Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO4 and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g(-1), calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times above the detection limit, was typically 5%.     

Comparison of gas chromatographic hyphenated techniques for mercury speciation analysis

In this study, we evaluate advantages and disadvantages of three hyphenated techniques for mercury speciation analysis in different sample matrices using gas chromatography (GC) with mass spectrometry (GC-MS), inductively coupled plasma mass spectrometry (GC-ICP-MS) and pyrolysis atomic fluorescence (GC-pyro-AFS) detection. Aqueous ethylation with NaBEt(4) was required in all cases. All systems were validated with respect to precision, with repeatability and reproducibility <5% RSD, confirmed by the Snedecor F-test. All methods proved to be robust according to a Plackett-Burnham design for 7 factors and 15 experiments, and calculations were carried out using the procedures described by Youden and Steiner. In order to evaluate accuracy, certified reference materials (DORM-2 and DOLT-3) were analyzed after closed-vessel microwave extraction with tetramethylammonium hydroxide (TMAH). No statistically significant differences were found to the certified values (p=0.05). The suitability for water samples analysis with different organic matter and chloride contents was evaluated by recovery experiments in synthetic spiked waters. Absolute detection and quantification limits were in the range of 2-6 pg for GC-pyro-AFS, 1-4 pg for GC-MS, with 0.05-0.21 pg for GC-ICP-MS showing the best limits of detection for the three systems employed. However, all systems are sufficiently sensitive for mercury speciation in environmental samples, with GC-MS and GC-ICP-MS offering isotope analysis capabilities for the use of species-specific isotope dilution analysis, and GC-pyro-AFS being the most cost effective alternative.     

On-line preconcentration of mercury by sorption on an anion-exchange resin loaded with 1,5-bis[(2-pyridyl)-3-sulphophenyl methylene] thiocarbonohydrazide and determination by cold-vapour inductively coupled plasma atomic emission

1,5-Bis[(2-pyridyl)-3-sulphophenyl methylene] thiocarbonohydrazide (PSTH) immobilized on an anion-exchange resin (Dowex) has been used for the on-line preconcentration of mercury from biological samples and waters prior to its determination by inductively coupled plasma atomic emission spectroscopy. The metal was eluted from the column using a solution of 2 M HNO(3) and mixed on-line with SnCl(2). The optimum experimental conditions were evaluated for the continuous preconcentration of Hg, the direct generation of mercury vapour and the final determination of this element by ICP-AES. The enrichment, together with low blank levels of the optimized procedure, allow the simple determination of this toxic element at concentrations down to a few nanograms per milliliter. The proposed method has a linear calibration range 5-1000 ng ml(-1) of mercury, with a detection limit of 4 ng ml(-1) (S/N=3) and a sampling rate of 40 h(-1), investigated with a 9 ml sample volume. The precision of the method (evaluated as the relative standard deviation obtained after analyzing ten series of ten replicates) was +/-3.6% at the 10 ng ml(-1) level of Hg(II) and +/-1.3% at the 100 ng ml(-1) level. The accuracy of the method was examined by the analysis of certified reference materials.     

Speciation of Mercury in Microalgae by Isotope Dilution-inductively Coupled Plasma Mass Spectrometry

Species-specific stable isotope dilution in combination with gold trap- or gas chromatography (GC)-inductively coupled plasma mass spectrometry (ICP-MS) is reported for the determination of inorganic mercury and methylmercury in diatoms (Chaetoceros curvisetus). The optimum conditions for the separation parameters were established. The isotope dilution analysis was performed using ¹⁹⁹Hg-enriched Hg²⁺ and laboratory-synthesized ²⁰¹Hg-enriched methylmercury. The absolute detection limits obtained with isotope dilution-ICP-MS were 9 pg for total mercury and 0.6 pg for methylmercury. The relative error of 7 Hg isotopic abundances based on the peak area measurements was better than 2.0% for 20 pg of methylmercury (as Hg) and 250 pg of inorganic mercury. The accuracy of the method was validated with a biological certified reference material. The developed method was then applied to investigate the uptake of inorganic mercury and methylmercury by C. curvisetus. Continuous uptake of inorganic mercury and methylmercury was observed during 5 days of incubation.     

Simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg in sonicate slurries of biological and environmental reference materials by hydride generation microwave induced plasma optical emission spectrometry (SS-HG-MIP-OES)

A slurry sampling hydride generation (SS-HG) method for the simultaneous determination of hydride forming elements (As, Sb, Se, Sn) and Hg, without total sample digestion, has been developed using batch mode generation system coupled with microwave induced plasma optical emission spectrometry (MIP-OES) from certified biological and environmental reference materials. Slurry concentration up to 3.6% m/v (particles < 80 μm) prepared in 10% HCl containing 100 μl of decanol, by the application of ultrasonic agitation, was used with calibration by the standard addition technique. Harsh conditions were used in the slurry preparation in order to reduce the hydride forming elements to their lower oxidation states, As(III), Sb(III), Se(IV) and Sn(II) and Hg, being reduced to mercury vapor, before reacting with sodium tetrahydroborate. An ultrasonic probe was used to homogenize the slurry in the quartz cup just before its introduction into the reaction vessel. For 10 ml of slurry sample, detection limits (LOD, 3σ_blank, peak area) of 0.06, 0.08, 0.15, 0.12 and 0.10 μg g^− 1 were obtained for As, Sb, Se, Sn and Hg, respectively. The method offers relatively good precision (RSD ranged from 9 to 12%) for slurry analysis. To test the accuracy, three certified reference materials were analyzed with the analyte concentrations mostly in the μg g^− 1 level. Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: NRCC LUTS-1 (lobster hepatopancreas), NRCC DOLT-2 (Dogfish Liver) and environmental reference material: NRCC PACS-1 (Marine Sediment), all adequate for slurry sampling. The method requires small amounts of reagents and reduces contamination and losses.     

Direct determination of trace amounts of sodium in water-soluble organic pharmaceuticals by microwave induced plasma atomic emission spectrometry

The direct determination of trace sodium by microwave induced plasma atomic emission spectrometry (MIP-AES) in water-soluble organic substances utilized in pharmaceutical preparations was developed. No decomposition of the organic constituents was required. Samples were dissolved with water and introduced to the plasma after ultrasonic nebulization without desolvation. A limit of detection (3sigma) of 0.91-3.0 ng ml(-1) was obtained under experimental conditions. The quantitative MIP-AES procedure involved the standard addition method. The sodium content determined in reference material NIST SRM 1568A Rice Flour agreed with the certified value (6.6+/-0.8 mug g(-1)). Physical and chemical interferences were investigated. It was found for the microwave plasma that it is possible to introduce organic substances solutions of concentration up to 5% without sensitivity losses. This direct technique is fast and sensitive and helps to reduce contamination connected with the sample preparation procedure.     

Efficiency of solvent extraction methods for the determination of methyl mercury in forest soils

Methyl mercury was determined by gas chromatography, microwave induced plasma, atomic emission spectrometry (GC-MIP-AES) using two different methods. One was based on extraction of mercury species into toluene, pre-concentration by evaporation and butylation of methyl mercury with a Grignard reagent followed by determination. With the other, methyl mercury was extracted into dichloromethane and back extracted into water followed by in situ ethylation, collection of ethylated mercury species on Tenax and determination. The accuracy of the entire procedure based on butylation was validated for the individual steps involved in the method. Methyl mercury added to various types of soil samples showed an overall average recovery of 87.5%. Reduced recovery was only caused by losses of methyl mercury during extraction into toluene and during pre-concentration by evaporation. The extraction of methyl mercury added to the soil was therefore quantitative. Since it is not possible to directly determine the extraction efficiency of incipient methyl mercury, the extraction efficiency of total mercury with an acidified solution containing CuSO₄ and KBr was compared with high-pressure microwave acid digestion. The solvent extraction efficiency was 93%. For the IAEA 356 sediment certified reference material, mercury was less efficiently extracted and determined methyl mercury concentrations were below the certified value. Incomplete extraction could be explained by the presence of a large part of inorganic sulfides, as determined by ¶x-ray absorption near-edge structure spectroscopy (XANES). Analyses of sediment reference material CRM 580 gave results in agreement with the certified value. The butylation method gave a detection limit for methyl mercury of 0.1 ng g^–1, calculated as three times the standard deviation for repeated analysis of soil samples. Lower values were obtained with the ethylation method. The precision, expressed as RSD for concentrations 20 times above the detection limit, was typically 5%.     

