Synthesis, characterization and applications of pyrocatechol modified amberlite XAD-2 resin for preconcentration and determination of metal ions in water samples by flame atomic absorption spectrometry (FAAS)

A new chelating resin is prepared by coupling Amberlite XAD-2 with pyrocatechol through an azo spacer, characterized (by elemental analysis, IR and TGA) and studied for preconcentrating Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The sorption is quantitative in the pH range 3.0-6.5, whereas quantitative desorption occurs instantaneously with 2 M HCl or HNO(3) The sorption capacity has been found to be in the range 0.023-0.092 mmol g(-1) of resin. The loading half time (t(1/2)) is 1.4, 4.8, 1.6, 3.2, 2.3 and 1.8 min, respectively for Cd, Co, Cu, Fe, Ni and Zn. The tolerance limits of electrolytes NaCl, NaBr, NaNO(3), Na(2)SO(4) and Na(3)PO(4) in the sorption of all the six metal ions (0.2 mug ml(-1)) are reported. The Mg(II) and Ca(II) are tolerable with each of them (0.2 mug ml(-1)) up to a concentration level of 0.01-1.0 M. The enrichment factor has been found to be 200 except for Fe and Cu for which the values are 80 and 100, respectively. The lowest concentration of metal ion for quantitative recovery is 5, 10, 20, 25, 10 and 10 mug l(-1) for Cd, Co, Cu, Fe, Ni and Zn, respectively. The simultaneous determination of all these metal ions is possible and the method has been applied to determine all the six metal ions in tap and river water samples (RSD相似文献   

On-line preconcentration and determination of copper, lead and chromium(VI) using unloaded polyurethane foam packed column by flame atomic absorption spectrometry in natural waters and biological samples

A simple, sensitive and low cost, flow injection time-based method was developed for on-line preconcentration and determination of copper, lead and chromium(VI) at sub mug l(-1) levels in natural waters and biological samples. At the optimum pH, the on-line formed metal-ammonium pyrrolidine dithiocarbamate (APDC) complexes were sorbed on the unloaded commercial polyurethane foam (PUF), and subsequent eluted quantitatively by isobutylmethylketone and determined by flame atomic absorption spectrometry (FAAS). All chemical, and flow injection variables were optimized for the quantitative preconcentration of each metal and a study of interference level of various ions was also carried out. The system offered improved flexibility, low backpressure and applicability to all the studied metals. At a sample frequency of 36 h(-1) and a 60 s preconcentration time, the enhancement factor was 170, 131 and 28, the detection limit was 0.2, 1.8 and 2.0 mug l(-1), and the precision, expressed as relative standard deviation (s(r)), was 2.8 (at 10 mug l(-1)), 3.4 (at 50 mug l(-1)) and 3.6% (at 50 mug l(-1)) for Cu(II), Pb(II) and Cr(VI), respectively. The accuracy of the developed method was sufficient and evaluated by the analysis of certified reference materials and spiked water samples. Finally, the method was applied to the analysis of environmental samples.     

Preconcentration of trace metals on Amberlite XAD-4 resin coated with dithiocarbamates and determination by inductively coupled plasma-atomic emission spectrometry in saline matrices

Preconcentration of Cd(II), Cu(II), Mn(II), Ni(II), Pb(II) and Zn(II) in saline matrices on Amberlite XAD-4 resins coated with ammonium pyrrolidine dithiocarbamate (APDC) and piperidine dithiocarbamate (pipDTC) and subsequent determination by inductively coupled plasma atomic emission spectrometry were studied. Parameters such as effect of pH, effect of HNO(3) concentration on elution of metals from resin were studied. The results show that Amberlite XAD-4 coated with APDC was more efficient in the recovery of metal ions compared with Amberlite XAD-4 coated with pipDTC, in the concentration range of 0.1-200 mug l(-1), for 1 g of Amberlite XAD-4 coated resin. The detection limits for Cd(II), Cu(II), Mn(II), Ni(II), Pb(II), Zn(II) are 0.1, 0.4, 0.3, 0.4, 0.6, 0.5 mug l(-1), respectively, for resin coated with APDC and 0.7, 1.0, 0.8, 0.9, 1.7 and 1.2 mug l(-1) for resin coated with pipDTC. The effect of diverse ions on the determination of aforesaid metals was studied. The method was applied for the determination of trace metal ions in artificial sea water and natural water samples. The results were compared with extraction AAS method.     

