Effect of cold atmospheric plasma treatment on hydrophilic properties of fluorosilicone rubber

Vulcanized fluorosilicone rubber for aviation was treated by argon and oxygen cold atmospheric plasma (CAP) in order to modify its hydrophilic properties. The sample's chemical composition was analyzed by X‐ray photoelectron spectroscopy (XPS). The static contact angle, surface free energy, and adhesion strength were used to indicate the hydrophilic properties. Additionally, the surface morphologies of the specimens were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results showed that the contact angle declined from 101.5° to 22°, and the surface energy rose from 21.3 to 71.2 mJ/m² after they were treated by argon plasma. Alternatively, the water contact angle decreased to 25.5°, and the surface energy increased to 70.6 mJ/m² after they were treated by oxygen plasma. In addition, the SEM and AFM images of the samples illustrate that the treated surface of fluorosilicone rubber becomes rougher than the non‐treated surface. The concentrations of carbon (C) and fluorine (F) elements of the material' surface decreased and the contents of O element greatly enriched after plasma treatment. Additionally, chemical group C―O and C―OH appeared after the treatment. However, the hydrophilic effect of the plasma treatment is aged after the specimens were stored for 8–12 h. Copyright © 2016 John Wiley & Sons, Ltd.     

Surface roughness and hydrophilicity enhancement of polyolefin‐based membranes by three kinds of plasma methods

The introduction of antibacterial property, conductivity, wettability and antithrombogenicity into polyolefin‐based membranes has evoked much attention, which can be achieved by coating hydrophilic polymers. Therefore, it is necessary to modify the roughness and hydrophilicity of polyolefin‐based membranes to enhance the coating ability. In this paper, three kinds of plasma methods, including inductively coupled (ICP) plasma, radio frequency low pressure (RFP) plasma and atmospheric dielectric barrier discharge (DBD) plasma, were used to modify the surface of the polyethylene (PE), polypropylene (PP) and polyester‐polypropylene (PET–PP) membranes. The surface roughness of the plasma‐modified PE, PP and PET–PP films was investigated by scanning electron microscopy (SEM) and atomic force microscope (AFM). The polar functional groups of films were observed by energy dispersive spectrometer (EDX) and X‐ray photoelectron spectroscopy (XPS). Besides, the hydrophilicity of the plasma‐modified PE, PP and PET–PP films was evaluated by water contact angle measurement. It was found that the surface roughness and hydrophilicity of plasma‐modified PE, PP and PET–PP films increased with the generation of oxygen‐containing functional groups (i.e. C―O, and C?O). The PET–PP membranes were treated by RFP plasma at different processing powers and times. These results indicated that plasma is an effective way to modify films, and the treatment time and power of plasma had a certain accumulation effect on the membranes' hydrophilicity. As for the roughness and hydrophilicity, the DBD plasma modifies the PE film, which is the optimum way to get the ideal roughness and hydrophilicity. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface modification of plasma‐pretreated expanded poly (tetrafluroethylene) films by graft copolymerization

A two‐step process based on a low‐pressure helium plasma treatment followed by acrylic acid‐grafting copolymerization was used for the surface modification of expanded polytetrafluoroethylene (ePTFE) films. The effects of plasma treatment power and treatment time on the hydrophilicity of the film surface were investigated. The wettability of the ePTFE film surface was characterized by water contact angle, and the surface compositions of the untreated and treated ePTFE samples were evaluated by atomic force microscopy and XPS. Contact angle measurements revealed that the hydrophilicity of the ePTFE film surface was greatly enhanced by the combined actions of the plasma treatment and acrylic acid grafting, and the contact angle decreased from 145° to 66°. Atomic force microscopy analyses showed that the surface roughness increased after the plasma treatment. XPS analyses showed substantial increase in the concentration of carbon and oxygen atoms and a decrease in the concentration of fluorine atoms at the film surface. T‐peel strength showed an improved bonding strength between the film and an adhesive tape after the treatment. Copyright © 2012 John Wiley & Sons, Ltd.     

