Selective extraction of triazine herbicides from food samples based on a combination of a liquid membrane and molecularly imprinted polymers

A selective extraction technique based on the combination of liquid membrane (microporous membrane liquid–liquid extraction) and molecularly imprinted polymers (MIP) was applied to triazines herbicides in food samples. Simazine, atrazine and propazine were extracted from aqueous food samples through the hydrophobic porous membrane that was impregnated with toluene, which also formed part of the acceptor phase. In the acceptor phase, the compounds were re-extracted onto MIP particles. The extraction technique was optimised for the amount of molecularly imprinted polymers particles in the organic acceptor phase, extraction time, and type of organic acceptor solvent and desorption solvent. An extraction time of 90 min and 50 mg of MIP were found to be optimum parameters. Toluene as the acceptor phase was found to give higher triazines binding onto MIP particles compared to hexane and combinations of diethyl ether and hexane. 90% methanol in water was found to be the best desorption solvent compared to acetonitrile, methanol and water. The selectivity of the technique was demonstrated by extracting spiked lettuce and apple extracts where clean chromatograms were obtained compared to liquid membrane extraction alone or to the microporous membrane liquid–liquid extraction – non-imprinted polymer combination. The MIP showed a certain degree of group specificity and the extraction efficiency in lettuce extract was 79% (0.72) for simazine, 98% (1.55) for atrazine and 86% (3.08) for propazine.     

Potential of combining of liquid membranes and molecularly imprinted polymers in extraction of 17β‐estradiol from aqueous samples

The potential of combination of liquid membranes (microporous membrane liquid–liquid extraction) and molecularly imprinted polymers (MIPs) was performed using 17β‐estradiol (E2) as model compound. The model compound was extracted from aqueous sample through a hydrophobic porous membrane that was impregnated with hexane/ethyl acetate (3:2), which also formed part of the acceptor phase. In the acceptor phase, the compound was bound onto MIP particles that were also part of the organic phase. The potential of such combination was optimised for the type and amount of MIP particles in the organic acceptor phase, the extraction time, and the type of organic acceptor solvent. Ultrasound assisted binding of E2 onto MIP particles was also investigated. MIPs prepared by precipitation polymerization were found to be superior to those prepared by bulk polymerization. Increase in the extraction time and the amount of MIP particles in the acceptor phase led to more E2 binding onto the MIP particles. Hexane/ethyl acetate (3:2) as an organic acceptor was found to give higher E2 binding onto MIP particles compared to toluene, diethyl ether, and hexane. Ultrasound was furthermore found to increase the binding of E2 onto MIP particles. The selectivity of the technique was demonstrated by extracting wastewater and where clean chromatograms were obtained compared to liquid membrane extractions (SLMs) alone.     

Development and optimisation of a novel three‐way extraction technique based on a combination of Soxhlet extraction,membrane assisted solvent extraction and a molecularly imprinted polymer using sludge polycyclic aromatic hydrocarbons as model compounds

A novel technique that integrates extraction and clean‐up into a single step format is reported as part of the search for new sample preparation techniques in the analysis of persistent organic pollutants from complex samples. This was achieved by combining the extraction efficiency of the Soxhlet extractor, the selectivity of a size exclusion membrane and the specificity of a molecularly imprinted polymer for the extraction of polycyclic aromatic hydrocarbons from wastewater sludge followed by quantitation using gas chromatography with time‐of‐flight mass spectrometry. The approach is described as the Soxhlet extraction membrane‐assisted solvent extraction molecularly imprinted polymer technique. This technique was optimised for various parameters such as extraction solvent, reflux time and membrane acceptor phase. The applicability of the developed technique was optimised using a wastewater sludge certified reference material and then tested on real wastewater sludge samples. The method detection limits ranged from 0.14 to 12.86 ng/g with relative standard deviation values for the extraction of the 16 US‐EPA priority polycyclic aromatic hydrocarbons from wastewater sludge samples ranging from 0.78 to 18%. The extraction process was therefore reproducible and showed remarkable selectivity. The developed technique is a promising prospect that can be applied in the analysis of organic pollutants from complex solid samples.     

