Preparation of single-walled carbon nanotube fiber coating for solid-phase microextraction of organochlorine pesticides in lake water and wastewater

The feasibility of single-walled carbon nanotubes (SWCNTs) as adsorbents for solid-phase microextraction was investigated by using organochlorine pesticides (OCPs) as model compounds. SWCNTs were attached onto a stainless steel wire through organic binder. Potential factors affecting the extraction efficiency were optimized, including extraction time, extraction temperature, desorption time, desorption temperature, and salinity. The developed method has a linear range of 2-800 ng/L for most analytes, with coefficients of correlation ranging from 0.9911 to 0.9996, LODs ranged from 0.19 to 3.77 ng/L (S/N = 3), and RSDs in the range of 3.5-13.9% (n = 5). Compared with the commercial PDMS fiber, the SWCNT fiber has better thermal stability (over 350 degrees C) and longer life span (over 150 times). The developed method was applied to determine trace OCPs in lake water and wastewater samples with external standard calibration. Results showed that OCP contamination was very low in these samples, and HCHs were detected in almost all water samples while DDT concentrations were almost under detection limits in these samples. Recoveries obtained at 20 ng/L spiking level were in the range of 88.4-111% for OCPs in lake water. For wastewater samples, however, the recoveries were satisfactory for HCHs (63.6-97.1%) but relatively low for DDTs (44.7-116%) due to the high content of organic matter in wastewater.     

Determination of quinolones in water samples by solid-phase extraction and liquid chromatography with fluorimetric detection

A method is reported for the determination, in water samples, of 10 quinolones which are used as veterinary drugs. Analytes are isolated from samples by solid-phase extraction (SPE) and analysed by reversed-phase high-performance liquid chromatography using fluorimetric detection. A solid-phase extraction procedure based on retention on HBL OASIS cartridges and elution with a mixture of acetonitrile-water in basic medium is suitable for pre-concentration of the analytes. Pre-concentration factors up to 250 can be obtained. The quinolones are separated with an octyl silica-based column and mobile phases consisting of aqueous oxalic acid solutions and acetonitrile mixtures. The attained detection limits of the whole process are in the ng l(-1) level when 250 ml of water sample is processed. Recovery rates, from natural water samples spiked at 2060 ng l(-1) level, range from 70 to 100% and common standard deviation are about 6-12%.     

Factors affecting multiresidue determination of priority herbicides when using solid-phase microextraction

A solid-phase microextraction (SPME) procedure was developed for the determination of 10 selected organonitrogen herbicides (s-ethyl dibropylthiocarbamate [EPTC], molinate, propachlor, trifluralin, simazine, atrazine, propazine, terbuthylazine, alachlor, and prometryn) and was tested with various natural waters. Gas chromatography coupled with flame thermionic and mass spectrometric detection was used for quantitation. For this purpose, polydimethylsiloxane and polyacrylate fibers were used and the factors affecting the SPME process such as pH, ionic strength, methanol content, memory effect, stirring rate, and adsorption-time profile were investigated and optimized. By using spiked liquid chromatography water, optimal factors were determined to be 25% salt, <0.5% methanol, stirring rate of 960 rpm, pH 4, and an equilibrium time of 30 min. These conditions were used in further studies of the fibers and in analysis of natural water samples. The method was applied to spiked natural waters such as ground water, sea water, lake water, and river water at a concentration range of 0.5-10 microg/L. Limits of detection ranged from 5 to 90 ng/L, and precision ranged from 5 to 15% (as relative standard deviation), depending on the pesticide, fiber, and detector used. The recoveries of herbicides were 70.2-118.4%, and the average r2 values of the calibration curves were >0.99 for all analytes. The results demonstrate the suitability of the SPME method to determine these organonitrogen herbicides in various natural waters. River water samples originating from the Epirus region (Northwestern Greece) were analyzed to verify the performance of the optimized method by comparing the results obtained by SPME with those obtained by using conventional solid-phase extraction of the selected herbicides.     

Determination of submicrogram amounts of gallium by ion-exchanger fluorimetry Determination of gallium in natural waters

A method for microdetermination of gallium at ng/ml level has been developed, based on ion-exchanger fluorimetry. The gallium reacts with salicylidene-o-aminophenol to give a highly fluorescent complex, which is fixed on a dextran-type cationic resin. The fluorescence of the resin, packed in a 1-mm silica cell, is measured directly with a solid-surface attachment. The range of concentration of the method is 2.0-10.0 ng/ml, the RSD 1.3% and the detection limit 0.3 ng/ml. The method has been applied to the determination of gallium in natural waters. The gallium content found in tap water was higher than that in raw water. This is related to the use of commercial aluminium salts in the water-treatment plant.     