On-line hyphenation of capillary electrophoresis with flame-heated furnace atomic absorption spectrometry for trace mercury speciation

Capillary electrophoresis (CE) was directly interfaced to flame-heated furnace atomic absorption spectrometry (FHF-AAS) via a laboratory-made thermospray interface for nanoliter trace element speciation. The CE-FHF-AAS interface integrated the superiorities of stable CE separation, complete sample introduction, and continuous vaporization for AAS detection without the need of extra external heat sources and any post-column derivation steps. To demonstrate the usefulness of the developed hybrid technique for speciation analysis, three environmentally significant and toxic forms of methylmercury (MeHg), phenylmercury (PhHg), and inorganic mercury (Hg(II)) were taken as model analytes. Baseline separation of the three mercury species was achieved by CE in a 60 cm long x 75 microm inner diameter fused-silica capillary at 20 kV and using a mixture of 100 mM boric acid and 10% v/v methanol (pH 8.30) as running electrolyte. The precision (relative standard deviation, RSD, n = 7) of migration time, peak area and peak height for the mercury species at 500 microg x L(-1) (as Hg) level were in the range of 0.9-1.2%, 1.5-1.9%, and 1.4-2.0%, respectively. The detection limit (S/N = 3) of three mercury species was 3.0 +/- 0.15 pg (as Hg), corresponding to 50.8 +/- 2.4 microg x L(-1) (as Hg) for 60 nL sample injection, which was almost independent on specific mercury species. The developed hybrid technique was successfully applied to the speciation analysis of mercury in a certified reference material (DORM-2, dogfish muscle).     

A new fully automated on-line digestion system for ultra trace analysis of mercury in natural waters by means of FI-CV-AFS

A fully automated flow injection (FI) system utilizing the extraordinary oxidation power of bromine monochloride (BrCl) for the transformation of dissolved mercury species to Hg(2+) and oxidation of dissolved organic carbon (DOC) has been developed and coupled to cold vapor (CV) atomic fluorescence spectrometry (AFS) for highly sensitive mercury detection. The system can be applied to natural waters, sea water as well as freshwater and provides a detection limit as low as 16 pg Hg l(-1) from a sample volume of 7 ml. The relative standard deviation is about 4-10%. A 3-fold measurement of one sample is completely processed within 15 min. Dissolved organic carbon, chloride and iodide ions are tolerated in concentrations of 15 mg DOC l(-1), >21 g Cl(-)l(-1), and 10 mg I(-)l(-1). Validation of the proposed method yielded a good recovery of total mercury in a moorland water sample and in the certified reference material ORMS-3, river water. Investigation of eight real water samples with mercury concentrations in the range of 0.3-1.4 ng l(-1) also confirmed the suitability of the proposed method.     

Speciation analysis for mercury in gas condensates by capillary gas chromatography with inductively coupled plasma mass spectrometric detection

A method allowing species-selective determination of atomic mercury, non-polar dialkylated mercury compounds,polar monoalkylated species and inorganic mercury complexes in natural gas condensates was developed. Inductively coupled plasma mass spectrometry was employed as a detection method for capillary gas chromatography and compared with microwave induced plasma atomic emission detection for the analysis of hydrocarbon-rich matrices. The method was based on two consecutive injections allowing comprehensive speciation analysis. First a sample aliquot was diluted with toluene and analysed for Hg0 and individual dialkylmercury compounds. Then, another aliquot was butylated with a Grignard reagent for the species specific determination of Hg(II) and monoalkylated mercury species. The detection limits were down to 0.08 pg level.     

