Determination of zirconium using morin immobilized on silica gel

The sorption of 5,7,2′,4′-tetrahydroxyflavonol from butanol and acetone-hexane (1:4) solutions on highly dispersed silica was studied. A solid-phase reagent is proposed for the sorption-spectrophotometric determination of down to 30 μg/L of zirconium(IV).     

Sorption behaviour of nanocrystalline MOR type zeolite for Th(IV) and Eu(III) removal from aqueous waste by batch treatment

The nanocrystalline mordenite (MOR) type zeolite materials with initial chemical composition Na(2)O:Al(2)O(3):10SiO(2):48H(2)O have been synthesized under hydrothermal conditions. MOR1 and MOR2 are spherically shaped nanocrystals, whereas MOR3 and MOR4 have rod-like morphology. This paper reports the sorption characteristics of MOR analogues for Th(IV) and Eu(III) removal from aqueous nuclear waste. Sorption of Th(IV) and Eu(III) on MOR1, MOR2, MOR3 and MOR4 in a single component system with varying initial metal ion concentration, solution pH, contact times, sorbent dose and temperatures has also been investigated. Further, the Langmuir and Freundlich sorption models have been applied to describe equilibrium isotherms at different temperatures. The adsorption capacity increases largely with increasing solution pH and temperature of the system. Specific surface area and pore volume have been investigated by Brunauer-Emmett-Teller (BET) method. The N(2) adsorption isotherm presents a type IV isotherm with narrow hysteresis loop which indicates the presence of mesopores related to inter-particle voids. Thermodynamic results indicate that the sorption follows an endothermic physisorption process. It has been found that these exchangers have good sorption capacity and out of which MOR4 has highest sorption capacity. Thus, nanocrystalline MOR4 is proved to be good sorbent for both Th(IV) and Eu(III).     

A rapid extractive spectrophotometric method for the determination of tin in canned foods with 5,7-dichloro-8-quinolinol

A rapid method for the spectrophotometric determination of tin in canned foods, based on formation of the binary Sn(IV)-5,7-dichloro-8-quinolinol complex and extraction into chloroform has been developed. The absorption maximum at 390nm ( = 1.26 x 10(4) l.mole(-1).cm(-1)) is used for the determination. Beer's law is obeyed up to 6mug of tin per ml. Organic matter is destroyed by digestion with acid. Potential interferences have been studied. The detection limit for tin is 2.5mg kg .     

Sorption of palladium(II), rhodium(III), and platinum(IV) on Fe(3)O(4) nanoparticles

The adsorption of palladium(II), rhodium(III), and platinum(IV) from diluted hydrochloric acid solutions onto Fe(3)O(4) nanoparticles has been investigated. The parameters studied include the contact time and the concentrations of metals and other solutes such as H(+) and chloride. The equilibrium time was reached in less than 20 min for all metals. The maximum loading capacity of Fe(3)O(4) nanoparticles for Pd(II), Rh(III), and Pt(IV) was determined to be 0.103, 0.149, and 0.068 mmol g(-1), respectively. A sorption mechanism for Pd(II), Rh(III), and Pt(IV) has been proposed and their conditional adsorption equilibrium constants have been determined to be logK=1.72, 1.69, and 1.84, respectively. Different compositions of eluting solution were tested for the recovery of Pt(IV), Pd(II), and Rh(III) from Fe(3)O(4) nanoparticles. It was found that 0.5 mol L(-1) HNO(3) can elute all of the metal ions simultaneously, while 1 mol L(-1) NaHSO(3) was an effective eluting solution for Rh(III), and 0.5 mol L(-1) NaClO(4) for Pt(IV). In competitive adsorption, the nanoparticles showed stronger affinity for Rh(III) than for Pd(II) and Pt(IV).     

Removal of metal ions from aqueous solution by adsorption on the natural adsorbent CACMM2.