Advantages of hydride generation interface for selenium speciation in waters by high performance liquid chromatography-inductively coupled plasma mass spectrometry coupling

This paper focuses on the analytical performance improvement of the coupled technique HPLC-ICPMS using on-line collision/reaction cell technology for selenium elemental and speciation analyses at the ng (Se) l(-1) level in aquatic environment. Collision/reaction cell operating parameters were optimised, resulting in selected conditions of 5.5 ml min(-1) H(2) and 0.5 ml min(-1) He mixture. The detection limits obtained were around 5 ng (Se) l(-1) for total analysis, and between 7 and 15 ng (Se) l(-1) depending on the species for speciation analysis. The capability of UV irradiation-hydride generation interfacing to increase detector sensitivity was also evaluated for speciation analysis. The detection limits obtained were in the range 2-8 ng (Se) l(-1) depending on the species. Moreover, such interface allowed to prevent bromine introduction to the ICPMS which is particularly convenient for selenium trace analysis in natural waters as (80)Se is preserved free from BrH interferences. The developed method was validated using certified water with low selenium content (TM Rain 95, NWRI, Canada) and applied to the analysis of different waters.     

Sorption–Atomic Absorption Determination of Trace Elements in Natural Waters Using Simultaneous Atomization of a Solid Concentrate and Suspended Matter

A sorption–atomic absorption technique with dynamic preconcentration on DETATA adsorbents in a microcolumn crucible followed by the direct atomization of a solid matrix (concentrate + suspended matter) was used to determine the total dissolved and suspended Cd, Pb, and Tl (El_dis+ El_susp) in natural waters. The detection limits were 1–3 ng/L for Cd and 5–30 ng/L for Pb and Tl. The results of the sorption–filtration atomic absorption determination of the total dissolved and suspended elements can provide extra information for the speciation analysis of waters.     

Simultaneous determination of carbaryl and azinphos-methyl in water by first-derivative synchronous spectrofluorimetry

A method is proposed for the simultaneous determination of the pesticides carbaryl (CBL) and azinphos-methyl (AZM) in water by first-derivative synchronous spectrofluorimetry. It is based on the alkaline hydrolysis of both pesticides to their metabolites 1-naphthol (from CBL) and anthranilic acid (from AZM). The constant wavelength difference chosen to optimize the determination is Δλ=λ_em?λ_ex=103 nm. CBL is measured at 302/405 nm and AZM at 333/436 nm. The calibration graphs are linear between 2.0 and 500.0 ng/ml for CBL and between 1.2 and 500.0 ng/ml for AZM with detection limits of 0.62 ng/ml and 0.35 ng/ml, respectively. The precision of the method (RSD) is 2.4% at the 80.0 ng/ml level for CBL and 2.5% at the 80.0 ng/ml level for AZM. The method is applied to the determination of both analytes in samples of natural waters.     

Continuous flow system for the determination of trace vanadium in natural waters utilizing in-line preconcentration/separation coupled with catalytic photometric detection

A sensitive and rapid method is presented for the determination of vanadium at ng to sub-ng ml(-1) levels in natural waters, in which in-line preconcentration/separation is directly coupled with catalytic detection of vanadium in a flow-injection system. Vanadium was adsorbed on a small column packed with Sephadex G-25 gel and desorbed with a small volume of 0.010 M HCl. The catalytic action of vanadium on the oxidation of chromotropic acid (1,8-dihydroxy-3,6-naphthalenedisulphonic acid) by bromate in pH 3.8 buffered media was used in the sensitive determination of vanadium. Effective preconcentration/separation of trace vanadium can be achieved from Fe(III), Cu(II) and a large excess of sodium chloride in seawater sample. A linear calibration using a 5 m sample loop was obtained for vanadium in the range 0-2.5 ng ml(-1). The limit of detection was 0.02 ng ml(-1) and the relative standard deviation was 1.2% for 1.0 ng ml(-1) vanadium (n=5). The present FIA system is rapid and sensitive and can be readily applied to river water and coastal seawater samples.     

