded the highest extraction efficiency, particularly when the samples were extracted at 60 °C for 15 min under dry conditions with toluene as an internal standard. Forty-five compounds were extracted and tentatively identified, most of which have previously been reported as odor-active compounds. The method developed allows sensitive and representative analysis of cocoa products with high reproducibility. Further research is ongoing to study chocolate making processes using this method for the quantitative analysis of volatile compounds contributing to the flavor/odor profile.     

环五甲撑五硝胺(CRX)结构和性质的DFT预示

用密度泛函理论(DFT)B3LYP方法,在6-31G*基组水平下,全优化计算了环五甲撑五硝胺(CRX)的分子几何和优化构型下的电子结构.环C-N键长为0.144～0.148 nm, N-NO2键长为0.139～0.142 nm; CRX的最高占有MO(HOMO)能级和最低未占MO(LUMO)能级之间的差值ΔEg(5.2054 eV)较大,预示CRX较稳定.基于简谐振动分析求得IR谱频率和强度.运用统计热力学方法,求得在200～1200 K的热力学性质C0p,m、 S0m和H0m.还运用Kamlet公式预示了它的爆速和爆压分别为9169 m/s和37.88 GPa.     

Development and validation of a capillary high-performance liquid chromatography/electrospray tandem mass spectrometric method for the quantification of bisphenol A in air samples

Bisphenol A (BPA) is a toxic industrial chemical that affects the endocrine system even at low concentrations. A new method, based on capillary high-performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC/ESI-MS/MS) analysis, has been developed to determine BPA in atmospheric samples. The method involves collection of air samples (typically 2 m(3)) on glass fiber filters, with ultrasonic extraction and sample concentration under vacuum before analysis. HPLC analysis was performed isocratically at a flow rate of 10 microL min(-1) using a capillary reversed-phase column and MS/MS analysis in negative ion multiple reaction monitoring (MRM) mode, using BPA-d(16) as internal standard. The present method provides linear response in the range 0.007-3.5 microg/filter (R(2) > 0.999) and is characterized by high accuracy (mean bias 2%) and good reproducibility (mean RSD 5%). High sensitivity (LOD = 2 ng/m(3) based on 2 m(3) of air collected), specificity, and speed of the analysis make the present method suitable for routine determination of BPA in the atmosphere, both for ambient and personnel monitoring.     

气相色谱法快速测定空气中低分子量醛

用填充气相色谱直接进样法测定了污染空气中甲醛、乙醛、丙醛的含量,并对方法的灵敏度、准确度及各种影响因素进行了探讨。方法用于样品测定取得了较为满意的结果。