The adsorption of Cd2+, Cr3+, Cu2+, Fe3+, Ni2+, Pb2+ and Zn2+ from aqueous solution was used to study the sorption properties of the adsorbent CACMM2 extracted from a cactus. Quantitation of the cation concentrations was performed by HPLC with diode array detection using on-column complex formation with 8-hydroxyquinoline. Removal degree from 100 mg M(n+) l(-1) solutions followed the series: Cu>Cd>Fe>Ni>Cr>Zn. Henry and Freundlich constants were determined since adsorption did not reach saturation plateaux in the studied concentration interval. Sorption of chromium by CACMM2 was stronger than the sorption onto lignin, calcium oxalate and cellulose up to 1,000 mg Cr3+ l(-1). Copper and iron were desorbed to a greater extent, while lead adsorption was practically irreversible. CACMM2 was able to remove more than 83% of chromate in a freshly prepared and exhausted chromate commercial solution.     

An infrared study of CO adsorption on silica-supported Ru-Sn catalysts

CO adsorption on Ru-Sn/SiO(2) catalysts of various Sn/(Ru+Sn) ratios was examined by Diffuse Reflectance Infrared Fourier-Transform Spectroscopy (DRIFTS). The catalysts were prepared by the incipient wetness impregnation method. Catalysts were activated by H(2) reduction at 773 K. CO adsorbed on the catalysts shows spectra whose band frequencies are divided into three groups: (i) High Frequency Region (HFR), containing a band at 2065 cm(-1), (ii) Low Frequency Region 1 (LFR(1)), containing bands at 2040-2015 cm(-1), (iii) Low Frequency Region 2 (LFR(2)), containing bands at 1990 and 1945 cm(-1). The types of adsorbed CO species formed strongly depend on the ratio Sn/(Ru+Sn) in the catalyst, CO pressure and temperature of adsorption. Adsorption of CO on Ru sites in the Ru/SiO(2) catalyst results in LFR(1) bands at 2040-2015 cm(-1), which are independent of the CO pressure but the adsorption complexes are easily destroyed by raising the temperature. The addition of Sn to the catalyst creates new sites for CO adsorption. After adsorption at 298 K, the HFR band at 2065 cm(-1) and LFR(2) bands at 1990-1950 cm(-1) are observed. The relative intensities of these bands increase with increasing Sn-content in the samples. The LFR bands are thermally stable while the HFR band is not. The formation of the corresponding species is favored by increasing the CO pressure. Adsorbed CO species giving LFR(1) bands are assigned to linearly-adsorbed CO on the Ru(0) and/or on the Ru-Sn alloy sites. Adsorbed CO species giving HFR bands are assigned to CO adsorption on Ru(delta+)-O-Sn sites. After low temperature CO adsorption on samples with high Sn-content, only species that show bands at 1990 and 1945 cm(-1) in LFR(2) are observed.     

Layered microporous tin(IV) bisphosphonates

This article reports the hydrothermal synthesis and characterization of two new series of porous tin(IV) phosphonophenoxyphenylphosphonates with controlled pore size distributions, using as precursor the 4-(4'-phosphonophenoxy)phenyl phosphonic acid, [H2O3P-C6H4]2-O. Supermicroporous solids (S(BET), 300-400 m2 g(-1)) were obtained employing n-alcohol (C1-C6)-water mixtures (solvents ratio 1 : 1), in the presence of hydrofluoric acid. X-Ray powder diffraction shows that these compounds are semi-crystalline and the local environments around the phosphorus and tin elements have been studied by 31P and 119Sn MAS-NMR spectroscopy, respectively. The microstructure (particle sizes and shapes) of these phosphonates has been analyzed by scanning and transmission electron microscopy. This study shows that the microstructures of single-ligand (for instance tin(IV) phenylphosphonate) and cross-linked tin(IV) bisphosphonates are different. Tin(IV) phenylphosphonate crystallizes as micron-sized spheres, theta approximately 1-2 microm, formed by the aggregation of nanospheres, whereas tin(IV) bisphosphonates crystallize as microparticles larger than 20 microm. The textural properties of these porous solids were characterized by N2 and CO2 sorption isotherms. The key result of this work is that maxima of pore size distributions smoothly shift from 12 to 16 angstroms upon increasing the chain length of the alcohol. The microporosity of tin(IV) bisphosphonates is compatible with a double role played by the phosphonate groups acting as a pillar between adjacent layers and as a component of the hybrid organic-inorganic layers.     

