Determination of trace elements in biological materials using tetramethylammonium hydroxide for sample preparation

A method to prepare milk powder, bovine liver and bovine muscle samples for analysis by electrothermal atomic absorption spectrometry (ETAAS) is proposed. Samples are mixed with a small amount of tetramethylammonium hydroxide (TMAH) and a stable and homogeneous slurry is produced in ca. 2 h with heating at 60–70 °C. After such sample preparation and dilution with water, trace elements are determined in certified reference materials. Pyrolysis and atomisation temperatures are optimised for each element, and several modifiers are investigated. External calibration is used for every analyte. Limits of detection (LODs), precision and accuracy are reported for Cd, Pb, Ni, Cr, Cu and Ag and compared with those obtained after conventional acid digestion. The main advantages of the proposed method are the simplicity of sample preparation and the longer lifetime of the graphite tube.     

Microwave digestion of biological samples with tetramethylammonium hydroxide and ethylenediaminetetraacetic acid for element determination

A microwave-digestion system with a closed PTFE vessel was used to improve the leaching of inorganic constituents from biological samples with tetramethylammonium hydroxide (TMAH) and ethylenediaminetetraacetic acid (EDTA). The effects of microwave parameter settings and the quantities of TMAH and EDTA used on leaching efficiency were evaluated. This new digestion method has been applied to the standard reference materials NIST SRM 1577 B Bovine Liver 1515 Apple Leaves and NIES CRM No. 1 Pepperbush, No. 3 Chorella, No. 6 Mussel and No. 7 Tea Leaves. The major and minor elements in the digests were analyzed by flame atomic absorption spectrometry or graphite furnace atomic absorption spectrometry. Good agreement of the analytical results with the certified values was obtained.     

Determination of mercury in biological materials by CV-AAS after wet digestion

The paper describes the determination of ultratrace concentrations of mercury in biological materials. Samples were digested in nitric acid under pressure in a polytetrafluoroethylene bomb. Mercury was determined in the digest solution by cold vapour atomic absorption spectrometry using stannous chloride reduction and two-stage gold amalgamation. The detection limit is 0.12 ng. Analysis of several certified reference materials yielded results in excellent agreement with the certified values. The results for blood serum of several subjects ranged from 0.2 to 0.8g 1^–1.Of the National Fund for Scientific Research (Belgium), to whom correspondence should be addressed     

Determination of major and trace elements in biological materials by microwave induced plasma optical emission spectrometry (MIP-OES) following tetramethylammonium hydroxide (TMAH) solubilization

A simple, alternative method to acid digestion is presented for the preparation of biological materials for major and trace elements by microwave induced plasma optical emission spectrometry (MIP-OES). Standard reference materials were solubilized using a methanolic solution of tetramethylammonium hydroxide (TMAH) by the application of ultrasonic agitation. Following dilution with water suspensions were pumped to a V-groove Babington-type nebulizer then into argon plasma. Limits of detection and precision are reported for major (Na, K, Ca, Mg) and trace (Cu, Fe, Sr, Zn) elements. Standard addition procedures were used to minimize possible matrix interferences. The method offers relatively good precision (R.S.D. ranged from 6 to 12%). Measured concentrations are in satisfactory agreement with certified values for the biological reference materials: TORT-1 (Lobster hepatopancreas), IAEA-153 (Milk powder) and NIST 1577 (Bovine liver). The simple procedure could be useful as a routine analysis of biological materials.     

Determination of trace elements and radioactive materials by substoichiometric isotope dilution analysis

Substoichiometric isotope dilution analysis has been applied for the determination of trace elements in liquid samples, of carrier content in radioisotope solution and of concentration of organic reagent. Cu in mineral acids and in ZnSe single crystal was determined by the substoichiometric extraction with dithizone. The values of 1.8 and 0.018 ppm in nitric acid and distilled one and of 1.4 and 0.44 ppm in ZnSe were obtained. Cu and P carrier contents in⁶⁴Cu and³²P solutions were determined by the substoichiometric extractions with dithizone in CCl₄ and with molybdic acid into MIBK in the series of the solutions adding various amounts of Cu or P carrier. An analogous method has been applied for the determination of dithizone and diethyldithiocarbamate solutions. The method was also applied for the determination of⁶⁰Co radioactivity in environmental samples. The analytical result of water samples is described.     