Indirect atomic-absorption spectrophotometric determination of phosphorus after flotation as the ion-pair of molybdophosphate with bis[2-(5-chloro-2-pyridylazo)-5-diethylaminophenolato]cobalt(III)

An atomic-absorption spectrophotometric method has been developed for the indirect determination of phosphorus. The calibration graph is linear over the range 0.025-0.2 mug of phosphorus. The relative standard deviation is 1.3% for 0.2 mug of phosphorus (6 replicates). The method has been applied to the determination of phosphate in natural water samples. The enhancement effect of acetone on the determination is discussed.     

Manual and fia methods for the determination of cadmium with malachite green and iodide

A sensitive and rapid spectrophotometric method for the determination of cadmium is described, based on the formation of a blue complex at pH 4 between the anionic iodide complex of cadmium(II) and Malachite Green; the colour is stabilized with poly(vinyl alcohol). The calibration graph for measurement at 685 nm is linear over the range 1-50 mug of cadmium per 25 ml of final solution, with a relative standard deviation of +/-1.7% for 1 mug/ml cadmium. The molar absorptivity is 6.1 x 10(4) 1.mole(-1).cm(-1). The method can be successfully adapted for FIA, the peak height being proportional to the cadmium concentration over the range 0.1-3 mug/ml; a two-channel manifold is used and an improvement in selectivity is obtained. The use of a gradient tube is demonstrated to give a good calibration for Cd(II) over the range 2 x 10(-2) -2 x 10(-6)M.     

Determination of mono- and sesquiterpenes in water samples by membrane inlet mass spectrometry and static headspace gas chromatography

A membrane inlet mass spectrometric (MIMS) method is presented and compared with a static headspace gas chromatographic method (HSGC) for the determination of terpenes in water. The MIMS method provides a very simple and fast analysis of terpenes in water, detection limits being relatively low, from 0.2 mug l(-1) for monoterpenes to 2 mug l(-1) for geraniol. The analysis of terpenes by the HSGC (equipped with flame ionization detector, FID) method is more time-consuming and the detection limits (2 mug l(-1) for monoterpenes to 100 mug l(-1) for geraniol) are higher than with MIMS. However, the HSGC method has the advantage of determining individual mono- and sesquiterpene compounds, whereas MIMS provides only separation of different classes of terpenes. Both methods were applied to the analysis of mono- and sesquiterpenes in several condensation water samples of pulp and paper mills.     

Determination of cadmium in hair and blood by tungsten coil electrothermal atomic absorption spectrometry with chemical modifiers

Three chemical modifiers ((NH(4))(2)HPO(4), NH(4)H(2)PO(4), and Pd as Pd(NO(3))(2)) were evaluated for the determination of Cd in acid-digested solutions of hair and blood using electrothermal atomic absorption spectrometry in a tungsten coil atomizer (TCA). All modifiers caused some thermal stabilization of Cd when compared to the behavior observed in nitric acid medium. The best effects were observed in 15 mug ml(-)(1) Pd medium; the characteristic mass of Cd was 0.3 pg and the method detection limits were 0.009 mug g(-)(1) in hair and 0.2 mug l(-)(1) in blood. In addition to a slight thermal stabilization effect, Pd also increased the sensitivity for Cd by ca. 40% and the tungsten coil lifetime by 20% (i.e. from 300 to 360 heating cycles), reduced background signals, and eliminated condensed phase interferences caused by concomitants. The accuracy (3.2% as mean relative error in the Pd modifier) was checked for the determination of Cd in acid-digested solutions of certified reference materials of human hair and blood and by recoveries of Cd in spiked hair and blood samples by both TCA and a graphite furnace procedure. All results obtained in chemical modifiers are in agreement at a 95% confidence level.     

Rapid determination of zinc and iron in foods by flow-injection analysis with flame atomic-absorption spectrophotometry and slurry nebulization

A rapid method of determining zinc and iron in food by flame atomic-absorption spectrophotometry with slurry nebulization into an air-acetylene flame has been developed. A V-groove, clog-free Babington-type nebulizer, coupled to a single-line flow-injection analysis (FIA) system, was employed to introduce the slurry into the spray chamber. Under the FIA conditions described, an injection frequency of 120/hr is possible, with negligible carry-over and memory effects. The calibration graphs were obtained by using various concentrations (up to 0.1 g/ml) of white bean homogenate as standards, rather than solutions. The method has been applied to various kinds of foods, including grains, vegetables, fruits and sausage. Homogenization of semi-prepared samples to form slurries took only 4 min. Relative deviations between results by the slurry and solution methods for both elements averaged 2-3%. Detection limits by the slurry method were 0.3 mug/ml Zn and 0.6 mug/ml Fe.     

