Direct determination of benzamides in serum by column-switching high-performance liquid chromatography.

A column-switching high-performance liquid chromatographic method with fluorescence detection was developed for the simultaneous determination of four benzamide-type anti-psychotic drugs: sulpiride, tiapride, sultopride and metoclopramide in human serum. In this method, a TSKgel Super-ODS column was used as an analytical column, and a TSKgel G 2000SW was prepared as a pretreatment column. Under the optimized analytical conditions, four benzamide-type anti-psychotic drugs were eluted within 18 min. The detection limits (S/N = 3) for sulpiride, tiapride, sultopride and metoclopramide are 1 ng/ml, 4 ng/ml, 2 ng/ml and 0.5 ng/ml, respectively. Finally, the method was applied to the determination of sulpiride in human serum samples obtained after a single oral dose of sulpiride.     

Determination of sultopride and tiapride in serum by gas chromatography using a surface ionisation detector

A sensitive and selective method has been developed for the determination of sultopride and tiapride in serum using gas chromatography with a surface ionisation detector. No interfering peaks from endogenous substances were observed. The method showed good reproducibility and accuracy, and the standard curve was linear up to 2 micrograms/ml with a correlation coefficient of 0.999. This method is applicable to pharmacokinetic studies and therapeutic drug monitoring of sultopride and tiapride.     

Chemiluminescence determination of some fluoroquinolone derivatives in pharmaceutical formulations and biological fluids using [Ru(bipy)(3)(2+)]-Ce(IV) system

A new chemiluminescence (CL) method using flow injection has been described for the rapid and sensitive determination of three fluoroquinolone derivatives, namely ofloxacin, norfloxacin and ciprofloxacin hydrochloride. The method is based on the CL reaction of the studied fluoroquinolones with tris(2,2'-bipyridyl)ruthenium(II) [Ru(bipy)(3)(2+)] and Ce(IV) in sulfuric acid medium. Under the optimum conditions, the CL intensity is proportional to the concentration of the drugs in solution over the range 0.05-7.0 mug ml(-1) for norfloxacin, 0.05-6.0 mug ml(-1) for ciprofloxacin hydrochloride and 0.003-0.7 mug ml(-1) for ofloxacin. The limits of detection (s/n=3) were 3.1x10(-8) M norfloxacin, 2.6x10(-8) M ciprofloxacin hydrochloride and 5.5x10(-9) M ofloxacin. The method was applied successfully to the determination of these compounds in dosage forms and biological fluids.     

Study on the solid phase extraction of Co(II)-QADEAB chelate with C(18) disk and its application to the determination of trace cobalt

A sensitive, selective and rapid method has been developed for the determination mug l(-1) level of cobalt based on the rapid reaction of cobalt(II) with 2-(2-quinolylazo)-5-diethylaminobenzoic acid (QADEAB) and the solid phase extraction (SPE) of the colored chelate with Waters Porapak(R) Sep-Park C(18) disk. The QADEAB can react with Co(II) in the presence of pH 3.8 acetic acid-sodium acetate buffer solution and cetyl trimethylammonium bromide (CTMAB) medium to form a violet chelate of a molar ratio 1:2 (cobalt to QADEAB). This chelate can retained on Waters Porapak(R) Sep-Park C(18) disk quantitatively when they passed the disk as aqueous solution. After the enrichment finished, the retained chelate can be eluted from disk by 2.5 ml of ethanol (contain 5% acetic acid). In the measured solution, the molar absorptivity of the chelate is 1.58x10(5) l mol(-1) cm(-1)at 635 nm, and Beer's law is obeyed in the range of 0.01-0.4 mug ml(-1). The relative standard deviation for 11 replicate sample of 0.01 mug ml(-1) level is 2.23%. The detection limit is 0.01 mug l(-1) (in original samples). This method can be applied to the determination of mug l(-1) level of cobalt in drinking water with satisfactory results.     

A simple spectrophotometric method for the determination of nylidrin hydrochloride, isoxsuprine hydrochloride and salbutamol sulphate in pharmaceutical preparations

A simple spectrophotometric method for the determination of nylidrin hydrochloride, isoxsuprine hydrochloride and salbutamol sulphate is described, based on measurement of the orangeyellow species produced when the drugs are coupled with diazotized benzocaine (p-aminoethyl benzoate) in trimethylamine medium. The method is applicable over the range 1-12 mug ml for isoxsuprine hydrochloride and nylidrin hydrochloride and 1-8 mug ml for salbutamol sulphate. The method is a modification of the Bratton-Marshall reaction and is simple, reproducible, accurate and more sensitive than those cited in the literature.     

