Trace determination of molybdenum by adsorptive cathodic stripping voltammetry

Molybdenum is determined by adsorptive cathodic stripping voltammetry in 0.15 M nitric acid solution containing 15 μM 2′,3,4′,5,7-pentahydroxyflavone (morin) as a ligand. In this medium, molybdenum is preconcentrated on a hanging mercury drop electrode and stripped cathodically in square-wave voltammetry mode, with a peak potential of -350 mV vs. Ag/AgCl (saturated KCl). The effect of various parameters (ligand concentration, supporting electrolyte composition, accumulation potential and collection time) on the sensitivity and linear range of the calibration curve are discussed. With controlled accumulation for 1 min, the detection limit (3σ) was 0.45 ng ml^?1 molybdenum and the calibration curve is linear up to 70 ng ml^?1. The procedure is applied to the determination of molybdenum in real samples with satisfactory results.     

Determinationation of kanamycin by square-wave cathodic adsorptive stripping voltammetry

A square-wave cathodic adsorptive stripping voltametric (SWCASV) method for the determination of kanamycin was developed on a thin-film mercury electrode (TFME). The optimal working conditions for the application of the method were found to be pH 8.0, provided by a Britton-Robinson (B.R.) buffer, and an adsorption potential of +0.30 V during 300 s. The equilibration time was applied during 10 s, and potential scans were performed at a scan rate of 40 mV/s, with a square-wave frequency of 100 Hz. The measuring-system response was linear over the kanamycin concentration range from 1.2 × 10⁻⁹ to 5.0 × 10⁻⁸ M and the detection limit achieved was 4.8 × 10⁻¹⁰ M. The relative error and relative standard deviation obtained were 1.20 and 4.67%, respectively. The voltammetric procedure was applied successfully to give a rapid and precise assay of kanamycin in kanamycin sulfate injection form. Published in Elektrokhimiya in Russian, 2008, Vol. 44, No. 12, pp. 1433–1437. The text was submitted by author in English     

The determination of aluminium in seawater and freshwater by cathodic stripping voltammetry

Dissolved aluminium in seawater and freshwater is determined by cathodic stripping voltammetry (c.s.v.) preceded by adsorptive collection of complex ions with 1,2-dihydroxyanthraquinone-3-sulphonic acid (DASA) on the hanging mercury drop electrode. Complexation of aluminium by DASA is rapid and no waiting period or heating of the sample is required. Optimal conditions are a DASA concentration of 10^?5 M, a solution pH of 7.1–7.3 and an adsorption potential of ?0.9 V; the c.s.v. scan is done in the differential-pulse mode. The limit of detection is 1 nM aluminium for an adsorption time of 45 s. The total time needed, including 50min deaeration and a standard addition, is 10–15 min per sample. No serious interferences were found; u.v. irradiation is recommended for samples containing high levels of organic materials.     

Determination of 2-amino-5-nitrothiazole by square-wave cathodic stripping voltammetry

An electrochemical method has been developed for the detection and determination of 2-amino-5-nitrothiazole (2,5-ANT) by adsorption square-wave voltammetric stripping. The best sensitivity/resolution ratio was obtained by adsorption at pH 8.0 using a phosphate buffer, an accumulation potential of –10 mV (vs. Ag/AgCl 3 mol/l) and an accumulation time of 15 s. Under these conditions, the proposed method provides a linear electrode response over the 2,5-ANT concentration range 5–300 ng ml^–1, and a detection and determination limit of 4 and 7.5 ng ml^–1, respectively. The method was applied to the determination of 2,5-ANT in bacon.     

Determination of selenium in soils with square-wave cathodic stripping voltammetry

A new voltammetric method is elaborated for the trace determination of selenium in soils. The use of the square-wave cathodic stripping voltammetry in the determination step efficiently eliminates the interference of electroactive components. The detection limit is 0.75 g/l.     

Direct determination of sub-nanomolar levels of zinc in sea-water by cathodic stripping voltammetry

A novel technique for the determination of nanomolar levels of zinc in aqueous solution is presented. The zinc complex with ammonium pyrrolidine dithiocarbamate is adsorbed on a hanging mercury-drop electrode and the reduction current of zinc is measured by voltammetry. The detection limit for zinc is 3 × 10⁻¹¹M, with 10-min collection time. A procedure is suggested for the simultaneous determination of Ni and Zn in a single sample.     