Effect of solvents on the selectivity of terbutylazine imprinted polymer sorbents used in solid-phase extraction

A solid-phase extraction sample preparation method using a molecularly imprinted polymer (MIP) selective for the triazine type pesticide terbutylazine has been developed. The method involves preconcentration from large volumes of water samples on a C18 disk coupled to selective clean-up on the MIP. The method has been optimised by studying the recovery and retention of terbutylazine and some other structurally related triazine derivates as a function of the selective washing solvent used. The effect of the water content of the selective washing solvent was also investigated on the recovery of the MIP. River water samples were analysed with the coupled technique, and efficient clean-up of the samples was observed.     

Liquid–liquid–solid microextraction based on membrane-protected molecularly imprinted polymer fiber for trace analysis of triazines in complex aqueous samples

A novel liquid–liquid–solid microextraction (LLSME) technique based on porous membrane-protected molecularly imprinted polymer (MIP)-coated silica fiber has been developed. In this technique, a MIP-coated silica fiber was protected with a length of porous polypropylene hollow fiber membrane which was filled with water-immiscible organic phase. Subsequently the whole device was immersed into aqueous sample for extraction. The LLSME technique was a three-phase microextraction approach. The target analytes were firstly extracted from the aqueous sample through a few microliters of organic phase residing in the pores and lumen of the membrane, and were then finally extracted onto the MIP fiber. A terbutylazine MIP-coated silica fiber was adopted as an example to demonstrate the feasibility of the novel LLSME method. The extraction parameters such as the organic solvent, extraction and desorption time were investigated. Comparison of the LLSME technique was made with molecularly imprinted polymer based solid-phase microextraction (MIP-SPME) and hollow fiber membrane-based liquid-phase microextraction (HF-LPME), respectively. The LLSME, integrating the advantages of high selectivity of MIP-SPME and enrichment and sample cleanup capability of the HF-LPME into a single device, is a promising sample preparation method for complex samples. Moreover, the new technique overcomes the problem of disturbance from water when the MIP-SPME fiber was exposed directly to aqueous samples. Applications to analysis of triazine herbicides in sludge water, watermelon, milk and urine samples were evaluated to access the real sample application of the LLSME method by coupling with high-performance liquid chromatography (HPLC). Low limits of detection (0.006–0.02 μg L⁻¹), satisfactory recoveries and good repeatability for real sample (RSD 1.2–9.6%, n = 5) were obtained. The method was demonstrated to be a fast, selective and sensitive pretreatment method for trace analysis of triazines in complex aqueous samples.     

Recent advances and applications of molecularly imprinted polymers in solid‐phase extraction for real sample analysis

Sample pretreatment is essential for the analysis of complicated real samples due to their complex matrices and low analyte concentrations. Among all sample pretreatment methods, solid‐phase extraction is arguably the most frequently used one. However, the majority of available solid‐phase extraction adsorbents suffer from limited selectivity. Molecularly imprinted polymers are a type of tailor‐made artificial antibodies and receptors with specific recognition sites for target molecules. Using molecularly imprinted polymers instead of conventional adsorbents can greatly improve the selectivity of solid‐phase extraction, and therefore molecularly imprinted polymer‐based solid‐phase extraction has been widely applied to separation, clean up and/or preconcentration of target analytes in various kinds of real samples. In this article, after a brief introduction, the recent developments and applications of molecularly imprinted polymer‐based solid‐phase extraction for determination of different analytes in complicated real samples during the 2015‐2020 are reviewed systematically, including the solid‐phase extraction modes, molecularly imprinted adsorbent types and their preparations, and the practical applications of solid‐phase extraction to various real samples (environmental, food, biological, and pharmaceutical samples). Finally, the challenges and opportunities of using molecularly imprinted polymer‐based solid‐phase extraction for real sample analysis are discussed.     

