纳米晶钛酸钡的介电性能

采用硬脂酸凝胶法制备了纳米晶BaTiO3,用差热热重分析、红外光谱分析、X射线衍射分析等手段对产物的形成过程、晶型、粒径进行了分析.通过对材料介电性能的研究发现,纳米材料的静态介电常数远大于常规材料的介电常数,随着粒径的减小,纳米材料的介电常数先增大而后有所降低.随着环境湿度的升高,纳米晶材料的介电常数逐渐增大,在高湿度条件下,其介电常数与湿度成线性关系.     

溶胶-凝胶模板法制备钛酸钡纳米管

采用氢氧化钡和钛酸四丁酯为前驱体, 溶胶-凝胶结合模板法制备了钛酸钡纳米管, 通过SEM, TEM, XPS和XRD等表征分析, 钛酸钡纳米管直径100 nm, 钛酸钡为立方相结构, 晶胞参数a＝3.995 Å.     

溶胶-凝胶法制备掺锰钛酸钡纳米粉体及其陶瓷

The Mn-doped barium titanate nanosized powders and ceramics were prepared via the sol-gel process. The powders and ceramics were characterized by XRD， SEM and TEM. The dielectric properties of the ceramics were also measured. The influences of calcination temperature and Mn concentration on the microstructure， dielectric properties and phase composition of BaTiO₃ nano-powders and ceramics were discussed. The results indicated that the BaTiO₃-based powders doped with 1.0mol% Mn were mainly in cubic BaTiO₃ phase， but the tetragonal phase became more evident when the calcination temperature increased. After sintering， Mn-doped ceramics were mainly composed of cubic BaTiO₃. Specially， a new phase of hexagonal crystal BaTiO₃ and BaMnO₃ existed in the ceramics doped with 5.0mol% Mn and the ceramic grains were in ‘clintheriform’. The structure of ‘clintheriform’ led to the poor densification of ceramics， reducing the dielectric constant obviously. The dielectric constants of BaTiO₃ ceramics first increased and then decreased as the Mn concentration increased. The room temperature dielectric constant was 2 290 and the lowest dielectric loss was 0.004 when the Mn concentration was 0.5mol%.     

钐掺杂对钛酸钡锶陶瓷结构和介电性能的影响

采用溶胶-凝胶法制备了系列Sm掺杂的Ba(0.8-3x/2)SmxSr0.2TiO3(x=0,0.001,0.003,0.006,0.008 and 0.010)粉体及陶瓷。利用X射线粉末衍射、扫描电子显微镜和精密阻抗分析表征了样品的结构和性质。X射线衍射结果表明Ba(0.8-3x/2)SmxSr0.2TiO3粉体在800℃预烧2 h后为单一的钙钛矿结构;通过对陶瓷微观形貌研究发现,Sm掺杂可以明显地抑制陶瓷晶粒生长,随着Sm掺杂量的增加,晶粒尺寸由40μm减小到2μm;居里温度随着Sm掺杂量的增加而线性降低,移动速率为10℃/mol%,室温下介电常数呈现先增加后减小的趋势,并在x=0.006时达到最大值7800。     

纳米钛酸钡及其烧结物的制备

溶胶 凝胶技术已为制备各种金属氧化物纳米材料的较普遍方法[1],其优点是产物具有超细颗粒尺寸 ,高纯度和化学均匀性 .溶胶 凝胶法制备纳米钛酸钡时一般将钛的有机醇盐与钡盐反应生成溶胶 ,然后形成凝胶 ,再进行热处理制得纳米钛酸钡[2 ,3].本文以钛酸丁酯和氢氧化钡为原料 ,采用溶胶 凝胶工艺制备出纳米钛酸钡晶体粉末 .用ＴＧ ＤＴＡ和ＦＴＩＲ技术考查了纳米晶钛酸钡凝胶先体热分解反应过程 ,用ＳＥＭ和ＸＲＤ对粉体形貌和晶型进行分析 ;并用上述粉体制成了微观组织结构仍保持纳米尺寸的陶瓷材料 .粉体制备 :称 15 7ｇ氢氧化钡 (Ｂａ(…     