Assay of dipyridamole in human serum using cathodic adsorptive square-wave stripping voltammetry

A rapid and sensitive square-wave voltammetric procedure was optimized for the determination of dipyridamole after its adsorption preconcentration onto a hanging mercury drop electrode. The peak current of the first of the two peaks developed for this drug in Britton-Robinson buffer at pH 8.0 has been considered for the present analytical study. An accumulation potential of -1.0 V versus Ag/AgCl/KCl(s), pulse amplitude a =100 mV, scan increment Delta E =10 mV, and frequency f =120 Hz were the optimal experimental parameters. Dipyridamole can be determined in the concentration range of 9.0 x 10(-9) to 5.0 x 10(-6) M using accumulation times of 30-300 s. A detection limit of 4.0 x 10(-11) M was achieved after a 300 s accumulation time. Applicability to serum samples was illustrated. The average recoveries for dipyridamole spiked to serum at 0.25-4.50 micro g ml(-1) were 96.0-102.0%, and the higher standard deviation was 2.9%. A detection limit of 0.06 micro g mL(-1) of serum was obtained.     

Electrochemical determination of rosiglitazone by square-wave adsorptive stripping voltammetry method

Square-wave adsorptive stripping voltammetry technique was used to determine rosiglitazone (ROS) on the hanging mercury dropping electrode (HMDE) surface, in Britton Robinson buffer, pH = 5. The voltammetric cathodic peak was observed at ?1520 mV vs. Ag/AgCl reference electrode. The voltammetric peak response was characterized with respect to pH, supporting electrolyte, accumulation potential, preconcentration time, scan rate, frequency, pulse amplitude, surface area of the working electrode and the convection rate. Under optimal conditions, the voltammetric current is proportional to the concentration of ROS over the concentration range of 5 × 10^?8–8 × 10^?7 mol l^?1 (r = 0.9899) with a detection limit of 3.2 × 10^?11 mol l^?1 using 120 s accumulation time. The developed SW-AdSV procedure showed a good reproducibility, the relative standard deviation RSD% (n = 10) at a concentration level of 5 × 10^?7 mol l^?1 was 0.33%, whereas the accuracy was 101% ± 1.0. The proposed method was successfully applied to assay the drug in the human urine and plasma samples with mean recoveries of 90 ± 0.71% and 86 ± 1.0%, respectively.     

The determination of some 2-thiobarbiturates by cathodic stripping voltammetry

Pulse polarography and cyclic voltammetry are employed in studies of the electrochemical behaviour of 5-ethyl-5'-(l-methylbutyl)-2-thiobarbituric acid (I), l-methyl-5-ethyl-5'-(l-methylpropyl)-2-thiobarbituric acid (II) and l,3-dimethyl-5-ethyl-5'-p-chlorophenyl)-2-thiobarbituric acid (III) in the pH range 4–12. All three compounds show anodic and cathodic waves or peaks in this pH range. Compounds (I) and (II) are oxidized at mercury indicator electrodes to produce mercury salts which can adsorb thereon and are thus amenable to cathodic stripping voltammetric analysis (c.s.v.) down to concentrations of the order of 10^-6 M, which is superior to the sensitivities obtained by differential pulse polarography (d.p.p.) based on a reduction peak. Compound (III) oxidizes to produce sulphur which is subsequently plated as HgS. Again the sensitivity of the c.s.v. method is of the order of lO^-6 M and analytically superior to d.p.p. The optimum pH for the three determinations is 8. The determination of (II) in the presence of its oxygenated analogue and metabolite, phemitone, and the effect of chloride ions are reported.     

Determination of total inorganic iodine in seawater by cathodic stripping square wave voltammetry

A method has been designed for the reduction of iodate to iodide in seawater and subsequent determination of total dissolved iodine as iodide by cathodic stripping square wave voltammetry. The pH of the sample is lowered to about 1-2 and iodate is reduced to iodide with sodium sulfite under this acidic condition. The pH of the sample is then raised to 8-9 before the concentration of iodide is measured.     

Flow-through coulometric stripping analysis and the determination of manganese by cathodic stripping voltammetry

A simple flow-through system is described for collection of liquid samples into a closed loop. This arrangement can be used for coulometric determinations by the stripping method without previous calibration. The usefulness of the system is demonstrated on the determination of manganese (ca. 10^-6 M) in acetate buffer by cathodic stripping voltammetry.     

The determination of molybdenum in selected mushrooms by stripping voltammetry

The highly sensitive method of adsorptive stripping voltammetry (AdSV), with differential pulse steps, was performed at a mercury film electrode and has been applied here for the determination of trace molybdenum content in selected wild mushrooms. Fruiting body caps of 12 selected macrofungi species from Basidiomycetes have been investigated. Molybdenum content of investigated samples was determined in the range of 0.006 to 0.38 mg kg⁻¹ of dry matter. The highest value of molybdenum content was found in Leccinum rufum and the lowest in Lactarius deliciosus.     

