Flow system exploiting multicommutation to increase sample residence time for improved sensitivity. Simultaneous determination of ammonium and ortho-phosphate in natural water

A flow system for the simultaneous determination of ammonium and phosphate in river water at the mug ml(-1) level employing a low expensive LED-based photometer is described. The manifold of the flow system comprised four analytical pathways containg a set of three-way solenoid valves and an automatic injector commutator. The signal measurements of both analytes were carried out using two LED-based photometers attached to the flow cells. A microcomputer running a programme written in quickbasic 4.5 provided facilities to control the system and to carry out simultaneously two analytical procedures also performing data acquisition. For the determination of ortho-phosphate the method based on reaction with molybdate and ascorbic acid was employed, while for ammonium the method based on reaction with hypochlorite and salicylic acid was selected. The four-pathway structure of the manifold allowed the sample incubation time to be increased to 130 s to permit the reaction to occur without a decrease in sample throughput. The usefulness of the system was ascertained by analyzing a set of water samples. Applying the paired t-test to results obtained employing reference methods, no significant difference at the 95% confidence level was observed for both analytes. Other profitable features such as an analytical throughput of 112 analyte determination per hour; relative standard deviations of 1.1 and 0.7% (n=6) ammonium and phosphate, respectively, reagent consumption of 0.3 mg ammonium molybdate, 0.75 mg salicylic acid, 3.3 mg ascorbic acid and sodium hypochlorite per determination; detection limits of 7.0 mug l(-1) NH(4)(+) and 17.0 mug l(-1) PO(4)(3-) were also achieved.     

Enhanced spectrophotometric determination of chromium (VI) with diphenylcarbazide using internal standard and derivative spectrophotometry

In the present work, erioglaucine A was applied as internal standard to enhanced spectrophotometric determination of chromium (VI) with diphenylcarbazide. The following procedure was used: (1) addition of internal standard and formation of ion pairs of Cr (VI) with benzyltributylammonium bromide (BTAB) (sample volume 100 ml), (2) extraction to 10 ml of methylene chloride, (3) evaporation in nitrogen stream, and (4) redissolution in a micro-volume with addition of diphenylcarbazide for color development (final volume 200 mul). The preconcentration factor achieved was about 400 and it was shown that, using internal standard, the analytical errors due to sample treatment were reduced. The analytical signals for chromium and internal standard were obtained at 591.30 and 653.50 nm from first derivative spectra, normalized against (1)D(653.50nm). The analytical characteristics evaluated were: detection limit = 0.06 mug l(-1), quantification limit = 0.19 mug l(-1), precision for 1 mug l(-1) 14.2%, and for 10 mug l(-1) 3.2%, correlation coefficient of linear regression was 0.9985. The proposed procedure was applied to determination of chromium (VI) in tap water. Total chromium was determined by electrothermal atomic absorption spectrometry, the recovery of hexavalent chromium added was then evaluated and compared with the results of the proposed procedure. In this experiment, good agreement was obtained between results obtained by the two methods.     

Determination of lead by on-line solid phase extraction using a PTFE micro-column and flame atomic absorption spectrometry

A rapid and sensitive time-based flow injection (FI) method for on-line preconcentration and determination of lead by flame atomic absorption spectrometry (FAAS), using polytetrafluoroethylene (PTFE) turnings as packing material in a micro-column, has been developed. The sample was mixed on-line with ammonium pyrrolidine dithiocarbamate (APDC) and the non-charged Pb(II)-PDC complex was absorbed quantitatively on the hydrophobic PTFE material, at a pH range 1.4-3.2. The preconcentrated complex was effectively eluted with isobutyl methyl ketone (IBMK) and introduced into the nebulizer-burner system. A nested coil (NC) is proposed for parking the eluate temporarily, in order to enable different elution and nebulization flow rates. With 180 s preconcentration time the sample frequency was 15 h(-1), and the enhancement factor was 330 at 13.0 ml min(-1) sample flow rate. The detection limit was c(L)=0.8 mug l(-1), the relative standard deviation (R.S.D.) 2.6% at the 30 mug l(-1) level and the calibration curve was linear over the concentration range 1.6-100 mug l(-1). The proposed method was evaluated by analyzing certified reference materials of water, sediments and fish tissue. Finally, it was applied successfully to the analysis of various environmental samples.     