Determination of precious metals in geological samples by continuous powder introduction microwave induced plasma atomic emission spectrometry after preconcentration on activated carbon

A novel method was developed for analysing geological materials for Au, Ag, Pd and Pt by continuous powder introduction microwave induced plasma atomic emission spectrometry (CPI-MIP-AES). The preconcentration of the trace metals on activated carbon (AC) was performed before conducting MIP-AES measurements in order to obtain accurate and precise analytical results. The method proposed is based on the selective sorption of precious metals that are subsequently introduced to the plasma as a dry particulate aerosol consisted of analytes collected on the sorbent. The technical design and operating conditions of the novel sample introduction system based on the fluidized-bed concept has been optimized. The microwave excitation source with integrated rectangular cavity TE₁₀₁ and vertically positioned plasma torch has been used. The signal stability proved to be adequate for sequential mode of measurements due to the vertical plasma configuration as well as the MIP-AES system compatibility with the CPI technique. Calibration was done using home-made standards obtained by sorption of metals of interest from standard solutions on activated carbon. Precision is typically 1-4% relative standard deviation at the 1 μg g⁻¹ level. Under measurement conditions the detection limits for Ag, Au, Pd and Pt were 24, 43, 57 and 550 ng per 1 g of AC, respectively. The proposed procedure was used for Au, Ag, Pd and Pt determination in the platinum ore SARM-7 as well as Au and Ag in the Chinese soil GBW-07405 certified reference materials. The standard addition technique was used and recoveries revealed that the proposed method shows good accuracy and precision.     

Optimization of microwave digestion for mercury determination in marine biological samples by cold vapour atomic absorption spectrometry

Optimization of acid digestion method for mercury determination in marine biological samples (dolphin liver, fish and mussel tissues) using a closed vessel microwave sample preparation is presented. Five digestion procedures with different acid mixtures were investigated: the best results were obtained when the microwave-assisted digestion was based on sample dissolution with HNO3-H2SO4-K2Cr2O7 mixture. A comparison between microwave digestion and conventional reflux digestion shows there are considerable losses of mercury in the open digestion system. The microwave digestion method has been tested satisfactorily using two certified reference materials. Analytical results show a good agreement with certified values. The microwave digestion proved to be a reliable and rapid method for decomposition of biological samples in mercury determination.     

Mercury speciation in sea food by flow injection cold vapor atomic absorption spectrometry using selective solid phase extraction

An on-line inorganic and organomercury species separation, preconcentration and determination system consisting of cold vapor atomic absorption spectrometry (CV-AAS or CV-ETAAS) coupled to a flow injection (FI) method was studied. The inorganic mercury species was retained on a column (i.d., 3 mm; length 3 cm) packed to a height of 0.7 cm with a chelating resin aminopropyl-controlled pore glass (550 A) functionalized with [1,5-bis (2 pyridyl)-3-sulphophenyl methylene thiocarbonohydrazyde] placed in the injection valve of a simple flow manifold. Methylmercury is not directly determined. Previous oxidation of the organomercurial species permitted the determination of total mercury. The separation of mercury species was obtained by the selective retention of inorganic mercury on the chelating resin. The difference between total and inorganic mercury determined the organomercury content in the sample. The inorganic mercury was removed on-line from the microcolumn with 6% (m/v) thiourea. The mercury cold vapor generation was performed on-line with 0.2% (m/v) sodium tethrahydroborate and 0.05% (m/v) sodium hydroxide as reducing solution. The determination was performed using CV-AAS and CV-ETAAS, both approaches have been used and compared for the speciation of mercury in sea food. A detection limit of 10 and 6 ng l(-1) was achieved for CV-AAS and CV-ETAAS, respectively. The precision for 10 replicate determinations at the 1 microg l(-1) Hg level was 3.5% relative standard deviation (R.S.D.), calculated from the peak heights obtained. Both approaches were validated with the use of two certified reference materials and by spiking experiments. By analyzing the two biological certified materials, it was evident that the difference between the total mercury and inorganic mercury corresponds to methylmercury. The concentrations obtained by both techniques were in agreement with the certified values or with differences of the certified values for total Hg(2+) and CH(3)Hg(+), according to the t-test for a 95% confidence level. It is amazing how this very simple method is able to provide very important information on mercury speciation.     

