Fabrication and anti‐corrosion property of superhydrophobic hybrid film on copper surface and its formation mechanism

Compact and uniform superhydrophobic films were prepared on copper substrates using one‐step solution‐immersion process, and the appropriate preparation conditions were selected for mixed solutions. SEM shows that the hybrid film of 1‐dodecanethiol and tetradecanoic acid on copper substrate is more compact with the contact angle of 160°. The electrochemical impedance spectroscopy and polarization test demonstrate that the anti‐corrosion property of surface‐modified copper substrate is greatly improved, especially for the hybrid film. Moreover, the competitive adsorption process and adsorptive geometry of hybrid film were well explained based on the results of quantum chemistry calculations, SEM, and energy dispersive X‐ray analysis. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of a superhydrophobic rough surface

The relationship between the contact angles, surface tension, and surface roughness is reviewed. Numerical formulas related to the superhydrophobic rough surfaces of polymers are predicted with two approaches, the Wenzel and Cassie–Baxter models. With these models as a guide, an artificial superhydrophobic surface is created. Rough nylon surfaces mimicking the lotus leaf are created by the coating of a polyester surface with nylon‐6,6 short fibers via the flocking process. Poly(acrylic acid) chains aregrafted onto nylon‐6,6 surfaces, and this is followed by the grafting of 1H,1H‐perfluorooctylamine onto the poly(acrylic acid) chains. Water contact angles as high as 178° are achieved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 253–261, 2007.     

Characterisation of microstructure and evaluation of optical and EPR properties of superhydrophobic copper dodecanoate films

Copper dodecanoate films prepared by emulsion method exhibit superhydrophobic property with water contact angle of 155° and sliding angle of <2°. The films have been characterised by using X‐ray diffraction, field emission scanning electron microscopy and Fourier transform infrared spectroscopy techniques. Surface microstructure of copper dodecanoate consists of numerous microscale papillas of about 6–12 µm in length with a diameter in the range of 360–700 nm. The superhydrophobicity of the films is due to their dual micronano surface morphology. The wetting behaviour of the film surface was studied by a simple water immersion test. The results show that copper dodecanoate film retained superhydrophobic property even after immersing in water for about 140 h. The optical absorption spectrum exhibits two broadbands centred at 388 and 630 nm that have been assigned to ²B_1g → ²E_g and ²B_1g → ²B_2g transitions of Cu²⁺ ions, respectively. The electron paramagnetic resonance spectrum exhibits two resonance signals with effective g values at g_|| ≈ 2.308 and g_⊥ ≈ 2.071, which suggests that the unpaired electron occupies d_x2–y2 orbital in the ground state. Copyright © 2011 John Wiley & Sons, Ltd.     

Facile fabrication of a superhydrophobic surface from natural Eucommia rubber

In this study, we introduce a fabrication method for a superhydrophobic surface made from natural Eucommia rubber. Based on the Eucommia rubber extract solution, we prepared a type of superhydrophobic material using the simple phase separation method and the addition of a low‐surface‐energy substance method, thus developing a new approach for the application of natural Eucommia rubber. The experimental results showed that a superhydrophobic film could be obtained by both the addition of acetone and induction by water vapor. Additionally, the film exhibited properties closely related to the crystalline Eucommia rubber spherical particles with a hierarchical structure. The addition of hydrophobic silica also increased the hydrophobic property of the Eucommia rubber film. When the content of the silica was 4% (wt%), the contact angle of the composite film reached 160.7°, which could be attributed to the properties of the nano‐silica and the micro‐nano structure of the composites. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence of bath temperatures on the wettability of copper films surface prepared by electroless plating method on beech wood