On-line solid phase extraction system using PTFE packed column for the flame atomic absorption spectrometric determination of copper in water samples

A new flow injection on-line adsorption preconcentration system adapted to flame atomic absorption spectrometry (FAAS) for copper determination at the mug l(-1) level was developed. Polytetrafluoroethylene (PTFE) turnings packed in a mini-column were used as sorbent material. The copper ammonium pyrrolidine dithiocarbamate (APDC) complex was sorbed on the PTFE turnings, from which it could be eluted on-line instantly by isobutyl methyl ketone (IBMK) into the flame at a flow rate of 2.3 ml min(-1). The system was optimized and offered good performance characteristics with practically unlimited life time, greater flow rates and improved flexibility, as compared with other sorbent materials and the knotted reactor preconcentration systems. With 1 min preconcentration time, and a sample frequency of 40 h(-1), the enhancement factor was 340, which could be further improved by increasing the preconcentration time. The detection limit was c(L)=0.05 mug l(-1), and the precision was 1.5%, at the 2.0 mug l(-1) Cu level. The method has been applied successfully to the analysis of potable, river and seawater, and its accuracy was tested by the analysis of certified reference materials and by recovery measurements on spiked samples. No significant interferences exist from other substances usually occurring in natural water.     

On-line preconcentration and determination of copper, lead and chromium(VI) using unloaded polyurethane foam packed column by flame atomic absorption spectrometry in natural waters and biological samples

A simple, sensitive and low cost, flow injection time-based method was developed for on-line preconcentration and determination of copper, lead and chromium(VI) at sub mug l(-1) levels in natural waters and biological samples. At the optimum pH, the on-line formed metal-ammonium pyrrolidine dithiocarbamate (APDC) complexes were sorbed on the unloaded commercial polyurethane foam (PUF), and subsequent eluted quantitatively by isobutylmethylketone and determined by flame atomic absorption spectrometry (FAAS). All chemical, and flow injection variables were optimized for the quantitative preconcentration of each metal and a study of interference level of various ions was also carried out. The system offered improved flexibility, low backpressure and applicability to all the studied metals. At a sample frequency of 36 h(-1) and a 60 s preconcentration time, the enhancement factor was 170, 131 and 28, the detection limit was 0.2, 1.8 and 2.0 mug l(-1), and the precision, expressed as relative standard deviation (s(r)), was 2.8 (at 10 mug l(-1)), 3.4 (at 50 mug l(-1)) and 3.6% (at 50 mug l(-1)) for Cu(II), Pb(II) and Cr(VI), respectively. The accuracy of the developed method was sufficient and evaluated by the analysis of certified reference materials and spiked water samples. Finally, the method was applied to the analysis of environmental samples.     

A low consumption air-segmented sequential injection vapor generation system for the determination of mercury by atomic absorption spectrometry

A sequential injection system for the determination of mercury by vapor generation atomic absorption spectrometry (VGAAS) using tetrahydoborate reductant was developed, characterized by prevention of sample and reagent mixing in the holding coil using small air segments and initiation of the vapor generation in a flow-through gas-liquid separator. Extremely small volumes of reductant of 15-30 mul (0.2-1.0% NaBH(4)) and sample acidity as low as 0.05 mol l(-1) HCl were sufficient for achieving performance similar to flow injection (FI) VGAAS systems. A sample throughput of 90 h(-1) was achieved with 400 mul samples with a precision of 2.0% RSD at 10 mug l(-1)Hg, and a detection limit of 0.1 mug l(-1) (3sigma). Reagent consumption was reduced by a factor of 25 in comparison to the FI-VGAAS system. Good agreement with the certified value was obtained for the determination of mercury in seawater in a standard reference sample.     