Determination of trace Cd and Pb in environmental and biological samples by ETV-ICP-MS after single-drop microextraction

A method based on single-drop microextraction (SDME) combined with electrothermal vaporization (ETV)-ICP-MS was proposed for the determination of trace Cd and Pb. 8-Hydroxyquinoline (8-HQ) was employed as extractant dissolved in several microliters of chloroform and then an organic microdrop was formed at the tip of the microsyringe needle to extract the interest analytes. The vaporization behavior of the metal-8-HQ chelates in graphite furnace was investigated, and the ETV temperature program was optimized. The factors that influenced the extraction efficiency of target analytes (including pH value, flow rate of sample, extraction time and organic microdrop volume) were studied. Under the optimum conditions, the detection limits of the Cd and Pb were 4.6 and 2.9 pg mL⁻¹ with the enrichment factor of 140-fold for Cd and 190-fold for Pb, respectively. The proposed method was applied successfully to the determination of trace Cd and Pb in environmental and biological samples. In order to validate the developed method, a certified reference material of GBW 08501 peach leaves was analyzed and the determined values obtained were in a good agreement with the certified values.     

Determination of cadmium in biological samples solubilized with tetramethylammonium hydroxide by electrothermal atomic absorption spectrometry, using ruthenium as permanent modifier

The feasibility of Ru as a permanent modifier for the determination of Cd in biological samples treated with tetramethylammonium hydroxide (TMAH) by ET AAS was investigated. The tube treatment with Ru was carried out only once and lasted for about 300 atomization cycles. The pyrolysis and atomization temperatures, 750 °C and 1300 °C, respectively, were chosen from the temperature curves. The sample dissolution procedure was very simple: a sample aliquot was mixed with a small volume of a 25% m/v TMAH solution, the volume was made up to 50 ml and the mixture was kept at 60 °C for 1 h. Six certified biological reference materials were analyzed and the obtained Cd concentrations are within the 95% confidence interval of the certified values, proving the accuracy of the proposed procedure for a variety of biological samples. The calibration curve, with correlation coefficient higher than 0.99, was established for a working range up to10 μg l⁻¹. The precision was good as demonstrated by relative standard deviations below 3%, except for one sample. The limit of detection (3σ) was 0.05 μg l⁻¹ and the characteristic mass was 1.30 pg, obtained in the presence of the Ru modifier.     

Determination of trace elements in biological materials by neutron activation and extraction with TOPO

Solvent extraction with TOPO from 6M hydrochloric acid is proposed as a method for the elimination of interfering activities in neutron activation analysis of biological material for trace elements. By this procedure²⁴Na,⁴²K,³²P,⁸²Br, and⁴⁷Ca are efficiently removed, and a number of trace element activities can be measured by Ge(Li) spectrometry. Chemical yields are determined by re-activation. Data for Cu, Zn, Mo, and Cd in two biological standards are presented.     

Determination of toxic elements in coal by ICP-MS after digestion using microwave-induced combustion

A microwave-induced combustion (MIC) procedure was applied for coal digestion for subsequent determination of As, Cd and Pb by inductively coupled plasma mass spectrometry (ICP-MS) and Hg using cold vapor (CV) generation coupled to ICP-MS. Pellets of coal (500 mg) were combusted using 20 bar of oxygen and ammonium nitrate as aid for ignition. The use of nitric acid as absorbing solution (1.7, 3.5, 5.0, 7.0 and 14 mol L⁻¹) was evaluated. For coal samples with higher ash content, better results were found using 7.0 mol L⁻¹ HNO₃ and an additional reflux step of 5 min after combustion step. For coal samples with ash content lower than 8%, 5.0 mol L⁻¹ nitric acid was suitable to the absorption of all analytes. Accuracy was evaluated using certified reference material (CRM) of coal and spikes. Agreement with certified values and recoveries was better than 95 and 97%, respectively, for all the analytes. For comparison of results, a procedure recommended by the American Society of Testing and Materials (ASTM) was used. Additionally, a conventional microwave-assisted digestion (MAD) in pressurized vessels was also performed. Using ASTM procedure, analyte losses were observed and a relatively long time was necessary for digestion (>6 h). By comparison with MAD procedure, higher sample mass can be digested using MIC allowing better limits of detection. Additionally, the use of concentrated acids was not necessary that is an important aspect in order to obtain low blank levels and lower limits of detection, respectively. The residual carbon content in digests obtained by MAD and MIC was about 15% and <1%, respectively, showing the better digestion efficiency of MIC procedure. Using MIC it was possible to digest completely and simultaneously up to eight samples in only 25 min with relatively lower generation of laboratory effluents.     