Surface modification of PVC endotracheal tubes by oxygen glow discharge to reduce bacterial adhesion

A d.c. oxygen glow discharge was used to modify medical‐grade poly(vinyl chloride) (PVC) to study how surface chemistry and hydrophilicity influence Pseudomonas aeruginosa adhesion. The effects of plasma exposure time on the resulting surface, including chemical composition, wettability and roughness, were assessed using x‐ray photoelectron spectroscopy, contact angle measurements and atomic force microscopy analysis. A significant alteration in the hydrophilicity of the native PVC surface was observed after oxygen glow discharge treatment. The water contact angle decreased from ～80° to 8–20°, with a weak dependence of the exposure time used. The change in surface wettability resulted from the incorporation of oxygenated functional groups, including esters, ketones and acids, as indicated by XPS analysis. The amount of oxygen incorporation was shown to be essentially independent of plasma exposure time. However, prolonged plasma exposure resulted in increased surface roughness. Bacterial adhesion efficiency was evaluated for PVC modified by 120 s of plasma exposure, because this exposure time was determined to yield the maximum decrease in contact angle. Oxygen plasma treatment of native PVC was found to yield a 70% reduction in bacterial adhesion for the four strains of Pseudomonas aeruginosa tested. Copyright © 2003 John Wiley & Sons, Ltd.     

Surface modification of a liquid‐crystalline polymer for copper metallization

The effects of different surface modifications on the adhesion of copper to a liquid‐crystalline polymer (LCP) were investigated with X‐ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, contact‐angle measurements, and pull tests. High pull‐strength values were achieved when copper was sputter‐deposited onto plasma and reactive‐ion‐etching (RIE)‐pretreated LCP surfaces. The values were comparable to the reference pull strengths obtained with laminated copper on the LCP. The adhesion was relatively insensitive to the employed feed gas in the pretreatments. The surface characterizations revealed that for RIE and plasma treatments, the enhanced adhesion was attributable to the synergistic effects of the increased surface roughness and polar component of the surface free energy of the polymer. However, if the electroless copper deposition was performed on RIE‐ or plasma‐treated surfaces, very poor adhesion was measured. Good adhesion between the LCP substrate and electrolessly deposited copper was achieved only in the case of wet‐chemical surface roughening as a result of the creation of a sufficient number of mechanical interlocking sites, together with a significant loss of oxygen functionalities, on the surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 623–636, 2003     

Surface characterization and radical decay studies of oxygen plasma‐treated PMMA films

Polymethylmethacrylate (PMMA) films were modified by RF oxygen plasma with various powers applied for different periods, and the effects of these parameters on the surface properties such as hydrophilicity, surface free energy (SFE), chemistry, and topography were investigated by water contact angle, goniometer, X‐ray photoelectron spectroscopy (XPS), and atomic force microscopy, and the types of the created free radicals and their decay were detected by electron spin resonance spectroscopy (ESR). SFE and contact angle results varied depending on the plasma parameters. Oxygen plasma treatment (100 W–30 min) enhanced the hydrophilicity of PMMA surface as shown by decreasing the water contact angle from 70° to 26°. XPS analysis showed the change in the amounts of the present functionalities as well as formation of new groups as free carbonyl and carbonate groups. The roughness of the surface increased considerably from ~2 nm to ~75 nm after 100 W–30 min oxygen plasma treatment. ESR analysis indicated the introduction of peroxy radicals by oxygen plasma treatment, and the intensity of the radicals increased with increasing the applied power. Significant decrease in radical concentration was observed especially for the samples treated with higher powers when the samples were kept under the atmospheric conditions. As a conclusion, RF plasma, causes changes in the chemical and physical properties of the materials depending on the applied parameters, and can be used for the creation of specific groups or radicals to link or immobilize active molecules onto the surface of a material. Copyright © 2012 John Wiley & Sons, Ltd.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

Solid‐state bonding of silicone elastomer to glass by vacuum oxygen plasma,atmospheric plasma,and vacuum ultraviolet light treatment

We experimentally demonstrated that treating a silicone elastomer by a vacuum oxygen plasma, an atmospheric pressure plasma, and vacuum ultraviolet (VUV) radiation resulted in different surface modifications that gave different contact angles, contact angle aging, and bond strengths. The aim of this study was to assess whether high‐throughput surface modification techniques of atmospheric pressure plasma and VUV radiation have the potential to replace conventional oxygen plasma modification. Four silicone elastomers with different hardnesses were used as specimens. The surfaces of all four silicone elastomers were successfully modified from hydrophobic to hydrophilic and they were also bonded to glass surfaces by the three surface modification techniques, although considerable variations were observed in the surface hydrophobicity and the bonding properties. The results clearly reveal that atmospheric pressure plasma and VUV treatment have the potential to replace conventional oxygen plasma treatment. In particular, VUV irradiation produced the most hydrophilic surface that was preserved for a long time. Thus, VUV irradiation is the most promising technique for realizing high‐throughput surface modification and bonding of silicone elastomers. Copyright © 2012 John Wiley & Sons, Ltd.     