Preconcentration of lead complexed with O,O-diethyl-dithiophosphate by column solid-phase extraction using different sorbents in a flow injection system coupled to a flame atomic absorption spectrometer

A comparative study of C(18) immobilized on silica, activated carbon and a polyurethane foam, as sorbents for Pb complexed with O,O-diethyl-dithiophosphate in a flow injection preconcentration system is reported. The complex was formed in 1.0 M HCl medium and processed in a simple system using a peristaltic pump, a manual injector-commutator and a mini-column filled with the sorbent. Using ethanol as eluent, the richest 150-mul fraction was collected and measured (after discarding 150, 200 and 0 mul for the activated carbon, foam and C(18), respectively) by flame atomic absorption spectrometry. The optimum concentration of the complexing agent was 0.05% m/v for C(18) and 0.2% m/v for the activated carbon and the polyurethane foam. The best sample loading flow rate was 4.0 ml min(-1) for the activated carbon and 2.0 ml min(-1) for C(18) and the polyurethane foam, while the best elution flow rate was 1.0 ml min(-1) (activated carbon) and 0.6 ml min(-1) (C(18) and foam). It was found that beyond a certain loading sample volume, for a constant analyte mass, the signal decreased. The maximum loading sample volume, for a constant analyte mass, before the signal started to decrease, was 50 ml for the activated carbon and 150 ml for the other materials. By processing 25 ml, the enrichment factors were 23, 55 and 166 for the activated carbon, foam and C(18), respectively. The best limit of detection (3sigma) was 0.3 mug l(-1) for the C(18) (1.2 mug l(-1) for the foam and 3 mug l(-1) for the activated carbon). As shown, the C(18) has a much superior retention performance in comparison to the other two materials.     

Flame atomic absorption spectrometric determination of chromium(VI) by on-line preconcentration system using a PTFE packed column

A new, sensitive and robust time-based flow injection (FI) method for on-line preconcentration and determination of ultra trace amounts of chromium(VI) by flame atomic absorption spectrometry (FAAS) has been elaborated. The sample is initially mixed on-line with ammonium pyrrolidine dithiocarbamate (APDC) and the Cr(VI)-PDC chelate is absorbed quantitatively on a mini-column packed with polytetrafluoroethylene (PTFE) turnings at a pH range 0.8-1.4. The complex is subsequently eluted with isobutyl methyl ketone (IBMK) and introduced directly into the nebulizer-burner system. The optimized system offered improved performance characteristics, with unlimited lifetime of the proposed column. The enhancement factor was 80, for a 3-min preconcentration time and the sample frequency was 18 h(-1). The calibration curve was linear over the concentration range 1-40 mug l(-1) with a detection limit of c(L)=0.8 mug l(-1) and a relative standard deviation of s(r)=3.2%, at the 20 mug l(-1) level. The proposed method was evaluated by analyzing samples of certified and spiked water, and it was applied to the analysis of natural water samples and sediments.     

中空纤维液相微萃取-高效液相色谱法测定水中残留的氨基甲酸酯类农药

应用中空纤维液相微萃取(HP-LPME)技术建立了水样中呋喃丹、西维因、异丙威和乙霉威的高效液相色谱分析方法。对影响HP-LPME的实验条件进行了优化。采用Accurel Q3/2聚丙烯中空纤维,以甲苯为萃取溶剂,于室温、搅拌速度为720 r/min条件下在4.5 mL样品溶液中萃取20 min,萃取物在室温下经氮气流吹干后用流动相溶解进样。采用Baseline C18分离柱(4.6 mm×250 mm,5.0 μm),以甲醇-水(体积比为60∶40) 为流动相,流速为1.0 mL/min。呋喃丹、西维因、异丙威和乙霉威的检测波长分别为200,223,200和208 nm。该方法对4种氨基甲酸酯类农药的富集倍数均大于45倍;4种氨基甲酸酯类农药在10~100 μg/L质量浓度范围内,其质量浓度与峰面积之间有良好的线性关系,相关系数均大于0.99;呋喃丹、西维因、异丙威和乙霉威的检出限(S/N=3)分别为5,1,5和3 μg/L;实际水样中的加标回收率为82.0%~102.2%,相对标准偏差为2.0%～6.2%(n=6)。     

Determination of the pesticide carbaryl by chemical deoxygenation micellar-stabilized room temperature phosphorescence

This paper presents a convenient determination method for carbaryl in polluted water by micellar-stabilized room temperature phosphorescence with Na(2)SO(3) as oxygen scavenger. The effect of various experimental conditions on the determination of carbaryl is discussed in detail. The analytical curve of carbaryl gives a linear dynamic range of 2 x 10(-7)-6 x 10(-5) mol/l., and a detection limit of 2 x 10(-7) mol/l. A recovery of 90-100% was obtained for 0.05-0.1 ppm carbaryl.     

