羟基硅酸镁纳米管负载非晶态Co-B催化环己烯氢甲酰化

采用浸渍化学还原法制备羟基硅酸镁纳米管(MgSNTs)负载非晶态钴硼催化剂(Co-B/MgSNTs)。应用X衍射技术(XRD),透射电子显微镜(TEM),X射线光电子能谱仪(XPS),元素分析(ICP)和比表面积(BET)分析等手段对催化剂进行了表征。研究了催化剂对于环己烯氢甲酰化反应的催化活性及循环使用。研究结果表明,具有高比表面积(250 m2·g-1)、较强耐受性和稳定性的MgSNTs可以有效的分散金属粒子,防止活性中心团聚和流失,催化环己烯的转化率为75.8%,醛的选择性为65.8%,实验重复3次以上,催化剂依然保持良好的催化活性和选择性。     

磷酸镍纳米管的合成及其催化环己烯环氧化反应性能

 在不添加有机模板剂的情况下, 通过尿素缓慢分解调节局部 pH 值, 水热法合成了具有均一孔道直径的磷酸镍纳米管材料 (NiPO-NTs). 采用 N2 吸附-脱附、吡啶吸附红外光谱和氨程序升温脱附对材料进行了表征, 并将其用于催化 H2O2 氧化的环己烯反应中, 考察了反应条件对环氧化反应性能的影响. 结果表明, NiPO-NTs 具有狭窄的孔径分布, 比表面积为 96.6 m2/g, 其表面酸中心以弱 Lewis 酸为主. 该反应中以乙腈为溶剂较为适宜, 高温和高 H2O2/环己烯摩尔比有利于提高环己烯转化率; 而低温和高 H2O2/环己烯摩尔比有利于提高环氧环己烷选择性. 在 60 oC, H2O2/环己烯摩尔比为 3, 反应 6 h 时, 环己烯转化率可达 50.6%, 环氧环己烷选择性为 72.1%.     

棕色环反应产物中铁氧化态的讨论

The oxidation state of iron in the "brown-ring" reaction product[Fe(NO)(H₂O)₅]²⁺ and the bond between Fe and NO in this cation are discussed in detail. After presenting different views from the literature based on experimental evidences and theoretical calculations, the oxidation state of iron resonates between +2 and +3 inclining to +2. The Fe-N-O bond angle is 180°. In addition, we proposed an explanation for the slightly shortening of the bond length of NO after coordination to the iron ion.     

径向电场对纳米管中水分子通量的影响

水分子在纳米通道中的运动对于生命活动、纳米器件的设计等都有着重要的意义. 现在已经证实, 在(6,6)的碳纳米管中, 水分子会以单分子水链的形式协同通过碳纳米管. 但是如何控制水分子的流量仍然是一个困难的课题. 本文研究了在径向电场作用下, 碳纳米管中水分子通量的变化趋势和碳纳米管的开关行为.发现在碳纳米管两端存在200 MPa的压力差时, 电场强度从1 V·nm^-1增加到3 V·nm^-1, 水分子通量线性减小. 当径向电场强度增加到3 V·nm^-1时, 碳纳米管处于关闭状态, 水分子无法通过碳纳米管. 进一步, 我们发现水偶极与碳纳米管管轴夹角的平均值的概率分布和翻转频率都与水分子在纳米管中的个数有很大关系.     

硼氮纳米管导电性与成键性的理论研究

用密度泛函的B3LYP方法对zigzag型(N,0)和armchair型(N,N)硼氮纳米管(N=4,5,6)进行了理论计算,根据其能带结构、态密度和健级讨论了四硼氮纳米管的成健作用和导电性,并与碳纳米管做比较.     

原子和简单分子失电子后的体积变化

本文在对比分析一些分子及其一价阳离子的键长的基础上,运用分子轨道理论和共振论成功地解释了实验数据,以及部分分子的阳离子比相应分子的键长大的原因。并对分子失电子后体积变化的规律作了一些有益的探讨     

5,6,9,10-四脱氢苯并环辛烯结构和性质的理论研究

在RHF/6-31G^**,MP2/6-31G^**,B3LYP/6-31G^**水平下优化了5,6,9,10-四脱氢苯并环辛烯的平衡几何构型。用B3LYP/6-31G^**方法计算了该化合物的红外光谱、拉曼光谱、核磁共振谱。计算结果与实验结果吻合很好,从而在理论上证实了它的存在。用等键反应分析,自然键轨道方法对它的稳定性和共轭性分别进行了讨论。结果表明5,6,9,10-四脱氢苯并环辛烯分子平面刚性结构,可能稳定存在,但由于苯环共轭性的削弱和较高的张力,使得它易于分解。     

纳米管钛酸和二氧化钛的暗态吸附性能

研究了在暗态下纳米管钛酸,TiO2(A),P25TiO2对水溶液中活性艳红X 3B的吸附性能.结果表明,pH值不同时,三者对活性艳红X-3B的吸附量不同,分析了它们吸附性能不同的原因.     