Determination of 25 elements in biological standard reference materials by neutron activation analysis

Trace element analysis has been carried out on standard biological reference samples such as bovine liver, orchard and tomato leaves. Computer aided instrumental neutron activation analysis and, in some cases, preliminary chemical group separation followed by NAA were used. For Ca, Mg, Ni and Si special chemical separation and Cerenkov counting were applied. *** DIRECT SUPPORT *** A1353068 00003     

Determination of trace elements in biological materials by instrumental epithermal neutron activation analysis

The use of reactor epithermal neutrons in instrumental activation analysis is described for the determination of trace elements via long-lived isotopes. A boron carbide filter is used. Results of analyses of human erythrocytes, plasma, urine and some biological reference materials are given to demonstrate the applicability of the method to biological samples. Bromine, iron, cesium, rubidium, selenium and zinc and cobalt are determined. The method provides accuracy and reliability similar to conventional thermal neutron activation but is faster. Limits of detection attainable with the two techniques are compared.     

Determination of plutonium by isotopic dilution mass spectrometry following TTA-extraction

Isotopic dilution mass spectrometry has been applied to assess the plutonium concentration in samples such as those obtained from the dissolution of irradiated uranium fuels in a reprocessing plant. Prior to the analysis, plutonium is taken through a redox cycle and is separated from uranium and fission products by extraction into TTA-xylene. The extraction procedure, the standardization of the spike solution and the mass assay of the plutonium are described; typical results under plant conditions are given. The overall precision of a single measurement of the plutonium concentration is 0.6%, expressed as relative standard deviation, including the plant sampling error, dilution error and analytical error.     

Determination of thallium by isotopic dilution method using substoichiometric displacement

A new analytical procedure for the determination of thallium in a wide concentration range has been developed. The method of direct isotopic dilution (IDA) using carrier-free²⁰²Tl and the formerly developed procedure of substoichiometric displacement have been used for the determination of thallium content in various types of analyzed samples e.g. minerals, sediments, ion-exchangers, hydrothermal waters, etc. in the concentration range from several percent to 10^?4%, or subsequently down to 0.01 μg/ml in waters. The results obtained are compared with those of emission spectrometry and activation analysis using (γ, n) reaction. A good agreement was found.     

电感耦合等离子体质谱法测定环境土壤中39种元素的内标选择研究

本文建立了四酸消解-ICP-MS测试分析方法,基于ICP-MS测试生态环境领域国家网土壤环境质量调查任务涵所盖的39种元素的内标选择进行了分析。建立“主要干扰权重”概念,对内标元素进行分析筛选,确定¹⁰³Rh 、¹¹⁵In 、¹⁸⁵Re、¹⁹³Ir作为环境土壤分析测试内标元素,试验表明：¹⁰³Rh、¹¹⁵In对于低质量段元素具有较好的校正效果,¹⁸⁵Re、¹⁹³Ir对于高质量段具有较好的校正效果。方法校准曲线的线性相关系数均大于0.999,方法检出限在0.001~2.9μg/g之间,该方法用GSS-8标准体土壤进行验证,GSS-8的RSD在1.7%~19.1%之间,加标回收率80%~121%。该分析方法具有较好的准确度和精密度,适合在国家网土壤环境质量调查任务中推广和使用。     

Accurate determination of selenium in biological materials without perchloric acid for digestion

Selenium (10–80 μg kg^?1) is determined by hydride-generation atomic absorption spectrometry in mixed diet, faecal and urine samples and in standard reference materials (bovine liver, rice flour, wheat flour and horse kidney) after two digestion procedures. No difference was found in digestion efficiency between a nitric/sulphuric acid mixture and a nitric/sulphuric/perchloric acid mixture. The results suggest that the digestion of most biological materials for the determination of selenium does not require the use of perchloric acid.     

Determination of strontium in biological materials by charged-particle activation analysis using the stable isotope dilution method

In order to apply the stable-isotope dilution method to charged-particle activation analysis, determination of strontium in biological materials has been studied by proton activation using isotopically enriched⁸⁶Sr as a spike. To avoid thermal decomposition of biological materials due to the low penetrating power of proton beam, and to eliminate interfering nuclear reactions due to the matrix elements, strontium in the sample and/or isotopic mixture as a comparator was separated chemically together with most of calcium before bombardment, and the fraction isolated was converted to a silica-gel pellet as a most suitable physical and chemical form for bombardment. By processing as above, it was demonstrated that the strontium contents in the biological materials can be determined accurately, precisely and easily. Through a series of experiments, the method was also proved to be applicable for charged-particle activation analysis.     