Flow injection hydride generation electrothermal atomic absorption spectrometry with in-atomizer trapping for the determination of lead in calcium supplements

Lead hydride was generated from acid solution, containing potassium ferricyanide as an oxidizing agent, by the reaction with alkaline borohydride solution. The effects of reaction conditions (hydrochloric acid, ferricyanide and borohydride concentrations), and the lengths of reaction and stripping coils were studied. The effects of trapping temperature and argon flow rate were also investigated. Under the conditions giving the best peak area sensitivity, the detection limit (concentration giving a signal equal to three S.D. of the blank signal) was 0.12 mug l(-1) for a 1000 mul injection volume. The detection limit was improved to 0.03 mug l(-1) when the ferricyanide was purified by passage through a cation-exchange resin. Two calcium supplement materials were analyzed by the flow injection (FI)-hydride generation (HG)-electrothermal atomization atomic absorption spectrometry (ETAAS) method, giving values of 0.55 and 0.66 mug g(-1), in agreement with results obtained by previously validated methods. For a 500-mg sample the limits of detection and quantification were 0.006 and 0.02 mug g(-1), respectively.     

Simultaneous spectrofluorimetric determination of europium, dysprosium, gadolinium and terbium using chemometric methods

A spectrofluorimetric method for the simultaneous determination of dysprosium, europium, gadolinium and terbium in ternary and quaternary mixtures by the use of pyridine-2,6-dicarboxylic acid as a chelating agent was developed. The influence of chemical variables affecting the analytical reaction was evaluated. A partial least-squares procedure and PC Quant software were used to assess data obtained from a variable number of calibration solutions and wavelengths. The ensuing method was validated by applying it to the analysis of synthetic ternary (Eu-Dy-Tb) and quaternary mixtures (Eu-Dy-Gd-Tb) over the concentration ranges 60-550 mug Eu l(-1), 30-400 mug Dy l(-1) and 30-400 mug Tb l(-1) in the former, and 20-220 mug Eu l(-1), 20-235 mug Dy l(-1), 25-230 mug Gd l(-1) and 75-230 mug Tb l(-1) in the latter. The results obtained by using the two quantitation procedures are compared. The relative errors in the determinations were less than 8% in most cases.     

Chromium speciation by a surfactant-coated alumina microcolumn using electrothermal atomic absorption spectrometry

A simple and convenient method has been developed for the speciation of chromium(III) and chromium(VI) in aqueous solutions using a sodium dodecyl sulphate coated alumina micro-column (1.5 cm x 5 mm i.d.) and graphite furnace-atomic absorption spectrometry (GF-AAS). Under the optimized conditions (pH 0.6, adjusted with hydrochloric acid; flow rate, 1 ml min(-1)) chromium(VI) is retained on the column and chromium(III) is collected and determined by GF-AAS. Total chromium is directly determined by GF-AAS and chromium(VI) is calculated by difference. The relative standard deviations (10 replicate analyses) at the 20 mug l(-1) level for chromium(III) and chromium(VI) and at the 40 mug l(-1) level for total chromium were 1.4%, 3.6% and 1.8%, and the corresponding limits of detection (based on 3sigma) were 0.57 mug ml(-1), 0.61 mug ml(-1) and 0.35 mug l(-1) respectively. No large interference effects have been observed from other investigated species and the method has been successfully applied to a range of water samples.     