H2与C,BN和GaN纳米管的相互作用势能

基于C,B,N和Ga与H原子间的L-J势函数,系统计算了H2处于(n,n)(n=8,10,12)单壁C,BN和GaN纳米管内部及外部不同处的势能.根据势能变化曲线,分析了3种纳米管氢物理吸附能力的差异,给出了H2在3种纳米管外部的势能表达式.研究结果表明:3种纳米管内部的氢吸附力均分别高于管外;随着纳米管直径的增加,各纳米管管内的氢吸附力均略有下降,而管外变化不明显;GaN,BN和C纳米管依次具有更好的储氢能力.     

含磷/氮/硫环交联磷腈微纳米管的合成及对环氧树脂的阻燃作用

采用原位模板法,以六氯环三磷腈(HCCP)和二羟基二苯砜(BPS)为原料合成了一种环状交联型不溶不熔的磷腈大分子——聚环三磷腈-二羟基二苯砜(PZS)微纳米管,研究了PZS对环氧树脂(EP)的阻燃作用及阻燃机理.利用红外光谱(FTIR)、扫描电子显微镜(SEM)及透射电子显微镜(TEM)对PZS微纳米管进行了表征;采用热重分析(TG)考察了EP/PZS阻燃材料的热稳定性,并通过极限氧指数(LOI)和微型量热分析(MCC)测试了EP/PZS的阻燃性能.热降解实验结果表明,PZS微纳米管的加入使环氧树脂热降解温度降低,但残炭率显著提高.PZS微纳米管可以显著提高环氧树脂的阻燃性能,当阻燃剂添加量为5%时,环氧树脂的残炭率提高了46%,热释放速率峰值降低了约40%;LOI值从纯环氧树脂的26.0%提高到了30.6%.PZS微纳米管的加入还增强了环氧树脂的力学强度.阻燃性能的显著提高和力学性能的改善归因于PZS微纳米管在环氧树脂基体中的良好分散,以及燃烧炭化过程中生成的石墨化程度较高的类石墨烯结构的残炭,具有较高的抗氧化能力.研究结果表明,PZS微纳米管是一种优良、高效的具有潜在应用价值的阻燃剂.     

A Simple Theoretical Model for Ring and Nanotube Radial Breathing Mode

The radial breathing modes (RBMs) of (MgO)_n and (BeO)_n rings (n=3-10) were calculated using the density functional theory at B3LYP/6-31G(d) level. It was found that for large rings, the radial breathing mode (RBM) frequency was inversely proportional to the centre diameter, but the variation of bond length may lead to deviations from a linear behavior. The deviations caused by inverse cubic term of diameter and variation of bond length, became dramatic with the decrease of ring diameter. From the point of chemical bond view, using one-dimensional harmonic oscillator and the method of cascade and parallel connection of “springs”, the linear relation and deviations were explained. The model can be applied to nanotubes.     

六氟乙烷分解成氟甲基及其逆反应的A因子和活化能的计算

采用半经典统计方法对过渡态的临界键长进行了具体计算,利用这些结果计算了CF_3+CF_3C_2F_6反应的指数前因子和活化能,计算结果与实验值相当符合。     

A Dynamic Model and Parameter Identification of High Viscosity Magnetorheological Fluid-Based Energy Absorber with Radial Flow Mode

The excellent suspension stability of the high-viscosity linear polysiloxane magnetorheological fluid (HVLP MRF) makes it a great controlled medium for magnetorheological energy absorbers (MREAs). In our previous work, the Herschel–Bulkley flow model (HB model) was used to describe the shear-thinning rheological behavior and establish the dynamic model of an HVLP MRF-based MREA with radial flow mode. However, as the established model was implicit, the MREA response time increased and the buffer effect was degraded. To improve the time response characteristics, an explicit dynamic model based on the HB model incorporating minor losses (called the E-HBM model) is proposed in this study. The model parameters were identified based on the HBM model. To verify the E-HBM model, five evaluation parameters for the energy absorption performance of the MREA, that is, peak force, mean force, crush force efficiency, specific energy absorption, and stroke efficiency, were introduced to compare the theoretical results with the experimental results obtained using a high-speed drop tower facility with a mass of 600 kg. Then, the relative error of the crush force efficiency, specific energy absorption, and stroke efficiency was quantitatively and comprehensively analyzed considering the E-HBM model and experimental results. The results indicate that the proposed E-HBM model agrees with the impact behavior of the radial flow mode MREA.     

A Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotube/Chitosan Composite as a New Sensor for Simultaneous Determination of Acetaminophen and Mefenamic Acid in Pharmaceutical Preparations and Biological Samples

A new chemically modified electrode is constructed based on multiwalled carbon nanotube/chitosan modified glassy carbon electrode (MWCNTs‐CHT/GCE) for simultaneous determination of acetaminophen (ACT) and mefenamic acid (MEF) in aqueous buffered media. The measurements were carried out by application of differential pulse voltammetry (DPV), cyclic voltammetry (CV) and chronoamperometry (CA) methods. Application of DPV method showed that the linear relationship between oxidation peak current and concentration of ACT and MEF were 1 μM to 145 μM, and 4 μM to 200 μM, respectively. The analytical performance of this sensor has been evaluated for detection of ACT and MEF in human serum, human urine and a pharmaceutical preparation with satisfactory results.     

A New Target for Synthesis: Theoretical Prediction for the Reaction between Boron Nitride Nanotube and Dichlorocarbene

Understanding the chemistry of BNNT is a crucial step toward their ultimate practical use. A comparative study of Reactions A （ASWCNT （5,5） and CCl2） and B （ASWBNNT （5,5） and CCl2） have been performed by using ONIOM （B3LYP/6-31G＊： AM1） method in Gaussian03 program package. The results show that （1） the two reactions are both exothermic; （2） the mechanism of Reaction B is a two-step mechanism; （3） the difference in energy barriers suggests that the reaction of CCl2 with BNNT is easier than with CNT; （4） in reaction B, CCl2 prefers to attack the boron atom of BNNT first.     

A Simple,Selective, and General Catalyst for Ring Closing Depolymerization of Polyesters and Polycarbonates for Chemical Recycling

The ability to efficiently and selectively process mixed polymer waste is important to address the growing plastic waste problem. Herein, we report that the combination of ZnCl₂ and an additive amount of poly(ethylene glycol) under vacuum can readily and selectively depolymerize polyesters and polycarbonates with high ceiling temperatures (T_c>200 °C) back to their constitute monomers. Mechanistic experiments implicate a random chain scission mechanism and a catalyst structure containing one equivalent of ZnCl₂ per ethylene glycol repeat unit in the poly(ethylene glycol). In addition to being general for a wide variety of polyesters and polycarbonates, the catalyst system could selectively depolymerize a polyester in the presence of other commodity plastics, demonstrating how reactive distillation using the ZnCl₂/PEG600 catalyst system can be used to separate mixed plastic waste.     

近红外光谱分析模型传递简易方法研究

本文在不同时间安装的多台同型号近红外光谱仪上建立推进剂校正模型时,由于推进剂样品数量少且难于保存,新到仪器在建模时常遇到代表性样品数量严重不足.为此,提出将2台波长一致性好的近红外光谱仪器上采集的光谱组成一个混合校正样品光谱集,使用偏最小二乘法(PLS)建立模型的方法.结果表明,在用户缺少专业模型传递软件情况下,该方法...     

Intramolecular 1,3‐Dipolar Cycloaddition‐Mediated Stereoselective Synthesis of Disubstituted Cyclopentane: A Simple Model for the Cyclopentane Ring System of Polycyclic Oroidine Alkaloids

We present a diastereoselective synthesis of disubstituted cyclopentane 8 having a nitrogen‐containing quaternary carbon center, which is found in axinellamine A ( 5 ) and related compounds. During this work, we found that the 1,3‐dipolar cycloaddition product 24 immediately underwent intramolecular redox reaction at the newly formed morpholin‐2‐one moiety, thus affording disubstituted cyclopentane containing a tertiary amine ( 9 ) stereoselectively in good yield. The amine 9 was successfully converted into guanidine 31 , which corresponds to 8 , through iminium cation–enamine isomerization.     

A Simple and Effective Model for Modeling of Convective Drying of Sewage Sludge: The Reaction Engineering Approach (REA)

Sludge drying is an essential step to reduce the cost of waste treatment but design of sewage sludge dryer is still relatively complicated since the drying kinetics is influenced signficantly by shrinkage, cracking and skin formation which occur during drying. In this study, the REA (reaction engineering approach) is implemented for the first time to model the convective drying of sewage sludge, a highly shrinkable material. The equilibrium activation energy (ΔEv,b) is evaluated according to the corresponding drying air humidity and temperature. This is combined with the relative activation energy (ΔEv/ΔEv,b), generated from one accurate drying run to produce the activation energy, which describes the internal behavior of the samples during drying. A good agreement between experimental and predicted data is observed. The REA is shown to perform comparable or even better than the classical diffusion-based model. It can be said that the REA can model the convective drying of sewage sludge well. The REA can be implemented for further applications including design and evaluation of sludge dryer.