微波照射制备钛酸钡纳米晶

Cubic barium titanate nanocrystals were prepared by Ti(OC₄H₉)₄ and C₂H₅OH mixture with BaCl₂ aqueous solution under normal atmosphere microwave irradiation. Experiment results showed that when n_Ba / n_Ti=1.1, φ_EtOH=25%,highly dispersed barium titanate with particle size about 30 nm were completely formed by microwave irradiation only for 0.5 h. Microwave irradiation time had almost no effects on particle size and morphology of the product. Particle sizes were decreased with the increased EtOH amount, when φ_EtOH=50%, microwave irradiation 2 h, barium titanate nanocrystals with average size only about 22 nm were obtained.     

单分散钛酸钡纳米晶的制备

采用溶剂热法制备出表面包裹油酸的单分散立方相钛酸钡纳米晶, 晶粒平均尺寸为6.0 nm, 采用TEM和XRD对其微结构进行了表征; 研究了醇的链长度、油酸用量和热处理温度等对钛酸钡的相组成和形貌的影响规律. 研究结果表明, 产物粒径较小, 粒度分布较窄, 单分散性较好, 其表面为非极性, 可溶于非极性试剂; 由于纳米晶表面由亲油性的长链烷基所覆盖, 与周围的水性环境不相容, 产生一定的斥力; 在重力和该斥力的共同作用下, 纳米晶可以有效地从液相环境中分离出来.     

三种不同的纳米钴铁氧体热分解过程、结构和磁性的对比研究

为了改善钴铁氧体材料的性能,本研究采用溶胶-凝胶法,制备出三种具有尖晶石结构的纳米钴铁氧体.经前躯体热分解反应过程分析,产品X射线衍射分析,磁性分析测定,结果表明三种钴铁氧体的各个热分解阶段分别是由若干个反应复合而成,各个热分解阶段的活化能各不相同;产品为平均粒径50～60nm左右的尖晶石相:矫顽力及比饱和磁化强度分别呈不同的变化趋势,因为LaCl3.nH2O代替部分CoCl26H20后,稀土离子进入尖晶石晶格导致磁电子的自旋倾斜,材料矫顽力下降,但LaCl3.nH2O代替部分FeCl2.4H2O后这是由于稀土离子4f层电子受到外层电子的屏蔽保护,可通过自旋-轨道偶合对磁各向异性产生贡献,使矫顽力有明显的提高.     

溶胶-凝胶法制备钛酸钡超细粉体的研究

钛酸钡是一种非常重要的铁电材料 ,其合成方法主要分为固相反应法和液相反应法。传统的固相反应法是以ＴｉＯ2 和ＢａＣＯ3 经高温反应制取钛酸钡粉体 ,该法产品杂质含量高 ,颗粒粗 ,均匀性差 ,粉体烧结温度高。与高温固相反应相比 ,液相法合成的钛酸钡粉体具有化学纯度高 ,颗粒细小 ,粒度分布均匀等优点。特别是以醇盐为原料 ,采用溶胶 凝胶法制备的钛酸钡粉体 ,其性能非常优异 ,已为许多研究者所关注[1,2 ] 。文献[3 ] 报道了以异丙醇钛和醋酸钡为原料 ,采用溶胶 凝胶法制备钛酸钡物体的研究 ,但未见有以钛酸丁酯及醋酸钡为原料制备钛酸钡…     

柠檬酸络合法制备La2CuO4纳米晶

以硝酸镧和硝酸铜为起始原料,柠檬酸为络合剂,采用溶胶-凝胶法制备了La₂CuO₄纳米晶。通过X射线衍射、场发射扫描电子显微镜、透射电子显微镜研究了柠檬酸的加入量对La₂CuO₄纳米粉体相组成、显微结构的影响,并采用Kissinger方法研究了La₂CuO₄纳米晶的合成活化能。结果表明：600 ℃煅烧保温2 h后,可获得单一物相的La₂CuO₄,晶粒为类钙钛矿型结构,晶粒尺寸为60~80 nm,分布集中;在制备过程中提高柠檬酸的加入量能够降低La₂CuO₄晶体的合成活化能,当柠檬酸与溶液中阳离子(La³⁺和Cu²⁺)的物质的量的比由1∶1增加至1.5∶1时,La₂CuO₄纳米晶的合成活化能由147.0 kJ·mol^-1降低到133.4 kJ·mol^-1。     