Method to reduce the memory effect of mercury in the analysis of fish tissue using inductively coupled plasma mass spectrometry

The routine determination of mercury (Hg) by inductively coupled plasma mass spectrometry (ICP-MS) is affected by a pronounced memory effect in the sample introduction system. This results in long washout times for the analyte, which affects the accuracy and reliability of the analytical procedure. By using a combination of flow injection sample introduction and a sulfur-containing compound in the carrier solution, it was possible to decrease the memory effect of mercury to that for the internal standard (rhodium). The carrier solution contained 2-mercaptoethanol (2-ME) and the developed method was evaluated using three different fish tissue certified reference materials: CRM 464 (BCR, Brussels); DORM-1; and DORM-2 (NRC, Canada). The samples were mineralized using a combination of concentrated nitric acid and hydrogen peroxide and heating in a closed microwave oven. The developed flow injection ICP-MS procedure gave values for total mercury in all three CRM materials in agreement with the certified concentration range. Cold vapour atomic fluorescence spectrometry (CV-AFS) confirmed the results from the developed method. The developed flow injection method had a detection limit (defined as three times the standard deviation of the blank concentration) for mercury of 5.1 μg l⁻¹.     

Behaviour of the dithiocarbamate complexes of arsenic, antimony, bismuth, mercury, lead, tin and selenium in methanol with a hydride generator

A study was carried out with a continuous hydride generator coupled to an atomic emission spectrometer with inductively-coupled plasma to determine whether hydrides of As, Bi, Pb, Sb, Sn and Se and mercury vapor could be generated in methanol solutions of their dithiocarbamate complexes. It was found that (with the exception of Pb) hydride generation with sufficient efficiency for simultaneous multi-element determination is achieved using 0.25% NaBH(4)-0.6 mol 1(-1) HCl as reaction medium. The detection limit was found to be 0.2 ng ml(-1) for As, 30 ng ml(-1) for Bi, 0.03 ng ml(-1) for Se, Sb and Sn.     

A novel capillary microextraction on ordered mesoporous titania coating combined with electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of V, Cr and Cu in environmental and biological samples

In this work, an ordered mesoporous titania film was introduced to coat a capillary by means of sol-gel technique. Sol-gel titania coating was developed for the preconcentration/separation of trace V, Cr and Cu by capillary microextraction (CME), and the adsorbed analytes were eluted for electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) detection. By immobilizing sol-gel titania on the inner surface of a fused-silica microextraction capillary, the sol-gel titania coating was prepared easily. Its adsorption properties, stability and the factors affecting the adsorption behaviors of V, Cr and Cu were investigated in detail. At pH range of 7 to 9, the titania-coated capillary (50 cm x 0.25 mm) is selective towards V, Cr and Cu, and the target analytes could be desorbed quantitatively with 50 microl of 1.0 mol l(-1) HNO3 at the rate of 0.05 ml min(-1). With a consumption of 2 ml sample solution, an enrichment factor of 33.3, and a detection limit (3 s) of 1.1 pg ml(-1) (10.5 fg) for V; 3.3 pg ml(-1) (33.0 fg) for Cr and 6.3 pg ml(-1) (63.1 fg) for Cu respectively were obtained. The precisions Relative Standard Deviations (RSDs) for nine replicate measurements of 1 ng ml(-1) V, Cr and Cu were 3.4, 5.1 and 6.4%, respectively. The proposed method has been applied to the determination of V, Cr and Cu in human urine and lake water, and the recoveries for these elements were 89.2 approximately 105%. The developed method was also applied to the determination of the target elements in NIES No. 10-a (rice flour-unpolished) and NIES No. 9 (sargasso) certified reference materials, and the results found are in good agreement with the certified values.     

Sensitive determination of bromine and iodine in aqueous and biological samples by electrothermal vaporization inductively coupled plasma mass spectrometry using tetramethylammonium hydroxide as a chemical modifier

A procedure for the simultaneous determination of bromine and iodine by inductively coupled plasma (ICP) mass spectrometry was investigated. In order to prevent the decrease in the ionization efficiencies of bromine and iodine atoms caused by the introduction of water mist, electrothermal vaporization was used for sample introduction into the ICP mass spectrometer. To prevent loss of analytes during the drying process, a small amount of tetramethylammonium hydroxide solution was placed as a chemical modifier into the tungsten boat furnace. After evaporation of the solvent, the analytes instantly vaporized and were then introduced into the ICP ion source to detect the (79)Br(+), (81)Br(+), and (127)I(+) ions. By using this system, detection limits of 0.77 pg and 0.086 pg were achieved for bromine and iodine, respectively. These values correspond to 8.1 pg mL(-1) and 0.91 pg mL(-1) of the aqueous bromide and iodide ion concentrations, respectively, for a sampling volume of 95 microL. The relative standard deviations for eight replicate measurements were 2.2% and 2.8% for 20 pg of bromine and 2 pg of iodine, respectively. Approximately 25 batches were vaporizable per hour. The method was successfully applied to the analysis of various certified reference materials and practical situations as biological and aqueous samples. There is further potential for the simultaneous determination of fluorine and chlorine.     