Molecularly imprinted polymer with high-fidelity binding sites for the selective extraction of barbiturates from human urine

In this paper we describe the synthesis of a molecularly imprinted polymer (MIP) by precipitation polymerisation, with barbital as the template molecule, and the application of the barbital MIP as a molecularly selective sorbent in the solid-phase extraction (SPE) of barbiturates from human urine samples. The MIP was synthesised by precipitation polymerisation using 2,6-bis-acrylamidopyridine as the functional monomer and DVB-80 as the cross-linking agent. The spherical MIP particles produced were 4.2 ± 0.4 μm in diameter; a non-imprinted control polymer (NIP) in bead form was 4.8 ± 0.4 μm (mean±standard deviation) in diameter. The particles were packed into a solid-phase extraction cartridge and employed as a novel sorbent in a molecularly imprinted solid-phase extraction (MISPE) protocol. The MIP showed high selectivity for the template molecule, barbital, a feature which can be ascribed to the high-fidelity binding sites present in the MIP which arose from the use of 2,6-bis-acrylamidopyridine as the functional monomer. However, the MIP also displayed useful cross-selectivity for other barbiturates besides barbital. For real samples, the MIP was applied for the extraction of four barbiturates from human urine. However, due to the high urea concentration in this sample which interfere the proper interaction of barbiturates onto the MIP, a tandem system using a commercially available sorbent was developed.     

Selective solid phase extraction of propranolol on multiwell membrane filter plates modified with molecularly imprinted polymer

Molecularly imprinted polymers (MIPs) were synthesized in 24-well glass fiber membrane filter plates to obtain a novel type of solid phase extraction device for the cleanup of propranolol. Sample processing parameters like residence time during sample loading, sample volume, pH, sample solvent, type and amount of washing and elution solvents were investigated and optimized. Important differences from the traditional molecularly imprinted solid phase extraction (MISPE) cartridges have been identified. The MIP modified composite membrane suits well for the sample preparation of low volume biological samples. A protocol has been elaborated for the quantitation of propranolol from urine and plasma samples in the clinically relevant concentration ranges. Preliminary validation results indicate that the composite MIP membrane filter plates offer a viable alternative to existing MISPE cartridges and at the same time have advantages like much easier and faster synthesis method and high-throughput analysis.     

分子印迹固相萃取技术在天然产物有效成分分离分析中的应用进展

天然产物体系复杂,尤其是一些活性成分含量较低,采用一般的方法对其进行分离富集难度较大。分子印迹聚合物具有良好的亲和性和专一的选择性,将分子印迹固相萃取技术应用于天然药物资源样品前处理过程,能够选择性地分离富集复杂基质中的目标成分。本文对近几年分子印迹固相萃取技术在天然产物有效成分分离分析中的应用进行了总结,分析物包括黄酮类、多元酚类、生物碱类、有机酸类、苯丙素类、萜类以及其他一些类型的生物活性成分。     

Molecularly imprinted solid phase extraction for rapid screening of metformin

A molecularly imprinted solid phase extraction (MISPE) method has been developed for the rapid screening of metformin. Newly synthesized molecularly imprinted polymer (MIP) particles were slurry-packed into a micro-column for selective solid phase extraction (SPE) of metformin. With CH₃CN flowing at 0.5 ml/min, a total binding capacity of 1600 ng metformin was determined for the 20 mg of MIP particles. A broad range of MISPE conditions was evaluated with respect to sample solvent, pH, and buffer compositions. A 95±2% binding could be achieved from one 20-μl injection of sample solution in acetonitrile plus phosphate buffer, up to 1200 ng of metformin. However, the micro-column interacted indiscriminately with phenformin, a structural analogue, to attain 49±2% binding. Separation of phenformin from metformin was ultimately achieved, using differential pulsed elution (DPE) with 1 M trifluoromethacrylic acid in acetonitrile. Final pulsed elution (FPE) using 3% trifluoroacetic acid in methanol was good for the quantitative elution of metformin. The MISPE–DPE–FPE method, with UV detection at 240 nm, afforded a detection limit of 0.8 μg/ml (or 16 ng) for metformin. Each MISPE–DPE–FPE analysis required less than 5 min to complete.     