热爆合成三铝化钛复杂反应动力学的差示扫描量热法

用Friedman法研究了非等温DSC条件下热爆合成反应Ti 3Al→TiAl3的复杂反应动力学。根据表观激活能（Ea）随转化率（α）的变化关系，识别出该反应至少包含3个Ea值分别为109、175和89kJ/mol的子过程。通过与Ti-Al二元系的反应和互扩散激活能的比较，提出了可能的复杂反应动力学机制。     

吲唑、3-卤代吲唑互变异构反应机理的理论研究

The molecular structures of indazole and 3-halogeno-indazole tautomers were calculated by the B3LYP method at the 6-311G** level, both in the gaseous and aqueous phases, with full geometry optimization.The geometry and electronic structure of the tautomers of indazole, 3-halogeno-indazole and their transition states were obtained. The Onsager solvate theory model was employed for the aqueous solution calculations.The results of the calculation indicated that the N1-H form of the studied molecule is more stable than that of the N2-H form. The influences of the different 3-halogeno and solvent effects on the geometry, energy,charge and activation energy were discussed. The reaction mechanism of the tautomerization of indazole and 3-halogeno-indazole was also studied and a three-membered cyclic transition state of the tautomer reaction has been obtained.     

CF3O2自由基和NO反应机理的理论研究

用密度泛函理论(DFT)的B3LYP方法, 分别在6-31G、6-311G、6-311+G(d)基组水平上研究了CF3O2自由基和NO反应机理. 研究结果表明, CF3O2自由基和NO反应存在三条可行的反应通道, 优化得到了相应的中间体和过渡态. 从活化能看, 通道CH3O2+NO→IM1→TS1→IM2→TS2→CF3O+ONO的活化能最低, 仅为70.86 kJ•mol-1, 是主要反应通道, 主要产物是CF3O和NO2. 而通道CH3O2+NO→IM1→TS3→CF3ONO2和CH3O2+NO→TS4→IM3→TS5→IM4→TS6→CF3O+NOO的活化能较高, 故该反应难以进行.     

Thermal kinetics and morphological investigation of alkaline treated rice husk biomass

Agro waste bio mass are creating challenges for environment in term of air pollution due to improper disposal. Rice milling is the process in which rice husk is produced as by-product. The agro-waste rice husk has tremendous potential to be used either in its raw form or in ash form. The inherent component of this waste cellulose provides enhanced properties in a reinforced composite when used as filler. Rice husk is the hard outer layer and covering rice seed, which makes reinforcement challenging in its original form. Fiber surface treatment significantly improves adhesion with matrix and various thermo chemical properties of filler as well as of composites. NaOH treatment is cost-effective and it ensures the adhesion with matrix by removal of hemicellulose and lignin. The chemical treatment of agro-waste (rice husk) is performed with 5% alkali solutions of NaOH in water. Results are compared with the properties of untreated rice husk for thermal and morphological characterizations. In the present work, we are trying to quantify the impact of chemical treatment on rice husk thermal decomposition and its kinetics. Thermogravimetric analysis and kinetics study of thermal degradation, provide key input towards pyrolysis pattern of rice husk, while FTIR and SEM analysis provide the prospects of this bio filler using a reinforcing agent to develop green composite and productive disposal. The FTIR data helps to find the possibilities of blending different bio fillers and natural fibers to find suitable reinforcing substances. The average activation energy of treated fiber is noted as 137.95 by KAS method and 108.08 by FWO method as compared to 55.56 by KAS method & 54.26 by FWO method for untreated rice husk.     