Mercury speciation by HPLC-cold-vapour radiofrequency glow-discharge optical-emission spectrometry with on-line microwave oxidation

Hollow-cathode (HC) radiofrequency glow-discharge (rf-GD) optical-emission spectrometry (OES) has been used as detector for the determination of inorganic mercury by cold-vapour (CV) generation in a flow-injection (FI) system. Both NaBH4 and SnCl2 were evaluated as reducing reagents for production of mercury CV. The conditions governing the discharge (pressure, He flow rate, and delivered power) and Hg CV generation (NaBH4 or SnCl2 concentration and reagent flow rate) were optimized using both reducing agents. The analytical performance characteristics of FI-CV-rf-GD-OES for mercury detection were evaluated at the 253.6 nm emission mercury line. Detection limits (DL) of 0.2 ng mL(-1) using SnCl2 and 1.8 ng mL(-1) using NaBH4 were obtained (100 microliter sample injections were used). When the optimized experimental conditions using SnCl2 had been determined, the analytical potential of this CV-rf-GD-OES method was investigated as on-line detector for high-performance liquid chromatographic (HPLC) speciation of mercury (Hg(II) and methylmercury). The HPLC-CV-rf-GD-OES detection limits for 100 microliter sample injections were found to be 1.2 and 1.8 ng mL(-1) (as mercury) of inorganic mercury and methylmercury, respectively. The reproducibility observed was below +/- 8% for both species. Finally, the HPLC-CV-rf-GD-OES system developed was successfully applied to the determination of methylmercury (speciation) in two certified reference materials, Dorm-2 and Dolt-2.     

Partial microwave-assisted wet digestion of animal tissue using a baby-bottle sterilizer for analyte determination by inductively coupled plasma optical emission spectrometry

A procedure for partial digestion of bovine tissue is proposed using polytetrafluoroethylene (PTFE) micro-vessels inside a baby-bottle sterilizer under microwave radiation for multi-element determination by inductively coupled plasma optical emission spectrometry (ICP OES). Samples were directly weighed in laboratory-made polytetrafluoroethylene vessels. Nitric acid and hydrogen peroxide were added to the uncovered vessels, which were positioned inside the baby-bottle sterilizer, containing 500 mL of water. The hydrogen peroxide volume was fixed at 100 µL. The system was placed in a domestic microwave oven and partial digestion was carried out for the determination of Ca, Cu, Fe, Mg, Mn and Zn by inductively coupled plasma optical emission spectrometry. The single-vessel approach was used in the entire procedure, to minimize contamination in trace analysis. Better recoveries and lower residual carbon content (RCC) levels were obtained under the conditions established through a 2^4-1 fractional factorial design: 650 W microwave power, 7 min digestion time, 50 µL nitric acid and 50 mg sample mass. The digestion efficiency was ascertained according to the residual carbon content determined by inductively coupled plasma optical emission spectrometry. The accuracy of the proposed procedure was checked against two certified reference materials.     

Determination of total mercury in environmental and biological samples by flow injection cold vapour atomic absorption spectrometry

A simple and accurate method has been developed for the determination of total mercury in environmental and biological samples. The method utilises an off-line microwave digestion stage followed by analysis using a flow injection system with detection by cold vapour atomic absorption spectrometry.

The method has been validated using two certified reference materials (DORM-1 dogfish and MESS-2 estuarine sediment) and the results agreed well with the certified values. A detection limit of 0.2 ng g⁻¹ Hg was obtained and no significant interference was observed. The method was finally applied to the determination of mercury in river sediments and canned tuna fish, and gave results in the range 0.1–3.0 mg kg⁻¹.