Separation and Removal of Mercury(II) from Water Samples Using (Acetylacetone)‐2‐Thiol‐Phenyleneimine Immobilized on Anion‐Exchange Resin Prior to Determination by Cold Vapor Inductively Coupled Plasma Atomic Emission Spectroscopy

Abstract

(Acetylacetone)‐2‐thiol‐phenyleneimine (H₂L) immobilized on an anion‐exchange resin (Dowex) was used for separation and removal of mercury from natural water samples and for preconcentration prior to its determination by cold vapor inductively coupled plasma atomic emission spectroscopy. The metal was eluted from the column using a solution of 10% thiourea in 0.1 M HCl. The modified resin is higly selective with an exchange capacity of 1.60 mmol g^?1. Various parameters like pH, column flow rate, and desorbing agents are optimized. The proposed method has a linear calibration range of 15–1000 ng/ml Hg(II), with a relative standard deviation at the 15 ng/ml level of 3.5%. The precision of the method (evaluated as the relative standard deviation obtained after analyzing six series of five replicates) was ±4.2% at the 50 ng/ml level of Hg(II). The method has been used for routine determination of trace levels of mercury species in natural waters. The potential application of modified resin for the removal of mercury(II) from two natural water samples (top water and lake water) spiked with 50 ng/ml of mercury (II) was studied by ICP‐AES, and the results proved that excellent percent extraction of mercury(II) from both natural water samples was obtained by column method using modified resin.     

Methods for selective determination of persistent organochlorine pesticide residues in water and sediments by capillary gas chromatography and electron-capture detection

Different extraction methods were evaluated for the determination of fifteen organochlorine pesticides (OCPs) in water and sediments. Liquid-liquid extraction (LLE) was evaluated for the pesticides analyses in water while Soxhlet extraction (SE) and microwave assisted extraction (MAE) methods were compared in sediment. Of all the extracting solvents used, dichloromethane gave the best results. Percentage recoveries ranged from 71.03 +/- 8.15 (dieldrin) to 101.25 +/- 2.17% [a-benzenehexachloride (alpha-BHC)] in water with LLE. In sediments the percentage recoveries with Soxhlet extraction method varied between 88.22 +/- 7.85 (endrin) and 109.63 +/- 5.10% (beta-BHC) and ranged from 74.11 +/- 9.82 (2,4 DDT) to 97.50 +/- 4.56% (alpha-BHC) with MAE. The limits of detection for the OCPs ranged from 5.5 to 20.6 ng/l and between 0.6 and 2.1 ng/g. respectively. The LLE and the SE methods were applied to water and sediments samples, respectively, from marine and freshwater sources in the Eastern Cape Province of South Africa that receive runoffs from agricultural lands and effluents from industries. The levels of OCPs ranged from 5.5 (2,4-DDD) to 450 +/- 0.10 ng/l (beta-BHC) in water samples and from 0.6 (aldrin and 2,4-DDD) to 184 +/- 0.12 ng/g (beta-BHC) in sediments for triplicate analyses. Some endocrine disrupting OCPs such as DDT, DDE, heptachlor, endosulphan and the chlordanes were detected.     

Solid-phase microextraction and gas chromatography-electron capture detection analysis of trace organochlorine pesticides in water using novel benzo-15-crown-5 sol-gel coating

A novel dihydroxy-terminated benzo-15-crown-5 is synthesized and applied to prepare the solid-phase microextraction (SPME) fiber coating with sol-gel technology. Headspace SPME, as a simple, solvent-free method, is applied to the analysis of 16 organochlorine pesticides (OCPs) present at trace levels in a water sample. A homemade crown ether fiber coated with 80- micro m thickness was used for extraction. Analyses are performed using gas chromatography-electroncapture detection. The optimization of the extraction process is studied. Compared with commercially available SPME fibers, polydimethylsiloxane, the new phases show better selectivity and sensitivity toward OCPs. The linear concentrations range from 1 to 1000 ng/L, the detection limits are in the range of 0.01-0.5 ng/L, the recoveries are over 85%, and relative standard deviations are below 7.2% for these OCPs.     

On-line ion-pair solid-phase extraction-liquid chromatography-mass spectrometry for the analysis of quaternary ammonium herbicides

An ion-pair on-line solid-phase extraction procedure using C8 extraction disks, suitable for liquid chromatography-mass spectrometry analysis is developed to determine quaternary ammonium herbicides (quats) in water samples. The separation of these compounds was performed using ion-pair chromatography with heptafluorobutyric acid (15 mM, pH 3.3) and acetonitrile gradient elution. Detection was carried out using a quadrupole mass spectrometer. Water sample volumes up to 50 ml can be preconcentrated with recoveries higher than 70%. Good precision and accuracy (day-to-day and run-to-run) were obtained and the detection limits ranged from 6 to 85 ng l(-1). The proposed on-line ion-pair solid-phase method enables compliance with European Community directives for drinking waters (100 ng l(-1)).     