Nanodrop on a nanorough solid surface: density functional theory considerations

The density distributions and contact angles of liquid nanodrops on nanorough solid surfaces are determined on the basis of a nonlocal density functional theory. Two kinds of roughness, chemical and physical, are examined. The former considers the substrate as a sequence of two kinds of semi-infinite vertical plates of equal thicknesses but of different natures with different strengths for the liquid-solid interactions. The physical roughness involves an ordered set of pillars on a flat homogeneous surface. Both hydrophobic and hydrophilic surfaces were considered. For the chemical roughness, the contact angle which the drop makes with the flat surface increases when the strength of the liquid-solid interaction for one kind of plates decreases with respect to the fixed value of the other kind of plates. Such a behavior is in agreement with the Cassie-Baxter expression derived from macroscopic considerations. For the physical roughness on a hydrophobic surface, the contact angle which a drop makes with the plane containing the tops of the pillars increases with increasing roughness. Such a behavior is consistent with the Wenzel formula developed for macroscopic drops. For hydrophilic surfaces, as the roughness increases the contact angle first increases, in contradiction with the Wenzel formula, which predicts for hydrophilic surfaces a decrease of the contact angle with increasing roughness. However, a further increase in roughness changes nonmonotonously the contact angle, and at some roughness, the drop disappears and only a liquid film is present on the surface. It was also found that the contact angle has a periodic dependence on the volume of the drop.     

Plasma surface modification of chitosan membranes: characterization and preliminary cell response studies

Surface modification of biomaterials is a way to tailor cell responses whilst retaining the bulk properties. In this work, chitosan membranes were prepared by solvent casting and treated with nitrogen or argon plasma at 20 W for 10-40 min. AFM indicated an increase in the surface roughness as a result of the ongoing etching process. XPS and contact angle measurements showed different surface elemental compositions and higher surface free energy. The MTS test and direct contact assays with an L929 fibroblast cell line indicated that the plasma treatment improved the cell adhesion and proliferation. Overall, the results demonstrated that such plasma treatments could significantly improve the biocompatibility of chitosan membranes and thus improve their potential in wound dressings and tissue engineering applications.     

Surface characteristic of poly(p‐phenylene terephthalamide) fibers with oxygen plasma treatment

Oxygen plasma is widely employed for modification of polymer surfaces. Plasma treatment process is a convenient procedure that is also environmentally friendly. This study reports the effects of oxygen plasma treatment on the surface properties of poly(p‐phenylene terephthalamide) (PPTA) fibers. The surface characteristics before and after oxygen plasma treatment were analyzed by XPS, atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA). It was found that oxygen plasma treatment introduced some new polar groups (O? C?O) on the fiber surface, increased the fiber surface roughness and changed the surface morphologies obviously by plasma etching and oxidative reactions. It is also shown that the fiber surface wettability was improved significantly by oxygen plasma treatment. Copyright © 2008 John Wiley & Sons, Ltd.     

Reverse hydrophobic PDMS surface to hydrophilic by 1‐step hydrolysis reaction

Hydrophilic modification on the surface of polymer polydimethylsiloxane (PDMS) material is a key step for its application in biomaterial, bioengineering, and so on. In this article, a novel and effective method was proposed to reverse hydrophobic surface to hydrophilic by 1‐step hydrolysis of Si―O bond to produce hydrophilic hydroxyl group. The hydrophilizing reagent 2‐(trimethylsiloxy) ethyl methacrylate (TMSEMA) was used during the copolymerization of polydimethylsiloxane prepolymer (DMS U21). The prepared PDMS film was subjected to 1‐step surface hydrophilic reversal treatment using KOH solution to produce hydroxyl groups on the surface. The contact angle, attenuated total reflection Fourier transform infrared spectra, and equilibrium water content (EWC) measurements were conducted on PDMS films. The results showed that TMSEMA content had no obvious impact on the contact angle and EWC value of untreated PDMS. After reversal treatment, the contact angle decreased from 94° to 15°, and the EWC value increases to 10% when the TMSEMA content was 15 wt%. The spectrum proved that the reverse reaction produced hydroxyl and carboxylate on the surface. The hydrophilic stability, surface morphology, and protein adsorption properties of PDMS film were also investigated. This study can provide new ideas and further reference for improving the hydrophilicity of PDMS surface.     