A chelating resin containing 1-(2-thiazolylazo)-2-naphthol as the functional group; synthesis and sorption behavior for trace metal ions

A new polystyrene-divinylbenzene resin containing 1-(2-thiazolylazo)-2-naphthol (TAN) functional group was synthesized and its sorption behavior for 19 metal ions including Zr(IV), Hf(IV) and U(VI) was investigated by batch and column experiments. The chelating resin showed a high sorption affinity for Zr(IV) and Hf(IV) at pH 2. Some parameters affecting the sorption of the metal ions are detailed. The breakthrough and overall capacities were measured under optimized conditions. The overall capacities of Zr(IV) and Hf(IV) that were higher than those of the other metal ions were 0.92 and 0.87 mmol/g, respectively. The elution order of metal ions at pH 4 was evaluated as: Zr(IV)>Hf(IV)>Th(IV)>V(V)>Nb(V)>Cu(II)>U(VI)>Ta(V)>Mo(VI)>Cr(III)>Sn(IV)>W(VI). Quantitative recovery of most metal ions except Zr(IV) was achieved using 2 M HNO₃. Desorption and recovery of Zr(IV) was successfully performed with 2 M HClO₄ and 2 M HCl.     

Studies on the equilibrium uptake of some anions on a mixed and doped hydrous oxide

A mixed hydrous Fe(III)?Zr(IV) exhibits enhanced adsorption of anions in comparison to its constituent oxides. The uptake has been observed at pH 2.0, as a function of initial salt concentration and the product shows specific affinity for Cl^?, SO ₄ ^2? and PO ₄ ^3? ions. Doping the mixed oxide with Sn(II) improves its sorption capability for halide ions, while no significant enhancement is observed in the case of polyvalent anions.     

Synthesis of N,N′-dimethyl-N,N′-dibutyl malonamide functionalized polymer and its sorption affinities towards U(VI) and Th(IV) ions

A novel chelating polymeric material was synthesized by chemical anchoring of N,N′-dimethyl-N,N′-dibutyl malonamide (DMDBMA) with chloromethylated polystyrene-divinyl benzene polymer. The polymeric material thus prepared was characterized by ¹³C NMR, FT-IR spectroscopy and CHN elemental analysis. The fabricated polymeric material exhibited superior binding for hexa-valent and tetra-valent metal ions such as U(VI) and Th(IV). Various physico-chemical properties of the functionalized polymer like phase adsorption kinetics, metal sorption mechanism and metal sorption capacity was studied in the static method. Adsorption kinetics studies show that <20 min was sufficient for >99.99% adsorption of Th(IV) and U(VI). The kinetics for adsorption of U(VI) and Th(IV) was found to follow the first order Lagergren rate kinetics. Adsorption of U(VI) on the malonamide functionalized polymer followed the Langmuir adsorption isotherm. The Langmuir monolayer adsorption phenomenon was also confirmed by the theoretical approach calculated based on the adsorption kinetics. The metal sorption capacities for uranium and thorium were found to be 18.78 ± 1.53 mg and 15.74 ± 1.59 mg/g of the chelating polymer at 3 M HNO₃, respectively.     

Sorption of Th(IV) ions onto TiO2: Effects of contact time, ionic strength, thorium concentration and phosphate

Summary The sorption of Th(IV) onto TiO₂ was studied by the batch technique as a function of pH and ionic strength at moderate concentration (10^-4-10^-5 mol/l) and in the presence and absence of phosphate. It was found that the sorption rate of Th(IV) was relatively slow, the sorption percent was abruptly increased from pH 2 to 4, and the sorption was decreased with increasing ionic strength as a whole. In the concentration range of Th(IV) from trace concentration to 1.4 ^. 10^-4 mol/l and in the absence of phosphate, the sorption isotherms were roughly fitted the Freundlich equation at different ionic strengths and approximately constant pH. These sorption characteristics of Th(IV) onto TiO₂ were compared with those of uranyl on the same sorbent. In addition, the positive effect of phosphate on the sorption of Th(IV) onto TiO₂ was demonstrated obviously and can be attributed to strong surface binding of phosphate, and the subsequent formation of ternary surface complexes of Th(IV). The difference between the sorption characteristics of Th(IV) ions and uranyl ions onto TiO₂ is discussed.     