Flow injection chemiluminescence determination of thiamine based on its enhancing effect on the luminol-hydrogen peroxide system

A new flow injection chemiluminescence (CL) method is proposed for the determination of thiamine, based upon its enhancing effect on the CL reaction of luminol with hydrogen peroxide in alkaline solution. The method allows the determination of thiamine within 0.05-8 mug ml(-1) range with a detection limit (3sigma) of 0.01 mug ml(-1). The relative standard deviation is 1.4% (n=11, 0.5 mug ml(-1) thiamine) and the sample throughput is about 90 samples h(-1). The method was successfully applied to the determination of thiamine in pharmaceutical preparations.     

Fluorimetric determination of fluoride in a flow assembly integrated on-line to an open/closed FIA system to remove interference by solid phase extraction

A simple flow injection fluorimetric method for fluoride determination is proposed. The method is based on the enhanced fluorescence of quercitin-Zr(IV) complex when fluoride ion is present in the sample. An open/closed FIA manifold with a mini-column of Dowex 50W X8 resin was used to remove the most important interference (aluminum). The two FIA assemblies were integrated on-line to automate the pretreatment of the water sample and fluoride determination. The calibration graph was linear over the range 0.1-3.0 mug ml(-1) of fluoride with a correlation coefficient of 0.999 and LOD 0.06 mug ml(-1). The relative standard deviation was 2.5% and the sample throughput was 52 h(-1) without pretreatment and 10 h(-1) with pretreatment of the sample. The method was applied to the determination of fluoride in water samples.     

A Simple and Rapid CZE Determination of Tiapride Hydrochloride and Related Impurities in Pharmaceutical Formulations

A simple, fast, inexpensive capillary zone electrophoresis method for the separation and determination of tiapride hydrochloride and its two related impurities in pharmaceutical formulations has been developed and validated. The successful separation of these compounds was achieved in less than 3 min using a fused silica capillary and photodiode array detector at 218 nm. The best conditions were obtained using a 10 mM sodium tetraborate (pH 8.0) as the running buffer. The linear responses covered the ranges from 1.0 to 100 μg mL^?1 (R = 0.9989) for tiapride hydrochloride. The detection (LOD) and quantitation limits (LOQ) for tiapride hydrochloride were 2.7 and 9.0 μg mL^?1, respectively. The intra- and inter-day relative standard deviations for migration times and peak areas were less than 0.47 and 5.7%, respectively. The method was validated for the determination of tiapride hydrochloride in commercial tablets.     

Malachite green as a reagent for detection and spectrophotometric determination of chromium(VI)

A sensitive and inexpensive method of spectrophotometric determination of chromium(VI), based on the absorbance of its complex with malachite green and acetic acid at pH 2.5 is reported. The complex shows a molar absorptivity of 8 x 10(4) l.mole(-1) cm(-1) at 560 nm, using malachite green and acetic acid as reference solution. The effect of time, temperature, pH and reagent concentration is studied and optimum operating conditions are established. Beer's law is applicable in the concentration range 2.0-22.8 mug/ml chromium(VI). The resin beads act as a catalyst and as little as 1.6 mug of chromium(VI) is detected in the resin phase as compared to 4.1 mug in the solution phase. The standard deviation in the determinations is +/-0.40 mug/ml for a 10.35 mug/ml solution.     

Capillary electrophoresis and circular dichroism study of trichosanthin and its mutants

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminoaniline (QADEAA) was synthesized. A highly sensitive, selective and rapid method for the determination of silver based on the rapid reaction of silver (I) with QADEAA has been developed. In the presence of sodium citrate-sodium hydroxide buffer solution (pH 6.5) and sodium dodecyl sulfonate (SDS) medium, QADEAA reacts with silver to form a violet complex of molar ratio 1:2 (silver to QADEAA). The molar absorptivity of the complex is 1.39x10(5) l mol(-1) cm(-1) at 580 nm. Beer's law is obeyed in the range of 0.01-0.6 mug ml(-1). The relative standard deviation for 11 replicate samples of 0.2 mug ml(-1) is 1.67%. This method can be applied to the determination of silver in water with satisfactory results.     