The determination of platinum in sea water by adsorptive cathodic stripping voltammetry

The catalytic effect of the formazone complex with platinum on the development of hydrogen at a mercury electrode is used to provide a very sensitive method of determining dissolved platinum in fresh and sea water by adsorptive cathodic stripping voltammetry. The optimal analytical conditions include the addition of 0.012% (w/v) formaldehyde, 0.0015% (w/v) hydrazine and 0.5 M sulphuric acid to the sea water. The complex is adsorbed for 1–20 min at ?0.925 V on the hanging mercury drop electrode, followed by a differential-pulse scan in a negative direction. The hydrogen reduction peak catalysed by the platinum complex appears at ?1.045 V. The limit of detection is 0.04 pM Pt with an adsorption time of 10 min, which is quite sufficient to determine dissolved platinum in sea water. The interference of surface-active compounds is eliminated by ultraviolet irradiation of the acidified sample. The method is applied to several sea-water samples. Comparative experiments showed that stripping chronopotentiometry is not sufficiently sensitive to determine platinum in sea water without preconcentration.     

Theoretical and experimental study of the catalytic cathodic stripping square-wave voltammetry of chromium species

The electrocatalytic mechanism of Cr(III) reduction in the presence of diethylenetriaminepentaacetic acid (DTPA) and nitrate ions is studied theoretically and experimentally by using stripping square-wave voltammetry (SWV). Experimental curves are in excellent agreement with theoretical profiles corresponding to a catalytic reaction of second kind. This type of mechanism is equivalent to a CE mechanism, where the chemical reaction produces the electroactive species. Accordingly, the reaction of Cr(III)–H₂O–DTPA and \( {\mathrm{NO}}_3^{-} \) would produce the electroactive species Cr(III)–NO₃–DTPA and this last species would release \( {\mathrm{NO}}_2^{-} \) to the solution during the electrochemical step. In this regard, the complex of Cr(III)–DTPA would work as the catalyzer that allows the reduction of \( {\mathrm{NO}}_3^{-} \) to \( {\mathrm{NO}}_2^{-} \). Furthermore, it was found that the electrochemical reaction is quite irreversible, with a constant of k _s?=?9.4?×?10^?5 cm s^?1, while the constant for the chemical step has been estimated to be k _chem?=?1.3?×?10⁴ s^?1. Considering that the equilibrium constant is K?=?0.01, it is possible to estimate the kinetic constants of the chemical reaction as k ₁?=?1?×?10² s^?1 and k _?1?=?1.29?×?10⁴ s^?1. These values of k ₁ and k _?1 indicate that the exchange of water molecules by nitrate is fast and that the equilibrium favors the complex with water. Also, a value for the formal potential E°’?≈??1.1 V was obtained. The model used for simulating experimental curves does not consider the adsorption of reactants yet. Accordingly, weak adsorption of reagents should be expected.     

Iron organic speciation determination in rainwater using cathodic stripping voltammetry

A sensitive method using Competitive Ligand Exchange-Adsorptive Cathodic Stripping Voltammetry (CLE-ACSV) has been developed to determine for the first time iron (Fe) organic speciation in rainwater over the typical natural range of pH. We have adapted techniques previously developed in other natural waters to rainwater samples, using the competing ligand 1-nitroso-2-naphthol (NN). The blank was equal to 0.17 ± 0.05 nM (n = 14) and the detection limit (DL) for labile Fe was 0.15 nM which is 10–70 times lower than that of previously published methods. The conditional stability constant for NN under rainwater conditions was calibrated over the pH range 5.52–6.20 through competition with ethylenediaminetetraacetic acid (EDTA). The calculated value of the logarithm of β^′_Fe3+(NN)3${{\beta }^{\prime }}_{{\text{Fe}}^{3+}{(\text{NN})}_3}$ increased linearly with increasing pH according to log β^′_Fe3+(NN)3=2.4±0.6×pH+11.9±3.5$\text{log}{{\beta }^{\prime }}_{{\text{Fe}}^{3+}{(\text{NN})}_3}=2.4\pm 0.6\times \text{pH}+11.9\pm 3.5$ (salinity = 2.9, T = 20 °C). The validation of the method was carried out using desferrioxamine mesylate B (DFOB) as a natural model ligand for Fe. Adequate detection windows were defined to detect this class of ligands in rainwater with 40 μM of NN from pH 5.52 to 6.20. The concentration of Fe-complexing natural ligands was determined for the first time in three unfiltered and one filtered rainwater samples. Organic Fe-complexing ligand concentrations varied from 104.2 ± 4.1 nM equivalent of Fe(III) to 336.2 ± 19.0 nM equivalent of Fe(III) and the logarithm of the conditional stability constants, with respect to Fe³⁺, varied from 21.1 ± 0.2 to 22.8 ± 0.3. This method will provide important data for improving our understanding of the role of wet deposition in the biogeochemical cycling of iron.     