Copper films were coated on beech wood substrates by electroless plating method. The influence of bath temperature on the copper films properties was studied by varying the bath temperatures 25, 35, 45 and 55 °C. Scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), X‐ray diffraction (XRD) pattern, X‐ray photoelectron spectroscopy (XPS), micro Raman spectroscopy and contact angle measurements were used to both characterize the physical and chemical copper films properties and understand the influence of bath temperature on the wettability of copper surface. In our studies, we have found that the gained copper mass significantly increased at 55 °C. The crystalline nature of the coated copper was confirmed by XRD. The presence of Cu₂O and CuO was observed by XPS and micro Raman techniques, which confirms the oxidization of the coated copper surface. Also these characterization techniques have shown the big influence of bath temperature on the morphology, grain size, chemical composition and the film thickness of the coated copper. The wettability was highly influenced by increasing CuO on the coated copper, which is increased by the bath temperature. The contact angle measurements have demonstrated the influence of C―O, O―C?O and CuO components of the surface on the wettability of the samples. Copyright © 2016 John Wiley & Sons, Ltd.     

Fabrication of functionalized aluminum compound petallike structure with superhydrophobic surface

The petallike structures, similar to that of a lotus leaf, were directly fabricated on the surface of aluminum sheets by a simple one‐step solution‐immersion process. It was found that the width of the nanoflakes ranges from 20 to 500 nm, and the length of the flakes is about several micrometers. The wettability of the surface with a hierarchical structure was changed from superhydrophilicity to superhydrophobicity by chemical modification with perfluorodecyltriethoxysilane (PDES). The static contact angles (CAs) for water on both of the modified surfaces were larger than 150° , which was closely related to the chemical modification and hierarchical structure. Furthermore, the surfaces retained good superhydrophobic stability in long‐term storage as well, which should be critical to the application of aluminum materials in engineering. Copyright © 2010 John Wiley & Sons, Ltd.     

超疏水表面研究进展

综述了超疏水表面研究进展,简述了超疏水表面研究的理论基础,归纳总结了超疏水表面的制备方法及存在的问题,并介绍了功能超疏水材料研究的最新进展.指出超疏水表面因其独特的自清洁性能而成为功能材料及表面界面科学领域的研究热点之一,并就其今后的发展进行了展望.     

SiC表面Ni沉积超疏水膜层的形成机理

前期采用环境友好方法制备的改性碳化硅颗粒,经较长时间放置,发现其由亲水性转变为超疏水性,接触角为156°。为解释这一新的现象,采用扫描电子显微镜、能谱、(高分辨)透射电子显微镜、X射线光电子能谱(XPS)对原粉碳化硅、改性后碳化硅及久置碳化硅进行了测试与分析。结果显示：改性后碳化硅经较长时间放置,表面胞状颗粒增大并出现凸起物,粗糙度增加,存在类似于荷叶的微纳米结构。改性后颗粒的主要成分为Ni、Si、O,其中凸起处Ni、O元素的含量明显高于凹陷处。Ni颗粒表面出现清晰的膜层,膜层厚度为2～3 nm,但结晶度偏低。XPS测试结果显示金属镍的特征峰正向移动近4 eV,与镍的氧化态特征峰相一致,从而解释了颗粒表面形态发生细小改变,自发形成超疏水膜层的机理。     

SiC表面Ni沉积超疏水膜层的形成机理

前期采用环境友好方法制备的改性碳化硅颗粒,经较长时间放置,发现其由亲水性转变为超疏水性,接触角为156°。为解释这一新的现象,采用扫描电子显微镜、能谱、(高分辨)透射电子显微镜、X射线光电子能谱(XPS)对原粉碳化硅、改性后碳化硅及久置碳化硅进行了测试与分析。结果显示：改性后碳化硅经较长时间放置,表面胞状颗粒增大并出现凸起物,粗糙度增加,存在类似于荷叶的微纳米结构。改性后颗粒的主要成分为Ni、Si、O,其中凸起处Ni、O元素的含量明显高于凹陷处。Ni颗粒表面出现清晰的膜层,膜层厚度为2~3 nm,但结晶度偏低。XPS测试结果显示金属镍的特征峰正向移动近4eV,与镍的氧化态特征峰相一致,从而解释了颗粒表面形态发生细小改变,自发形成超疏水膜层的机理。     