Electrothermal atomic absorption spectrometric determination of cadmium and lead with stabilized phosphate deposited on permanently modified platforms

Some drawbacks of the phosphate modifier such as reagent blank contribution and background absorption in electrothermal atomic absorption spectrometric determination of cadmium and lead are substantially alleviated by application of small amounts of phosphate, approximately 0.2 mumol (25 mug of NH(4)H(2)PO(4) or (NH(4))(2)HPO(4)), on the integrated platform of transversely heated graphite atomizer pre-treated with 2.7 mumol of Zr (250 mug) or W (500 mug) and 0.1 mumol of Ir (20 mug). Pyrolysis temperatures for Cd and Pb are up to 900 and 1100 degrees C for aqueous solutions and within 400-600 degrees C (Cd) and 750-850 degrees C (Pb) for biological fluids (urine, blood) and tissues (hair, liver, muscle) solubilized with tetraethylammonium hydroxide. The thermally stabilized phosphate on Zr-Ir or W-Ir treated platforms serves as a permanent modifier in analyses of environmental waters by multiple hot injections of large sample aliquots. Applications to water and biological certified reference materials are tabulated and show good agreement with certified values. Characteristic masses are 0.7-1.0 pg for Cd and 26-31 pg for Pb.     

A low consumption air-segmented sequential injection vapor generation system for the determination of mercury by atomic absorption spectrometry

A sequential injection system for the determination of mercury by vapor generation atomic absorption spectrometry (VGAAS) using tetrahydoborate reductant was developed, characterized by prevention of sample and reagent mixing in the holding coil using small air segments and initiation of the vapor generation in a flow-through gas-liquid separator. Extremely small volumes of reductant of 15-30 mul (0.2-1.0% NaBH(4)) and sample acidity as low as 0.05 mol l(-1) HCl were sufficient for achieving performance similar to flow injection (FI) VGAAS systems. A sample throughput of 90 h(-1) was achieved with 400 mul samples with a precision of 2.0% RSD at 10 mug l(-1)Hg, and a detection limit of 0.1 mug l(-1) (3sigma). Reagent consumption was reduced by a factor of 25 in comparison to the FI-VGAAS system. Good agreement with the certified value was obtained for the determination of mercury in seawater in a standard reference sample.     

Determination of arsenic, cadmium, lead and selenium in highly mineralized waters by graphite-furnace atomic-absorption spectrometry

A graphite-furnace AAS method using the stabilized-temperature platform furnace (STPF) concept, mixed palladium and magnesium nitrates as chemical modifier and Zeeman background correction has been applied to the direct determination of As, Cd, Pb and Se in highly mineralized waters used for medicinal purposes. These contain 20-40 g/l. concentrations of salts, mainly sodium and magnesium chlorides, bicarbonates and sulphates. The use of a pre-atomization cool-down step to 20 degrees in the graphite-furnace programme reduced the background absorption. Increasing the mass of magnesium nitrate modifier to 5 times that originally proposed improved the analyte peak shape. Under these conditions, no interference was found in analysis of the chloride/bicarbonate type of water, but the sodium and magnesium sulphate type of water had to be diluted, and even then an interference remained. Calibration with matrix-free standard solutions was used, but use of spike recovery is strongly recommended for testing the accuracy. The limits of determination (4.65sigma) of the proposed method for undiluted samples are 2.0 mug/l. for As, 0.05 mug/l. for Cd, 1.0 mug/l. for Pb and 1.5 mug/l. for Se.     

Simultaneous spectrophotometric determination of Fe and Ni with xylenol orange using principal component analysis and artificial neural networks in some industrial samples

Artificial neural networks (ANNs) are among the most popular techniques for nonlinear multivariate calibration in complicated mixtures using spectrophotometric data. In this study, Fe and Ni were simultaneously determined in aqueous medium with xylenol orange (XO) at pH 4.0. In this way, after reducing the number of spectral data using principal component analysis (PCA), an artificial neural network consisting of three layers of nodes was trained by applying a back-propagation learning rule. Sigmoid transfer functions were used in the hidden and output layers to facilitate nonlinear calibration. Adjustable experimental and network parameters were optimized, 30 calibration and 20 prediction samples were prepared over the concentration ranges of 0-400 mug l(-1) Fe and 0-300 mug l(-1) Ni. The resulting R.S.E. of prediction (S.E.P.) of 3.8 and 4.7% for Fe and Ni were obtained, respectively. The method has been applied to the spectrophotometric determination of Fe and Ni in synthetic samples, some Ni alloys, and some industrial waste waters.     