Organotin(IV) complexes of thiohydrazides and thiodiamines: synthesis, spectral and thermal studies

Organotin(IV) complexes of tribenzyltin(IV) chloride and di(para-chlorobenzyl)tin(IV) dichloride with thiohydrazides have been reported. The ligands synthesized were bidentate coordinating through sulphur and terminal nitrogen atoms. These form 1:1 metal-ligand complexes. The following organotin(IV) complexes have been synthesized: (C(6)H(5)CH(2))(3)Sn(L(1))Cl, (p-ClC(6)H(4)CH(2))(2)Sn(L(1))Cl(2), (C(6)H(5)CH(2))(3)Sn(L(1))Cl, (p-ClC(6)H(4)CH(2))(2)Sn(L(2))Cl(2), (C(6)H(5)CH(2))(3)Sn(L(3))Cl, (p-ClC(6)H(4)CH(2))(2)Sn(L(3))Cl(2), where (L(1)): 2-phenylethyl N-thiohydrazide, (L(2)): N-(2-phenylethyl-N-thio)-1,3-propane diamine, (L(3)): N-(2-phenylethyl-N-thio)-1,2-ethane diamine. The complexes were synthesized by directly mixing, refluxing and stirring the ligands with organotin(IV) chlorides in a suitable solvent. The complexes were found to be pure and were characterized by elemental analysis, electronic, infrared, (1)H and (13)C NMR spectroscopy. These complexes were also studied for their thermal decomposition by thermogravimetry (TG) and differential thermal analysis (DTA). Various kinetic and thermodynamic parameters, viz. activation energy (E(a)), order of reaction (n), apparent activation entropy (S(#)) and heat of reaction (DeltaH) have been determined by using Horowitz-Metzger method. It was observed that these complexes are highly stable and the thermal degradation of these complexes is a spontaneous process. The ligands and their tin complexes have also been screened for their fungitoxicity activity and found to be quite active in this respect.     

One-step preparation,structural assignment,and X-ray study of 2,2-di-n-butyl- and 2,2-diphenyl-6-aza-1,3-dioxa-2-stannabenzocyclononen-4-ones derived from amino acids

Twenty-four 2,2-di-n-butyl- and 2,2-diphenyl-6-aza-1,3-dioxa-2-stannabenzocyclononen-4-ones, each having a transannular N-->Sn bond, have been prepared by one-step reactions of alpha-amino acids (1 a-l), salicylaldehyde (2), and either di-n-butyltin(IV) oxide (3) or diphenyltin(IV) oxide (4). The new methodology constitutes an easy, highly efficient one-step synthesis of diorganotin(IV) derivatives, such as 5 a-l and 6 a-l, from iminic tridentate ligands without isolation of the Schiff bases. The structures of all the compounds have been established by a combination of (1)H, (13)C, (15)N, and (119)Sn NMR spectroscopy, IR spectroscopy, mass spectrometry, and elemental analysis. In all cases, the (119)Sn chemical shifts, as well as the (1)J((119)Sn,(13)C) coupling constants, are indicative of pentacoordinated tin atoms in solution. The structures of compounds 5 a, d, f, 6 a, b, b-racemic, c, d, f, g, and l have been established by single-crystal X-ray diffraction analyses. The tin atoms in 5 d, f, 6 a, b, b-racemic, c, d, g, and l each have a distorted trigonal-bipyramidal (TBP) geometry, with the oxygen atoms from the phenol and carboxylate moieties occupying the axial positions, and the imine nitrogen and phenyl or n-butyl substituents occupying the equatorial positions. Compounds 5 a and 6 f show distorted octahedral (DOC) geometries due to intermolecular coordination of the carbonyl oxygen to the tin atom, in a trans disposition to the N-->Sn bond, leading to trimeric 5 a and a polymeric structure for compound 6 f. Additionally, measurement of the one-bond coupling constants (1)J((119)Sn,(13)C) in diphenyltin(IV) complexes (6 a-l) and their correlation with the CSn-C bond angles has allowed the derivation of an equation that can be applied to assess the geometry around the tin atom for other diphenyltin(IV) compounds in solution.     