Molecularly imprinted covalent organic polymers for the selective extraction of benzoxazole fluorescent whitening agents from food samples

Molecularly imprinted covalent organic polymers were constructed by an imine‐linking reaction between 1,3,5‐triformylphloroglucinol and 2,6‐diaminopyridine and used for the selective solid‐phase extraction of benzoxazole fluorescent whitening agents from food samples. Binding experiments showed that imprinting sites on molecularly imprinted polymers had higher selectivity for targets compared with those of the corresponding non‐imprinted polymers. Parameters affecting the solid‐phase extraction procedure were examined. Under optimal conditions, actual samples were treated and the eluent was analyzed with high‐performance liquid chromatography with diode‐array detection. The results showed that the established method has a wide linearity, satisfactory detection limits and quantification limits, and acceptable recoveries. Thus, this developed method possesses the practical potential for the selective determination of benzoxazole fluorescent whitening agents in complex food samples.     

Evaluation of a molecularly imprinted polymer for the isolation/enrichment of β-estradiol

The selective preconcentration of estradiol was explored using the recognition ability of a molecularly imprinted polymer (MIP) in the solid phase extraction (SPE) format. Polymeric particles were imprinted with 17β-estradiol using methacrylic acid as functional monomer and divinylbenzene as crosslinker. Binding studies of these polymeric particles towards 17β-estradiol showed selectivity over non-imprinted polymers, using acetonitrile as solvent. The imprinted polymer showed a recovery of 88% for β-estradiol in deionized water and 81% in surface water. The selectivity of the MIP over the non-imprinted polymer was relatively low, only 10% higher recovery. The results indicate that the MIP imprinted with 17β-estradiol does not appear to provide a viable approach to be used in a sample clean-up or enrichment step for the determination of estradiol in aqueous systems.     

Selective trace analysis of chloroacetamide herbicides in food samples using dummy molecularly imprinted solid phase extraction based on chemometrics and quantum chemistry

A methodology based on chemometrics and quantum chemistry was proposed to design and synthesize dummy molecularly imprinted polymers (DMIPs) capable of extracting chloroacetamide herbicides from food samples. Molecular modeling approach in conjunction with clustering analysis was used to predict the most suitable dummy template. Metolachlor deschloro was selected as the template to synthesize DMIPs, which were used as the solid phase extraction (SPE) materials. The selective adsorption of DMIPs was evaluated by high performance liquid chromatography (HPLC). The retention property of six chloroacetamide herbicides on DMIPs was also predicted using clustering analysis. The optimum loading, washing and eluting conditions for dummy molecularly imprinted solid phase extraction (DMISPE) were established to obtain high selectivity and sensitivity. Water, dichloromethane and methanol were chosen as loading, washing and elution solvent, respectively. Under optimized DMISPE conditions, recoveries of analytes were in the range of 83.4–106.7% with satisfactory precision (RSD% lower than 13%). Compared with other commercial SPE columns, DMISPE exhibited selective binding properties for chloroacetamide herbicides and the matrix effect was significantly decreased.     