Automated analysis of geosmin, 2-methyl-isoborneol, 2-isopropyl-3-methoxypyrazine, 2-isobutyl-3-methoxypyrazine and 2,4,6-trichloroanisole in water by SPME-GC-ITDMS/MS

This paper describes a method of determining the following compounds in water characterised by complex matrices (raw waters and drinking waters): geosmin, 2-methylisoborneol (2-MIB), 2-isobutyl-3-methoxypyrazine (IBM), 2-isopropyl-3-methoxypyrazine (IPM) and 2,4,6-trichloroanisole (TCA). The method is carried out using headspace solid-phase microextraction (HS-SPME) combined with gas chromatography (GC) and ion trap mass spectrometry (ITMS). Several parameters of extraction and desorption were optimised through the use of a Combi PAL autosampler to automate various tasks (temperature extraction, extraction time, stir speed). Quantities of NaCl and the liquid volume/total volume ratio were also optimised. Double fragmentation (tandem MS/MS) was optimised on the target compounds. The method resulted in good linearity obtained for concentrations of 1 to 100?ng?L^?1 and provided detection limits of approximately below 1?ng?L^?1. Good precision (1–8%) was obtained. This method was successfully applied to the analysis of earthy and musty odours in municipal raw source waters with high concentrations of natural organic matter and in the corresponding treated waters. This is the first time MS/MS has been used to analyse odorous compounds in waters destined for human consumption. In addition, the method as developed is simple to use and lends itself to easy interpretation of chromatograms.     

Continuous solid-phase extraction and gas chromatographic determination of organophosphorus pesticides in natural and drinking waters

A simple, rapid continuous-flow solid-phase extraction method with gas chromatographic detection for the determination of organophosphorus pesticides is proposed. The continuous system consists of an adsorbent column where pesticides are preconcentrated and subsequently eluted with ethyl acetate. Various sorbent materials were assayed of which RP-C18 was found to provide the best results, with a sorption efficiency close to 100%. A comparative study of the determination of pesticides in aqueous samples was conducted using gas chromatography with nitrogen-phosphorus (NPD) and flame ionization (FID) detection. The detection limits of the method for 10 ml of sample were between 50-130 ng/l and 4.5-1 1.7 microg/l with NPD and FID detection, respectively. The method was used to determine organophosphorus pesticides in river, pond, well and tap waters, all with good precision (2.9-4.3%) and recoveries ranging from 93.8 to 104.5%.     

Determination of geosmin and 2-methylisoborneol in water using solid-phase microextraction and gas chromatography-chemical ionisation/electron impact ionisation-ion-trap mass spectrometry

A method for the determination of geosmin and 2-methylisoborneol (MIB) in water by solid-phase microextraction (SPME) is presented. Various SPME fibre chemistries have been compared for their efficiency in extracting MIB from water. Extraction conditions including the extraction time and temperature have been optimised. A 30 ml water sample is extracted for 20 min at 60 degrees C using a divinylbenzene fibre, and the extract analysed by gas chromatography with ion-trap mass spectrometry detection. d5-Geosmin and d3-MIB are added as internal standards to compensate for any variability in the SPME process which is not carried out to equilibrium. Chemical ionisation, using acetonitrile as the reagent gas, was found to give superior sensitivity to electron impact ionisation (EI) for the detection of MIB. EI was used as the ionisation mode for detection of geosmin. The method shows good linearity over the concentration range 5-40 ng l-1 and gives detection limits of 1 ng l-1 for both geosmin and MIB. Recovery (93-110%) and precision (3-12%) over this concentration range, for both raw and treated drinking waters, are comparable to currently employed methods such as closed-loop stripping analysis (CLSA). The method offers the advantage of being simple to use, with much shorter analysis times in comparison to CLSA.     