Wettability of poly(styrene‐co‐acrylate) ionomers improved by oxygen‐plasma source ion implantation

The surfaces of poly(styrene‐co‐acrylic acid) copolymers and their Na‐ and Cs‐neutralized ionomers were modified by O₂‐plasma source ion implantation (PSII) treatment to improve the surface wettability. The changes in the surface wettability, composition, and structure upon the PSII treatment were examined with contact‐angle measurements and X‐ray photoelectron spectroscopy. The untreated surfaces of the acid copolymers and ionomers exhibited different surface energies; this implied clearly that the type of ion species affects the surface hydrophilicity. Also, the PSII treatment induced oxygen‐containing groups to reside on the surface and ionic groups to come out toward the surface; this made the surfaces of the ionomers more hydrophilic as compared with that of the acid copolymers. The ionomers also showed slow hydrophobic recovery. Thus, it was suggested that the reduced mobility of the polymer chain because of the presence of ionic aggregates results in restricted reorientation of oxygen‐containing groups. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1791–1797, 2003     

Long-lasting hydrophilicity on nanostructured Si-incorporated diamond-like carbon films

We investigated the long-lasting hydrophilic behavior of a Si-incorporated diamond-like carbon (Si-DLC) film by varying the Si fraction in DLC matrix through oxygen and nitrogen plasma surface treatments. The wetting behavior of the water droplets on the pure DLC and Si-DLC with the nitrogen or oxygen plasma treatment revealed that the Si element in the oxygen-plasma-treated Si-DLC films played a major role in maintaining a hydrophilic wetting angle of <10° for 20 days in ambient air. The nanostructured patterns with a roughness of ～10 nm evolved because of the selective etching of the carbon matrix by the oxygen plasma in the Si-DLC film, where the chemical component of the Si-Ox bond was enriched on the top of the nanopatterns and remained for over 20 days.     

Improvement of interfacial adhesion for plasma‐treated aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) composite and fiber surface aging effects

Interfacial adhesion between the fiber and the matrix in a composite is a primary factor for stress transfer from the matrix to the fiber. In this study, oxygen plasma treatment method was applied to modify the fiber surface for improving interfacial adhesion of aramid fiber‐reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite. Composite interfacial adhesion properties were determined by interlaminar shear strength (ILSS) using a short‐beam bending test. The composite interfacial adhesion mechanism was discussed by SEM. The changes of chemical composition and wettability for plasma‐treated fiber surfaces stored in air as long as 10 days were investigated by XPS and dynamic contact angle analysis (DCAA), respectively. Results indicated that oxygen plasma treatment was an effective method for improving interfacial adhesion; plasma‐treated fiber surface suffered aging effects during storage in air. Copyright © 2008 John Wiley & Sons, Ltd.     

Isoelectric points of plasma‐modified and aged silicon oxynitride surfaces measured using contact angle titrations

Acid‐base properties of metal oxides and polymers can control adhesion properties between materials, electrical properties, the physical structure of the material and gas adsorption behavior. To determine the relationships between surface isoelectric point, chemical composition and aging effects, plasma‐surface treatment of amorphous silicon oxynitride (SiO_xN_y) substrates was explored using Ar, H₂O vapor, and NH₃ inductively coupled rf plasmas. Overall, the Ar plasma treatment resulted in nonpermanent changes to the surface properties, whereas the H₂O and NH₃ plasmas introduced permanent chemical changes to the SiO_xN_y surfaces. In particular, the H₂O plasma treatments resulted in formation of a more ordered SiO₂ surface, whereas the NH₃ plasma created a nitrogen‐rich surface. The trends in isoelectric point and chemical changes upon aging for one month suggest that contact angle and composition are closely related, whereas the relationship between IEP and composition is not as directly correlated. Copyright © 2010 John Wiley & Sons, Ltd.     

Creation of low hysteresis superhydrophobic paper by deposition of hydrophilic diamond-like carbon films

The creation of low hysteresis superhydrophobic paper is reported using a combination of oxygen plasma etching and plasma deposition of an 80 nm non-fluorinated, hydrophilic diamond-like carbon (DLC) coating. The DLC has an equilibrium (flat surface) contact angle (θ _e ) of 68.2° ± 1.5°, which is well below the 90° contact angle that is typically believed to be a prerequisite for superhydrophobicity. Coating of paper substrates with the DLC film yields an advancing contact angle of 124.3° ± 4.1°, but the surface remains highly adhesive, with a receding contact angle <10°. After 60 min of plasma etching and DLC coating, a low hysteresis, superhydrophobic surface is formed with an advancing contact angle of 162.0° ± 6.3° and hysteresis of 8.7° ± 1.9°. To understand the increase in contact angle and decrease in hysteresis, atomic force microscopy and optical profilometry studies were performed. The data demonstrates that while little additional nanoscale roughness is imparted beyond the first 5 min of etching, the roughness at the microscale continually increases. The hierarchical structure provides the appropriate roughness to create low hysteresis superhydrophobic paper from a hydrophilic coating.     