Flow injection spectrophotometric determination of boron in ceramic materials

A flow injection spectrophotometric method for the determination of boron in ceramic materials is described. The method is based on spectrophotometric measurement of the decrease in the pH produced by the reaction between boric acid and mannitol in the presence of an acid-base indicator. A bichannel FI (flow injection) manifold in which the sample solutions were injected into deionized water (at pH 5.4) and the stream was later merged with the reagent stream (a mannitol solution containing 1x10(-4) mol l(-1) bromocresol green at pH 5.4), was used. Transient signals were monitored at 616 nm. A theoretical model which describes the dependence between the absorbance values and boric acid concentration is presented. The model predicts a non linear dependence between the absorbance or increment in absorbance and the boric acid concentration. In contrast, the model predicts a linear dependence between the inverse of the absorbance values and the boric acid concentration. The calibration graphs (1/A vs mug ml(-1) B(2)O(3)) were linear over the range 1-30 mug ml(-1) of B(2)O(3). The relative standard deviations were 0.7 and 0.4% for 4 and 8 mug ml(-1) of B(2)O(3), respectively. The limit of detection was 0.02 mug ml(-1) of B(2)O(3) (3sigma criterium). The method was used to determine boron in nine ceramic materials with very different nominal boron compositions. The results were compared with those obtained using a potentiometric titration method as reference method. No significant differences (at 95% probability level) were found between the proposed and reference methods. The method is rapid, reliable, precise and free of interferences.     

Determination of nitrite by sequential injection analysis of electrokinetic flow analysis system

A new sequential injection analysis (SIA) method of an electrokinetic flow analysis (EKFA) system for the determination of nitrite-nitrogen is presented in this paper. The proposed system mainly consisted of an electroosmotic pump, two solenoid valves and a spectrophotometer etc. All the pump and valves were controlled by a personal computer automatically. The determination method of nitrite-nitrogen was based on the reaction among nitrite, sulfanilamide and naphthylethylenediamine to form a colored compound, which was measured at 540 nm. The linear calibration range of nitrite-nitrogen was 10-800 mug l(-1). The detection limit was 1 mug l(-1) (K=3, n=11). The analytical method can provide a throughput of 33 samples per h.     

Determination of bismuth in biological samples using on-line flow-injection microwave-assisted mineralization and precipitation/dissolution for electrothermal atomic absorption spectrometry

An on-line automated flow injection system with microwave-assisted sample digestion for the electrothermal atomic absorption spectrometric determination of bismuth in biological materials is described. After the exposure of the sample to microwave radiation, the analyte was subject to a precipitation/dissolution process. Bismuth was precipitated with the stannite ion in basic medium and collected on the walls of a knotted coil, while the other matrix components flowed downstream to waste. The precipitate was dissolved with nitric acid and a sub-sample was collected in a capillary of a sampling arm assembly, to introduce 20 mul volumes into the graphite tube by means of positive displacement with air through a time-based injector. The analytical figures of merit were first evaluated by filling the sampling arm with a standard solution of bismuth and thereafter injecting aliquots of this solution into the atomizer. The calibration graph was linear from the detection limit (8 pg) to 1.2 ng of bismuth. The sensitivity was of 26.8 mug l(-1) for 0.2 A-s and the characteristic mass (m(o)) was of 11.8 pg/0.0044 A-s. The precision of the method, evaluated by replicate analyses of solutions containing 20 and 200 pg of bismuth, were 5.5 and 3.0% (n=10), respectively. When solutions were introduced in the flow system here described, the calibration graph was linear in the range 0.04-6.0 mug l(-1), which means that a preconcentration factor of 10 was obtained for bismuth. The precision slightly deteriorated, e.g. the replicate analysis of solutions containing 1 and 10 pg of bismuth were 7.1 and 5.3% (n=10), respectively. However, the recoveries values obtained with urine and whole blood bismuth spiked samples were over 96.5% and the agreement between observed and certified values was good.     