Separation of titanium, iron and aluminium on a chelating resin with benzoylphenylhydroxylamine group and application to bauxite and clay

Summary A chelating polystyrene based resin containing N-benzoyl-N-phenylhydroxylamine has been sythesized by two methods and characterized. Conditions for quantitative separation of Ti(IV), Fe(III) and Al(III) on the resin have been studied. A method has been developed for the determination of these three metal ions in bauxite or clay samples after their separation on the resin with recoveries of 98.5–99.5% for different metal ions. The maximum sorption values are observed at pH 1, 2.5 and 2.5 for Ti(IV), Fe(III) and Al(III), respectively, which are recovered by successive elution with 1 mol/l H₂SO₄, 2 mol/l HCl and 4 mol/l H₂SO₄ in the above order.     

An investigation of Re(VII) and Se(IV) adsorption by Tamusu clay: effect of time,pH, ionic strength,temperature and organic acids

By the batch method, the effects of contact time, pH, ionic strength, initial concentration, temperature on the sorption of Re(VII) and Se(IV) were investigated. Our results illustrated that Re(VII) and Se(IV) sorption was well described by the pseudo-second-order kinetic model, as well as by Freundlich model. This suggests chemical reaction as a rate-controlling step on the surface with 0.51 and 2.24 mg/g maximum sorption capacity at pH 7.0. The pH has little effect on Re(VII) adsorption, While it significantly affects the Se(IV) sorption. The sorption capacity of Re(VII) and Se(IV) decreased with increasing NaCl concentration. And the adsorption processes of Re(VII) and Se(IV) were endothermic spontaneous processes. What’s more, our results also show that the sorption of Re(VII) and Se(IV) in clay rock will not interfere with each other under various conditions. Additionally, the adsorption capacity of Se(IV) in clay is significantly increased under acidic conditions when organic acids in the solution, but not influenced under neutral and alkaline conditions.

     

Untersuchungen zur adsorptiven Anreicherung von Elementspuren an Adsorberharzen

Summary The adsorption behaviour of trace amounts of As(III), As(V), Fe(II), Hg(II), Pd(II), Pt(IV), Sb(V), Sn(II), Sn(IV) and Tl(III) from hydrochloric and hydrobromic acid solutions on Amberlite XAD-4 and XAD-7 resins by use of a chromatographic method was investigated. As expected, in certain acid concentrations, all of the elements are adsorbed partly or quantitatively. Furthermore, the adsorbability of 23 elements from sulphuric or hydrochloric acid solutions containing iodide or thiocyanate was examined. In accordance with analogous results for chloro- and bromocompounds it was found that the distribution behaviour of iodo- and thiocyanato-compounds is similar to that of corresponding solvent extraction systems. The adsorbed species of the trace compounds were estimated by comparison of the dependence of sorption rate on ligand concentration with the species distribution in the solution. The similarity of adsorbable and extractable species was discussed.

---

---

Teil II: Fresenius Z Anal Chem (1988) 331:588     

Complexation equilibria between niobium(V) and 4-(4'H-1',2',4'-triazolyl-3'-azo)-2-methylresorcinol Extraction-spectrophotometric determination of niobium in pyrochlore-bearing rocks

The complexation equilibria between niobium(V) and 4-(1'H-1',2',4'-triazolyl-3'-azo)-2-methylresorcinol has been studied by spectrophotometric methods and graphical and numerical calculation methods. The 1:2 Nb:R complex species formed at pH 6.2 ( = 2.16 x 10(4) l.mole(-1).cm(-1) at 490 nm) allows the determination of 0.15-2.50 ppm Nb. A 1:1 Nb:R complex species can be extracted into n-butanol from 0.1-1.5M hydrochloric acid ( = 1.28 x 10(4) l.mole(-1) .cm(-1) at 510 nm) and Beer's law is obeyed over the range 0.77-4.64 ppm Nb. Interferences and their elimination have been studied and the methods applied to the determination of niobium in pyrochlore-bearing ores.     