Electropolymerization of DBSA‐doped polypyrrole films on PTFE via an electroless copper interlayer

We report on the electroless deposition of thin films of copper on poly(tetrafluoroethylene) (PTFE) and their use as substrates for electropolymerization of polypyrrole. Argon plasma‐treated PTFE films were modified by silanization using N‐[3(trimethoxysilyl)propyl]diethylenetriamine (TMS). The TMS‐modified PTFE films were subsequently activated by PdCl₂ for the electroless deposition of copper. The omission of the commonly used SnCl₂ sensitization step represents a significant process enhancement with environmental and cost benefits. The surface composition of the substrate (before and after surface treatments) and overlayer films was studied using high‐resolution x‐ray photoelectron spectroscopy. A combination of time‐of‐flight secondary ion mass spectrometry and water contact‐angle measurements was also used to study the PTFE surface after argon plasma treatment. The Cu/PTFE films were used as substrates for subsequent pyrrole electropolymerization in aqueous dodecylbenzene sulphonic acid (DBSA) solution. The DBSA‐doped polypyrrole overlayers were successfully deposited on the Cu/PTFE surface using a constant applied potential of 1.5 V. The resulting material exhibited a doping level of 39%, determined using chemical component analysis of the N 1s photoelectron peak. Copyright © 2003 John Wiley & Sons, Ltd.     

2,2''''-联吡啶和亚铁氰化钾对乙醛酸化学镀铜的影响

以乙醛酸作还原剂、Na2EDTA为络合剂、2,2'-联吡啶和亚铁氰化钾作为添加剂组成化学镀铜体系,研究了两种添加剂对化学镀铜速率、镀层表面形貌、组成和结构的影响.结果表明:添加适量的2,2'-联吡啶和亚铁氰化钾,不仅提高了镀液的稳定性,而且使沉积速率增加1倍.这两种添加剂的同时使用,使镀层颜色变亮,形貌发生变化.所得镀层是多晶铜,没有发现夹杂Cu20.     

The superhydrophobic properties of ZrO2 induced by laser irradiation

The stable superhydrophobic surface of the ZrO₂ substrate could be conveniently and rapidly prepared by KrF laser irradiation. With different laser energy density, the static water contact angle (CA) increased from 72° to approximately 151°. It was found that the formation of micro–nano fluctuant geometry surface structure was the dominant factor to the hydrophobic property after laser irradiation. When the laser‐irradiated sample annealed at O₂ atmosphere, formation of oxygen‐related defects with high surface free energy could make the CA decrease abruptly at the beginning. After being stored at ambient atmosphere, the CA would reconvert to the value of the freshly irradiated sample gradually. Copyright © 2012 John Wiley & Sons, Ltd.     

2,2′-联吡啶和亚铁氰化钾对乙醛酸化学镀铜的影响

以乙醛酸作还原剂、Na2EDTA为络合剂、2,2′-联吡啶和亚铁氰化钾作为添加剂组成化学镀铜体系,研究了两种添加剂对化学镀铜速率、镀层表面形貌、组成和结构的影响.结果表明:添加适量的2,2′-联吡啶和亚铁氰化钾,不仅提高了镀液的稳定性,而且使沉积速率增加1倍.这两种添加剂的同时使用,使镀层颜色变亮,形貌发生变化.所得镀层是多晶铜,没有发现夹杂Cu2O.     