Solvent extraction-spectrophotometric determination of trace amounts of ammonium, barium and potassium in a mixture by dicyclohexyl-18-crown-6 and orange II

A simple and sensitive extraction-spectrophotometric method for the determination of ammonium, barium and potassium in a mixture solution is reported. The DC18C6-ammonium-Orange II (DC18C6-NH(4)-OR II), DC18C6-Barium-Orange II (DC18C6-Ba-(OR II)(2)) and DC18C6-Potassium-Orange II (DC18C6-K-OR II) ternary complexes are quantitatively extracted into dichloromethane and their absorbances are measured at 483 nm. Linear calibration graphs were obtained over the concentration ranges of 0.05-3.00, 0.05-2.00 and 0.05-6.00 mug ml(-1) for ammonium, barium and potassium, respectively. The relative standard deviations for 1.0 mug ml(-1) of ammonium, barium and potassium are, respectively, 1.1, 1.6 and 2.50%. The limit of detection, LOD, for these three ions is reported to be 0.02, 0.01 and 0.02 mug ml(-1), respectively. The interfering effect of a large number of diverse ions on the determination of these three ions was studied. The method was applied to the Karon river raw water contaminated with industrial and house sewages. The results showed high potential of the recommended method for the determination of NH(4)(+), Ba(2+) and K(+) in water samples.     

Long-wavelength stopped-flow fluorimetric determination of lysozyme

The use of Cresyl Violet and sodium dodecyl sulphate for the kinetic fluorimetric determination of lysozyme from dynamic fluorescence measurements at a long wavelength in the range near 600 nm was explored. The high initial rate of this system allows analytical measurements to be made within ca. 2 s after the reactants are mixed, by using the stopped-flow mixing technique, which makes the method applicable to automatic routine analysis. The calibration graph is linear over the range 0.5-40 mug ml(-1) lysozyme hydrochloride and the detection limit of 0.19 mug ml(-1). The precision is less than 2% (relative standard deviation). The results obtained by applying the proposed method to the analysis of pharmaceutical samples with no pretreatment shown how readily it can be adapted for routine analyses. Analytical recoveries ranged between 94.0 and 104.0%.     

Simultaneous determination of naproxen, salicylic acid and acetylsalicylic acid by spectrofluorimetry using partial least-squares (PLS) multivariate calibration

Determination of naproxen, salicylic acid and acetylsalicylic acid has been carried out in mixtures of up to three components by recording emission fluorescence spectra between 300 and 520 nm with an excitation wavelength of 290 nm. The excitation-emission spectra of these compounds are strongly overlapped, which does not permit their direct determination without previous separation by conventional methodologies. Here, a method is proposed for the determination of these chemicals by the use of a full-spectrum multivariate calibration method, partial least-squares (PLS). The experimental calibration matrix was designed with 18 samples. The concentrations were varied between 0.1 and 1.0 mug ml(-1) for naproxen, 0.5 and 5.0 mug ml(-1) for salicylic acid and from 2.0 to 12.0 mug ml(-1) for acetylsalicylic acid. The cross-validation method was used to select the number of factors. To check the accuracy of the proposed method, the optimized model, obtained using PLS-1, was applied to the determination of these compounds in pharmaceuticals and human serum samples previously spiked with different amounts of each chemical.     

Permanganate-based chemiluminescence analysis of cefadroxil monohydrate in pharmaceutical samples and biological fluids using flow injection

A chemiluminescent method using flow injection is described for the determination of cefadroxil monohydrate. The method is based on the chemiluminescence reaction of cefadroxil with potassium permanganate in sulphuric acid, sensitized by quinine. The proposed procedure allows the determination of cefadroxil over the concentration range 0.1-30 mug ml(-1) with a detection limit of 0.05 mug ml(-1) and a sample measurement frequency of 150 samples h(-1). The method was successfully applied to the determination of cefadroxil in pharmaceutical preparations and biological fluids.     