Exchange of Methyl‐ and Azobenzene‐Terminated Alkanethiols on Polycrystalline Gold Studied by Tip‐Enhanced Raman Mapping

Mixed thiol self‐assembled monolayers (SAMs) presenting methyl and azobenzene head groups were prepared by chemical substitution from the original single‐component n‐decanethiol or [4‐(phenylazo)phenoxy]hexane‐1‐thiol SAMs on polycrystalline gold substrates. Static contact‐angle measurements were carried out to confirm a change in the hydrophobicity of the functionalized surfaces following the exchange reaction. The mixed SAMs presented contact‐angle values between those of the more hydrophobic n‐decanethiol and the more hydrophilic [4‐(phenylazo)phenoxy]hexane‐1‐thiol single‐component SAMs. By means of tip‐enhanced Raman spectroscopy (TERS) mapping experiments, it was possible to highlight that molecular replacement takes place easily and first at grain boundaries: for two different mixed SAM compositions, TERS point‐by‐point maps with <50 nm step sizes showed different spectral signatures in correspondence to the grain boundaries. An example of the substitution extending beyond grain boundaries and affecting flat areas of the gold surface is also shown.     

Surface characterization of plasma‐modified poly(ethylene terephthalate) film surfaces

Poly(ethylene terephthalate) (PET) film surfaces were modified by argon (Ar), oxygen (O₂), hydrogen (H₂), nitrogen (N₂), and ammonia (NH₃) plasmas, and the plasma‐modified PET surfaces were investigated with scanning probe microscopy, contact‐angle measurements, and X‐ray photoelectron spectroscopy to characterize the surfaces. The exposure of the PET film surfaces to the plasmas led to the etching process on the surfaces and to changes in the topography of the surfaces. The etching rate and surface roughness were closely related to what kind of plasma was used and how high the radio frequency (RF) power was that was input into the plasmas. The etching rate was in the order of O₂ plasma > H₂ plasma > N₂ plasma > Ar plasma > NH₃ plasma, and the surface roughness was in the order of NH₃ plasma > N₂ plasma > H₂ plasma > Ar plasma > O₂ plasma. Heavy etching reactions did not always lead to large increases in the surface roughness. The plasmas also led to changes in the surface properties of the PET surfaces from hydrophobic to hydrophilic; and the contact angle of water on the surfaces decreased. Modification reactions occurring on the PET surfaces depended on what plasma had been used for the modification. The O₂, Ar, H₂, and N₂ plasmas modified mainly CH₂ or phenyl rings rather than ester groups in the PET polymer chains to form C? O groups. On the other hand, the NH₃ plasma modified ester groups to form C? O groups. Aging effects of the plasma‐modified PET film surfaces continued as long as 15 days after the modification was finished. The aging effects were related to the movement of C?O groups in ester residues toward the topmost layer and to the movement of C? O groups away from the topmost layer. Such movement of the C?O groups could occur within at least 3 nm from the surface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3727–3740, 2004     

Surface characterization and properties of plasma‐modified cyclic olefin copolymer/layered silicate nanocomposites

In this study, cyclic olefin copolymer (COC)/layered silicate nanocomposites (CLSNs) were prepared by the intercalation of COC polymer into organically‐modified layered silicate through the solution mixing process. Both X‐ray diffraction data and transmission electron microscopy images of CLSNs indicate most of the swellable silicate layers were disorderedly intercalated into the COC matrix. The effect of layered silicate on the mechanical and barrier properties of the fabricated nanocomposites shows significant improvements in the storage modulus and water permeability when compared with that of neat COC matrix. Surfaces of COC and CLSN films were modified by a mixture of oxygen (O₂) and nitrogen (N₂) plasmas with various treated times, system pressures, and radio frequency (RF) powers. The surfaces of plasma‐modified COC and CLSN were investigated using scanning probe microscopy and contact‐angle measurements. The exposure of the COC and CLSN film to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new functional groups onto polymer surfaces to change the topology of COC film surfaces. The surface roughness was closely related to how high and how long the RF power was input into the system. The plasmas also led to changes in the surface properties of the CLSN surfaces from hydrophobic to hydrophilic; and the contact angle of water on the surface decreases. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2745–2753, 2005