Direct determination of bismuth(III) in sea water by square-wave anodic stripping voltammetry at a glassy-carbon rotating-disk electrode

A method for the determination of bismuth(III) in untreated sea water at its natural pH of 8.1 is described. A bare glassy-carbon rotating-disk electrode is preconditioned by placing in the sample at an applied potential of ?0.8 V vs. Ag/AgCl for 20 min; after stripping to ?0.4 V, bismuth is accumulated for 5 min at ?0.8 V and finally stripped in the square-wave mode. The bismuth peak appears at ca. + 0.10 V vs. Ag/AgCl; peak height is linearly related to concentration up to 2×10^?10 mol dm^?3. The method is highly selective for bismuth. The concentration of Bi(III) in the investigated sample was (6±1)×10^?11 mol dm^?3, or 12±2 ng dm^?3. The different types of response obtained are discussed.     

Determination of chitosan by cathodic stripping voltammetry.

A sensitive method for the determination of chitosan (CTS) by cathodic stripping voltammetry is presented. The method exploits a pair of oxidation-reduction peaks of CTS at -0.62 V (vs. SCE) and -0.54 V (vs. SCE), and an enhancement of the peak current of CTS observed in a 0.05 mol l(-1) potassium hydrogenphthalate buffer solution (pH 2.5). The peak current is linear with the concentration of CTS from 5.0 x 10(-7) to 1.5 x 10(-5) g ml(-1), and the detection limit is 1.0 x 10(-7) g ml(-1). We studied the characteristics and the mechanism of the electrode reaction, which proved that this process was diffusion controlled. This method was applied to determine the content of CTS in real samples with satisfactory results.     

The determination of cysteine at Bi-powder carbon paste electrodes by cathodic stripping voltammetry

The determination of cysteine by means of square wave cathodic stripping voltammetry (SWCSV) is reported here for the first time at Bi-modified carbon paste electrodes (CPEs). The modified electrodes are 17% w/w metallic Bi powder mixed with CP (Bi-CPEs) and the technique is based on the enhancement of Bi surface oxidation in the presence of cysteine at a carefully chosen accumulation potential and the subsequent reduction-stripping of the product (proposed to be bismuth(III) cysteinate) by potential scanning to more negative values. The wide concentration range of 1 × 10⁻⁶–5 × 10⁻⁵ M for cysteine can be assessed by SWCSV using Bi-CPEs and, by appropriate choice of accumulation times, two linear response concentration regimes could be identified: 1 × 10⁻⁶–1 × 10⁻⁵ M (accumulation for 600 s) and 1 × 10⁻⁵–5 × 10⁻⁵ M (accumulation for 100 s), with estimated detection limits of 3 × 10⁻⁷ and 2 × 10⁻⁶ M, respectively.     

Assay of anti-coagulant drug warfarin sodium in pharmaceutical formulation and human biological fluids by square-wave adsorptive cathodic stripping voltammetry

The cyclic voltammogram of the anti-coagulant drug warfarin sodium at the hanging mercury drop electrode exhibited a well-defined single two-electron irreversible peak over the pH range 4-7, which may be attributed to the reduction of the CO double bond of the drug molecule. Based on the interfacial adsorptive character of the drug onto the mercury electrode surface, a square-wave cathodic stripping procedure was optimized for its trace determination. The calibration plot was linear over the concentration range of 5×10⁻⁹ to 4×10⁻⁷ M warfarin sodium in Britton-Robinson (B-R) buffer of pH 5, with limits of detection and quantitation of 6.5×10⁻¹⁰ and 2.1×10⁻⁹ M warfarin sodium, respectively. The proposed procedure was successfully applied for assay of warfarin sodium in its pharmaceutical formulation “hemofarin tablets”, human serum and urine without the necessity for sample pretreatment or time-consuming extraction or evaporation steps, prior to assay of the drug. Limits of detection of 1.1×10⁻⁹ and 1.3×10⁻⁸ M warfarin sodium were achieved, while limits of quanitation of 3.7×10⁻⁹ and 4.3×10⁻⁸ M warfarin sodium were estimated in human serum and urine, respectively. The pharmacokinetic profiles of the drug were studied and the estimated pharmacokinetic parameters were favorably compared with those reported in literature.