巯基乙酸修饰金电极电化学发光行为的研究及其对盐酸硫必利的测定

在裸金电极上制备了巯基乙酸自组装膜修饰电极(MA/SAMs-Au/CME)。基于盐酸硫必利对联吡啶钌在该电极上的电化学及其发光行为的强烈增敏作用,建立起一种直接测定盐酸硫必利电致化学发光新方法。在最佳实验条件下,盐酸硫必利在1.0×10-4～1.0×10-7mol/L与相对发光强度呈线性关系,其线性回归方程I(强度)=27.169×106c+140.26,r2=0.9959,检出限(S/N=3)为5.11×10-9mol/L。连续测定1.0×10-5mol/L盐酸硫必利10次,发光强度的RSD值为1.8%。对样品进行回收率试验,回收率在94.1%～104.9%之间,RSD为4.5%(n=5)。     

Simultaneous determination of manganese and zinc in mixtures using first- and second-derivative spectrophotometry

A new direct spectrophotometric determination of manganese with 5,8-dihydroxy-1,4-naphthoquinone (naphthazarin,NAZA) is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of 1:2 (M:L) complex are 695 nm, 1.88x10(4) l mol(-1) cm(-1) and 2.92 ng cm(-2), respectively. A linear calibration graph is obtained up to a concentration of 7.2 mug ml(-1) of manganese. The optimum range for determination (Ringbom) is between 0.20 and 6.8 mug ml(-1). A rapid method for simultaneous determination of manganese and zinc in their mixture using derivative spectra is described. The range 0.28-5.6 mug ml(-1) manganese could be determined in the presence of 0.33-6.8 mug ml(-1) zinc and vice versa. The developed method was applied to the simultaneous spectrophotometric determination of manganese and zinc in some synthetic mixtures and was found to give satisfactory results.     

Spectrophotometric determination of micro-amounts of vanadium with 5,7-di-iodo-8-hydroxyquinoline

A precise spectrophotometric method for the determination of 2.5-25 mug of vanadium in volumes of up to 500 ml of water was developed. The method is based on the simultaneous concentration (100-1000 fold) and complexation of vanadium(V) with di-iodo-oxine in a water-immiscible phase. Interference from iron is eliminated by masking with phosphoric acid. The standard deviation evaluated was +/-0.04 mug for solutions containing 5 mug vanadium.     

A simple simultaneous flow injection method based on phosphomolybdenum chemistry for nitrate and nitrite determinations in water and fish samples

A direct spectrophotometric flow injection method for the simultaneous determination of nitrite and nitrate has been developed. The method is based on the oxidation of a phosphomolybdenum blue complex by the addition of nitrite and the decrease in absorbance of the blue complex is monitored at 820 nm. The injected sample is split into two segments. One of the streams was directly reacted with the above reagent and detected as nitrite. The other stream was passed through a copperised cadmium reductor column where reduction of nitrate to nitrite occurs, and the sample was then mixed with the reagent and passed through the cell of the spectrophotometer to be detected as nitrite plus nitrate. The conditions for the flow injection manifold parameters were optimised by experimental design and the concentration of nitrite and nitrate was determined in the linear range from 0.05 to 1.15 mug ml(-1) nitrite and 0.06 to 1.6 mug ml(-1) nitrate with a detection limit of 0.01 mug ml(-1) for nitrite and 0.025 mug ml(-1) for nitrate. The method is suitable for the simultaneous determination of nitrite and nitrate in fish and water samples with a sampling rate of 25+/-2 sample per hour.     

A spectrophotometric method for the determination of copper ions and its application to the co-precipitation of copper in the crystallization of sodium

The molar absorptivity of the cyanide complexes [Cu(CN)(3)](2-) and [Cu(CN)(4)](3-), at their isosbestic wavelength (235 nm) is 1.13 x 10(3) l.mole(-1)mm.(-1) and can be used for the quantitative determination of micro-amounts of copper in the ppm range. The determination of 1-10 mug of Cu(2+) per g of NaCl, or 0.25-2.5 mug ml , is described in detail. The co-precipitation of copper with NaCl crystallizing from aqueous solutions has been studied by this method.     

Flow injection spectrophotometric determination of trace amounts of selenium

A simple, rapid and sensitive flow injection spectrophotometric method for determination of selenium (0.005-1.5 mug ml(-1)) is described. The method is based on the catalytic effect of Se(IV) on the reduction reaction of thionine (TN) with sulphide ion, monitored spectrophotometrically at 598 nm. The detection limit is 5 ng ml(-1) the relative standard deviation for eight replicate measurements is 1.1% for 1 mug ml(-1) of selenium. The sampling rate is 25-30 samples h(-1). The procedure was applied successfully to the determination of selenium in real samples.