Supercritical fluid extraction and clean-up of organochlorine pesticides and polychlorinated biphenyls in mussels

The simultaneous extraction and clean-up of mussel samples followed by gas chromatography with electron-capture detection and mass spectrometric confirmation of 15 organochlorine pesticides (OCPs) and 11 polychlorinated biphenyls (PCBs) is developed using Florisil sorbent in the supercritical fluid extraction cell. The method detection limits vary from 1 to 10 ng/g for OCPs and from 2 to 15 ng/g for PCBs. Mean reproducibilities of 11% and 10% and mean recoveries of 80% and 53%, respectively, for OCPs and PCBs are obtained. The feasibility of the proposed supercritical fluid extraction method was confirmed by analyzing a certified reference material and mussels collected from Taiwan region. The method is simple, rapid and requires only small amounts of samples and solvents. It may serve as a screening protocol for the determination of OCPs and PCBs in mussels on a routine basis.     

Determination of major phenolic compounds in water by reversed-phase liquid chromatography after pre-column derivatization with benzoyl chloride

A simple reversed-phase LC method capable of detecting ng/ml quantities of phenolic compounds in water is described. Pre-column derivatization with benzoyl chloride is used for the separation and determination o-cresol, m-cresol, p-cresol, phenol, resorcinol, catechol and hydroquinone in water. The benzoyl derivatives formed within in 15 min, were extracted with dietyl ether, and then analyzed by liquid chromatography with UV detection at 232 nm. With a mobile phase of acetonitrile-tetrahydrofuran-water (54:6:40, v/v) the seven derivatives were eluted in 15 min. The detection limits were between 0.05 and 0.50 ng/ml for 50 ml of a standard water sample. The method was applied to the analysis of phenols in wine and river water. The recovery of the derivatives from pure water was 81-94% with relative standard deviations of 2.5-5.0%.     

Determination of antibiotic compounds in water by solid-phase extraction-high-performance liquid chromatography-(electrospray) mass spectrometry

We developed a sensitive method based on solid-phase extraction and high-performance liquid chromatography coupled to mass spectrometry using an electrospray interface for the determination of four tetracyclines and two quinolones in water. The method was applied to river, well and sewage-treatment-plant waters. For the solid-phase extraction of 1000 ml river water samples, recoveries were between 88 and 112% and limits of detection were as low as 4 and 6 ng l(-1). Recoveries were higher than 64% for 1000 ml well water samples for the majority of the compounds. For the influent and effluent of the sewage-treatment-plant sample volumes of 100 and 250 ml were extracted, respectively. The method developed allowed ciprofloxacin to be determined in samples from the influent and effluent of the sewage-treatment-plant at 0.58 and 0.60 microg l(-1), respectively.     

Determination of Mo, U and B in waters by electrothermal vaporization inductively coupled plasma mass spectrometry

A method for the determination of Mo, U and B in waters by inductively coupled plasma mass spectrometry, using an electrothermal vaporizer for sample introduction, is described. For Mo and U, NH(4)F was chosen as modifier and for B, synthetic sea water plus mannitol were used. The modifier effect was verified and the optimized pyrolysis and vaporization temperatures were obtained from pyrolysis and vaporization curves, together with the transient signals of the analytes. The masses of the modifiers added to the tube were also optimized. The detection limits were 0.018 or 0.30 ng ml(-1) for Mo, 0.03 ng ml(-1) for U and 0.68 ng ml(-1) for B. The analytes were determined in certified waters and the obtained results agree with the certified or recommended values or, in the case of B in sea waters, with the values obtained by other methods. Uranium could not be measured in the sea water samples due to strong memory effect.     

Low-level mercury determination with thiamine by fluorescence optosensing

A sensitive fluorescence optosensing method for the determination of Hg(II) in water samples is described. The method, using a flow injection technique, is based on the immobilization on a non-ionic-exchanger solid support (packed in a flow cell placed in a conventional fluorimeter) of the thiochrome formed by the oxidation of thiamine with Hg(II) in a continuous flow carrier at pH 8.1. Experimental parameters such as the solid support, the carrier pH, the thiamine concentration and the flow-rate were investigated to select the optimum operating conditions. The proposed optosensor showed a relative standard deviation of + 3.0% for ten replicates analysis of 100 ng ml(-1) of mercury(II). A detection limit of 3 ng ml(-1) for mercury(II) was achieved for 4-ml sample injections. A detailed study of interferences (possible elements present in natural waters) demonstrated that this optosensing method is virtually specific for this metal, because it allows the determination of mercury in the presence of relatively large amounts of other heavy metals and compounds present in natural waters, such as Mg(II) or Ca(II). The method was successfully applied to the determination of Hg(II) in spiked samples of mineral, tap and sea water.