Effect of surface morphology on measurement and interpretation of boundary slip on superhydrophobic surfaces

Highly liquid repellent surfaces have been obtained by the combination of roughness and hydrophobicity. Studies have reported that the flow over such surfaces exhibits larger boundary slip as compared to the smooth hydrophobic surfaces. However, the surface roughness can also lead to apparent slip. Thus, the effect of the two factors, that is, wettability and roughness, needs to be segregated. In this study, we have measured the slippage of water on rough hydrophilic and hydrophobic surfaces using colloidal probe atomic force microscopy technique (CP‐AFM). Results showed that the effect of surface roughness on the measured slip is dominant over that of wettability. It was also found that slip on surfaces with sparsely distributed asperities is highly local and measurements on various locations give dissimilar results. The results suggested that the main reason of the larger slip, on rough hydrophobic surfaces, is likely to be the roughness and not the hydrophobicity. Moreover, it was also found that the slip does not vary considerably with the increase or decrease in the shear rate. Most likely, this kind of slip phenomena is caused by the apparent decrease of the drag force, because the nanoasperities on the surface restrict the probe from reaching the surface properly. Copyright © 2016 John Wiley & Sons, Ltd.     

Investigation on surface properties of superhydrophobic nanocomposites based on polyvinyl chloride and correlation with cell adhesion behavior

The main aim was to study the roles of structural homogeneity and superhydrophobicity on the adhesion of SW colon cancer cells on the surface of polyvinyl chloride (PVC) nanocomposites. Concurrent use of a proper nonsolvent (ethanol) and silica nanoparticles resulted in superhydrophobic behavior and also different surface structures. The effect of added‐ethanol content on the surface properties of PVC nanocomposites was also studied. The synergetic combination of silica and ethanol has led to the formation of a porous surface layer resulting in a considerable boost in the hydrophobic behavior. The scanning electron microscopy, roughness, and X‐ray photoelectron spectroscopy (XPS) analysis results were all in total agreement indicating the substantial change in surface morphology, topography, and composition once the ethanol content was increased to 50 vol.%. The surface structure was notably changed by the addition of polyhedral oligomeric silsesquioxanes (POSS) nanoparticles. It was found that the induced inhomogeneity as a result of POSS addition had an adverse effect on the surface properties. In conclusion, superhydrophobicity could be regarded as a prerequisite for achieving cell‐repellent behavior, but it cannot guarantee a cell repellent surface especially if the surface layer possesses structural inhomogeneity.     

Novel Electroless Deposition of Cu<Subscript>3</Subscript>Se<Subscript>2</Subscript> Film on Silicon Substrate by a Simple Galvanic Displacement Process

A novel electroless deposition method for depositing highly uniform adhesive thin films of copper selenide (Cu₃Se₂) on silicon substrates from aqueous solutions is described. The deposition is carried out by two coupled galvanic reactions in a single deposition bath containing copper cations, hydrogen fluoride, and selenous acid: the galvanic deposition of copper on silicon and the subsequent galvanic reaction between the deposited copper with selenous acid in the deposition bath. The powder X-ray diffraction and scanning electron microscopy are used to characterize and examine the deposited films.     

Designing superhydrophobic surface based on fluoropolymer–silica nanocomposite via RAFT‐mediated polymerization‐induced self‐assembly

Superhydrophobic surfaces (SHS) find versatile applications as coatings due to their very high water‐repellency, self‐cleaning, and anti‐icing properties. This investigation describes the preparation of a SHS from surfactant‐free hybrid fluoropolymer latex. In this case, reversible addition‐fragmentation chain transfer (RAFT) polymerization was adopted to prepare a copolymer of 4‐vinyl pyridine (4VP) and vinyl triethoxysilane (VTES), where the pyridine units were quaternized to make the copolymer soluble in water. The copolymer was further used as a macro‐RAFT agent to polymerize 2,2,2‐trifluoroethyl methacrylate (TFEMA) in a surfactant‐free emulsion via polymerization‐induced self‐assembly (PISA). The macro‐RAFT agent contained a small amount of VTES as co‐monomer which was utilized to graft silica nanoparticles (SNPs) onto the P(TFEMA) spheres. The film prepared using the nanocomposite latex exhibited a nano‐structured surface as observed by SEM and AFM analyses. Surface modification of the film with fluorinated trichlorosilane produced an SHS with a water contact angle (WCA) of 151.5°. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 266–275