Determination of tetracyclines in food samples by molecularly imprinted monolithic column coupling with high performance liquid chromatography

A novel solid phase extraction (SPE) method for determination of tetracyclines (TCs) in milk and honey samples by molecularly imprinted monolithic column was developed. Using tetracycline (TC) as the template, methacrylic acid (MAA) as the functional monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linker, methanol as the solvent, cyclohexanol and dodecanol as the mixed porogenic solvents, a TC imprinted monolithic column was prepared by in situ molecular imprinting technique for the first time, and the optimal synthesis conditions and the selectivity of TC imprinted monolithic column were investigated. The interfering substances in food samples and TCs can be separated successfully on imprinted column. Molecularly imprinted solid phase extraction (MISPE) coupling with C18 column was used to determinate the TCs in milk and honey. The recoveries of this method for six tetracyclines antibiotics such as tetracycline (TC), oxytetracycline (OTC), minocycline (MINO), chlortetracycline (CTC), metacycline (MTC) and doxycycline (DTC) were investigated, and high recoveries of 73.3-90.6% from milk samples and 62.6-82.3% from honey samples were obtained. A method for determination of TCs at low concentration level in milk and honey samples was successfully developed by using the monolithic column as the precolumn for solid phase extraction of six TCs compounds.     

Synthesis of surface molecularly imprinted polymer and the selective solid phase extraction of imidazole from its structural analogs

A surface molecularly imprinted polymer (MIP) was synthesized by using imidazole as the template and modified silica particles as the support material. The static adsorption, solid phase extraction (SPE) and high-performance liquid chromatography (HPLC) experiments were performed to investigate the adsorption properties and selective recognition characteristics of the polymer for imidazole and its structural analogs. It was shown that the maximum binding capacities of imidazole on the MIP and the non-imprinted polymer (NIP) were 312 and 169 μmol g⁻¹, respectively. The adsorption was fast and the adsorption equilibrium was achieved in 30 min. The binding process could be described by pseudo-second order kinetics. Compared with the corresponding non-imprinted polymer, the molecularly imprinted polymer exhibited much higher adsorption performance and selectivity for imidazole. The selective separation of imidazole from a mixture of 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]) and 2,4-dichlorophenol could be achieved on the MIP-SPE column. The recoveries of imidazole and [C₆mim][Br] were 97.6-102.7% and 12.2-17.3%, respectively, but 2,4-dichlorophenol could not be retained on the column. The surface molecularly imprinted polymer presented here may find useful application as a solid phase absorbent to separate trace imidazole in environmental water samples. This may also form the basis for our research program on the preparation and application of alkyl-imidazolium imprinted polymers.     

分子印迹技术在样品前处理中的应用

分子印迹聚合物具有选择性高、稳定性好及制备简单的特点,可用于生物、医药、环境样品等复杂基体中痕量分析物的高选择性分离与富集,因此在样品前处理中的应用特别引人关注.本文介绍了分子印迹技术的基本原理,综述了分子印迹技术在样品前处理中应用的研究进展.     

Determination of melamine in aquaculture feed samples based on molecularly imprinted solid‐phase extraction

This research highlights the application of highly efficient molecularly imprinted solid‐phase extraction for the preconcentration and analysis of melamine in aquaculture feed samples. Melamine‐imprinted polymers were synthesized employing methacrylic acid and ethylene glycol dimethacrylate as functional monomer and cross‐linker, respectively. The characteristics of obtained polymers were evaluated by scanning electron microscopy, Fourier transform infrared spectroscopy and binding experiments. The imprinted polymers showed an excellent adsorption ability for melamine and were applied as special solid‐phase extraction sorbents for the selective cleanup of melamine. An off‐line molecularly imprinted solid‐phase extraction procedure was developed for the separation and enrichment of melamine from aquaculture feed samples prior to high‐performance liquid chromatography analysis. Optimum molecularly imprinted solid‐phase extraction conditions led to recoveries of the target in spiked feed samples in the range 84.6–96.6% and the relative standard deviation less than 3.38% (n = 3). The aquaculture feed sample was determined, and there was no melamine found. The results showed that the molecularly imprinted solid‐phase extraction protocols permitted the sensitive, uncomplicated and inexpensive separation and pre‐treatment of melamine in aquaculture feed samples.     