掺杂Ag纳米BaTiO3抑菌剂的制备及其性能

掺杂Ag纳米BaTiO3抑菌剂的制备及其性能;溶胶-凝胶;掺杂Ａｇ;ＢａＴｉＯ３;抑菌性能     

热分析动力学研究方法的新进展

"非等温动力学"作为热分析动力学研究的核心,已经被广泛应用于化学、化工、冶金、地质、药物和环保等重要领域。热分析动力学研究的主要任务是确定机理函数、活化能和指前因子等动力学参数。在众多的热分析动力学研究方法中,"等转化率法"由于其可以在不涉及动力学模式函数的前提下,获得较为可靠的活化能值,因此被国际热分析与量热学协会(ICTAC)推荐使用。本文简要介绍了近十年来提出的热分析动力学研究方法,特别是等转化率方法的研究进展情况,评述了各种方法的特点与局限。同时,展望了热分析动力学研究方法未来的发展趋势。     

CH3CF2O2与HO2自由基反应机理的理论研究

用密度泛函理论(DFT)的B3LYP方法，在6-311G、6-311+G(d)、6-311++G(d, p) 基组水平上研究了CH₃CF₂O₂与HO₂自由基反应机理. 结果表明, CH3CF₂O₂与HO₂自由基反应存在两条可行的通道. 通道CH3CF₂O₂＋HO₂→IM1→TS1→CH₃CF₂OOH＋O₂的活化能为77.21 kJ•mol^－1，活化能较低，为主要反应通道，其产物是O₂和CH₃CF₂OOH. 这与实验结果是一致的；而通道CH₃CF₂O₂＋HO₂→IM2→TS2→IM3→TS3→IM4＋IM5→IM4＋TS4→IM4＋OH＋O₂→TS5＋OH＋O₂→CH₃＋CF₂O＋OH＋O₂→CH₃OH＋CF₂O＋O₂的控制步骤活化能为93.42 kJ•mol^－1，其产物是CH₃OH、CF₂O和O₂. 结果表明这条通道也能发生，这与前人的实验结果一致.     

在Pt/HZSM-5双功能催化剂上FCC汽油加氢异构化反应机理及动力学研究

在活性趋于稳定的Pt/HZSM-5双功能催化剂上，利用连续流动微反一色谱装置，进行了催化裂化汽油加氢异构化反应机理和动力学的研究．在250-330℃，1．0-3．0MPa反应条件下，考察了催化汽油加氢异构化反应产物分布，按单分子反应机理，建立了催化裂化汽油中烯烃加氢异构化反应网络和动力学模型，计算了反应网络中各步的反应速率常数和活化能．结果表明：Pt／HZSM-5双功能催化剂具有较好的加氢和异构活性，在保证辛烷值不下降的条件下，可使催化裂化汽油中烯烃加氢饱和，达到降低汽油烯烃和提高安定性的目的．     

Non-isothermal kinetics of reactions whose activation energy depends on the degree of conversion

A procedure for evaluating the non-isothermal kinetic parameters of reactions for which the activation energy depends on the degree of conversion is suggested. The procedure has been applied to the dehydration of calcium oxalate monohydrate and to the thermal degradation of poly(vinyl chloride) (PVC) and polychloroprene rubber.     

Thermal stability and degradation kinetics of novel organic/inorganic epoxy hybrid containing nitrogen/silicon/phosphorus by sol-gel method

Hybrids containing silicon, phosphorous and nitrogen were prepared by the sol-gel method and compared with pure epoxy. The silicon, phosphorous and nitrogen components were successfully incorporated into the networks of polymer. Thermogravimetric analysis (TGA) was used for rapid evaluation of the thermal stability of different materials. The integral procedure decomposition temperature (IPDT) has been correlated the volatile parts of polymeric materials and used for estimating the inherent thermal stability of polymeric materials. The IPDT of pure epoxy was 464 °C and the IPDTs of hybrids were higher than that of pure epoxy. The thermal stability of hybrids increased with the contents of inorganic components. The inorganic components can improve the thermal stability of pure epoxy.Two methods have been used to study the degradation of hybrids containing silicon, phosphorous and nitrogen hybrid during thermal analysis. These investigated methods are Kissenger, Ozawa's methods. The activation energies (E_a) were obtained from these methods and compared. It is found that the values of E_a for modified epoxy hybrids are higher than that of pure epoxy. The hybrids of high activation energy possess high thermal stability.