Determination of cadmium, lead and copper in water samples by flame atomic-absorption spectrometry with preconcentration by flow-injection on-line sorbent extraction

Cadmium, lead and copper were determined in synthetic sea-water, drinking water and the NBS 1643b Trace Elements in Water standard reference material at mug/l. levels by flame atomic-absorption spectrometry after on-line preconcentration by sorbent extraction with a flow-injection system. Bonded silica with octadecyl functional groups packed in a micro column of 100 mul capacity was used to collect diethylammonium diethyldithiocarbamate complexes of the heavy metals in the aqueous samples. The sample loading time was 20 sec at a flow-rate of 3.3 ml/min. Ethanol or methanol was used to elute the adsorbed analytes into the spectrometer. The sample loading rate, elution rate and pH were optimized. Enrichment factors of 19-25 for Cd, Pb and Cu were achieved at sampling frequencies of 120/hr with precisions of 1.4, 1.0 and 1.3% rsd (n = 11), respectively. The detection limits (3sigma) for Cd, Pb and Cu were 0.3, 3 and 0.2 mug/l., respectively. Determination of Cd, Pb and Cu in NBS SRM 1643b showed good agreement with the certified values. Recoveries of Cd and Pb added to sea-water were 95 and 102%, respectively.     

Determination of nickel by anodic adsorptive stripping voltammetry with a cation exchanger-modified carbon paste electrode

The behavior of a modified carbon paste electrode (CPE) for nickel determination by anodic adsorptive stripping voltammetry (AAdsSV) was studied. The electrode was built incorporating the Dowex 50W x 12 (H(+) form) ion exchanger to a Nujol-graphite base paste. Ni(2+) was preconcentrated on the electrode surface in open circuit conditions, with the reduction (-1300 mV)/reoxidation step carried out in HCl solution (pH 3). During deposition time (5 min), the hydrogen evolution did not present obstacle in the quantification of nickel. For 12 min of accumulation and 5 min of deposition, nickel can be quantified up to 600 mug l(-1). The detection limit was 0.005 mug l(-1) at a linear potential scan rate of 200 mV s(-1). Interferences from Hg(2+) and Ag(2+) up to a concentration of 1 and 0.6 mg l(-1), respectively, were eliminated with the aid of the anion exchanger Dowex-2 (mesh 200-400) which was added to the sample in the preconcentration step. The tolerance for some metal ions such as Cu(2+), Cd(2+), Fe(3+), Zn(2+), Co(2+) and Pb(2+) was improved in the same way. The method was applied for the determination of nickel in samples of tap and mineral water. At the concentration level of 50 mug l(-1) of Ni (2+), the results were in good agreement with those obtained using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). For a Ni(2+) concentration of 5 mug l(-1), the results obtained showed better accuracy than those obtained by ICP-AES.     

Spectrophotometric determination of isoproturon using p-aminoacetophenone and its application in environmental and biological samples

A simple and sensitive method for the determination of isoproturon, a widely used herbicide is described here which is based on alkaline hydrolysis of isoproturon to its corresponding primary amine followed by diazotization and coupling with p-aminoacetophenone in alkaline medium. The absorption maxima of the coloured compound formed is measured at 525 nm. Beer's law is obeyed over the concentration range of 0.5-5.0 mug in a final solution volume of 25 ml (0.02-0.2 ppm). The molar absorptivity and Sandell's sensitivity were found to be 8.6x10(5) l mol(-1) cm(-1) and 0.0002 mug cm(-2), respectively. The method has been satisfactorily applied to the determination of isoproturon in environmental and biological samples.     

Determination of bismuth in biological samples using on-line flow-injection microwave-assisted mineralization and precipitation/dissolution for electrothermal atomic absorption spectrometry