Rapid determination of organotin compounds by headspace solid-phase microextraction

Headspace solid-phase microextraction (SPME) followed by gas chromatography (GC) coupled to pulsed flame photometric detection have been investigated for the simultaneous speciation analysis of 14 organotin compounds, including methyl-, butyl-, phenyl-, and octyltins compounds. The analytical process (sorption on SPME fibre and thermal desorption in GC injection port) has been optimised using experimental designs. Six operating factors were considered in order to evaluate their influence on the performances of a SPME-based procedure. The evaluation of accuracy, precision and limits of detection (LODs) according to ISO standards and IUPAC recommendations has allowed the method to be validated. The LODs obtained for the 14 studied organotins compounds are widely sub-ng(Sn) l(-1). The precision evaluated using relative standard deviation ranges between 9 and 25% from five determinations of the analytes at 0.25-125 ng(Sn) l(-1) concentrations. The accuracy was studied throughout the analysis of spiked environmental samples. These first results show that headspace SPME appears really as attractive for organotins determination in the environment and the monitoring of their biogeochemical cycle.     

Determination of tin in canned foods by UV/visible spectrophotometric technique using mixed surfactants

The complex of tin(IV) with bromopyrogallol red (BPR) in the presence of nonyl phenoxy polyethoxyethanol (OP) and cetyltrimethylammonium bromide (CTAB) has a sensitive absorption peak at 304 nm. Under the optimal conditions, Beer's law is obeyed over the range 0.1-2.5 mug ml(-1) Sn(IV) with molar absorptivity being 8.2 x 10(4) l mol(-1) cm(-1) and detection limit 0.018 mug ml(-1). As compared with the visible method which also uses BPR as chromogenic reagent (lambda(max) = 550 nm), our method is sensitive and selective because of the complex's high, sharp absorption peak. In addition, the present method is simple and rapid, no heating or standing is needed. By means of the mixed surfactants the precipitation caused by the ion association of cetyltrimethylammonium cation and I(-)(3) anion is avoided if iodide is used for separating micro amounts of tin(IV) from a sample matrix. An application of the proposed method to the determination of Sn(IV) in a canned food was made with satisfactory results.     

Electro-oxidation of carbon monoxide on well-ordered Pt(111)/Sn surface alloys

The electro-oxidation of CO on model platinum-tin alloy catalysts has been studied by ex-situ electrochemical measurements following the preparation of the Pt(111)/Sn(2x2) and Pt(111)/Sn(radical3 x radical3)R30 degrees surfaces. A surface redox couple, which is associated with the adsorption/desorption of hydroxide on the Sn sites, is observed at 0.28 V(RHE)/0.15 V(RHE) in H(2)SO(4) electrolyte on both surfaces. Evidence that it is associated with the adsorption of OH comes from ex-situ photoemission measurements, which indicate that the Sn atoms are in a metallic state at potentials below 0.15 V(RHE) and an oxidized state at potentials above 0.28 V(RHE). Specific adsorption of sulfate anions is not associated with the surface process since there is no evidence from photoemission of sulfate adsorption, and the same surface couple is observed in the HClO(4) electrolyte. CO is adsorbed from solution at 300 K, with saturation coverages of 0.37 +/- 0.05 and 0.2 +/- 0.05 ML, respectively. The adsorbed CO is oxidatively stripped at the potential coincident with the adsorption of hydroxide on the tin sites, viz., 0.28 V(RHE). This strong promotional effect is unambiguously associated with the bifunctional mechanism. The Sn-induced activation of water, and promotion of CO electro-oxidation, is sustained as long as the alloy structure remains intact, in the potential range below 0.5 V(RHE). The results are discussed in the light of the requirements for CO-tolerant platinum-based electrodes in hydrogen fuel cell anode catalysts and catalysts for direct methanol electro-oxidation.