The development of a method for the determination of trace elements in fuel alcohol by ETV-ICP-MS using isotope dilution calibration

A method for the determination of Ag, Cd, Cu, Pb and Tl in fuel alcohol by isotope dilution electrothermal vaporization inductively coupled plasma mass spectrometry (ID ETV-ICP-MS) is proposed. The analytes were separated in two groups: Ag and Cu were determined without modifier and Cd, Pb and Tl with the use of Pd as chemical modifier. The employed ETV operational conditions were pyrolysis temperature of 800 °C for Cd, Pb and Tl and of 900 °C for Ag and Cu and vaporization temperature of 2400 °C for both groups. Seven common, one with additive and one anhydrous fuel ethanol samples were analyzed. The spiked and reference isotopes were, respectively, ¹⁰⁹Ag and ¹⁰⁷Ag, ¹¹²Cd and ¹¹¹Cd, ⁶³Cu and ⁶⁵Cu, ²⁰⁶Pb and ²⁰⁸Pb and ²⁰³Tl and ²⁰⁵Tl. The added amounts of the enriched isotope material were the same for all samples: 4.6 ng of ¹⁰⁹Ag, 5 ng of ¹¹²Cd, 21.1 ng of ⁶³Cu, 9 ng of ²⁰⁶Pb and 0.21 ng of ²⁰³Tl. The blank was bi-distilled ethanol, acidified with 0.3% (v/v) nitric acid, as the samples. The limits of detection (LODs) were calculated as three times the standard deviation of the concentrations in the blank (n = 10) and were, in μg L⁻¹, for Ag: 0.02, for Cd: 0.08, for Cu: 0.1, for Pb: 0.05 and for Tl: 0.001. The obtained concentrations in the samples were in agreement with those obtained by external calibration (EC), according to the paired t-test. The isotope dilution (ID) showed to be a robust, fast and simple calibration technique for the analysis of fuel ethanol.     

同位素稀释气相色谱-质谱法测定茶叶中5种杀菌剂残留

建立了使用固相萃取-气相色谱/质谱联用结合同位素稀释技术准确测定3种茶叶(红茶、绿茶和普洱茶)中敌菌丹、克菌丹、灭菌丹、百菌清和苯氟磺胺等杀菌剂农药残留的新方法。茶叶试样中加入同位素内标D6-克菌丹,经乙腈匀浆提取,提取液离心后取上清液经Forisil固相萃取柱浓缩、净化。GC-MS采用选择离子监测(SIM)模式进行定性定量分析,内标法定量。方法的添加回收率为74.1%～100.6%;相对标准偏差为1.2%～12%;6种农药的检出限为0.002～0.14μg/mL。     

Determination of trace elements in biological tissues by aluminum block digestion and spike-height flame atomic absorption spectrometry

A method for the determination of cadmium, copper, lead, and zinc in biological tissues using small volumes of digest is described. An aluminium heating block is used to digest samples and elements are determined by spike-height flame atomic absorption spectrometry. Interferences have been assessed and the sample decomposition procedure evaluated.     

Direct determination of mercury in cosmetic samples by isotope dilution inductively coupled plasma mass spectrometry after dissolution with formic acid

A new method was proposed for the accurate determination of mercury in cosmetic samples based on isotopic dilution (ID)-photochemical vapor generation (PVG)-inductively coupled plasma mass spectrometry (ICP MS) measurement. Cosmetic samples were directly dissolved in formic acid solution and subsequently subjected to PVG for the reduction of mercury into vapor species following by ICP MS detection. Therefore, the risks of analyte contamination and loss were avoided. Highly enriched ²⁰¹Hg isotopic spike is added to cosmetics and the isotope ratios of ²⁰¹Hg/²⁰²Hg were measured for the quantitation of mercury. With ID calibration, the influences originating from sample matrixes for the determination of mercury in cosmetic samples have been efficiently eliminated. The effects of several experimental parameters, such as the concentration of the formic acid, and the flow rates of carrier gas and sample were investigated. The method provided good reproducibility and the detection limits were found to be 0.6 pg mL⁻¹. Finally, the developed method was successfully applied for the determination of mercury in six cosmetic samples and a spike test was performed to verify the accuracy of the method.