An on-line automated flow injection system with microwave-assisted sample digestion for the electrothermal atomic absorption spectrometric determination of bismuth in biological materials is described. After the exposure of the sample to microwave radiation, the analyte was subject to a precipitation/dissolution process. Bismuth was precipitated with the stannite ion in basic medium and collected on the walls of a knotted coil, while the other matrix components flowed downstream to waste. The precipitate was dissolved with nitric acid and a sub-sample was collected in a capillary of a sampling arm assembly, to introduce 20 mul volumes into the graphite tube by means of positive displacement with air through a time-based injector. The analytical figures of merit were first evaluated by filling the sampling arm with a standard solution of bismuth and thereafter injecting aliquots of this solution into the atomizer. The calibration graph was linear from the detection limit (8 pg) to 1.2 ng of bismuth. The sensitivity was of 26.8 mug l(-1) for 0.2 A-s and the characteristic mass (m(o)) was of 11.8 pg/0.0044 A-s. The precision of the method, evaluated by replicate analyses of solutions containing 20 and 200 pg of bismuth, were 5.5 and 3.0% (n=10), respectively. When solutions were introduced in the flow system here described, the calibration graph was linear in the range 0.04-6.0 mug l(-1), which means that a preconcentration factor of 10 was obtained for bismuth. The precision slightly deteriorated, e.g. the replicate analysis of solutions containing 1 and 10 pg of bismuth were 7.1 and 5.3% (n=10), respectively. However, the recoveries values obtained with urine and whole blood bismuth spiked samples were over 96.5% and the agreement between observed and certified values was good.     

Simultaneous spectrofluorimetric determination of europium, dysprosium, gadolinium and terbium using chemometric methods

A spectrofluorimetric method for the simultaneous determination of dysprosium, europium, gadolinium and terbium in ternary and quaternary mixtures by the use of pyridine-2,6-dicarboxylic acid as a chelating agent was developed. The influence of chemical variables affecting the analytical reaction was evaluated. A partial least-squares procedure and PC Quant software were used to assess data obtained from a variable number of calibration solutions and wavelengths. The ensuing method was validated by applying it to the analysis of synthetic ternary (Eu-Dy-Tb) and quaternary mixtures (Eu-Dy-Gd-Tb) over the concentration ranges 60-550 mug Eu l(-1), 30-400 mug Dy l(-1) and 30-400 mug Tb l(-1) in the former, and 20-220 mug Eu l(-1), 20-235 mug Dy l(-1), 25-230 mug Gd l(-1) and 75-230 mug Tb l(-1) in the latter. The results obtained by using the two quantitation procedures are compared. The relative errors in the determinations were less than 8% in most cases.     

Direct determination of gallium on polyurethane foam by X-ray fluorescence

Gallium chloride is easily extracted from 6M HCl by comminuted polyether-type polyurethane foam. After the extraction step, the gallium absorbed by the PU foam can be quantitatively determined by X-ray fluorescence. A procedure for the direct determination of gallium absorbed by PU foam by XRFS is thus described. Gallium is determined at levels as low as 60 ng/ml (C(L)), with a calibration sensitivity of 424 cps ml/mug, within a linear range 0.1-2.30 mug/ml. The procedure investigated was successfully applied to determination of gallium in aluminum alloys, bauxite and industrial residue samples.     

Spectrophotometric flow-injection determination of nickel in biological materials

A flow injection method has been developed for the direct determination of free available Pb(II) and total Pb content in wine samples. The method is based on the chemical sorption of Pb(II), from pH 7 buffered solutions, on a packed polyurethane foam column, modified by addition of 2-(2-benzothiazolylazo)-p-cresol (BTAC). After this step, lead was directly eluted with a stream of 0.1 mol l(-1) HCl into an air C(2)H(2) flame in which lead was determined by atomic absorption spectrometry. Total lead was analyzed after sample digestion with nitric acid and hydrogen peroxide, being free available lead determined by direct sample on-line preconcentration and elution. The method provides a limit of detection (3sigma) of 1 mug l(-1) lead and relative standard deviation, which varies from 6 to 0.7% for lead concentration of 10 and 500 mug l(-1). Total content of lead in wine samples analyzed varied from 8 to 42 mug l(-1) being obtained free available values of Pb(II) under the limit of detection of the method. Recovery studies on natural wine samples, spicked with inorganic lead, evidenced the remaining capability of ligands, present in the wine, to avoid lead retention on the polyurethane foam loaded with BTAC.     

Determination of clenbuterol in pharmaceutical preparations by reaction with o-phthalaldehyde using a flow-injection fluorimetric procedure

A new procedure for the determination of clenbuterol is proposed using flow-injection and fluorimetric detection. The method is based on the derivatization reaction of the primary amine group with o-phthalaldehyde in the presence of 2-mercaptoethanol. The calibration graph based on peak area was linear in the range 0.2-5 mug ml(-1) and the detection limit was 0.06 mug ml(-1). The method was validated using a reference spectrophotometric procedure and was applied to the determination of the drug in commercial pharmaceutical preparations.