Investigation of ractopamine‐imprinted polymer for dispersive solid‐phase extraction of trace β‐agonists in pig tissues

Ractopamine, as an alternative β‐agonist to clenbuterol, is more and more used as leanness‐enhancing agent in the swine industry. This work presents a new molecularly imprinted polymer (MIP) using ractopamine as template for dispersive solid‐phase extraction of trace ractopamine and the structural related β‐agonists in animal tissues. The binding properties and selectivity of MIP were investigated. High selectivity in polar environment was found, since the extraction capacity of ractopamine with the MIP was 4.5‐fold as much as that with the non‐imprinted polymer in acetonitrile. Cross‐selectivity investigation indicates that the MIP preferentially binds the template and then the structural analogues according to their molecular similarity. Thermodynamic and kinetic investigation was performed to interpret the specific adsorption and molecular recognition of the MIP for ractopamine. Standard free energy, standard enthalpy, and standard entropy were determined. Related information suggested that adsorption of ractopamine onto MIP was an exothermic, spontaneous process. The MIP can be applied as dispersive solid‐phase extraction material for enrichment of ractopamine, isoxsuprine, fenoterol and clenbuterol in complex samples before HPLC analysis. The method revealed detection limits of 0.20–0.90 μg/L, recoveries of 83.8–115.2 and 85.2–110.2% for the spiked pig muscle and pig liver, respectively, with the RSD from 2.5 to 8.8%.     

Comparison of four extraction methods for analysis of volatile hop‐derived aroma compounds in beer

The volatile organic compound profile in beer is derived from hops, malt, yeast, and interactions between the ingredients, making it very diverse and complex. Due to the range and diversity of the volatile organic compounds present, the choice of the extraction method is extremely important for optimal sensitivity and selectivity. This study compared four extraction methods for hop‐derived compounds in beer late hopped with Nelson Sauvin. Extraction capacity and variation were compared for headspace solid‐phase micro extraction, stir bar sorptive extraction, headspace sorptive extraction, and solvent‐assisted flavor evaporation. Generally, stir bar sorptive extraction was better suited for acids, headspace sorptive extraction for esters and aldehydes, while headspace solid‐phase microextraction was less sensitive overall, extracting 40% fewer compounds. Solvent‐assisted flavor evaporation with dichloromethane was not suitable for the extraction of hop‐derived volatile organic compounds in beer, as the profile was strongly skewed towards alcohols and acids. Overall, headspace sorptive extraction is found to be best suited, closely followed by stir bar sorptive extraction.     

Evaluation of a novel microextraction technique for aqueous samples: porous membrane envelope filled with multiwalled carbon nanotubes coated with molecularly imprinted polymer

A novel microextraction technique based on membrane-protected multiwalled carbon nanotubes coated with molecularly imprinted polymer (MWCNTs-MIP) was developed. In this technique, MWCNTs-MIP were packed inside a polypropylene membrane envelope, which was then clamped onto a paper clip. For extraction, the packed membrane envelope was first impregnated with toluene and then placed in sample solutions. Target analytes in the solutions were first extracted into toluene in the membrane envelope, and were then extracted specifically onto the MWCNTs-MIP. After the extraction, target analytes were desorbed in methanol for liquid chromatography analysis. MWCNTs-MIP of prometryn were used as a model to demonstrate the feasibility of this novel microextraction technique. Factors affecting the extraction including organic solvent, stirring rate, extraction time, salt concentration, and pH were investigated. Under the optimized conditions, the limits of detection (a signal-to-noise ratio of 3) for the selected triazine herbicides were 0.08-0.38 μg/L. The prepared membrane envelope could be used at least 50 times. The developed method was used for the analysis of the triazines spiked in river water, wastewater, and liquid milk, with recoveries ranging from 79.3-97.4, 58.9-110.3 and 76.2-104.9%, respectively.