Determination of soluble chromium in simulated PWR coolant by differential-pulse adsorptive stripping voltammetry

An analytical method has been developed for the determination of dissolved chromium at concentrations less than 2 mug/l. in PWR coolant by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode. Concentrations above 2 mug/l. can be determined by appropriate dilution of the sample. The method is based on measurement of the current associated with reduction of a chromium(III)-DTPA (diethylenetriaminepenta-acetic acid) complex adsorbed at the surface of the mercury drop. The effects of boric acid, pH, DTPA concentration, accumulation potential and time were investigated together with the oxidation state of the chromium. No interference was observed from other transition metal ions expected to be present in PWR coolant. No alternative chemical technique of similar sensitivity was available for comparison with the results obtained in solutions containing <1 mug/l. chromium. Recoveries from simulated coolant solutions were greater than 95% and the relative standard deviations for single determinations were in the range 12-25%. The statistical limit of detection at the 95% confidence level was 0.023 mug/l. This method of analysis should prove valuable in corrosion studies and is uniquely capable of following the changes in soluble chromium concentration in PWR coolant that follow operational changes in the reactor.     

Spectrophotometric detection of arsenic using flow-injection hydride generation following sorbent extraction preconcentration

An automated system with a C(18) bonded silica gel packed minicolumn is proposed for spectrophotometric detection of arsenic using flow-injection hydride generation following sorbent extraction preconcentration. Complexes formed between arsenic(III) and ammonium diethyl dithiophosphate (ADDP) are retained on a C(18) sorbent. The eluted As-DDP complexes are merged with a 1.5% (w/v) NaBH(4) and the resulting solution is thereafter injected into the hydride generator/gas-liquid separator. The arsine generated is carried out by a stream of N(2) and trapped in an alkaline iodine solution in which the analyte is determined by the arsenomolybdenum blue method. With preconcentration time of 120 s, calibration in the 5.00-50.0 mug As l(-1) range and sampling rate of about 20 samples h(-1) are achieved, corresponding to 36 mg ADDP plus 36 mg ammonium heptamolybdate plus 7 mg hydrazine sulfate plus 0.7 mg stannous chloride and about 7 ml sample consumed per determination. The detection limit is 0.06 mug l(-1) and the relative standard deviation (n=12) for a typical 17.0 mug As l(-1) sample is ca. 6%. The accuracy was checked for arsenic determination in plant materials from the NIST (1572 citrus leaves; 1573 tomato leaves) and the results were in agreement with the certified values at 95% confidence level. Good recoveries (94-104%) of spiked tap waters, sugars and synthetic mixtures of trivalent and pentavalent arsenic were also found.     

Colorimetric determination of copper in aqueous samples using a flow injection system with a pre-concentration poly(ethylenimine) column

A colorimetric flow injection-system for the determination of Cu(II) in waters based on complexation reaction with 4-(2-pyridylazo)-resorcinol, usually termed PAR, is described. Performing measurements in 0.25 mol l(-1) HNO(3) medium allowed improved selectivity of the analytical method. The lack of sensitivity deriving from the low complex absorption under acidic conditions was balanced by the insertion of an immobilised poly(ethylenimine) (PEI) column where Cu(II) pre-concentration in neutral media occurs. Using sample volumes ranging from 2 to 4 ml, sampling rates of 24 and 12 samples h(-1) within a detection limit of 25 and 13 mug l(-1), respectively, were accomplished. Accuracy of the developed methodology was assessed by comparison with atomic absorption spectrometry being the relationship [FIA] mg l(-1)=1.00 (+/-0.03)x[AAS] mg l(-1)+0.00 (+/-0.02) obtained after analysing 15 samples. Precision was also evaluated using two samples of 0.05 and 0.5 mg l(-1) copper, and a relative standard deviation (R.S.D.) better than 3% was attained for both.     

Direct determination of beryllium, copper and zinc in AlU matrices by electrothermal atomization atomic-absorption spectrometry

An atomic-absorption spectrometric method with electrothermal mode of atomization has been developed for the direct determination of Be, Cu and Zn in AlU (3:1) matrix samples without prior chemical separation of the major matrix. The studies carried out include the effect of the matrix on the analyte absorbance, optimization of sample aliquot and other experimental parameters, and analysis of a number of synthetic samples. Nanogram amounts of the analytes can be determined with a solution aliquot of 5 microlitres containing 25 micrograms of the sample with a precision of 6% or better. The analytical range obtained for these analytes is Be: 2-20 mug/l., Cu: 20-200mug/l. and Zn: 1-40mug/ml in the AlU matrix. The analysis of synthetic samples has shown good agreement with their added contents.